Seawater conditions during the experiment in May 2011 at the sampling sites off Vulcano Island

The impacts of ocean acidification on coastal biofilms are poorly understood. Carbon dioxide vent areas provide an opportunity to make predictions about the impacts of ocean acidification. We compared biofilms that colonised glass slides in areas exposed to ambient and elevated levels of pCO2 along a coastal pH gradient, with biofilms grown at ambient and reduced light levels. Biofilm production was highest under ambient light levels, but under both light regimes biofilm production was enhanced in seawater with high pCO2. Uronic acids are a component of biofilms and increased significantly with high pCO2. Bacteria and Eukarya denaturing gradient gel electrophoresis profile analysis showed clear differences in the structures of ambient and reduced light biofilm communities, and biofilms grown at high pCO2 compared with ambient conditions. This study characterises biofilm response to natural seabed CO2 seeps and provides a baseline understanding of how coastal ecosystems may respond to increased pCO2 levels.

Continuous measurements at Schwingbachtal Studienlandschaft in the growing seasons 2013-2014

The recent development of in-situ monitoring devices, such as UV-spectrometers, makes the study of short-term stream chemistry variation relevant, especially the study of diurnal cycles, which are not yet fully understood. Our study is based on high-frequency data from an agricultural catchment (Studienlandschaft Schwingbachtal, Germany). We propose a novel approach, i.e. the combination of cluster analysis and Linear Discriminant Analysis, to mine from these data nitrate behavior patterns. As a result, we observe a seasonality of nitrate diurnal cycles, that differs from the most common cycle seasonality described in the literature, i.e. pre-dawn peaks in spring. Our cycles appear in summer and the maximum and minimum shift to a later time in late summer/autumn. This is observed both for water- and energy-limited years, thus potentially stressing the role of evapotranspiration. This concluding hypothesis on the role of evapotranspiration on nitrate stream concentration, which was obtained through data mining, broadens the perspective on the diurnal cycling of stream nitrate concentrations.

Interindustrial Structure in the Asia-Pacific Region: Growth and Integration, by Using 2000 AIO Table

Over the past 20 years Asian countries have achieved a certain degree of economic growth and at the same time deepened spatial interdependence. In January 2006, IDE completed the 2000 Asian International Input-Output Table, which covers eight major East Asian countries/regions as well as Japan and the United States. Given the dynamic changes in the economies of East Asia, this paper attempts to summarize the characteristics and their patterns of change in industrial structures and trade structures of the countries/regions in the Asia-Pacific region from the three viewpoints of time, space, and industry, by using the AIO table for 1985, 1990, 1995, and 2000.

Preface : (Boundary Element Method) Computers and Structures 83 (2005)

The Boundary Element Method is a powerful numerical technique well rooted in everyday engineering practice. This is shown by boundary element methods included in the most important commercial computer packages and in the continuous publication of books composed to explain the features of the method to beginners or practicing engineers. Our first paper in Computers & Structures on Boundary Elements was published in 1979 (C & S 10, pp. 351–362), so this Special Issue is for us not only the accomplishment of our obligation to show other colleagues the possibilities of a numerical technique in which we believe, but also the celebration of our particular silver jubilee with this Journal.

Recommendations on seismic actions on port structures

The paper describes the main features of a Technical Recommendation first draft on Seismic Action on port structures promoted recently by the Spanish Ministry of Public Works (MOPT). Although much more research is needed to clarify the seismic behaviour of the vast class of problems present in port structures the current state of the art allows at least a classification of subjects and the establishment of minimum requirements to guide the design. Also the use of more refined methods for specially dangerous situations needs some general guidelines that contribute to mantein the design under reasonable safety margins. The Recommendations of the Spanish MOPT are a first try in those directions.

Expert systems for quality prediction in structural engineering

This work deals with quality level prediction in concrete structures through the helpful assistance of an expert system wich is able to apply reasoning to this field of structural engineering. Evidences, hypotheses and factors related to this human knowledge field have been codified into a Knowledge Base in terms of probabilities for the presence of either hypotheses or evidences,and conditional presence of both. Human experts in structural engineering and safety of structures gave their invaluable knowledge and assistance necessary when constructing the "computer knowledge body".

River Restoration in Spain: Theoretical and Practical Approach in the Context of the European Water Framework Directive.

River restoration is becoming a priority in many countries because of increasing the awareness of environmental degradation. In Europe, the EU Water Framework Directive (WFD) has significantly reinforced river restoration, encouraging the improvement of ecological status for water bodies. To fulfill the WFD requirements, the Spanish Ministry of the Environment developed in 2006 a National Strategy for River Restoration whose design and implementation are described in this paper. At the same time many restoration projects have been conducted, and sixty of them have been evaluated in terms of stated objectives and pressures and implemented restoration measures. Riparian vegetation enhancement, weir removal and fish passes were the most frequently implemented restoration measures, although the greatest pressures came from hydrologic alteration caused by flow regulation for irrigation purposes. Water deficits in quantity and quality associated with uncontrolled water demands seriously affect Mediterranean rivers and represent the main constraint to achieving good ecological status of Spanish rivers, most of them intensively regulated. Proper environmental allocation of in-stream flows would need deep restrictions in agricultural water use which seem to be of very difficult social acceptance. This situation highlights the need to integrate land-use and rural development policies with water resources and river management, and identifies additional difficulties in achieving the WFD objectives and good ecological status of rivers in Mediterranean countries.

Grain size gradient length scale in ballistic properties optimization of functionally graded nanocrystalline steel plates

The last few years have highlighted the existence of two relevant length scales in the quest to ultrahigh-strength polycrystalline metals. Whereas the microstructural length scale – e.g. grain or twin size – has mainly be linked to the well-established Hall–Petch relationship, the sample length scale – e.g. nanopillar size – has also proven to be at least as relevant, especially in microscale structures. In this letter, a series of ballistic tests on functionally graded nanocrystalline plates are used as a basis for the justification of a “grain size gradient length scale” as an additional ballistic properties optimization parameter.

A contribution to the optimal numbering of tree structures

This paper develops an automatic procedure for the optimal numbering of members and nodes in tree structures. With it the stiffness matrix is optimally conditioned either if a direct solution algorithm or a frontal one is used to solve the system of equations. In spite of its effectiveness, the procedure is strikingly simple and so is the computer program shown below.

Model of human rhythmic activities on structures

Crowd induced dynamic loading in large structures, such as gymnasiums or stadiums, is usually modelled as a series of harmonic loads which are defined in terms of their Fourier coefficients. Different values of these Fourier coefficients that were obtained from full scale measurements can be found in codes. Recently, an alternative has been proposed, based on random generation of load time histories that take into account phase lags among individuals inside the crowd. Generally the testing is performed on platforms or structures that can be considered rigid because their natural frequencies are higher than the excitation frequencies associated with crowd loading. In this paper we shall present the testing done on a structure designed to be a gymnasium, which has natural frequencies within that range. In this test the gym slab was instrumented with acceleration sensors and different people jumped on a force plate installed on the floor. Test results have been compared with predictions based on the two abovementioned load modelling alternatives and a new methodology for modelling jumping loads has been proposed in order to reduce the difference between experimental and numerical results at high frequency range.

Influence of crowds in the dynamic characteristics of a structure

The interest for modelling of human actions acting on structures has been recurrent since the first accidents on suspension bridges in the nineteenth century like Broughton (1831) in the U.K. or Angers (1850) in France. Stadiums, gymnasiums are other type of structure where the human induced vibration is very important. In these structures appear particular phenomenon like the interaction person-structure (lock-in), the person-person synchronization, and the influence of the mass and damping of the people in the structure behaviour. This work focuses on the latter topic. The dynamic characteristic of a structure can be changed due to the presence of people on it. In order to evaluate these property modifications several testing have been carried out on a structure designed to be a gymnasium. For the test an electro-dynamic shaker was installed in a fixed point of the gym slab and different groups of people were located around the shaker. In each test the number of people was changed and also their posture (standing and sitting). Test data were analyzed and processed to verify modifications in the structure behaviour.

Modifications in the Dynamic Properties of a Structure due to Human Actions

The interest for modelling of human actions acting on structures has been recurrent since the first accidents on suspension bridges in the nineteenth century such as Broughton (1831) in the U.K. or Angers (1850) in France. Stadiums, gymnasiums are other types of structure where human induced vibration is very important. In these structures a particular phenomenon appears such as the interaction personstructure (lock-in), the person-person synchronization, and the influence of the mass and damping of the people in the structural behaviour. This paper focuses on the latter topic. In order to evaluate these property modifications several tests have been carried out on a stand-alone building. For the test an electro-dynamic shaker was installed at a fixed point of the gym slab and different groups of people were located around the shaker. The dynamic characteristics of the structure without people inside have been calculated by two methods: using a three-dimensional finite element model of the building and by operational modal analysis. These calculated experimental and numerical values are the reference values used to evaluate the modifications in the dynamic properties of the structure.

Dynamic analysis of payloads and structures with intermediate modal density

La necesidad de desarrollar técnicas para predecir la respuesta vibroacústica de estructuras espaciales lia ido ganando importancia en los últimos años. Las técnicas numéricas existentes en la actualidad son capaces de predecir de forma fiable el comportamiento vibroacústico de sistemas con altas o bajas densidades modales. Sin embargo, ambos rangos no siempre solapan lo que hace que sea necesario el desarrollo de métodos específicos para este rango, conocido como densidad modal media. Es en este rango, conocido también como media frecuencia, donde se centra la presente Tesis doctoral, debido a la carencia de métodos específicos para el cálculo de la respuesta vibroacústica. Para las estructuras estudiadas en este trabajo, los mencionados rangos de baja y alta densidad modal se corresponden, en general, con los rangos de baja y alta frecuencia, respectivamente. Los métodos numéricos que permiten obtener la respuesta vibroacústica para estos rangos de frecuencia están bien especificados. Para el rango de baja frecuencia se emplean técnicas deterministas, como el método de los Elementos Finitos, mientras que, para el rango de alta frecuencia las técnicas estadísticas son más utilizadas, como el Análisis Estadístico de la Energía. En el rango de medias frecuencias ninguno de estos métodos numéricos puede ser usado con suficiente precisión y, como consecuencia -a falta de propuestas más específicas- se han desarrollado métodos híbridos que combinan el uso de métodos de baja y alta frecuencia, intentando que cada uno supla las deficiencias del otro en este rango medio. Este trabajo propone dos soluciones diferentes para resolver el problema de la media frecuencia. El primero de ellos, denominado SHFL (del inglés Subsystem based High Frequency Limit procedure), propone un procedimiento multihíbrido en el cuál cada subestructura del sistema completo se modela empleando una técnica numérica diferente, dependiendo del rango de frecuencias de estudio. Con este propósito se introduce el concepto de límite de alta frecuencia de una subestructura, que marca el límite a partir del cual dicha subestructura tiene una densidad modal lo suficientemente alta como para ser modelada utilizando Análisis Estadístico de la Energía. Si la frecuencia de análisis es menor que el límite de alta frecuencia de la subestructura, ésta se modela utilizando Elementos Finitos. Mediante este método, el rango de media frecuencia se puede definir de una forma precisa, estando comprendido entre el menor y el mayor de los límites de alta frecuencia de las subestructuras que componen el sistema completo. Los resultados obtenidos mediante la aplicación de este método evidencian una mejora en la continuidad de la respuesta vibroacústica, mostrando una transición suave entre los rangos de baja y alta frecuencia. El segundo método propuesto se denomina HS-CMS (del inglés Hybrid Substructuring method based on Component Mode Synthesis). Este método se basa en la clasificación de la base modal de las subestructuras en conjuntos de modos globales (que afectan a todo o a varias partes del sistema) o locales (que afectan a una única subestructura), utilizando un método de Síntesis Modal de Componentes. De este modo es posible situar espacialmente los modos del sistema completo y estudiar el comportamiento del mismo desde el punto de vista de las subestructuras. De nuevo se emplea el concepto de límite de alta frecuencia de una subestructura para realizar la clasificación global/local de los modos en la misma. Mediante dicha clasificación se derivan las ecuaciones globales del movimiento, gobernadas por los modos globales, y en las que la influencia del conjunto de modos locales se introduce mediante modificaciones en las mismas (en su matriz dinámica de rigidez y en el vector de fuerzas). Las ecuaciones locales se resuelven empleando Análisis Estadístico de Energías. Sin embargo, este último será un modelo híbrido, en el cual se introduce la potencia adicional aportada por la presencia de los modos globales. El método ha sido probado para el cálculo de la respuesta de estructuras sometidas tanto a cargas estructurales como acústicas. Ambos métodos han sido probados inicialmente en estructuras sencillas para establecer las bases e hipótesis de aplicación. Posteriormente, se han aplicado a estructuras espaciales, como satélites y reflectores de antenas, mostrando buenos resultados, como se concluye de la comparación de las simulaciones y los datos experimentales medidos en ensayos, tanto estructurales como acústicos. Este trabajo abre un amplio campo de investigación a partir del cual es posible obtener metodologías precisas y eficientes para reproducir el comportamiento vibroacústico de sistemas en el rango de la media frecuencia. ABSTRACT Over the last years an increasing need of novel prediction techniques for vibroacoustic analysis of space structures has arisen. Current numerical techniques arc able to predict with enough accuracy the vibro-acoustic behaviour of systems with low and high modal densities. However, space structures are, in general, very complex and they present a range of frequencies in which a mixed behaviour exist. In such cases, the full system is composed of some sub-structures which has low modal density, while others present high modal density. This frequency range is known as the mid-frequency range and to develop methods for accurately describe the vibro-acoustic response in this frequency range is the scope of this dissertation. For the structures under study, the aforementioned low and high modal densities correspond with the low and high frequency ranges, respectively. For the low frequency range, deterministic techniques as the Finite Element Method (FEM) are used while, for the high frequency range statistical techniques, as the Statistical Energy Analysis (SEA), arc considered as more appropriate. In the mid-frequency range, where a mixed vibro-acoustic behaviour is expected, any of these numerical method can not be used with enough confidence level. As a consequence, it is usual to obtain an undetermined gap between low and high frequencies in the vibro-acoustic response function. This dissertation proposes two different solutions to the mid-frequency range problem. The first one, named as The Subsystem based High Frequency Limit (SHFL) procedure, proposes a multi-hybrid procedure in which each sub-structure of the full system is modelled with the appropriate modelling technique, depending on the frequency of study. With this purpose, the concept of high frequency limit of a sub-structure is introduced, marking out the limit above which a substructure has enough modal density to be modelled by SEA. For a certain analysis frequency, if it is lower than the high frequency limit of the sub-structure, the sub-structure is modelled through FEM and, if the frequency of analysis is higher than the high frequency limit, the sub-structure is modelled by SEA. The procedure leads to a number of hybrid models required to cover the medium frequency range, which is defined as the frequency range between the lowest substructure high frequency limit and the highest one. Using this procedure, the mid-frequency range can be define specifically so that, as a consequence, an improvement in the continuity of the vibro-acoustic response function is achieved, closing the undetermined gap between the low and high frequency ranges. The second proposed mid-frequency solution is the Hybrid Sub-structuring method based on Component Mode Synthesis (HS-CMS). The method adopts a partition scheme based on classifying the system modal basis into global and local sets of modes. This classification is performed by using a Component Mode Synthesis, in particular a Craig-Bampton transformation, in order to express the system modal base into the modal bases associated with each sub-structure. Then, each sub-structure modal base is classified into global and local set, fist ones associated with the long wavelength motion and second ones with the short wavelength motion. The high frequency limit of each sub-structure is used as frequency frontier between both sets of modes. From this classification, the equations of motion associated with global modes are derived, which include the interaction of local modes by means of corrections in the dynamic stiffness matrix and the force vector of the global problem. The local equations of motion are solved through SEA, where again interactions with global modes arc included through the inclusion of an additional input power into the SEA model. The method has been tested for the calculation of the response function of structures subjected to structural and acoustic loads. Both methods have been firstly tested in simple structures to establish their basis and main characteristics. Methods are also verified in space structures, as satellites and antenna reflectors, providing good results as it is concluded from the comparison with experimental results obtained in both, acoustic and structural load tests. This dissertation opens a wide field of research through which further studies could be performed to obtain efficient and accurate methodologies to appropriately reproduce the vibro-acoustic behaviour of complex systems in the mid-frequency range.

Modelización de servicios ecosistémicos en una cuenca hidrológica del área mediterránea = Modeling ecosystem services in a mediterranean area river basin

La modelización es un proceso por el que se obtienen modelos de los procesos del ´mundo real´ mediante la utilización de simplificaciones. Sin embargo, las estimaciones obtenidas con el modelo llevan implícitas incertidumbre que se debe evaluar. Mediante un análisis de sensibilidad se puede mejorar la confianza en los resultados, sin embargo, este paso a veces no se realiza debido básicamente al trabajo que lleva consigo este tipo de análisis. Además, al crear un modelo, hay que mantener un equilibrio entre la obtención de resultados lo más exactos posible mediante un modelo lo más sencillo posible. Por ello, una vez creado un modelo, es imprescindible comprobar si es necesario o no incluir más procesos que en un principio no se habían incluido. Los servicios ecosistémicos son los procesos mediante los cuales los ecosistemas mantienen y satisfacen el bienestar humano. La importancia que los servicios ecosistémicos y sus beneficios asociados tienen, junto con la necesidad de realizar una buena gestión de los mismos, han estimulado la aparición de modelos y herramientas para cuantificarlos. InVEST (Integrated Valuation of Ecosystem Services and Tradoffs) es una de estas herramientas específicas para calcular servicios eco-sistémicos, desarrollada por Natural Capital Project (Universidad de Stanford, EEUU). Como resultado del creciente interés en calcular los servicios eco-sistémicos, se prevé un incremento en la aplicación del InVEST. La investigación desarrollada en esta Tesis pretende ayudar en esas otras importantes fases necesarias después de la creación de un modelo, abarcando los dos siguientes trabajos. El primero es la aplicación de un análisis de sensibilidad al modelo en una cuenca concreta mediante la metodología más adecuada. El segundo es relativo a los procesos dentro de la corriente fluvial que actualmente no se incluyen en el modelo mediante la creación y aplicación de una metodología que estudiara el papel que juegan estos procesos en el modelo InVEST de retención de nutrientes en el área de estudio. Los resultados de esta Tesis contribuirán a comprender la incertidumbre involucrada en el proceso de modelado. También pondrá de manifiesto la necesidad de comprobar el comportamiento de un modelo antes de utilizarlo y en el momento de interpretar los resultados obtenidos. El trabajo en esta Tesis contribuirá a mejorar la plataforma InVEST, que es una herramienta importante en el ámbito de los servicios de los ecosistemas. Dicho trabajo beneficiará a los futuros usuarios de la herramienta, ya sean investigadores (en investigaciones futuras), o técnicos (en futuros trabajos de toma de decisiones o gestión ecosistemas). ABSTRACT Modeling is the process to idealize real-world situations through simplifications in order to obtain a model. However, model estimations lead to uncertainties that have to be evaluated formally. The role of the sensitivity analysis (SA) is to assign model output uncertainty based on the inputs and can increase confidence in model, however, it is often omitted in modelling, usually as a result of the growing effort it involves. In addition, the balance between accuracy and simplicity is not easy to assess. For this reason, when a model is developed, it is necessary to test it in order to understand its behavior and to include, if necessary, more complexity to get a better response. Ecosystem services are the conditions and processes through which natural ecosystems, and their constituent species, sustain and fulfill human life. The relevance of ecosystem services and the need to better manage them and their associated benefits have stimulated the emergence of models and tools to measure them. InVEST, Integrated Valuation of Ecosystem Services and Tradoffs, is one of these ecosystem services-specific tools developed by the Natural Capital Project (Stanford University, USA). As a result of the growing interest in measuring ecosystem services, the use of InVEST is anticipated to grow exponentially in the coming years. However, apart from model development, making a model involves other crucial stages such as its evaluation and application in order to validate estimations. The work developed in this thesis tries to help in this relevant and imperative phase of the modeling process, and does so in two different ways. The first one is to conduct a sensitivity analysis of the model, which consists in choosing and applying a methodology in an area and analyzing the results obtained. The second is related to the in-stream processes that are not modeled in the current model, and consists in creating and applying a methodology for testing the streams role in the InVEST nutrient retention model in a case study, analyzing the results obtained. The results of this Thesis will contribute to the understanding of the uncertainties involved in the modeling process. It will also illustrate the need to check the behavior of every model developed before putting them in production and illustrate the importance of understanding their behavior in terms of correctly interpreting the results obtained in light of uncertainty. The work in this thesis will contribute to improve the InVEST platform, which is an important tool in the field of ecosystem services. Such work will benefit future users, whether they are researchers (in their future research), or technicians (in their future work in ecosystem conservation or management decisions).

Using pMOS Pass-Gates to Boost SRAM Performance by Exploiting Strain Effects in Sub-20-nm FinFET Technologies

Strained fin is one of the techniques used to improve the devices as their size keeps reducing in new nanoscale nodes. In this paper, we use a predictive technology of 14 nm where pMOS mobility is significantly improved when those devices are built on top of long, uncut fins, while nMOS devices present the opposite behavior due to the combination of strains. We explore the possibility of boosting circuit performance in repetitive structures where long uncut fins can be exploited to increase fin strain impact. In particular, pMOS pass-gates are used in 6T complementary SRAM cells (CSRAM) with reinforced pull-ups. Those cells are simulated under process variability and compared to the regular SRAM. We show that when layout dependent effects are considered the CSRAM design provides 10% to 40% faster access time while keeping the same area, power, and stability than a regular 6T SRAM cell. The conclusions also apply to 8T SRAM cells. The CSRAM cell also presents increased reliability in technologies whose nMOS devices have more mismatch than pMOS transistors.