Determination of macromolecular exchange and PO2 in the microcirculation: a simple system for in vivo fluorescence and phosphorescence videomicroscopy

We have developed a system with two epi-illumination sources, a DC-regulated lamp for transillumination and mechanical switches for rapid shift of illumination and detection of defined areas (250-750 µm²) by fluorescence and phosphorescence videomicroscopy. The system permits investigation of standard microvascular parameters, vascular permeability as well as intra- and extravascular PO2 by phosphorescence quenching of Pd-meso-tetra (4-carboxyphenyl) porphine (PORPH). A Pechan prism was used to position a defined region over the photomultiplier and TV camera. In order to validate the system for in vivo use, in vitro tests were performed with probes at concentrations that can be found in microvascular studies. Extensive in vitro evaluations were performed by filling glass capillaries with solutions of various concentrations of FITC-dextran (diluted in blood and in saline) mixed with different amounts of PORPH. Fluorescence intensity and phosphorescence decay were determined for each mixture. FITC-dextran solutions without PORPH and PORPH solutions without FITC-dextran were used as references. Phosphorescence decay curves were relatively unaffected by the presence of FITC-dextran at all concentrations tested (0.1 µg/ml to 5 mg/ml). Likewise, fluorescence determinations were performed in the presence of PORPH (0.05 to 0.5 mg/ml). The system was successfully used to study macromolecular extravasation and PO2 in the rat mesentery circulation under controlled conditions and during ischemia-reperfusion.

Photocytotoxicity of a 5-nitrofuran-ethenyl-quinoline antiseptic (Quinifuryl) to P388 mouse leukemia cells

Quinifuryl (MW 449.52), 2-(5'-nitro-2'-furanyl)ethenyl-4-{N-[4'-(N,N-diethylamino)-1'-methylbutyl]carbamoyl} quinoline, is a water soluble representative of a family of 5-nitrofuran-ethenyl-quinoline drugs which has been shown to be highly toxic to various lines of transformed cells in the dark. In the present study, the toxicity of Quinifuryl to P388 mouse leukemia cells was compared in the dark and under illumination with visible light (390-500 nm). Illumination of water solutions of Quinifuryl (at concentrations ranging from 0.09 to 9.0 µg/ml) in the presence of P388 cells resulted in its photodecomposition and was accompanied by elevated cytotoxicity. A significant capacity to kill P388 cells was detected at a drug concentration as low as 0.09 µg/ml. The toxic effect detected at this drug concentration under illumination exceeded the effect observed in the dark by more than three times. Moreover, the general toxic effect of Quinifuryl, which included cell proliferation arrest, was nearly 100%. Both dose- and time-dependent toxic effects were measured under illumination. The LC50 value of Quinifuryl during incubation with P388 cells was ~0.45 µg/ml under illumination for 60 min and >12 µg/ml in the dark. We have demonstrated that the final products of the Quinifuryl photolysis are not toxic, which means that the short-lived intermediates of Quinifuryl photodecomposition are responsible for the phototoxicity of this compound. The data obtained in the present study are the first to indicate photocytotoxicity of a nitroheterocyclic compound and demonstrate the possibility of its application as a photosensitizer drug for photochemotherapy.

Local Binary Patterns in Focal-Plane Processing. Analysis and Applications

Feature extraction is the part of pattern recognition, where the sensor data is transformed into a more suitable form for the machine to interpret. The purpose of this step is also to reduce the amount of information passed to the next stages of the system, and to preserve the essential information in the view of discriminating the data into different classes. For instance, in the case of image analysis the actual image intensities are vulnerable to various environmental effects, such as lighting changes and the feature extraction can be used as means for detecting features, which are invariant to certain types of illumination changes. Finally, classification tries to make decisions based on the previously transformed data. The main focus of this thesis is on developing new methods for the embedded feature extraction based on local non-parametric image descriptors. Also, feature analysis is carried out for the selected image features. Low-level Local Binary Pattern (LBP) based features are in a main role in the analysis. In the embedded domain, the pattern recognition system must usually meet strict performance constraints, such as high speed, compact size and low power consumption. The characteristics of the final system can be seen as a trade-off between these metrics, which is largely affected by the decisions made during the implementation phase. The implementation alternatives of the LBP based feature extraction are explored in the embedded domain in the context of focal-plane vision processors. In particular, the thesis demonstrates the LBP extraction with MIPA4k massively parallel focal-plane processor IC. Also higher level processing is incorporated to this framework, by means of a framework for implementing a single chip face recognition system. Furthermore, a new method for determining optical flow based on LBPs, designed in particular to the embedded domain is presented. Inspired by some of the principles observed through the feature analysis of the Local Binary Patterns, an extension to the well known non-parametric rank transform is proposed, and its performance is evaluated in face recognition experiments with a standard dataset. Finally, an a priori model where the LBPs are seen as combinations of n-tuples is also presented

Photodynamic antimicrobial chemotherapy (PACT) for the treatment of malaria, leishmaniasis and trypanosomiasis

A photodynamic effect occurs when photosensitiser molecules absorb light and dissipate the absorbed energy by transferring it to biological acceptors (usually oxygen), generating an excess of reactive species that are able to force cells into death pathways. Several tropical diseases present physiopathological aspects that are accessible to the application of a photosensitiser and local illumination. In addition, disease may be transmitted through infected blood donations, and many of the aetiological agents associated with tropical diseases have been shown to be susceptible to the photodynamic approach. However, there has been no systematic investigation of the application of photoantimicrobial agents in the various presentations, whether to human disease or to the disinfection of blood products or even as photo-insecticides. We aim in this review to report the advances in the photoantimicrobial approach that are beneficial to the field of anti-parasite therapy and also have the potential to facilitate the development of low-cost/high-efficiency protocols for underserved populations.

The inhibitory effect of photodynamic therapy and of an anti-VCAM-1 monoclonal antibody on the in vivo growth of C6 glioma xenografts

We investigated the effect of photodynamic therapy (PDT) and of an anti-vascular cell adhesion molecule-1 (VCAM-1) monoclonal antibody on the in vivo growth of C6 glioma. Seven days after inoculation with C6 cells, adult male Wistar rats weighing 280-300 g with MRI-confirmed glioma were randomly assigned to 4 groups (N = 15 per group): PDT + VCAM-1 antibody group; PDT group; VCAM-1 antibody group; control group. Eight days after inoculation, hematoporphyrin monomethyl ether (HMME) was administered as a photosensitizer and PDT was performed at 630 nm (illumination intensity: 360 J/cm²) for 10 min. VCAM-1 antibody (50 µg/mL) was then administered (0.5 mL) through the tail vein every other day from day 8 to day 16. At day 21, 5 rats in each group were sacrificed and cancers were harvested for immunohistochemistry and Western blot assay for the detection of VCAM-1, and TUNEL assay was used to detect apoptosis. Survival and tumor volume were recorded in the remaining 10 rats in each group. In the PDT group, tumor growth was significantly suppressed (67.2%) and survival prolonged (89.3%), accompanied by an increase in apoptosis (369.5%), when compared to control. Furthermore, these changes were more pronounced in the PDT + VCAM-1 antibody group. After PDT, VCAM-1 expression was markedly increased (121.8%) and after VCAM-1 monoclonal antibody treatment, VCAM-1 expression was significantly reduced (58.2%). PDT in combination with VCAM-1 antibody can significantly inhibit the growth of C6 glioma and prolong survival. This approach may represent a promising strategy in the treatment of glioma.

Production of phycobiliproteins by Arthrospira platensis under different lightconditions for application in food products

There has been an increase in investment in research on new sources of natural pigments for food application. Some cyanobacteria can change the structures responsible for light harvesting and cellular processes according to the wavelength and light intensity. This phenomenon has been described as complementary chromatic adaptation. The present study aimed to investigate the growth of Arthrospira platensis using different light qualities, irradiance, and wavelength by evaluating the production of biomass, proteins, and phycobiliproteins. The occurrence of the chromatic adaptation phenomenon in this cyanobacterium was also investigated. The microorganism used in this study, A. platensis, was grown in a Zarrouk medium under three irradiance levels, 50, 100, and 150 μmol fotons.m–2.s–1 with illumination provided by white and green fluorescent lamps. The condition of 150 µmol fotons.m–2.s–1 white light was the one that promoted the highest biomass production of A. platensis cultures (2115.24 mg.L–1). There was no difference in the production of total protein and total phycobiliproteins under the studied conditions. It is likely that the large supply of nitrogen in the Zarrouk medium was sufficient for cell growth and maintenance, and it supplied the production of accessory pigments composed of protein. Finally, there was no evidence of the complementary chromatic adaptation phenomenon in A. platensis cultivated under green light. Moreover, this condition did not increase phycocyanin production.

Mechanical design and optics simulation of the illuminated Volvo Iron mark

Utilization of light and illumination systems in automotive industry for different purposes has been increased significantly in recent years. Volvo as one of the leading companies in manufacturing of luxury cars has found the great capacity in this area. The performance of such an illumination systems is one of the challenges that engineers in this industry are facing with. In this study an effort has been made to design a system to make the iron mark of Volvo being illuminated and the system is being evaluated by optics simulation in software using Ray optics method. At the end, results are assessed and some optimizations are carried out. Different kind of light guides, front side of the iron mark and some possible arrangement for LED also evaluated and different materials tested. The best combination from uniformity, color and amount of luminance aspect selected as a possible solution for this special project which can be used as a base for further studies in Volvo.

Hydrogen Sensor Application of Anodic Titanium Oxide Nanostructures

Hydrogen (H2) fuel cells have been considered a promising renewable energy source. The recent growth of H2 economy has required highly sensitive, micro-sized and cost-effective H2 sensor for monitoring concentrations and alerting to leakages due to the flammability and explosiveness of H2 Titanium dioxide (TiO2) made by electrochemical anodic oxidation has shown great potential as a H2 sensing material. The aim of this thesis is to develop highly sensitive H2 sensor using anodized TiO2. The sensor enables mass production and integration with microelectronics by preparing the oxide layer on suitable substrate. Morphology, elemental composition, crystal phase, electrical properties and H2 sensing properties of TiO2 nanostructures prepared on Ti foil, Si and SiO2/Si substrates were characterized. Initially, vertically oriented TiO2 nanotubes as the sensing material were obtained by anodizing Ti foil. The morphological properties of tubes could be tailored by varying the applied voltages of the anodization. The transparent oxide layer creates an interference color phenomena with white light illumination on the oxide surface. This coloration effect can be used to predict the morphological properties of the TiO2 nanostructures. The crystal phase transition from amorphous to anatase or rutile, or the mixture of anatase and rutile was observed with varying heat treatment temperatures. However, the H2 sensing properties of TiO2 nanotubes at room temperature were insufficient. H2 sensors using TiO2 nanostructures formed on Si and SiO2/Si substrates were demonstrated. In both cases, a Ti layer deposited on the substrates by a DC magnetron sputtering method was successfully anodized. A mesoporous TiO2 layer obtained on Si by anodization in an aqueous electrolyte at 5°C showed diode behavior, which was influenced by the work function difference of Pt metal electrodes and the oxide layer. The sensor enabled the detection of H2 (20-1000 ppm) at low operating temperatures (50–140°C) in ambient air. A Pd decorated tubular TiO2 layer was prepared on metal electrodes patterned SiO2/Si wafer by anodization in an organic electrolyte at 5°C. The sensor showed significantly enhanced H2 sensing properties, and detected hydrogen in the range of a few ppm with fast response/recovery time. The metal electrodes placed under the oxide layer also enhanced the mechanical tolerance of the sensor. The concept of TiO2 nanostructures on alternative substrates could be a prospect for microelectronic applications and mass production of gas sensors. The gas sensor properties can be further improved by modifying material morphologies and decorating it with catalytic materials.

Real-time simulation of multibody systems with applications for working mobile vehicles

This dissertation describes an approach for developing a real-time simulation for working mobile vehicles based on multibody modeling. The use of multibody modeling allows comprehensive description of the constrained motion of the mechanical systems involved and permits real-time solving of the equations of motion. By carefully selecting the multibody formulation method to be used, it is possible to increase the accuracy of the multibody model while at the same time solving equations of motion in real-time. In this study, a multibody procedure based on semi-recursive and augmented Lagrangian methods for real-time dynamic simulation application is studied in detail. In the semirecursive approach, a velocity transformation matrix is introduced to describe the dependent coordinates into relative (joint) coordinates, which reduces the size of the generalized coordinates. The augmented Lagrangian method is based on usage of global coordinates and, in that method, constraints are accounted using an iterative process. A multibody system can be modelled as either rigid or flexible bodies. When using flexible bodies, the system can be described using a floating frame of reference formulation. In this method, the deformation mode needed can be obtained from the finite element model. As the finite element model typically involves large number of degrees of freedom, reduced number of deformation modes can be obtained by employing model order reduction method such as Guyan reduction, Craig-Bampton method and Krylov subspace as shown in this study The constrained motion of the working mobile vehicles is actuated by the force from the hydraulic actuator. In this study, the hydraulic system is modeled using lumped fluid theory, in which the hydraulic circuit is divided into volumes. In this approach, the pressure wave propagation in the hoses and pipes is neglected. The contact modeling is divided into two stages: contact detection and contact response. Contact detection determines when and where the contact occurs, and contact response provides the force acting at the collision point. The friction between tire and ground is modelled using the LuGre friction model, which describes the frictional force between two surfaces. Typically, the equations of motion are solved in the full matrices format, where the sparsity of the matrices is not considered. Increasing the number of bodies and constraint equations leads to the system matrices becoming large and sparse in structure. To increase the computational efficiency, a technique for solution of sparse matrices is proposed in this dissertation and its implementation demonstrated. To assess the computing efficiency, augmented Lagrangian and semi-recursive methods are implemented employing a sparse matrix technique. From the numerical example, the results show that the proposed approach is applicable and produced appropriate results within the real-time period.

Real-time monitoring of laser scribing process utilizing high-speed camera

Currently, laser scribing is growing material processing method in the industry. Benefits of laser scribing technology are studied for example for improving an efficiency of solar cells. Due high-quality requirement of the fast scribing process, it is important to monitor the process in real time for detecting possible defects during the process. However, there is a lack of studies of laser scribing real time monitoring. Commonly used monitoring methods developed for other laser processes such a laser welding, are sufficient slow and existed applications cannot be implemented in fast laser scribing monitoring. The aim of this thesis is to find a method for laser scribing monitoring with a high-speed camera and evaluate reliability and performance of the developed monitoring system with experiments. The laser used in experiments is an IPG ytterbium pulsed fiber laser with 20 W maximum average power and Scan head optics used in the laser is Scanlab’s Hurryscan 14 II with an f100 tele-centric lens. The camera was connected to laser scanner using camera adapter to follow the laser process. A powerful fully programmable industrial computer was chosen for executing image processing and analysis. Algorithms for defect analysis, which are based on particle analysis, were developed using LabVIEW system design software. The performance of the algorithms was analyzed by analyzing a non-moving image from the scribing line with resolution 960x20 pixel. As a result, the maximum analysis speed was 560 frames per second. Reliability of the algorithm was evaluated by imaging scribing path with a variable number of defects 2000 mm/s when the laser was turned off and image analysis speed was 430 frames per second. The experiment was successful and as a result, the algorithms detected all defects from the scribing path. The final monitoring experiment was performed during a laser process. However, it was challenging to get active laser illumination work with the laser scanner due physical dimensions of the laser lens and the scanner. For reliable error detection, the illumination system is needed to be replaced.

Spectral retinal image processing and analysis for ophthalmology

Diabetic retinopathy, age-related macular degeneration and glaucoma are the leading causes of blindness worldwide. Automatic methods for diagnosis exist, but their performance is limited by the quality of the data. Spectral retinal images provide a significantly better representation of the colour information than common grayscale or red-green-blue retinal imaging, having the potential to improve the performance of automatic diagnosis methods. This work studies the image processing techniques required for composing spectral retinal images with accurate reflection spectra, including wavelength channel image registration, spectral and spatial calibration, illumination correction, and the estimation of depth information from image disparities. The composition of a spectral retinal image database of patients with diabetic retinopathy is described. The database includes gold standards for a number of pathologies and retinal structures, marked by two expert ophthalmologists. The diagnostic applications of the reflectance spectra are studied using supervised classifiers for lesion detection. In addition, inversion of a model of light transport is used to estimate histological parameters from the reflectance spectra. Experimental results suggest that the methods for composing, calibrating and postprocessing spectral images presented in this work can be used to improve the quality of the spectral data. The experiments on the direct and indirect use of the data show the diagnostic potential of spectral retinal data over standard retinal images. The use of spectral data could improve automatic and semi-automated diagnostics for the screening of retinal diseases, for the quantitative detection of retinal changes for follow-up, clinically relevant end-points for clinical studies and development of new therapeutic modalities.

Confocal and two-photon microscopy : image enhancement /

Confocal and two-photon microcopy have become essential tools in biological research and today many investigations are not possible without their help. The valuable advantage that these two techniques offer is the ability of optical sectioning. Optical sectioning makes it possible to obtain 3D visuahzation of the structiu-es, and hence, valuable information of the structural relationships, the geometrical, and the morphological aspects of the specimen. The achievable lateral and axial resolutions by confocal and two-photon microscopy, similar to other optical imaging systems, are both defined by the diffraction theorem. Any aberration and imperfection present during the imaging results in broadening of the calculated theoretical resolution, blurring, geometrical distortions in the acquired images that interfere with the analysis of the structures, and lower the collected fluorescence from the specimen. The aberrations may have different causes and they can be classified by their sources such as specimen-induced aberrations, optics-induced aberrations, illumination aberrations, and misalignment aberrations. This thesis presents an investigation and study of image enhancement. The goal of this thesis was approached in two different directions. Initially, we investigated the sources of the imperfections. We propose methods to eliminate or minimize aberrations introduced during the image acquisition by optimizing the acquisition conditions. The impact on the resolution as a result of using a coverslip the thickness of which is mismatched with the one that the objective lens is designed for was shown and a novel technique was introduced in order to define the proper value on the correction collar of the lens. The amoimt of spherical aberration with regard to t he numerical aperture of the objective lens was investigated and it was shown that, based on the purpose of our imaging tasks, different numerical apertures must be used. The deformed beam cross section of the single-photon excitation source was corrected and the enhancement of the resolution and image quaUty was shown. Furthermore, the dependency of the scattered light on the excitation wavelength was shown empirically. In the second part, we continued the study of the image enhancement process by deconvolution techniques. Although deconvolution algorithms are used widely to improve the quality of the images, how well a deconvolution algorithm responds highly depends on the point spread function (PSF) of the imaging system applied to the algorithm and the level of its accuracy. We investigated approaches that can be done in order to obtain more precise PSF. Novel methods to improve the pattern of the PSF and reduce the noise are proposed. Furthermore, multiple soiu'ces to extract the PSFs of the imaging system are introduced and the empirical deconvolution results by using each of these PSFs are compared together. The results confirm that a greater improvement attained by applying the in situ PSF during the deconvolution process.

Synthesis and characterization of BODIPY-α-tocopherol : a new ligand to explore the intracellular transfer of Vitamin E

Since its discovery nearly a century ago, a-tocopherol (vitamin E) research has been mainly focused on its ability to terminate the cycle of lipid peroxidation in membranes. Nitrobenzoxadiazole fluorescent analogues were made previously to study the intracellular transfer of vitamin E in cells. However, these molecules were reportedly susceptible to photobleaching while under illumination for transfer assays and microscopy. Here is reported the synthesis of a series of fluorescent analogues of vitamin E incorporating the more robust dipyrrometheneboron difluoride fluorophore (BDP-a-Tocs; Aex = 507 nm, Aem = 511 nm). C8-BDP-a-Toc 42c, having an eight-carbon chain between the chromanol and fluorophore, wa<; shown to bind specifically to a-tocopherol transfer protein with a dissociation constant of approximately 100 nM. Another fluorescent analogue of vitamin E with a thienyl derivative of BODIPY that is excited and fluoresces at longer wavelengths (Aex = 561 nm, Aem = 570 nm) is in development.

SYNTHESIS OF CYCLIC AZOBENZENE ANALOGUES FOR INCORPORATION INTO OLIGONUCLEOTIDES, PEPTIDES AND POLYMERS

(A) In recent years, considerable amount of effort has contributed towards enhancing our understanding of the new photoswitch, cyclic azobenzene, particularly from the theoretical point of view. However, the challenging part with this system was poor efficiency of its synthesis from 2,2’- dinitrodibenzyl and lack of effective methods for further modification which would be useful to incorporate this system into biomolecules as a photoswitch. We report the synthesis of cyclic azobenzene and analogues from 2,2’-dinitrodibenzyl, which would allow for further incorporation of this cyclic azobenzene into biomolecules. Reaction of 2,2’-dinitrodibenzyl with zinc metal powder in the presence of triethylammonium formate buffer (pH-9.5) gave a cyclic azoxybenzene, 11,12-dihydrodibenzo[c,g][1,2]diazocine-5-oxide. The latter compound was converted into cyclic azobenzene analogues (bromo-, chloro-, cyano-, and carboxyl) through subsequent transformations. The carboxylic acid analogue was reacted with D-threoninol to give the corresponding amide, which readily undergoes photo-isomerization upon illumination with light. Upon illumination with light at 400 nm, approximately 70% of cis- isomer of amide was isomerized to trans- isomer. It was observed that cis- to trans- isomerization reached the maximum steady state of light transmission after approximately 40 min, whereas the trans- to cis- isomerization approximately acquired in 2 h to regain full recovery of light transmission. Cyclic azobenzene phosphoramidite was synthesized from DMT-protected D-threoninol linked cyclic azobenzene. (B) In recent years, there has been considerable interest invested towards the synthesis of azobenzene analogues for incorporation into proteins. Among the many azobenzene analogues, the synthesis of bi-functional cyclic azobenzene analogues for the incorporation into proteins is relatively new. In this thesis, we report the synthesis of a cyclic azobenzene biscarboxylic acid from 4-(bromomethyl)benzonitrile. (C) Azobenzene has been widely used in the field of polymer science to study the surface morphology and surface properties of polymers. In this thesis, we report the incorporation of cyclic azobenzene into a commercial polymer 2- (hydroxyethyl)methacrylate. Samples collected after 24 h from the reaction solution showed approximately 9% of incorporation of cyclic azobenzene into polymer compared to samples collected after 10 h, which showed approximately 6% incorporation.

The Prince’s Visit to St. Catharines Broadside, 1860

Broadside advertising the appearance of the Prince of Wales, Albert Edward, who was Queen Victoria’s eldest son. He was to become Edward VII. The visit took place on Tuesday, the 18th of September in 1860. The broadside measures 20 cm. x 17.5 cm. The Royal Coat of Arms is featured on the top. Different typefaces are used throughout the broadside. The Broadside reads: "The Prince's Visit to St. Catharines. His Royal Highness will be at St. Catharines on Tuesday, the 18th Sept. 1860. The Committee of Management express the earnest hope that the Inhabitants of the Counties of Lincoln & Welland Generally, will manifest their Loyalty by joining in an enthusiastic demonstration to the Prince. Come Early to get Seats! As the accommodation in the Amphitheatre will be limited. A Grand Procession Of Firemen and other Public Bodies will be formed, accompanied by Bands of Music. A Royal Salute Will be fired by the St. Catharines Volunteer Artillery Company; and British Cheers will be given by the assembled assembled thousands. A General Illumination in the Evening! God Save The Queen! C.P. Camp, Sec'y to Committee. St. Catharines, September 15, 1860."