Nitrogen symbiotically fixed by cowpea and gliricidia in traditional and agroforestry systems under semiarid conditions

The objective of this work was to estimate the amounts of N fixed by cowpea in a traditional system and by cowpea and gliricidia in an agroforestry system in the Brazilian Northeast semiarid. The experiment was carried out in a randomized complete block design, in a split-plot arrangement, with four replicates, in the semiarid region of the state of Paraíba, Brazil. Plots consisted of agroforestry and traditional systems (no trees), and split-plots of the three crops planted between the tree rows in the agroforestry system. To estimate N fixation, plant samples were collected in the fourth growth cycle of the perennial species and in the fourth planting cycle of the annual species. In the agroforestry system with buffel grass and prickly-pear cactus, gliricidia plants symbiotically fix high proportions of N (>50%) and contribute with higher N amounts (40 kg ha-1 in leaves) than in the traditional system (11 kg ha-1 in grain and 18 kg ha-1 in straw). In the agroforestry system with maize and cowpea, gliricidia plants do not fix nitrogen, and N input is limited to the fixation by cowpea (2.7 kg ha-1), which is lower than in the traditional system due to its lower biomass production.

Dry matter accumulation and mineral nutrition of arracacha in response to nitrogen fertilization

Abstract:The objective of this work was to evaluate the effect of nitrogen fertilization on the growth and yield of arracacha (Arracacia xanthorrhiza), as well as on the plant's nutrient uptake, distribution, and removal. The experiment was carried out in a typical Oxisol, with sandy texture. A randomized complete block design was used, with four replicates. The treatments consisted of five N rates: 0, 50, 100, 200, and 400 kg ha-1. The plots were composed of three 8-m-length rows, spaced at 0.60 m between rows and 0.40 m between plants. The plants were harvested after an 8-month cycle. Nitrogen fertilization significantly increased the proportion of N and S accumulated in stems, and of Ca, Mg, Fe, and Mn in leaves. N supply increased Zn distribution to stems and leaves, whereas high N rates increased Cu allocation to stems more than to the rootstock. High N rates increase plant dry matter (DM) production and nutrient uptake and removal, but do not result in the greatest yield due to the greater development of leaves and stems, and to the lower allocation of DM in storage roots.

Sugarcane response to nitrogen rates, measured by a canopy reflectance sensor

Abstract:The objective of this work was to evaluate whether a canopy sensor is capable of estimating sugarcane response to N, as well as to propose strategies for handling the data generated by this device during the decision-making process for crop N fertilization. Four N rate-response experiments were carried out, with N rates varying from 0 to 240 kg ha-1. Two evaluations with the canopy sensor were performed when the plants reached average stalk height of 0.3 and 0.5 m. Only two experiments showed stalk yield response to N rates. The canopy sensor was able to identify the crop response to different N rates and the relationship of the nutrient with sugarcane yield. The response index values obtained from the canopy sensor readings were useful in assessing sugarcane response to the applied N rate. Canopy reflectance sensors can help to identify areas responsive to N fertilization and, therefore, improve sugarcane fertilizer management.

Carbon and nitrogen cycling in an integrated soybean-beef cattle production system under different grazing intensities

Abstract:The objective of this work was to evaluate the effect of grazing intensity on the decomposition of cover crop pasture, dung, and soybean residues, as well as the C and N release rates from these residues in a long-term integrated soybean-beef cattle system under no-tillage. The experiment was initiated in 2001, with soybean cultivated in summer and black oat + Italian ryegrass in winter. The treatments consisted of four sward heights (10, 20, 30, and 40 cm), plus an ungrazed area, as the control. In 2009-2011, residues from pasture, dung, and soybean stems and leaves were placed in nylon-mesh litter bags and allowed to decompose for up to 258 days. With increasing grazing intensity, residual dry matter of the pasture decreased and that of dung increased. Pasture and dung lignin concentrations and C release rates were lower with moderate grazing intensity. C and N release rates from soybean residues are not affected by grazing intensity. The moderate grazing intensity produces higher quality residues, both for pasture and dung. Total C and N release is influenced by the greater residual dry matter produced when pastures were either lightly grazed or ungrazed.

Effect of nitrogen and phosphorus supply on growth, chlorophyll content and tissue composition of the macroalga Chaetomorpha linum (O.F. Mull), Kutz, in a Mediterranean Coastal Lagoon

The effect of dissolved nutrients on growth, nutrient content and uptake rates of Chaetomorpha linum in a Mediterranean coastal lagoon (Tancada, Ebro delta, NE Spain) was studied in laboratory experiments. Water was enriched with distinct forms of nitrogen, such as nitrate or ammonium and phosphorus. Enrichment with N, P or with both nutrients resulted in a significant increase in the tissue content of these nutrients. N-enrichment was followed by an increase in chlorophyll content after 4 days of treatment, although the difference was only significant when nitrate was added without P. P-enrichment had no significant effect on chlorophyll content. In all the treatments an increase in biomass was obseved after 10 days. This increase was higher in the N+P treatments. In all the treatments the uptake rate was significantly higher when nutrients were added than in control jars. The uptake rate of N, as ammonium, and P were significantly higher when they were added alone while that of N as nitrate was higher in the N+P treatment. In the P-enriched cultures, the final P-content of macroalgal tissues was ten-fold that of the initial tissue concentrations, thereby indicating luxury P-uptake. Moreover, at the end of the incubation the N:P ratio increased to 80, showing that P rather than N was the limiting factor for C. linum in the Tancada lagoon. The relatively high availability of N is related to the N inputs from rice fields that surround the lagoon and to P binding in sediments.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Effects of nitrogen supply on wheat and on soil nitrate

Field experiments were conducted at two locations during two growing seasons in the Ebro Valley (Spain), to evaluate the effects of N fertilization on yield and quality of Mediterranean-type wheat in irrigated conditions. Seven N treatments and a control were investigated. The average grain yields ranged from 2117 to 5551 kg ha-1 depending on the year and location. Grain protein ranged from 14.25 to 16.9%, and other quality parameters such as the dough strength (W) also varied with year and location, confirming the suitability of Mediterranean-type wheat and the climate for the production of good bread-making quality wheat. However, grain yields are normally low and both yields and quality can be greatly affected by the variability of this type of climate, even under irrigation. Under these conditions, grain yield increases were mainly due to an increase in the number of grains per m2 without a reduction in the N content per spike, suggesting that N in the grain was not source-limited, possibly due to the lower grain yields and relatively high soil nitrate concentrations. In soils with lower initial soil NO-3N contents, better grain yields could be achieved by applying a N fertilizer rate of about 100 kg N ha-1, whereas in soils with high initial NO-3N contents, no N or a maximum rate of 50 kg N ha-1 is needed to obtain a good grain quality, showing the possibility of producing high-quality wheat with a low amount of N fertilizer and thus increasing the sustainability of the cropping system.

Response of wheat to additional nitrogen fertilizer application after pig slurry on over-fertilized soils

Pig slurry is a valuable nutrient resource but constitutes a waste disposal problem in areas of high animal density. In the semiarid area of Pla d’Urgell, in the Ebro Valley, North-East Spain, irrigated crops receive large amounts of nutrients in the form of manure and mineral fertilizers. We studied the effect of pig slurry and additional side-dress mineral fertilizers on irrigated wheat, Triticum aestivum L., on a coarse loam soil, with high soil P and K levels. Yields increased by 62.3% when using pig slurry. The application of ammonium sulfate nitrate sidedress did not significantly increase wheat production. The average apparent recoveries were higher for potassium (88.7%) than for nitrogen (51.3%) and phosphorus (36.3%). Greater amounts of soil NO3-N were measured over the four growing seasons, which was consistent with the amount of N applied. Macronutrient and micronutrient uptake was significant higher for pig slurry treatments, but only small differences were found between the pig slurry and pig slurry plus ammonium sulfate nitrate treatments. The unfertilized treatment showed significantly lower soil P, K, Cu and Zn content than pig slurry treatments; 34%, 21%, 34%, and 26% respectively. These findings could be used to develop a nutrient management plan based on knowledge of soil test results and crop nutrient removal. This could help to improve the use of pig slurry and mineral fertilizers on limited available land areas and prevent the accumulation of potentially toxic elements in soils and the export of nutrients through agricultural drainage.

Use of a pre-sidedress soil nitrate test (PSNT) to determine nitrogen fertilizer requirements for irrigated corn

In the present study, a 2-year N rate response experiment was conducted in different fields to monitor NO3-N soil profiles, N accumulation by the crop and final crop performance, in order to assess if soil NO3-N at pre-sidedressing (Pre-Sidedress Soil Nitrate Test, PSNT) is a reliable indicator for soil N availability for corn in the irrigated area served by canal d’Urgell (Lleida, Spain), and if the test can be used to separate responsive fields from non-responsive fields to sidedress N fertilizer applications. Preliminary soil N availability (N sidedress fertilizer rate + PSNT) critical levels to identify fields that need supplementary N fertilizer applications were established at ca. 300 and 210 kg NO3-N·ha–1, for PSNTrooting–zone and PSNT0–30 cm, respectively (for a yield goal of 14 t grain·ha–1).

Variation of grain nitrogen content in relation with grain yield in old and modern Spanish wheats grown under a wide range of agronomic conditions in a Mediterranean region

Wheat yield and grain nitrogen concentration (GNC; mg N/g grain) are frequently negatively correlated. In most growing conditions, this is mainly due to a feedback process between GNC and the number of grains/m2. In Mediterranean conditions, breeders may have produced cultivars with conservative grain set. The present study aimed at clarifying the main physiological determinants of grain nitrogen accumulation (GNA) in Mediterranean wheat and to analyse how breeding has affected them. Five field experiments were carried out in north-eastern Spain in the 2005/06 and 2006/ 07 growing seasons with three cultivars released at different times and an advanced line. Depending on the experiment, source-sink ratios during grain filling were altered by reducing grain number/m2 either through pre-anthesis shading (unshaded control or 0.75 shading only between jointing and anthesis) or by directly trimming the spikes after anthesis and before the onset of the effective grain filling period (un-trimmed control or spikes halved 7–10 days after anthesis). Grain nitrogen content (GN content ; mg N/grain) decreased with the year of release of the genotypes. As the number of grains/m2 was also increased by breeding there was a clear dilution effect on the amount of nitrogen allocated to each grain. However, the increase in GN content in old genotypes did not compensate for the loss in grain nitrogen yield (GNY) due to the lower number of grains/m2. GN content of all genotypes increased (increases ranged from 0.13 to 0.40 mg N/grain, depending on experiment and genotype) in response to the post-anthesis spike trimming or pre-anthesis shading. The degree of source-limitation for GNA increased with the year of release of the genotypes (and thus with increases in grain number/m2) from 0.22 (mean of the four manipulative experiments) in the oldest cultivar to 0.51 (mean of the four manipulative experiments) in the most modern line. It was found that final GN content depended strongly on the source-sink ratio established at anthesis between the number of grains set and the amount of nitrogen absorbed at this stage. Thus, Mediterranean wheat breeding that improved yield through increases in grain number/m2 reduced the GN content by diluting a rather limited source of nitrogen into more grains. This dilution effect produced by breeding was further confirmed by the reversal effect produced by grain number/m2 reductions due to either pre-anthesis shading or post-anthesis spike trimming.

Use of nitrification inhibitor DMPP to improve nitrogen recovery in irrigated wheat on a calcareous soil

The 3,4-dimethyilpyirazole phosphate (DMPP), commercialized as Entec, is a nitrification inhibitor developed by BASF (Germany) that may help to minimize N losses and to obtain a higher profit from N fertilizers. A two-year field trial was established in 2001 in the Northeast of Spain to assess the effects of DMPP on N use efficiency (NUE) and to determine the economic returns. Seven treatments have been carried out comparing the effect of DMPP on pig slurry and on mineral fertilizers. The application of DMPP resulted in better efficiency indexes on mineral fertilizers. An apparent nitrogen recovery of 0.465 kg kg-1, on average, was obtained for the Entec treatment. A net benefit of € 809 ha-1, on average, was obtained for the Entec treatment compared with € 607 ha-1 for the control treatment. The results of this study suggest that the nitrification inhibitor could improve farmer profit in irrigated wheat on a calcareous soil.

Nitrogen replacement value of alfalfa to corn and wheat under irrigated Mediterranean conditions

In crop rotations that include alfalfa (Medicago sativa L.), agronomic and environmental concerns mean that it is important to determine the N fertilizer contribution of this legume for subsequent crops in order to help to increase the sustainability of cropping systems. To determine the N fertilizer replacement value (FRV) of a 2-yr alfalfa crop on subsequent crops of corn (Zea mays L.) followed by wheat (Triticum aestivum L.) under irrigated Mediterranean conditions, two 4-yr rotations (alfalfa-corn-wheat and corn-corn-corn-wheat) were conducted from 2001 to 2004 in a Typic Xerofluvent soil. Corn yields were compared after two years of alfalfa and a third year of corn under monoculture and wheat yields were also compared after both rotations. Corn production after alfalfa outyielded monoculture corn at all four rates of N fertilizer application analyzed (0, 100, 200 and 300 kg N/ha). The FRV of 2-yr alfalfa for corn was about 160 kg N/ha. Wheat grown after the alfalfa-corn rotation outyielded that grown after corn under monoculture at both the rates of N studied (0 and 100 kg N/ha). The FRV of alfalfa for wheat following alfalfa-corn was about 76 kg N/ha. Soil NO3 -N content after alfalfa was greater than with the corn monoculture at all rates of N fertilizer application and this higher value persisted during the second crop after alfalfa. This was probably one of the reasons for the better yields associated with the alfalfa rotation. These results make a valuable contribution to irrigated agriculture under mediterranean conditions, show reasons for interest in rotating alfalfa with corn, and explain how it is possible to make savings when applying N fertilizer.

Effects of levels of nitrogen and potassium on yield and fruit maturation of irrigated guava trees in the São Francisco Valley

Yield and physical and chemical characteristics of 'Paluma' guava fruit were evaluated as a function of the harvest at different maturity stages, under influence of nitrogen and potassium fertilization, in Petrolina, State of Pernambuco, Brazil. Fertilizer rates were 67 kg N + 33 kg K2O, 133 kg N + 67 kg K2O, 200 kg N + 100 kg K2O and 267 kg N + 133 kg K2O per hectare. Fruits were evaluated at maturity stages 2, 3, 4 and 5, established according to peel color. Higher doses of N and K induced higher yields. Nevertheless, fertilization with 200 kg of N + 100 kg of K per hectare improved fruit quality, delaying ascorbic acid breakdown and conserving pulp firmness. Main changes took place at maturity stages 4 and 5, when the fruit should present ideal conditions for consumption, namely the increase on soluble solids and soluble sugars content.