THE MISCIBILITY AND MORPHOLOGY OF EPOXY-RESIN POLY(ETHYLENE OXIDE) BLENDS

Poly(ethylene oxide) (PEO) was found to be miscible with uncured epoxy resin, diglycidyl ether of bisphenol A (DGEBA), as shown by the existence of a single glass transition temperature (T(g)) in each blend. However, PEO with M(n) = 20 000 was judged to be immiscible with the highly amine-crosslinked epoxy resin (ER). The miscibility and morphology of the ER/PEO blends was remarkably affected by crosslinking. It was observed that phase separation in the ER/PEO blends occurred as the crosslinking progressed. This is considered to be due to the dramatic change in the chemical and physical nature of ER during the crosslinking.

BLENDS OF PHENOLPHTHALEIN POLY(ETHER ETHER KETONE) WITH PHENOXY AND EPOXY-RESIN

The properties of miscible phenolphthalein poly(ether ether ketone)/phenoxy (PEK-C/phenoxy) blends have been measured by dynamic mechanical analysis and tensile testing. The blends were found to have single glass transition temperatures (T(g)) that vary continuously with composition. The tensile moduli exhibit positive deviations from simple additivity. Marked positive deviations were also observed for tensile strength. The tensile strengths of the 90/10 and 75/25 PEK-C/phenoxy blends are higher than those of both the pure components. Embrittlement, or transition from the brittle to the ductile mode of failure, occurs in the composition range of 50-25 wt% PEK-C. These observations suggest that mixing on the segmental level has occurred and that there is enough interaction between the components to decrease its internal mobility significantly. PEK-C was also found to be miscible with the epoxy monomer, diglycidyl ether of bisphenol A (DGEBA), as shown by the existence of a single glass transition temperature (T(g)) within the whole composition range. Miscibility between PEK-C and DGEBA could be considered to be due mainly to entropy. However, PEK-C was judged to be immiscible with the diaminodiphenylmethane-curved epoxy resin (DDM-cured ER). It was observed that the PEK-C/ER blends have two T(g), which remain invariant with composition and are almost the same as those of the pure components, respectively. Scanning electron microscopy showed that the PEK-C/ER blends have a two-phase structure. The different miscibility with PEK-C between DGEBA and the DDM-cured ER is considered to be due to the dramatic change in the chemical and physical nature of ER after curing.

COMPATIBILIZING EFFECT OF POLY(ETHYLENE OXIDE)-B-POLYSTYRENE-B-POLY(ETHYLENE OXIDE) IN PHENOLPHTHALEIN POLY(ETHER ETHER KETONE) POLY(2,6-DIMETHYL-1,4-PHENYLENE OXIDE) BLENDS

The morphology and mechanical behaviour of phenolphthalein poly(ether ether ketone) (PEK-C)/poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) blends has been investigated. A poly(ethylene oxide)-b-polystyrene-b-poly(ethylene oxide) (PEO-PS-PEO) triblock copolymer was used as compatibilizer. It was found that PEO-PS-PEO has a compatibilizing effect on the PEK-C/PPO blends. The addition of PEO-PS-PEO to the blends greatly improves phase dispersion and interfacial interfacial adhesion and also enhances the ultimate tensile strength and Young's modulus at compositions ranging from 30 to 70% PEK-C. However, all the values of the ultimate tensile strength within the whole composition range are lower than those expected by simple additivity, probably owing to the poor mechanical properties of PEO-PS-PEO copolymer.

HDPE,LLDPE或LDPE高取向薄膜微结构的电子显微学研究

木工作用透射电子显微术及电子衍射技术研究3种PE(HDPE,LLDPE或LDPE)均聚物高取向薄膜的微结构。定量测定了它们的结晶尺寸。通过倾斜样品电子显微学研究确定了不同种PE纤维结构的对称性。

LLDPE耐老化易回收地膜的研制

研究了不同结构受阻胺光稳定剂及其与其它光稳定剂并用条件下对PE的稳定效能,从而研制出耐大气老化性能优异的LLDPE地膜。此地膜经一个农业生产季节覆盖应用后,拉伸强度和断裂伸长率均保留85%左右,人工从田间清理出的废膜长约2m,无小块碎膜残留;并观测到地膜厚度对废膜回收也有贡献,为解决普通地膜的残膜难于从农田中回收带来的严重污染问题提供了一条技术途径。

HDPE/LLDPE共混物高取向薄膜微结构电子显微学研究

本工作用透射电镜(TEM)、电子衍射和示差扫描量热计(DSC)等方法研究高密度聚乙烯(HDPE)和线性低密度聚乙烯(LLDPE)共混物高取向薄膜的微结构。结果表明熔体拉伸HDPE/LLDPE共混物薄膜含有高取向片晶结构。随着共混物中LLDPE含量的增加,片晶的尺寸相应减小。当LLDPE含量超过50％时,结晶结构从纯HDPE的非对称性纤维结构变为对称性纤维结构。高取向共混物在全组成范围成内形成共结晶。