Optimization of the Mechanical and Optical Properties of Tunable Optical Sensor Arrays (TOSA) for a Nanospectrometer in the Visible and Near Infrared Spectral Range

Tunable Optical Sensor Arrays (TOSA) based on Fabry-Pérot (FP) filters, for high quality spectroscopic applications in the visible and near infrared spectral range are investigated within this work. The optical performance of the FP filters is improved by using ion beam sputtered niobium pentoxide (Nb2O5) and silicon dioxide (SiO2) Distributed Bragg Reflectors (DBRs) as mirrors. Due to their high refractive index contrast, only a few alternating pairs of Nb2O5 and SiO2 films can achieve DBRs with high reflectivity in a wide spectral range, while ion beam sputter deposition (IBSD) is utilized due to its ability to produce films with high optical purity. However, IBSD films are highly stressed; resulting in stress induced mirror curvature and suspension bending in the free standing filter suspensions of the MEMS (Micro-Electro-Mechanical Systems) FP filters. Stress induced mirror curvature results in filter transmission line degradation, while suspension bending results in high required filter tuning voltages. Moreover, stress induced suspension bending results in higher order mode filter operation which in turn degrades the optical resolution of the filter. Therefore, the deposition process is optimized to achieve both near zero absorption and low residual stress. High energy ion bombardment during film deposition is utilized to reduce the film density, and hence the film compressive stress. Utilizing this technique, the compressive stress of Nb2O5 is reduced by ~43%, while that for SiO2 is reduced by ~40%. Filters fabricated with stress reduced films show curvatures as low as 100 nm for 70 μm mirrors. To reduce the stress induced bending in the free standing filter suspensions, a stress optimized multi-layer suspension design is presented; with a tensile stressed metal sandwiched between two compressively stressed films. The stress in Physical Vapor Deposited (PVD) metals is therefore characterized for use as filter top-electrode and stress compensating layer. Surface micromachining is used to fabricate tunable FP filters in the visible spectral range using the above mentioned design. The upward bending of the suspensions is reduced from several micrometers to less than 100 nm and 250 nm for two different suspension layer combinations. Mechanical tuning of up to 188 nm is obtained by applying 40 V of actuation voltage. Alternatively, a filter line with transmission of 65.5%, Full Width at Half Maximum (FWHM) of 10.5 nm and a stopband of 170 nm (at an output wavelength of 594 nm) is achieved. Numerical model simulations are also performed to study the validity of the stress optimized suspension design for the near infrared spectral range, wherein membrane displacement and suspension deformation due to material residual stress is studied. Two bandpass filter designs based on quarter-wave and non-quarter-wave layers are presented as integral components of the TOSA. With a filter passband of 135 nm and a broad stopband of over 650 nm, high average filter transmission of 88% is achieved inside the passband, while maximum filter transmission of less than 1.6% outside the passband is achieved.

The Court of Justice of the European Union as a fundamental rights tribunal: challenges for the effective delivery of fundamental rights in the area of freedom, security and justice. CEPS Paper in Liberty and Security in Europe No. 49, 29 August 2012

This paper reflects on the challenges facing the effective implementation of the new EU fundamental rights architecture that emerged from the Lisbon Treaty. Particular attention is paid to the role of the Court of Justice of the European Union (CJEU) and its ability to function as a ‘fundamental rights tribunal’. The paper first analyses the praxis of the European Court of Human Rights in Strasbourg and its long-standing experience in overseeing the practical implementation of the European Convention for the Protection of Human Rights and Fundamental Freedoms. Against this analysis, it then examines the readiness of the CJEU to live up to its consolidated and strengthened mandate on fundamental rights as one of the prime guarantors of the effective implementation of the EU Charter of Fundamental Rights. We specifically review the role of ‘third-party interventions’ by non-governmental organisations, international and regional human rights actors as well as ‘interim relief measures’ when ensuring effective judicial protection of vulnerable individuals in cases of alleged violations of fundamental human rights. To flesh out our arguments, we rely on examples within the scope of the relatively new and complex domain of EU legislation, the Area of Freedom, Security and Justice (AFSJ), and its immigration, external border and asylum policies. In view of the fundamental rights-sensitive nature of these domains, which often encounter shifts of accountability and responsibility in their practical application, and the Lisbon Treaty’s expansion of the jurisdiction of the CJEU to interpret and review EU AFSJ legislation, this area can be seen as an excellent test case for the analyses at hand. The final section puts forth a set of policy suggestions that can assist the CJEU in the process of adjusting itself to the new fundamental rights context in a post-Lisbon Treaty setting.

Simulating metals and mine discharges in river basins using a new integrated catchment model for metals: pollution impacts and restoration strategies in the Aries-Mures river system in Transylvania, Romania

The INtegrated CAtchment (INCA) model has been developed to simulate the impact of mine discharges on river systems. The model accounts for the key kinetic chemical processes operating as well as the dilution, mixing and redistribution of pollutants in rivers downstream of mine discharges or acid rock drainage sites. The model is dynamic and simulates the day-to-day behaviour of hydrology and eight metals (cadmium, mercury, copper, zinc, lead, arsenic, manganese and chromium) as well as cyanide and ammonia. The model is semi-distributed and can simulate catchments, sub-catchment and in-stream river behaviour. The model has been applied to the Roia Montan Mine in Transylvania, Romania, and used to assess the impacts of old mine adits on the local catchments as well as on the downstream Aries and Mures river system. The question of mine restoration is investigated and a set of clean-up scenarios investigated. It is shown that the planned restoration will generate a much improved water quality from the mine and also alleviate the metal pollution of the river system.

Genotypic variations in the accumulation of Cd, Cu, Pb and Zn exhibited by six commonly grown vegetables

Metal contaminants in garden and allotment soils could possibly affect human health through a variety of pathways. This study focused on the potential pathway of consumption of vegetables grown on contaminated soil. Five cultivars each of six common vegetables were grown in a control and in a soil spiked with Cd, Cu, Pb and Zn. Highly significant differences in metal content were evident between cultivars of a number of vegetables for several of the contaminants. Carrot and pea cultivars exhibited significant differences in accumulated concentrations of Cd and Cu with carrot cultivars also exhibiting significant differences in Zn. Distinctive differences were also identified when comparing one vegetable to another, legumes (Leguminosae) tending to be low accumulators, root vegetables (Umbelliferae and Liliaceae) tending to be moderate accumulators and leafy vegetables (Compositae and Chenopodiaceae) being high accumulators. (c) 2006 Elsevier Ltd. All rights reserved.

A preliminary investigation into mining and smelting impacts on trace element concentrations in the soils and vegetation around Tharsis, SW Spain

Toxic trace elements present an environmental hazard in the vicinity of mining and smelting activities. However. the processes of transfer of these elements to groundwater and to plants are not always clear. Tharsis mine. in the Iberian pyrite belt (SW Spain), has been exploited since 2500 BC, with extensive smelting, taking place front the 1850S until the 1920s. Sixty four soil (mainly topsoils) and vegetation samples were collected in February 2001 and analysed by ICP-AES for 23 elements. Concentrations are 6-6300 mg kg(-1) As and 14-24800 mg kg(-1) Pb in soils, and 0.20-9 mg kg(-1) As and 2-195 mg Pb in vegetation. Trace element concentrations decrease rapidly away from the mine. with As and Pb concentrations in the range 6-1850 mg kg(-1) (median 22 mg kg(-1)) and 14-31 mg, kg(-1) (median 43 mg, kg(-1)), respectively, 1 km away from the mine. These concentrations are low when compared to other well-studied mining and smelting areas (e.g. 600 mg kg(-1) As at 8 km from Yellowknife smelter, Canada; >100 mg kg(-1) Pb over 270 km(2) around the Pb-Zn Port Pirie smelter. South Australia: mean of 1419 mg kg(-1) Pb around Aberystwyth smelter, Wales, UK). The high metal content of the vegetation and the low soil pH (mean pH 4.93) indicate the potential for trace element mobility which Could explain the relatively low concentration of metals in Tharsis topsoils and cause threats to plans to redevelop the Tharsis area as an orange plantation.

Interactions between earthworms and arsenic in the soil environment: a review

Chemical pollution of the environment has become a major source of concern. In particular, many studies have investigated the impact of pollution on biota in the environment. Studies on metalliferous contaminated mine spoil wastes have shown that some soil organisms have the capability to become resistant to metal/metalloid toxicity. Earthworms are known to inhabit arsenic-rich metalliferous soils and, due to their intimate contact with the soil, in both the solid and aqueous phases, are likely to accumulate contaminants present in mine spoil. Earthworms that inhabit metalliferous contaminated soils must have developed mechanisms of resistance to the toxins found in these soils. The mechanisms of resistance are not fully understood; they may involve physiological adaptation (acclimation) or be genetic. This review discusses the relationships between earthworms and arsenic-rich mine spoil wastes, looking critically at resistance and possible mechanisms of resistance, in relation to soil edaphic factors and possible trophic transfer routes. (C) 2003 Elsevier Science Ltd. All rights reserved.

Influence of adsorption geometry in the heterogeneous enantioselective catalytic hydrogenation of a prototypical enone

Asymmetric catalysis is of paramount importance in organic synthesis and, in current practice, is achieved by means of homogeneous catalysts. The ability to catalyze such reactions heterogeneously would have a major impact both in the research laboratory and in the production of fine chemicals and pharmaceuticals, yet heterogeneous asymmetric hydrogenation of C═C bonds remains hardly explored. Very recently, we demonstrated how chiral ligands that anchor robustly to the surface of Pd nanoparticles promote asymmetric catalytic hydrogenation: ligand rigidity and stereochemistry emerged as key factors. Here, we address a complementary question: how does the enone reactant adsorb on the metal surface, and what implications does this have for the enantiodifferentiating interaction with the surface-tethered chiral modifiers? A reaction model is proposed, which correctly predicts the identity of the enantiomer experimentally observed in excess.

Evolution of functional diversity in the cupin superfamily

The cupin superfamily of proteins is among the most functionally diverse of any described to date. It was named on the basis of the conserved beta-barrel fold ('cupa' is the Latin term for a small barrel), and comprises both enzymatic and non-enzymatic members, which have either one or two cupin domains. Within the conserved tertiary structure, the variety of biochemical function is provided by minor variation of the residues in the active site and the identity of the bound metal ion. This review discusses the advantages of this particular scaffold and provides an evolutionary analysis of 18 different subclasses within the cupin superfamily.

Modeling based on the structure of vicilins predicts a histidine cluster in the active site of oxalate oxidase

It is known that germin, which is a marker of the onset of growth in germinating wheat, is an oxalate oxidase, and also that germins possess sequence similarity with legumin and vicilin seed storage proteins. These two pieces of information have been combined in order to generate a 3D model of germin based on the structure of vicilin and to examine the model with regard to a potential oxalate oxidase active site. A cluster of three histidine residues has been located within the conserved beta-barrel structure. While there is a relatively low level of overall sequence similarity between the model and the vicilin structures, the conservation of amino acids important in maintaining the scaffold of the beta-barrel lends confidence to the juxtaposition of the histidine residues. The cluster is similar structurally to those found in copper amine oxidase and other proteins, leading to the suggestion that it defines a metal-binding location within the oxalate oxidase active site. It is also proposed that the structural elements involved in intermolecular interactions in vicilins may play a role in oligomer formation in germin/oxalate oxidase.

Segregated self-assembly and pillaring action of aliphatic dicarboxylic acids in the super structure of Cu-picolinate complexes

Three new supramolecular assemblies of co-crystallized metal complexes and aliphatic dicarboxylic acids, {[Cu(pic)(2)(H2O)(2)](H(2)mal)}(n) (1), {[Cu(pic)(2)(H2O)(2)](H(2)mal)(2)(H2O)(2)}(n) (2) and {[Cu(pic)(2)(MeOH)](H(2)succ)}(n) (3) {Hpic = 2-picolinic acid, H(2)mal = malonic acid and H(2)succ = succinic acid} have been synthesized and characterized by X-ray single-crystal structure determination. The crystal packings of the complexes reveal that supramolecular associations of the monomeric complex units lead to the formation of layers through hydrogen bonding. In all the complexes, the dicarboxylic acid units connect the 2-D layers to act as pillars. The interaction between water molecules and the dicarboxylic acid plays an important role in the overall supramolecular assembly. (C) 2008 Elsevier Ltd. All rights reserved.

Variation in the human Cannabinoid Receptor (CNR1) gene modulates gaze duration for happy faces

BACKGROUND: Humans from an early age look longer at preferred stimuli, and also typically look longer at facial expressions of emotion, particularly happy faces. Atypical gaze patterns towards social stimuli are common in Autism Spectrum Conditions (ASC). However, it is unknown if gaze fixation patterns have any genetic basis. In this study, we tested if variations in the cannabinoid receptor 1 (CNR1) gene are associated with gaze duration towards happy faces. This gene was selected because CNR1 is a key component of the endocannabinoid system, involved in processing reward, and in our previous fMRI study we found variations in CNR1 modulates the striatal response to happy (but not disgust) faces. The striatum is involved in guiding gaze to rewarding aspects of a visual scene. We aimed to validate and extend this result in another sample using a different technique (gaze tracking). METHODS: 30 volunteers (13 males, 17 females) from the general population observed dynamic emotion expressions on a screen while their eye movements were recorded. They were genotyped for the identical four SNPs in the CNR1 gene tested in our earlier fMRI study. RESULTS: Two SNPs (rs806377 and rs806380) were associated with differential gaze duration for happy (but not disgust) faces. Importantly, the allelic groups associated with greater striatal response to happy faces in the fMRI study were associated with longer gaze duration for happy faces. CONCLUSIONS: These results suggest CNR1 variations modulate striatal function that underlies the perception of signals of social reward such as happy faces. This suggests CNR1 is a key element in the molecular architecture of perception of certain basic emotions. This may have implications for understanding neurodevelopmental conditions marked by atypical eye contact and facial emotion processing, such as ASC.

House in the Shape of a Stretcher

In an essay from 1910 the architect and critic Adolf Loos distinguishes between buildings that are for everyday practical use and buildings made for contemplation. The latter type he asserts may be considered as both architecture and works of art. He refers to only two types of contemplative architecture namely the tomb and the monument. There are certain paintings made in the early part of the twentieth century that do not observe this separation such as certain works by Hopper and de Chirico. Here the commonplace is simultaneously experienced in the way a tomb might be. This mortifying gaze condemns building by inducing a sense that space has become inhospitable and alienating. It could be argued that these and other paintings made around this time such as Carlo Carra The Abandoned House 1916 are like premonitions of what will occur when building observes the prescription laid down by Loos and omit an aesthetic dimension. However it might also suggest that buildings need their tombs or at least some space that is not completely assimilable by the daily, practical and functional needs of an inhabitant.

Carolingian culture in the North Sea world: rethinking the cultural dynamics of personal adornment in Viking age England

Boosted by a proliferation in metal-detected finds, categories of personal adornment now constitute a vital archaeological source for interpreting Viking-age cultural interaction in the North Sea region. Previous research in England has explored the potential of this metalwork in relation to the formation of ‘Anglo-Scandinavian’ identity, but without due consideration of a wider spectrum of cultural influences. This article redresses the balance by shifting attention to twenty-eight belt fittings derived from richly embellished baldrics, equestrian equipment, and waist belts manufactured on the Frankish continent during the period of Carolingian hegemony in the later eighth and ninth centuries ad. The metalwork is classified and then contextualized in order to track import mechanisms and to assess the impact of Carolingian culture on the northern peripheries of the Frankish empire. The main conclusion is that the adoption, adaptation, and strategic manipulation of Carolingian/northern Frankish identity formed an embedded component of cultural dynamics in Viking-age England, scrutiny of which sheds new light on patterns of interconnectivity linking peoples of the North Sea world.