Avaliação mecânica da colagem estrutural entre compósitos poliméricos e materiais metálicos utilizados em dutos petroquímicos

The development of technology for structural composites has as one of its ends form a set of materials that combine high values of mechanical strength and stiffness and low density. Today, companies like Embraer and PETROBRAS and research institutions like NASA, working with these materials with recognized advantages in terms of weight gain, increased performance and low corrosion. We have developed a systematic study to determine the bond strength between composite carbon fiber / epoxy and fiberglass / epoxy laminate both bonded to a carbon steel which are widely used in the petrochemical industry and repair. For morphological evaluation and bonding between materials of different natures, ultrasound analysis, optical microscopy and stereoscopy were performed. To simulate actual conditions, the composites were subjected to conditioning by using heat shock temperatures from -50 to 80 ° C for 1000 cycles for composite carbon fiber / epoxy composites and 2000 cycles for fiberglass / epoxy . The use of composites studied here proved to be efficient to perform repairs in metallic pipes with application petrochemical, as when exposed to sudden changes of temperature (-50 ° to 80 ° C) cycling at 1000 to 2000 times, its mechanical properties (shear and tensile) practically do not change

Obtenção e caracterização de compósitos via RTM com alta fração de fibras de carbono processados à temperatura ambiente

After confirming the high specific mechanical properties of composite materials by scientific studies conducted over the last decades, one of the challenges of this new class of materials is the ability to achieve mass production at a more affordable cost, which has become indispensable. The Resin Transfer Molding (RTM) is an excellent method for manufacturing composite materials. Despite being a process widely used by international companies in the production of high performance structural composites, only a short time the national aviation industry has shown interest in implementing this type of processing to more complex structures and greater structural responsibility. In aeronautical projects, the reproducibility and the relative low cost of this process, several studies have been performed in Brazil for learning and perfecting this technique. This process is suitable for producing polymer components both simple as complex geometry, and allows to achieve consistent thickness, with high quality finish and without limiting range. Polymeric composite components for the high mechanical stress applications such as aircraft structures, satellites, etc., require a strict control of volume fractions of the composite constituents, beyond the knowledge of their mechanical and thermal properties. Therefore, in this experimental work degree study on the mechanical, thermal and of porosity composites processed by RTM processed characterization was performed. This characterization was performed targeting a possible aerospace application of this composite material. For the production of composites, process equipment (RTM RTM injector Radius 2100cc) was used. The processed carbono/epoxy composites were characterized via flexure tests mechanically and thermally analysis via DMA, DSC and TGA. To determine the volume fraction of fibers, the composite samples were analyzed via matrix digestion (ASTM D3171) ... (Complete abstract click electronic access below)

Avaliação do efeito ambiental nas propriedades mecânicas e viscoelásticas de compósitos híbridos de titânio/fibra de carbono/resina epóxi

Hybrid composites combining metal plates and laminates with continuous fiber reinforced polymer, called fiber-metal (CHMF), have been particularly attractive for aerospace applications, due mainly to their high mechanical strength and stiffness associated with low density. These laminates (CHMF) consist of a sandwich structure consisting of layers of polymer composites and metal plates, stacked alternately. This setting allows you to combine the best mechanical performance of polymer composites reinforced with long fibers, to the high toughness of metals. Environmental effects should always be considered in the design of structural components, because these materials in applications are submitted to the effects of moisture in the atmosphere, the large cyclical variations of temperature around 82 ° C to -56 ° C, and high effort mechanical. The specimens of fibermetal composite were prepared at EMBRAER with titanium plates and laminates of carbon fiber/epoxy resin. This study aims to evaluate the effect of different environmental conditions (water immersion, hygrothermal chamber and thermal shock) of laminate hybrid titanium/carbon fiber/epoxy resin. The effects of conditioning were evaluated by interlaminar shear tests - ILSS, tensile, and vibration free

Processamento de peças em materiais compósitos para o projeto BAJA SAE

The weight of a vehicle has always been considered an extreme important factor, because it interferes in the performance, steering, consume, environmental impact, wear of components, among the others. Because of the new demand, consume reduction aim and gases emission increased the necessity to manufacture lighter vehicles, guaranteeing the complying with the gas emission international law. Besides the legal demand, the low weight will certainly be essential for the competitiveness for the next generation of vehicles. It is with this thinking the composite materials have been introduced in the automobilist industry, because those materials show an excellent relation of strength/weight, providing a reduction of consume and the increase of load capacity. Those factors justify the increase of interest of industry and the necessity of optimization of those materials and of their process. For this research, the field of application will be the Baja SAE Project, a project that is fully developed by engineering students, where they build a prototype single seat, off-road category, for use on hilly slopes with obstacle. This research aims to study two key components of the prototype are made of composite materials, analyzing all the processing. In addition, there is the analysis of the viability of this production parts to a Baja SAE vehicle, in order to increase their performance and reduce their weight without reducing the safety and robustness of the prototype. It was possible to achieve weight reduction of the steering subsystem with manufacturing the flywheel hybrid composite (carbon/glass) and the replacement of SAE 1010 steel by hybrid composite (carbon/aramid) in CVT box. The importance of this study is to obtain a good project for the vehicle of technical and scientific manner, contributing to the know-how to the team and providing a basis for optimization for upcoming projects

Influência do condicionamento ambiental sobre as propriedades viscoelásticas de compósitos aramida/epóxi

The increasing application of structural composites in the aerospace industry is mainly due to its low specific weight coupled with its excellent mechanical properties when in service. As a result of climatic variations that pass the aircraft is of paramount importance to study the influence of weathering on this type of material when subjected to such changes. The purpose of this work is to evaluate the mechanical behavior of specimens of kevlar fiber /epoxy matrix composites, by dynamic mechanical thermal analysis (DMA) and interlaminar shear strength tests (ILSS), after passing through three environmental conditioning: saline fog, hygrothermal and ultraviolet radiation. From the results, we concluded that the laminate was molded supplied homogeneously, not presenting problems such as porosity, delaminations or cracks inside. After a period of 625 hours of exposure to hygrothermal conditioning, we observed a 1,2% maximum of absorption of moisture. Samples subjected to the conditioning by UV irradiation (600 hours) and salt spray showed a reduction of about 24,30% and 32,30%, respectively, on the shear strength (ILSS). In DMA analysis is not observed significant changes on the glass transition temperature. However, when considering the storage modulus of the samples conditioned by UV radiation (1200 hours), salt spray and hygrothermal conditioning there is an increase of 5,34% , 7,19% and 5,57% respectively

Estudo de compósitos de madeira com reforço em bambu para utilização em mobiliário

Bamboo has been studied because of its peculiar mechanical properties and numerous possibilities of use, besides being a fast-growing grass and short cutting cycle. This study aimed to analyze the mechanical characteristics of wood-bamboo composite material, where the samples were developed from the combination of layers of bamboo as a structural reinforcement in solid pieces of pine and EGP panel parts. The species of wood used was Pinus taeda, and the bamboo species Guadua angustifolia and Dendrocalamus giganteus. All work was conducted at the Universidade Estadual Paulista - UNESP in the laboratory of Physical and Mechanical Properties of Wood. Tests including the density and tension parallel to grain of the bamboo species used and the static bending of composites in order to use this in the furniture industry. For the tests have been used as a basis the requirements of the normative document NBR 7190/97. The values obtained in the tests showed a significant increase in strength and stiffness compared to unreinforced parts, where there was an increase in MOE and MOR in static bending in all specimens used in evidence. The results showed the possibility of reducing sections in furniture components and the possibility of improving the mechanical properties of parts with defects found in wood of Pinus Itapeva region of São Paulo

Flexão e análise dinâmico-mecânica de compósitos 5HS e NCF com resina epóxi monocomponente produzidos por RTM

In order to study resin distribution and homogeneity of composite laminates manufactured by RTM, it was used CYCOM 890 monolithic toughened epoxy as a matrix with two different configurations of intermediated modulus (IM) carbon fibers: Satin Weave (5HS) and non crimp fabric (NCF). The injection parameters were defined based on Thermo Gravimetric Analysis (TG), Differential Scanning Calorimetry (DSC) and rheological analysis. After processing the material, the resin/fiber impregnation was studied using ultrasonic test, Thermo Gravimetric Analysis, Differential Scanning Calorimetry, Dynamic Mechanical Analysis (DMA) and flexural tests. Therefore, it was able to observe an internal residual stress during the cooling process in both laminates, higher in the composite using NCF fabric due to the lack of symmetry, although a good proportion of fiber/matrix has been verified by the lower values of flexural modulus deviation. The DMA enabled the visualization of glass transition and its association with the inter and intra molecular interaction and movement, in which the NCF composite presented better permeability due to the lowest temperature of glass transition, when compared to the Satin Weave composite

Obtenção de compósitos nanoestruturados PSU/nanotubos de carbono pela técnica de eletrofiação

The nanostructured materials over the last decade have been increasing the variety of studies and research applications in many industries. From the understanding and manipulation of nanoscale is possible to obtain high-performance materials. One method, which has been very effective in obtaining of nanostructured composites, is the electrospinning, a technique that uses electrostatic forces to produce fibers from a polymer solution. By understanding and controlling of process conditions, such as solution viscosity, working distance, the velocity of the collector, applied voltage and others conditions, it is possible to obtain fibers in many different morphologies. This work aims to obtain nanostructured composites from polysulfone (PSU) a thermoplastic polymer with high oxidation resistance and good mechanical strength at high temperatures and carbon nanotubes (CNTs) that are excellent reinforcements for polymer materials, their mechanical resistance is greater than that of all known materials; using the electrospinning process via polymer solution. Were used polysulfone solutions, n,n-ndimetil acetamide (PSU / DMAc) and this same solution added of CNTs in order to obtain the nanofibers. In both cases were analyzed the effectiveness of the process from the analysis of fiber diameters, rheological behavior and infrared spectroscopy. The results obtained confirmed the efficiency of the electrospinning process to obtain polymeric fibers

Comportamentos, térmico e mecânico, de compósitos de polipropileno e resíduo da hidrólise enzimática do bagaço de cana de açúcar

Pós-graduação em Engenharia Mecânica - FEG

Obtenção e caracterização térmica de compósitos nanoestruturados de resina fenol-furfurílica/CNT

Pós-graduação em Engenharia Mecânica - FEG

Obtenção e caracterização de compósitos nanoestruturados de poli(sulfeto de fenileno) reforçados com nanotubos de carbono

Pós-graduação em Engenharia Mecânica - FEG

Estudo da modificação superficial de fibras de carbono por meio de tratamentos a plasma para o aumento da adesão na interface de compósitos fibra de carbono/PPS

Pós-graduação em Engenharia Mecânica - FEG

Fadiga em compósitos 5HS carbono/epóxi processados via RTM: relação entre cargas axiais no plano e modos de delaminação

Pós-graduação em Engenharia Mecânica - FEG

Compósitos de nanocelulose / PHBV: manta microfibrilica por eletrofiação

Pós-graduação em Engenharia Mecânica - FEG

Otimização do processamento de partículas lead-free para aplicação em compósitos polímero/cerâmica com propriedades piezoelétrica e fotoluminescente

Pós-graduação em Química - IQ