An Effective Method of Determining the Residual Stress Gradients in a Micro-Cantilever

A method of determining the micro-cantilever residual stress gradients by studying its deflection and curvature is presented. The stress gradients contribute to both axial load and bending moment, which, in prebuckling regime, cause the structural stiffness change and curving up/down, respectively. As the axial load corresponds to the even polynomial terms of stress gradients and bending moment corresponds to the odd polynomial terms, the deflection itself is not enough to determine the axial load and bending moment. Curvature together with the deflection can uniquely determine these two parameters. Both linear analysis and nonlinear analysis of micro-cantilever deflection under axial load and bending moment are presented. Because of the stiffening effect due to the nonlinearity of (large) deformation, the difference between linear and nonlinear analyses enlarges as the micro-cantilever deflection increases. The model developed in this paper determines the resultant axial load and bending moment due to the stress gradients. Under proper assumptions, the stress gradients profile is obtained through the resultant axial load and bending moment.

Prevalencia de leptospirosis canina en la ciudad de Catacamas Olancho utilizando la tecnica de micro-aglutinacion 11 de marzo al 24 de julio

Con el objetivo de Contribuir a la mejora de la salud pública en la ciudad de Catacamas, Olancho, Honduras, mediante el diagnóstico de la prevalencia de Leptospirosis canina. Utilizando la técnica de Micro-aglutinación (MAT), para el registro y control de casos En el periodo del 11 de marzo al 24 de agosto del 2009. Para conocer la población canina con posibilidades de infestación con Leptospirosis según, sexo, edad, factores de riesgo. Y determinar el grado de infestación y una estrategia técnica y económica para el control y seguimiento contra la Leptospirosis. Se realizo un muestreo de 380 canes, correspondiente al 10% de la población canina en dicha ciudad. Extrayéndose 3 ml de sangre de la vena radial y safena externa, luego de procesarla para separar el suero mediante precipitación, fueron trasladados al laboratorio del INSTITUTO HONDUREÑO DE INVESTIGACIONES MEDICO VETERINARIO. Para su análisis mediante la técnica MAT. Luego se tomo una segunda muestra de orina a los animales reactivos, para realizar un cultivo haciendo uso de un medio de cultivo con antibiótico flurouracilo (5-fu) De acuerdo con los resultados obtenidos, de 380 canes, 5.1% son positivos y 94.9 % negativos a Leptospirosis encontrándose los siguientes serovares: canicola, icterohemorragica, hardjo, grippotyphosa.

Micro- and macroscopic characterizations of the viscoelastic fracture of resin-based fibre composites

Micro- and macroscopic characterizations of the viscoelastic fracture of a unidirectional carbon-fibre-reinforced epoxy composite are presented. First, the micro-cracking behavior of the material is studied by the use of scanning electron microscopy; the in situ creep cracking process is observed and the crack propagation is measured. In order to obtain insight into the mechanisms of the observed creep cracking, macroscopic investigations were also carried out. Finite-element method simulations were carried out to calculate the stress distribution and the variation of stresses with time. A theoretical analysis of the orthotropy of viscoelastic fracture behavior of the material is also conducted.

Experimental study on two-phase gas-liquid flow patterns at normal and reduced gravity conditions

Experimental studies have been performed for horizontal two-phase air-water flows at normal and reduced gravity conditions in a square cross-section channel. The experiments at reduced gravity are conducted on board the Russian IL-76 reduced gravity airplane. Four flow patterns, namely bubble, slug, slug-annular transition and annular flows, are observed depending on the liquid and gas superficial velocities at both conditions. Semi-theoretical Weber number model is developed to include the shape influence on the slug-annular transition. It is shown that its prediction is in reasonable agreement with the experimental slug-annular transition under both conditions. For the case of two-phase gas-liquid flow with large value of the Froude number, the drift-flux model can predict well the observed boundary between bubble and slug flows.

3D simulation of the micro indentation process and relative problems research

In this paper the finite element method was used to simulate micro-scale indentation process. The several standard indenters were simulated with 3D finite element model. The emphasis of this paper was the differences between 2D axisymmetric cone model and

Combined effect of surface tension, gravity and van der Waals force induced by a non-contact probe tip on the shape of liquid surface

Aiming at understanding how a liquid film on a substrate affects the atomic force microscopic image in experiments, we present an analytical representation of the shape of liquid surface under van der Waals interaction induced by a non-contact probe tip. The analytical expression shows good consistence with the corresponding numerical results. According to the expression, we find that the vertical scale of the liquid dome is mainly governed by a combination of van der Waals force, surface tension and probe tip radius, and is weekly related to gravity. However, its horizontal extension is determined by the capillary length.

Micro- and macro-tribological study on a self-assembled dual-layer film

A novel self-assembled dual-layer film as apotential excellent lubricant for micromachines was successfully prepared on single-crystal silicon substrate by chemical adsorption of stearic acid (STA) molecules on self-assembled monolayer of 3-aminopropyltri

Substrate Effects on the Micro/Nanomechanical Properties of TiN Coatings

Nanoindentation and nanoscratch tests were performed for titanium nitride (TiN) coatings on different tool steel substrates to investigate the indentation/scratch induced deformation behavior of the coatings and the adhesion of the coating–substrate interfaces and their tribological property. In this work, TiN coatings with a thickness of about 500 nm were grown on GT35, 9Cr18 and 40CrNiMo steels using vacuum magnetic-filtering arc plasma deposition. In the nanoindentation tests, the hardness and modulus curves for TiN/GT35 reduced the slowest around the film thickness 500 nm with the increase of indentation depth, followed by TiN/9Cr18 and TiN/40CrNiMo. Improving adhesion properties of coating and substrate can decrease the differences of internal stress field. The scratch tests showed that the scratch response was controlled by plastic deformation in the substrate. The substrate plays an important role in determining the mechanical properties and wear resistance of such coatings. TiN/GT35 exhibited the best load-carrying capacity and scratch/wear resistance. As a consequence, GT35 is the best substrate for TiN coatings of the substrate materials tested.

Evaluación de los factores de la ecuación universal de pérdidas de suelo en la micro cuenca "D", de la Cuenca Sur del Lago de Managua

El presente estudio se realizó en la micro cuenca "D", de la Cuenca Sur del Lago de Managua. Se determinaron los factores de la E.U.P.S., las pérdidas de suelo reales estimadas por la metodología de Coschoton y la influencia de la cobertura vegetal de los cultivos de maíz (60,81 l pts/ha) y frijol (225,225 pts/ha) en rotaciones únicas sembradas a curvas a nivel. Se utilizaron 6 parcelas de escurrimiento bajo la metodología de Wishmeier, con dimensiones de 2 m de ancho y 22.2 m de largo por cada parcela. Las variables evaluadas fueron las pérdidas de suelo reales por evento lluvioso, y los factores de la E.U.P.S. La información se presenta de forma descriptiva. Según datos obtenidos en el estudio demostraron que las parcelas desnudas presentaron las mayores pérdidas de suelo reales en el ciclo de primera como postrera, las parcelas cultivadas con maíz resultó ser más efectivo que las parcelas cultivadas con frijol en la época de primera, en postrera las pérdidas de suelo disminuyeron sustancialmente siendo las parcelas cultivadas con frijol las más efectivas dado que no presentó pérdidas de suelo. Los meses de Junio, Agosto y Septiembre son los meses con mayor susceptibilidad a las pérdidas de suelo coincidiendo éstas en la fase de germinación y plántula cuando la protección del cultivo es baja o nula Dicha rotación presentó valores de pérdidas de suelo por arriba de los niveles de tolerancia anuales propuestos por Mennering (1981) y Schertz (1993), recomendando implementar otras técnicas de conservación de suelo adicional a la práctica de cultivos en contornos para reducir las pérdidas de suelo.

Design and coupled-effect simulations of CMOS micro gas-sensors built on SOI thin membranes

This paper describes coupled-effect simulations of smart micro gas-sensors based on standard BiCMOS technology. The smart sensor features very low power consumption, high sensitivity and potential low fabrication cost achieved through full CMOS integration. For the first time the micro heaters are made of active CMOS elements (i.e. MOSFET transistors) and embedded in a thin SOI membrane consisting of Si and SiO2 thin layers. Micro gas-sensors such as chemoresistive, microcalorimeteric and Pd/polymer gate FET sensors can be made using this technology. Full numerical analyses including 3D electro-thermo-mechanical simulations, in particular stress and deflection studies on the SOI membranes are presented. The transducer circuit design and the post-CMOS fabrication process, which includes single sided back-etching, are also reported.

Design and simulations of SOI CMOS micro-hotplate gas sensors

This paper describes a new generation of integrated solid-state gas-sensors embedded in SOI micro-hotplates. The micro-hotplates lie on a SOI membrane and consist of MOSFET heaters that elevate the operating temperature, through self-heating, of a gas sensitive material. These sensors are fully compatible with SOI CMOS or BiCMOS technologies, offer ultra-low power consumption (under 100 mW), high sensitivity, low noise, low unit cost, reproducibility and reliability through the use of on-chip integration. In addition, the new integrated sensors offer a nearly uniform temperature distribution over the active area at its operating temperatures at up to about 300-350°C. This makes SOI-based gas-sensing devices particularly attractive for use in handheld battery-operated gas monitors. This paper reports on the design of a chemo-resistive gas sensor and proposes for the first time an intelligent SOI membrane microcalorimeter using active micro-FET heaters and temperature sensors. A comprehensive set of numerical and analogue simulations is also presented including complex 2D and 3D electro-thermal numerical analyses. © 2001 Elsevier Science B.V. All rights reserved.

Micro-Scale Gas Flows

了解微尺度气体流动特点是微机电系统设计和优化的基础.有关的研究可以上溯到20世纪初Knudsen的平面槽道流动质量流量的测量和Millikan的小球阻力系数的测量,实验结果揭示了稀薄气体效应即尺度效应对气体运动的重要影响.由于流动特征长度很小,微尺度气流经常处于滑流区甚至过渡领域,流动的相似参数为Knudsen数和Mach数.因此可以考虑利用相似准则,通过增大几何尺寸、减小压力的途径,解决微机电系统实验观测遇到的困难.为解决直接模拟MonteCarlo方法分析微机电系统中低速稀薄气流遇到的统计涨落困难,我们提出了信息保存法(IP),该方法能够有效克服统计散布,并已成功用于多种微尺度气流.