High productivity and upwelling in the California Current during Oxygen-Isotope Stage 3: diatom evidence

Evidence for vigorous coastal upwelling and enhanced diatom productivity during the latter part of Oxygen-Isotope Stage 3 (OIS-3) is suggested by changes in diatom assemblages in laminated sediment from the northern California margin and in bioturbated and laminated sediment from Santa Barbara Basin. These conditions require strong along-shore or off-shore wind stress off California preceding the onset of global glacial conditions.

Oxygen isotope analysis of corals from the Gulf of California and the Gulf of Panama: application and implications for coral-based paleoclimate reconstructions [abstract]

EXTRACT (SEE PDF FOR FULL ABSTRACT): Coral-based reconstruction of past variability of sea surface conditions is improving our understanding of the tropical ocean-atmosphere system. We present oxygen isotope records from corals collected near the tip of Baja California (Baja) and the Gulf of Panama (Saboga).

Influence of the state of the inlet endwall boundary layer on the interaction between pressure surface separation and endwall flows

This paper describes the effect of the state of the inlet boundary layer (laminar or turbulent) on the structure of the endwall flow on two different profiles of low-pressure (LP) turbine blades (solid thin and hollow thick). At present the state of the endwall boundary layer at the inlet of a real LP turbine is not known. The intention of this paper is to show that, for different designs of LP turbine, the state of the inlet boundary layer affects the performance of the blade in very different ways. The testing was completed at low speed in a linear cascade using area traversing, flow visualization and static pressure measurements. The paper shows that, for a laminar inlet boundary layer, the two profiles have a similar loss distribution and structure of endwall flow. However, for a turbulent inlet boundary layer the two profiles are shown to differ significantly in both the total loss and endwall flow structure. The pressure side separation bubble on the solid thin profile is shown to interact with the passage vortex, causing a higher endwall loss than that measured on the hollow thick profile.

The effect of wake passing on a flow separation in a low pressure turbine cascade

This paper describes an investigation into the effect that passing wakes have on a separation bubble that exists on the pressure surface and near the leading edge of a low pressure turbine blade. Previous experimental studies have shown that the behaviour of this separation is strongly incidence dependent and that it responds to its disturbance environment. The results presented in this paper examine the effect of wake passing in greater detail. Two dimensional, Reynolds averaged, numerical predictions are first used to examine qualitatively the unsteady interaction between the wakes and the separation bubble. The separation is predicted to consist of spanwise vortices whose development is in phase with the wake passing. However, comparison with experiments shows that the numerical predictions exaggerate the coherence of these vortices and also overpredict the time-averaged length of the separation. Nonetheless, experiments strongly suggest that the predicted phase locking of the vortices in the separation onto the wake passing is physical.

The effect of boundary layer trips on intake separation in crosswinds

The flow typical of that occurring over the windward lip of an aero engine intake operating in a crosswind has been reproduced on a 2D lip. The uncontrolled boundary layer undergoes a laminar separation at the leading edge of the lip. It has been shown that a minimum size of boundary layer trip, positioned upstream of the separation location, is required to enable the flow to remain attached around the leading edge. A turbulent separation then occurs in the diffuser. Larger diameter trips promote earlier diffuser separation. Copyright © 2008 by the American Institute of Aeronautics and Astronautics, Inc.

Species identification of family Lutjanidae and separation of populations of John’s snapper (Lutjanus johnii) in Persian Gulf and Oman Sea based on otolith shape analysis

The anatomical and morphometric (shape indices, contour descriptors and otolith weight) characterizations of sagittal otoliths were investigated in 13 species of Lutjanus spp. inhabiting the Persian Gulf. This is the first study that compares the efficiency of three different image analysis techniques for discriminating species based on the shape of the outer otolith contour, including elliptical Fourier descriptors (EFD), fast Fourier transform (FFT) and wavelet transform (WT). Sagittal otoliths of snappers are morphologically similar with some small specific variations. The use of otolith contour based on wavelets (WT) provided the best results in comparison with the two other methods based on Fourier descriptors, but only the combination of the all three methods (EFD, FFT and WT) was useful to obtain a robust classification of species. The species prediction improved when otolith weight was included. In relation to the shape indices, only the aspect ratio provided a clear grouping of species. Also, another study was carried on to test the possibility of application of shape analysis and comparing otolith contour of otoliths of Lutjanus johnii from Persian Gulf and Oman Sea to identify potential stocks. The results showed the otoliths have differences in contour shape and can be contribute to two different stocks.

Unsteady Effects of Shock Wave Induced Separation

The aim of this series is to publish promptly and in detailed form new material from the field of Numerical Fluid Mechanics and Multidisciplinary Design ...