Heat Transfer in Plate Heat Exchangers

This study illustrates the different types of plate heat exchangers that are commonly used in various domestic and industrial applications. The main purpose of this paper was to devise a methodology that is capable of calculating optimum number of plates in the design of a plate heat exchanger. To obtain the appropriate number of plates, typically several iterations must be made before a final acceptable design is completed, since plate amount depends on many factors such as, flow velocities, physical properties of the streams, flow channel geometry, allowable pressure drop, plate dimensions, and the gap between the plates. The methodology presented here can be used as a general guide for designing a plate heat exchanger. To investigate the effects of relevant parameters on the thermal-hydraulic design of a plate heat exchanger, several experiments were carried out for single-phase and counter flow arrangement with two brazed plate heat exchangers by varying the flow rates and the inlet temperatures of the fluid streams. The actual heat transfer coefficients obtained based on the experiment were nearly close to the calculated values and to improve the design, a correction factor was introduced. Besides, the effect of flow channel velocity on the pressure drop inside the unit is presented.

Modern recovery boiler design criteria

Engineering and pricing of large recovery boiler were studied in this work. Engineering was carried out with Anita 4.2 which is an engineering program of Andritz. Key initial values were chosen with previous studies. Primary target of this work was to find out the consequences that furnace dimensions and furnace screen vertical part has to boiler pricing. Boilers that were engineered had different rate of furnace width and depth and different heat transfer plate count. Boiler balances were invariable. Boilers with different vertical screen construction were also calculated. First variation was boiler with vertical screen up to furnace roof. Other variation was to connect vertical screen to Pre-boiler generating bank inlet tubes. Total prices were calculated to engineered boilers. Pricing was sort out to heat transfers, high pressure pipes, steel structures, auxiliary equipments and civil/structural costs. This study did not notice parts of the boiler which costs do not vary with the construction of the boiler. Heat transfers had the largest share of costs. Boiler building had the most significant differences between the boilers. Furnace screen had also significant role especially to costs of the boiler building.

A monolithic glass chip for active single-cell sorting based on mechanical phenotyping

The mechanical properties of biological cells have long been considered as inherent markers of biological function and disease. However, the screening and active sorting of heterogeneous populations based on serial single-cell mechanical measurements has not been demonstrated. Here we present a novel monolithic glass chip for combined fluorescence detection and mechanical phenotyping using an optical stretcher. A new design and manufacturing process, involving the bonding of two asymmetrically etched glass plates, combines exact optical fiber alignment, low laser damage threshold and high imaging quality with the possibility of several microfluidic inlet and outlet channels. We show the utility of such a custombuilt optical stretcher glass chip by measuring and sorting single cells in a heterogeneous population based on their different mechanical properties and verify sorting accuracy by simultaneous fluorescence detection. This offers new possibilities of exact characterization and sorting of small populations based on rheological properties for biological and biomedical applications.

Sustainable Waste-to-Energy Production: Performance Evaluation of Distributed Generation fuelled by Landfill Gas

The environmental impact of landfill is a growing concern in waste management practices. Thus, assessing the effectiveness of the solutions implemented to alter the issue is of importance. The objectives of the study were to provide an insight of landfill advantages, and to consolidate landfill gas importance among others alternative fuels. Finally, a case study examining the performances of energy production from a land disposal at Ylivieska was carried out to ascertain the viability of waste to energy project. Both qualitative and quantitative methods were applied. The study was conducted in two parts; the first was the review of literatures focused on landfill gas developments. Specific considerations were the conception of mechanism governing the variability of gas production and the investigation of mathematical models often used in landfill gas modeling. Furthermore, the analysis of two main distributed generation technologies used to generate energy from landfill was carried out. The review of literature revealed a high influence of waste segregation and high level of moisture content for waste stabilization process. It was found that the enhancement in accuracy for forecasting gas rate generation can be done with both mathematical modeling and field test measurements. The result of the case study mainly indicated the close dependence of the power output with the landfill gas quality and the fuel inlet pressure.

Rapid and accurate hplc-dad method for the determination of the herbicide bispyribac-sodium in surface water, and its validation

A new method is described for the determination of the herbicide bispyribac-sodium in surface water, especially from river and irrigated rice water samples. The method involves extraction in solid phase and quantification by high performance liquid chromatography with diode array detection (HPLC-DAD). After optimization of the extraction and separation parameters, the method was validated. The method presented average recoveries of 101.3 and 97.7%, under repeatability and intermediate precision conditions, respectively, with adequate precision (RSD from 0.9 to 7.5%). The method was applied for the determination of bispyribac-sodium in surface water samples with a limit of detection of 0.1 μg L-1.

Aumento da resposta analítica por meio da otimização do sistema de injeção sem divisão de fluxo em cromatografia gasosa empregando a lei dos gases ideais

This paper reports the development of an easy, fast and effective procedure for the verification of the ideal gas law in splitless injection systems in order to improve the response. Results of a group of pesticides were used to demonstrate the suitability of the approach. The procedure helps establish experimental parameters through theoretical aspects. The improved instrumental response allowed extraction with lower sample volumes, the minimization of time and costs and the simplification of sample preparation.

Parâmetros cinéticos da degradação térmica de complexos entre percloratos de terras raras com lactama

Complexos de percloratos à base de terras raras com a 2-azaciclononanona (AZA) foram obtidos a partir da reação entre os respectivos sais hidratados com a AZA (proporção molar 1:8) pelo método de difusão de vapor e caracterizados por titulação complexiométrica com EDTA, microanálise (CHN), espectroscopia vibracional na região do IV, termogravimetria em atmosfera de ar e N2 e calorimetria exploratória diferencial (DSC) em atmosfera de N2. O estudo cinético desse trabalho foi realizado utilizando um software em QBASIC que faz a simulação dos dados termogravimétricos a partir de um conjunto dado de parâmetros cinéticos.

Numerical modelling of small supersonic axial flow turbines

Supersonic axial turbine stages typically exhibit lower efficiencies than subsonic axial turbine stages. One reason for the lower efficiency is the occurrence of shock waves. With higher pressure ratios the flow inside the turbine becomes relatively easily supersonic if there is only one turbine stage. Supersonic axial turbines can be designed in smaller physical size compared to subsonic axial turbines of same power. This makes them good candidates for turbochargers in large diesel engines, where space can be a limiting factor. Also the production costs are lower for a supersonic axial turbine stage than for two subsonic stages. Since supersonic axial turbines are typically low reaction turbines, they also create lower axial forces to be compensated with bearings compared to high reaction turbines. The effect of changing the stator-rotor axial gap in a small high (rotational) speed supersonic axial flow turbine is studied in design and off-design conditions. Also the effect of using pulsatile mass flow at the supersonic stator inlet is studied. Five axial gaps (axial space between stator and rotor) are modeled using threedimensional computational fluid dynamics at the design and three axial gaps at the off-design conditions. Numerical reliability is studied in three independent studies. An additional measurement is made with the design turbine geometry at intermediate off-design conditions and is used to increase the reliability of the modelling. All numerical modelling is made with the Navier-Stokes solver Finflo employing Chien’s k ¡ ² turbulence model. The modelling of the turbine at the design and off-design conditions shows that the total-to-static efficiency of the turbine decreases when the axial gap is increased in both design and off-design conditions. The efficiency drops almost linearily at the off-design conditions, whereas the efficiency drop accelerates with increasing axial gap at the design conditions. The modelling of the turbine stator with pulsatile inlet flow reveals that the mass flow pulsation amplitude is decreased at the stator throat. The stator efficiency and pressure ratio have sinusoidal shapes as a function of time. A hysteresis-like behaviour is detected for stator efficiency and pressure ratio as a function of inlet mass flow, over one pulse period. This behaviour arises from the pulsatile inlet flow. It is important to have the smallest possible axial gap in the studied turbine type in order to maximize the efficiency. The results for the whole turbine can also be applied to some extent in similar turbines operating for example in space rocket engines. The use of a supersonic stator in a pulsatile inlet flow is shown to be possible.

Pulsatile Blood Flow Simulations in Computed Tomography(CT) Scan-Based and Idealized Geometries of Human Aorta

Blood flow in human aorta is an unsteady and complex phenomenon. The complex patterns are related to the geometrical features like curvature, bends, and branching and pulsatile nature of flow from left ventricle of heart. The aim of this work was to understand the effect of aorta geometry on the flow dynamics. To achieve this, 3D realistic and idealized models of descending aorta were reconstructed from Computed Tomography (CT) images of a female patient. The geometries were reconstructed using medical image processing code. The blood flow in aorta was assumed to be laminar and incompressible and the blood was assumed to be Newtonian fluid. A time dependent pulsatile and parabolic boundary condition was deployed at inlet. Steady and unsteady blood flow simulations were performed in real and idealized geometries of descending aorta using a Finite Volume Method (FVM) code. Analysis of Wall Shear Stress (WSS) distribution, pressure distribution, and axial velocity profiles were carried out in both geometries at steady and unsteady state conditions. The results obtained in thesis work reveal that the idealization of geometry underestimates the values of WSS especially near the region with sudden change of diameter. However, the resultant pressure and velocity in idealized geometry are close to those in real geometry

Distribution and role of macrophytes in coastal lagoons : implications of critical shifts

Crossroads, crucibles and refuges are three words that may describe natural coastal lagoon environments. The words refer to the complex mix of marine and terrestrial influences, prolonged dilution due to the semi-enclosed nature and the function of a habitat for highly diverse plant and animal communities, some of which are endangered. To attain a realistic picture of the present situation, high vulnerability to anthropogenic impact should be added to the description. As the sea floor in coastal lagoons is usually entirely photic, macrophyte primary production is accentuated compared with open sea environments. There is, however, a lack of proper knowledge on the importance of vegetation for the general functioning of coastal lagoon ecosystems. The aim of this thesis is to assess the role of macrophyte diversity, cover and species identity over temporal and spatial scales for lagoon functions, and to determine which steering factors primarily restrict the qualitative and quantitative composition of vegetation in coastal lagoons. The results are linked to patterns of related trophic levels and the indicative potential of vegetation for assessment of general conditions in coastal lagoons is evaluated. This thesis includes five field studies conducted in flads and glo-flads in the brackish water northern Baltic Sea. Flads and glo-flads are defined as a Baltic variety of coastal lagoons, which due to an inlet threshold and post-glacial landuplift slowly will be isolated from the open sea. This process shrinks inlet size, increases exposure and water retention, and is called habitat isolation. The studied coastal lagoons are situated in the archipelago areas of the eastern coast of Sweden, the Åland Islands and the south-west mainland of Finland, where land-uplift amounts to ca. 5 mm/ per year. Out of 400 evaluated sites, a total of 70 lagoons varying in inlet size, archipelago position and anthropogenic influence to cover for essential environmental variation were chosen for further inventory. Vegetation composition, cover and richness were measured together with several hydrographic and morphometric variables in the lagoons both seasonally and inter-annually to cover for general regional, local and temporal patterns influencing lagoon and vegetation development. On smaller species-level scale, the effects of macrophyte species identity and richness for the fish habitat function were studied by examining the influence of plant interaction on juvenile fish diversity. Thus, the active election of plant monoand polycultures by fish and the diversity of fish in the respective culture were examined and related to plant height and water depth. The lagoons and vegetation composition were found to experience a regime shift initiated by increased habitat isolation along with land-uplift. Vegetation composition altered, richness decreased and cover increased forming a less isolated and more isolated regime, named the vascular plant regime and charophyte regime, respectively according to the dominant vegetation. As total phosphorus in the water, turbidity and the impact of regional influences decreased in parallel, the dominance of charophytes and increasing cover seemed to buffer and stabilize conditions in the charophyte regime and indicated an increased functional role of vegetation for the lagoon ecosystem. The regime pattern was unaffected by geographical differences, while strong anthropogenic impact seemed to distort the pattern due to loss of especially Chara tomentosa L. in the charophyte regime. The regimes were further found unperturbed by short-time temporal fluctuations. In fact the seasonal and inter-annual dynamics reinforced the functional difference between the regimes by the increasing role of vegetation along habitat isolation and the resemblance to lake environments for the charophyte regime. For instance, greater total phosphorus and chlorophyll a concentrations in the water in the beginning of the season in the charophyte regime compared with the vascular plant regime presented a steeper reduction to even lower values than in the vascular plant regime along the season. Despite a regional importance and positive relationship of macrophyte diversity in relation to trophic diversity, species identity was underlined in the results of this thesis, especially with decreasing spatial scale. This result was supported partly by the increased role of charophytes in the functioning of the charophyte regime, but even more explicitly by the species-specific preference of juvenile fish for tall macrophyte monocultures. On a smaller species-level scale, tall plant species in monoculture seemed to be able to increase their length, indicating that negative selection forms preferred habitat structures, which increase fish diversity. This negative relationship between plant and fish diversity suggest a shift in diversity patterns among trohic levels on smaller scale. Thus, as diversity patterns seem complex and diverge among spatial scales, it might be ambiguous to extend the understanding of diversity relationships from one trophic level to the other. All together, the regime shift described here presents similarities to the regime development in marine lagoon environments and shallow lakes subjected to nutrient enrichment. However, due to nutrient buffering by vegetation with increased isolation and water retention as a consequence of the inlet threshold, the development seems opposite to the course along an eutrophication gradient described in marine lagoons lacking an inlet threshold, where the role of vegetation decreases. Thus, the results imply devastating consequences of inlet dredging (decreasing isolation) in terms of vegetation loss and nutrient release, and call for increased conservational supervision. Especially the red listed charophytes would suffer negatively from such interference and the consequences are likely to also deteriorate juvenile fish production. The fact that a new species to Finland, Chara connivens Salzm. Ex. Braun 1835 was discovered during this study further indicates a potential of the lagoons serving as refuges for rare species.

SMB-laitteiston suunnittelu hydrometallurgisiin sovelluksiin

Työn tarkoituksena oli suunnitella, ohjelmoida ja koekäyttää SMB-laitteisto (Simulated Moving Bed) hydrometallurgisiin erotuksiin. Simuloitu liikkuvapeti saadaan aikaan vaihtamalla sisään- ja ulostuloporttien paikkaa nestevirran suuntaan. Tällöin aikaansaadaan kiintoaineen vastavirtaus minkä johdosta erotustehokkuus kasvaa. Komponenttien retentiotaipumuseroista johtuen komponentit liikkuvat eri nopeuksilla kolonnijärjestelmässä. Enemmän pidättäytyvät komponentit liikkuvat nestevirtaa vastaan ja vähemmän pidättäytyvät komponentit nestevirran mukana. Hydrometallurgiassa vastavirtauksen käyttöä ei ole tieteellisissä julkaisuissa käsitelty laajalti ja saatavilla oleva informaatio onkin kaupallisten yritysten tuottamaa. Hydrometallurgiassa vastavirtausta käyttävissä ioninvaihtolaitteistoissa hyödynnetään irrallisia regenerointivyöhykkeitä. Venttiilijärjestelmän osalta päädyttiin ratkaisuun jossa käytetään yhtä kiertoventtiiliä kullekin virralle, minkä lisäksi kolonnien väleillä käytetään solenoidiventtiiliä. Tämä järjestelmä mahdollistaa yleisimpien SMB-menetelmien käytön mukaan lukien irralliset vyöhykkeet. Laitteiston ohjauksesta vastaa LabVIEW 2010:llä ohjelmoitu ohjelmisto, joka sisältää kaikkien tarvittavien laitteiden ohjausrutiinit. Se mahdollistaa venttiilien synkroniset ja epäsynkroniset vaihdot. Laitteiston puhdistusta varten on ohjelmistoon rakennettu oma rutiini venttiilejä varten. Pumppujen osalta ohjelmisto mahdollistaa vakiovirtauksen sekä lineaaristen ja porrasmuotoisten gradienttien käytön. Ongelmatilanteita varten ohjelmisto valvoo pumppujen ja venttiilien toimintaa ja pysäyttää laitteiston tarvittaessa. Koekäytön avulla pystyttiin todentamaan laitteiston toimivuus.

Application of Computational Fluid Dynamics in Modeling Blood Flow in Human Thoracic Aorta

The aim of this study was to simulate blood flow in thoracic human aorta and understand the role of flow dynamics in the initialization and localization of atherosclerotic plaque in human thoracic aorta. The blood flow dynamics in idealized and realistic models of human thoracic aorta were numerically simulated in three idealized and two realistic thoracic aorta models. The idealized models of thoracic aorta were reconstructed with measurements available from literature, and the realistic models of thoracic aorta were constructed by image processing Computed Tomographic (CT) images. The CT images were made available by South Karelia Central Hospital in Lappeenranta. The reconstruction of thoracic aorta consisted of operations, such as contrast adjustment, image segmentations, and 3D surface rendering. Additional design operations were performed to make the aorta model compatible for the numerical method based computer code. The image processing and design operations were performed with specialized medical image processing software. Pulsatile pressure and velocity boundary conditions were deployed as inlet boundary conditions. The blood flow was assumed homogeneous and incompressible. The blood was assumed to be a Newtonian fluid. The simulations with idealized models of thoracic aorta were carried out with Finite Element Method based computer code, while the simulations with realistic models of thoracic aorta were carried out with Finite Volume Method based computer code. Simulations were carried out for four cardiac cycles. The distribution of flow, pressure and Wall Shear Stress (WSS) observed during the fourth cardiac cycle were extensively analyzed. The aim of carrying out the simulations with idealized model was to get an estimate of flow dynamics in a realistic aorta model. The motive behind the choice of three aorta models with distinct features was to understand the dependence of flow dynamics on aorta anatomy. Highly disturbed and nonuniform distribution of velocity and WSS was observed in aortic arch, near brachiocephalic, left common artery, and left subclavian artery. On the other hand, the WSS profiles at the roots of branches show significant differences with geometry variation of aorta and branches. The comparison of instantaneous WSS profiles revealed that the model with straight branching arteries had relatively lower WSS compared to that in the aorta model with curved branches. In addition to this, significant differences were observed in the spatial and temporal profiles of WSS, flow, and pressure. The study with idealized model was extended to study blood flow in thoracic aorta under the effects of hypertension and hypotension. One of the idealized aorta models was modified along with the boundary conditions to mimic the thoracic aorta under the effects of hypertension and hypotension. The results of simulations with realistic models extracted from CT scans demonstrated more realistic flow dynamics than that in the idealized models. During systole, the velocity in ascending aorta was skewed towards the outer wall of aortic arch. The flow develops secondary flow patterns as it moves downstream towards aortic arch. Unlike idealized models, the distribution of flow was nonplanar and heavily guided by the artery anatomy. Flow cavitation was observed in the aorta model which was imaged giving longer branches. This could not be properly observed in the model with imaging containing a shorter length for aortic branches. The flow circulation was also observed in the inner wall of the aortic arch. However, during the diastole, the flow profiles were almost flat and regular due the acceleration of flow at the inlet. The flow profiles were weakly turbulent during the flow reversal. The complex flow patterns caused a non-uniform distribution of WSS. High WSS was distributed at the junction of branches and aortic arch. Low WSS was distributed at the proximal part of the junction, while intermedium WSS was distributed in the distal part of the junction. The pulsatile nature of the inflow caused oscillating WSS at the branch entry region and inner curvature of aortic arch. Based on the WSS distribution in the realistic model, one of the aorta models was altered to induce artificial atherosclerotic plaque at the branch entry region and inner curvature of aortic arch. Atherosclerotic plaque causing 50% blockage of lumen was introduced in brachiocephalic artery, common carotid artery, left subclavian artery, and aortic arch. The aim of this part of the study was first to study the effect of stenosis on flow and WSS distribution, understand the effect of shape of atherosclerotic plaque on flow and WSS distribution, and finally to investigate the effect of lumen blockage severity on flow and WSS distributions. The results revealed that the distribution of WSS is significantly affected by plaque with mere 50% stenosis. The asymmetric shape of stenosis causes higher WSS in branching arteries than in the cases with symmetric plaque. The flow dynamics within thoracic aorta models has been extensively studied and reported here. The effects of pressure and arterial anatomy on the flow dynamic were investigated. The distribution of complex flow and WSS is correlated with the localization of atherosclerosis. With the available results we can conclude that the thoracic aorta, with complex anatomy is the most vulnerable artery for the localization and development of atherosclerosis. The flow dynamics and arterial anatomy play a role in the localization of atherosclerosis. The patient specific image based models can be used to diagnose the locations in the aorta vulnerable to the development of arterial diseases such as atherosclerosis.

Solar energy use for water pre-heating in boilers of agro-industries

Energy consumption in the world has been growing every year. The industrial sector represents 27.32% of the world energy demand. Heating systems that use solar energy may contribute with a percentage of the total energy required by industries. This work aimed to study the use of vacuum solar collectors for water pre-heating in boilers. We used four collectors installed according to NBR 15,569; water flow through the tubes was 0.058 L/s, and temperature in the inlet and outlet pipes was measured. Results showed that instantaneous radiation, and inlet fluid and room temperatures are variables that influence the process, reaching water maximum temperature in the solar collector outlet of 97.9 °C, and efficiency of approximately 65% for most experiments. For the financial viability evaluation, the payback study was applied, which resulted in 4; 7 and 5 years, for the respective sources: firewood, LPG (liquefied petroleum gas), and electricity. Regarding the calculation of the annual contribution to the reduction of greenhouse gases, it was, respectively, 2.162 and 356 kg of CO2 per m² of collector tubes, in comparison with firewood and LPG.

Microencapsulation of pequi pulp by spray drying: use of modified starches as encapsulating agent

The aim of this study was to evaluate the microencapsulation of pequi pulp by spray drying. A central composite rotational design was used in order to evaluate the effect of the independent variables: inlet air temperature, surfactant concentration and modified starch concentration. The dependent variables were assumed as yield of the process and the product features microencapsulated. A selection of the best process condition was performed to obtain the best condition of a product with the highest vitamin C and carotenoids content. Powders showed moisture content below 2%. The experimental values of hygroscopicity, yield, water activity, total carotenoids and vitamin C powders ranged from 7.96 to 10.67 g of adsorbed water/100g of solids, 24.34 to 49.80%, 0.13 to 0.30, 145.78 to 292.11 mg of ascorbic acid/g of pequi solids and 15.51 to 123.42 mg of carotenoids/g of pequi solids, respectively. The inlet air temperature 140°C, the surfactant concentration of 2.5% and the modified starch concentration of 22.5% was recommended as the selected condition. By the scanning electron microscopy, it was observed that most of the particles had spherical shape and smooth surface.

Backpressure effects on the flow-pressure relation of driplines

ABSTRACT For drip irrigation design and management, it is necessary to know the relation between flow and pressure acting on emitters. In the case of subsurface drip irrigation, the backpressure phenomenon may change the hydraulic characteristics of emitters. Thus, this study aimed at determining such relationship between flow and pressure of different driplines in surface and subsurface conditions; aiming to find possible differences in hydraulic behavior. We tested four emitter types; two pressure compensating (D5000 and Hydro PCND) and two non-pressure compensating (TalDrip and Jardiline). Emitter flow rates were attained in atmospheric conditions and submerged in water, in which submergence levels represented backpressure. Assays were performed using inlet pressures of 80, 100, 120, and 150 kPa for the Hydro PCND dripline and 25, 50, 100, and 150 kPa for the other ones; the backpressures were of 0.49, 1.47, 2.45, 4.41 and 6.37 kPa with four replications. The emitters had their proportionality constants and discharge exponents changed in submerged applications, representing backpressure effect. Non-pressure compensating emitters had their discharge exponent decreased, while in pressure compensating ones, it was increased. Backpressure reduced emitter flow rates at all evaluated pressures.