Comparison of different stomatal conductance algorithms for ozone flux modelling

A multiplicative and a semi-mechanistic, BWB-type [Ball, J.T., Woodrow, I.E., Berry, J.A., 1987. A model predicting stomatalconductance and its contribution to the control of photosynthesis under different environmental conditions. In: Biggens, J. (Ed.), Progress in Photosynthesis Research, vol. IV. Martinus Nijhoff, Dordrecht, pp. 221–224.] algorithm for calculating stomatalconductance (gs) at the leaf level have been parameterised for two crop and two tree species to test their use in regional scale ozone deposition modelling. The algorithms were tested against measured, site-specific data for durum wheat, grapevine, beech and birch of different European provenances. A direct comparison of both algorithms showed a similar performance in predicting hourly means and daily time-courses of gs, whereas the multiplicative algorithm outperformed the BWB-type algorithm in modelling seasonal time-courses due to the inclusion of a phenology function. The re-parameterisation of the algorithms for local conditions in order to validate ozone deposition modelling on a European scale reveals the higher input requirements of the BWB-type algorithm as compared to the multiplicative algorithm because of the need of the former to model net photosynthesis (An)

Growth response to ozone of annual species from Mediterranean pastures

Ozone (O3) phytotoxicity has been reported on a wide range of plant species. However, scarce information has been provided regarding the sensitivity of semi-natural grassland species, especially those from dehesa Mediterranean grasslands, in spite of their great biological diversity and the high O3 levels recorded in the region. A screening study was carried out in open-top chambers (OTCs) to assess the O3-sensitivity of representative therophytes of these ecosystems based on the response of selected growth-related parameters. Three O3 treatments and 3 OTCs per treatment were used. Legume species were very sensitive to O3, because 78% of the tested species showed detrimental effects on their total biomass relative growth rate (RGR) following their exposure to O3. The Trifolium genus was particularly sensitive showing O3-induced adverse effects on most of the assessed parameters. Gramineae plants were less sensitive than Leguminosae species because detrimental effects on total biomass RGR were only observed in 14% of the assessed species. No relationship was found between relative growth rates when growing in clean air and O3 susceptibility. The implications of these effects on the performance of dehesa acidic grasslands and on the definition of ozone critical levels for the protection of semi-natural vegetation are discussed.

Recuperación de energía de la salmuera

Como consecuencia del proceso de desalación, se produce el vertido al mar de un agua de rechazo hipersalino o salmuera. La salinidad de este vertido es variable, dependiendo del origen de la captación y del proceso de tratamiento. Muchos de los hábitats y biocenosis de los ecosistemas marinos se encuentran adaptados a ambientes de salinidad casi constante y son muy susceptibles a los incrementos de salinidad originados por estos vertidos. Junto con el vertido de salmuera otro de los principales inconvenientes que plantean las plantas desaladoras es el alto consumo energético, con todas las desventajas que esto supone: alto coste del agua desalada para los consumidores, contaminación del medio... El desarrollo de los métodos de vertido, herramientas de gestión de la salmuera, estudios del comportamiento de la pluma salina… ha buscado la mitigación de estos efectos sobre los ecosistemas marinos. El desarrollo en membranas de ósmosis inversa, diseño de bombas y sistemas de recuperación de energía ha permitido también la reducción del consumo energético en las plantas de desalación. Sin embargo, estos campos parecen haber encontrado un techo tecnológico difícil de rebasar en los últimos tiempos. La energía osmótica se plantea como uno de los caminos a investigar aplicado al campo de la reducción del consumo energético en desalación de agua de mar, a través del aprovechamiento energético de la salmuera. Con esta tesis se pretende cumplir principalmente con los siguientes objetivos: reducción del consumo energético en desalación, mitigar el impacto del vertido sobre el medio y ser una nueva herramienta en la gestión de la salmuera. En el presente documento se plantea el desarrollo de un nuevo proceso que utiliza el fenómeno de la ósmosis directa a través de membranas semipermeables, y busca la sinergia desalación depuración, integrando ambos, en un único proceso de tratamiento dentro del ciclo integral del agua. Para verificar los valores de producción, calidad y rendimiento del proceso, se proyecta y construye una planta piloto ubicada en la Planta Desaladora de Alicante II, escalada de tal manera que permite la realización de los ensayos con equipos comerciales de tamaño mínimo. El objetivo es que el resultado final sea extrapolable a tamaños superiores sin que el escalado afecte a la certeza y fiabilidad de las conclusiones obtenidas. La planta se proyecta de forma que el vertido de una desaladora de ósmosis inversa junto con el vertido de un terciario convencional, se pasan por una ósmosis directa y a continuación por una ósmosis inversa otra vez, ésta última con el objeto de abrir la posibilidad de incrementar la producción de agua potable. Ambas ósmosis están provistas de un sistema de pretratamiento físico-químico (para adecuar la calidad del agua de entrada a las condiciones requeridas por las membranas en ambos casos), y un sistema de limpieza química. En todos los ensayos se usa como fuente de disolución concentrada (agua salada), el rechazo de un bastidor de ósmosis inversa de una desaladora convencional de agua de mar. La fuente de agua dulce marca la distinción entre dos tipos de ensayos: ensayos con el efluente del tratamiento terciario de una depuradora convencional, con lo que se estudia el comportamiento de la membrana ante el ensuciamiento; y ensayos con agua permeada, que permiten estudiar el comportamiento ideal de la membrana. Los resultados de los ensayos con agua salobre ponen de manifiesto problemas de ensuciamiento de la membrana, el caudal de paso a través de la misma disminuye con el tiempo y este efecto se ve incrementado con el aumento de la temperatura del agua. Este fenómeno deriva en una modificación del pretratamiento de la ósmosis directa añadiendo un sistema de ultrafiltración que ha permitido que la membrana presente un comportamiento estable en el tiempo. Los ensayos con agua permeada han hecho posible estudiar el comportamiento “ideal” de la membrana y se han obtenido las condiciones óptimas de operación y a las que se debe tender, consiguiendo tasas de recuperación de energía de 1,6; lo que supone pasar de un consumo de 2,44 kWh/m3 de un tren convencional de ósmosis a 2,28 kWh/m3 al añadir un sistema de ósmosis directa. El objetivo de futuras investigaciones es llegar a tasas de recuperación de 1,9, lo que supondría alcanzar consumos inferiores a 2 kWh/m3. Con esta tesis se concluye que el proceso propuesto permite dar un paso más en la reducción del consumo energético en desalación, además de mitigar los efectos del vertido de salmuera en el medio marino puesto que se reduce tanto el caudal como la salinidad del vertido, siendo además aplicable a plantas ya existentes y planteando importantes ventajas económicas a plantas nuevas, concebidas con este diseño. As a consequence of the desalination process, a discharge of a hypersaline water or brine in the sea is produced. The salinity of these discharges varies, depending on the type of intake and the treatment process. Many of the habitats and biocenosis of marine ecosystems are adapted to an almost constant salinity environment and they are very susceptible to salinity increases caused by these discharges. Besides the brine discharge, another problem posed by desalination plants, is the high energy consumption, with all the disadvantages that this involves: high cost of desalinated water for consumers, environmental pollution ... The development of methods of disposal, brine management tools, studies of saline plume ... has sought the mitigation of these effects on marine ecosystems. The development of reverse osmosis membranes, pump design and energy recovery systems have also enabled the reduction of energy consumption in desalination plants. However, these fields seem to have reached a technological ceiling which is difficult to exceed in recent times. Osmotic power is proposed as a new way to achieve the reduction of energy consumption in seawater desalination, through the energy recovery from the brine. This thesis mainly tries to achieve the following objectives: reduction of energy consumption in desalination, mitigation of the brine discharge impact on the environment and become a new tool in the management of the brine. This paper proposes the development of a new process, that uses the phenomenon of forward osmosis through semipermeable membranes and seeks the synergy desalination-wastewater reuse, combining both into a single treatment process within the integral water cycle. To verify the production, quality and performance of the process we have created a pilot plant. This pilot plant, located in Alicante II desalination plant, has been designed and built in a scale that allows to carry out the tests with minimum size commercial equipment. The aim is that the results can be extrapolated to larger sizes, preventing that the scale affects the accuracy and reliability of the results. In the projected plant, the discharge of a reverse osmosis desalination plant and the effluent of a convencional tertiary treatment of a wastewater plant, go through a forward osmosis module, and then through a reverse osmosis, in order to open the possibility of increasing potable water production. Both osmosis systems are provided with a physicochemical pretreatment (in order to obtain the required conditions for the membranes in both cases), and a chemical cleaning system. In all tests, it is used as a source of concentrated solution (salt water), the rejection of a rack of a conventional reverse osmosis seawater desalination. The source of fresh water makes the difference between two types of tests: test with the effluent from a tertiary treatment of a conventional wastewater treatment plant (these tests study the behavior of the membrane facing the fouling) and tests with permeate, which allow us to study the ideal behavior of the membrane. The results of the tests with brackish water show fouling problems, the flow rate through the membrane decreases with the time and this effect is increased with water temperature. This phenomenon causes the need for a modification of the pretreatment of the direct osmosis module. An ultrafiltration system is added to enable the membrane to present a stable behavior . The tests with permeate have made possible the study of the ideal behavior of the membrane and we have obtained the optimum operating conditions. We have achieved energy recovery rates of 1.6, which allows to move from a consumption of 2.44 kWh/m3 in a conventional train of reverse osmosis to 2.28 kWh / m3 if it is added the direct osmosis system. The goal of future researches is to achieve recovery rates of 1.9, which would allow to reach a consumption lower than 2 kWh/m3. This thesis concludes that the proposed process allows us to take a further step in the reduction of the energy consumption in desalination. We must also add the mitigation of the brine discharge effects on the marine environment, due to the reduction of the flow and salinity of the discharge. This is also applicable to existing plants, and it suggests important economic benefits to new plants that will be built with this design.

Implementation of a module for risk of ozone impacts assessment to vegetation in the integrated assessment modelling system for the Iberian peninsula. Evaluation for wheat and holm oak

A module to estimate risks of ozone damage to vegetation has been implemented in the Integrated Assessment Modelling system for the Iberian Peninsula. It was applied to compute three different indexes for wheat and Holm oak; daylight AOT40 (cumulative ozone concentration over 40 ppb), cumulative ozone exposure index according to the Directive 2008/50/EC (AOT40-D) and PODY (Phytotoxic Ozone Dose over a given threshold of Y nmol m−2 s−1). The use of these indexes led to remarkable differences in spatial patterns of relative ozone risks on vegetation. Ozone critical levels were exceeded in most of the modelling domain and soil moisture content was found to have a significant impact on the results. According to the outputs of the model, daylight AOT40 constitutes a more conservative index than the AOT40-D. Additionally, flux-based estimations indicate high risk areas in Portugal for both wheat and Holm oak that are not identified by AOT-based methods.

Desarrollo experimental de un elemento constructivo de envolvente, no estructural, a partir de una matriz de plástico reciclado, reforzado con fibras naturales y/o sintéticas

Esta Tesis trata sobre el diseño y desarrollo de un material constructivo de fachada (tras ventilada), empleando plástico reciclado (granza de caucho, de neumáticos fuera de uso) para su elaboración. El uso de materiales reciclados para la elaboración de nuevos materiales constructivos, es a día de hoy, un valor agregado que contribuye tanto a la disminución de desechos tóxicos, como a la fabricación de productos de alta calidad. La investigación partió de la necesidad de comprender qué es un plástico, cómo son producidos, cuáles son los factores que permitían su reciclaje y qué propiedades podrían ser aprovechadas para desarrollar un nuevo material constructivo. En el estado del arte, fueron analizados los aspectos del plástico relacionados a su composición, propiedades, tipologías, producción, consumo, legislación europea y española, reciclaje y valorización energética. Para analizar más profundamente los materiales desarrollados a partir de plásticos reciclados, desde textiles hasta elementos constructivos. Con el conocimiento adquirido mediante este análisis previo, se diseñó una metodología de experimentación, utilizando caucho reciclado y derivados del yeso como agregados, en una matriz de resinas poliméricas reforzada con fibras naturales y sintéticas. Los resultados obtenidos en los ensayos físicos y térmicos, con los elementos producidos, demostraron que el material tiene una excelente resistencia a tensión así como una baja conductividad térmica. Esta investigación, servirá como precedente para el desarrollo de nuevos materiales y sistemas constructivos, utilizando agregados de plástico reciclado, en los procesos de fabricación. Ya que ha comprobado el enorme potencial que ofrecen, creando nuevos materiales, y contribuyendo a reducir la contaminación medio ambiental. "La mayor recompensa de nuestro trabajo no es lo que nos pagan por él, sino aquello en lo que nos convierte". John Ruskin Material compuesto (Composite) de caucho reciclado, fibras y resinas poliméricas. ABSTRACT This thesis deals with the design and development of a new facade construction material using recycled plastic (rubber pellets from used tires) for processing. The use of recycled materials for the development of new building materials, today is an added value which contributes both to the reduction of toxic waste, as well as the processing of products of good quality. The research derives from the need to understand what a plastic is, how they are produced, what the factors that allowed recycling are and what properties can be exploited to develop a new building material. In the prior art, were analyzed plastic aspects related to its composition, properties, typologies, production, consumption, European and Spanish legislation, recycling and energy recovery. To further analyze the materials developed from recycled plastics, from textiles to construction elements. With the knowledge gained from this previous analysis, we designed an experimental approach using recycled rubber and plaster derivatives as aggregates in a polymeric resin matrix reinforced with natural and synthetic fibers. The results obtained in physical and thermal testing, with the elements produced, showed that the material has excellent tensile strength and a low thermal conductivity. This research will serve as a precedent for the development of new materials and building systems, using recycled plastic aggregates in the manufacturing processes. Since it was found the enormous potential, creating new materials, and helping reduce environmental pollution. "The greatest reward of our work is not what we get paid for it, but what they make us."

Nitrogen deposition alters nitrogen cycling and reduces soil carbon content in low-productivity semiarid Mediterranean ecosystems.

Anthropogenic N deposition poses a threat to European Mediterranean ecosystems. We combined data from an extant N deposition gradient (4.3–7.3 kg N ha−1 yr−1) from semiarid areas of Spain and a field experiment in central Spain to evaluate N deposition effects on soil fertility, function and cyanobacteria community. Soil organic N did not increase along the extant gradient. Nitrogen fixation decreased along existing and experimental N deposition gradients, a result possibly related to compositional shifts in soil cyanobacteria community. Net ammonification and nitrification (which dominated N-mineralization) were reduced and increased, respectively, by N fertilization, suggesting alterations in the N cycle. Soil organic C content, C:N ratios and the activity of β-glucosidase decreased along the extant gradient in most locations. Our results suggest that semiarid soils in low-productivity sites are unable to store additional N inputs, and that are also unable to mitigate increasing C emissions when experiencing increased N deposition.

Bioaccessibility of heavy metals and risk assessment in urban gardens of Madrid

Human health problems and solutions. Urban gardening has spread worldwide in recent years as it enhances food security and selfsupply and promotes community integration. However urban soils are significantly enriched in trace elements relative to background levels. Exposure to the soil in urban gardens may therefore result in adverse health effects depending on the degree of contact during gardening, infant recreational activities and ingestion of vegetables grown in them. In order to evaluate this potential risk, 36 composite samples were collected from the top 20 cm of the soil of 6 urban gardens in Madrid. The aqua regia (pseudototal) and glycine-extractable (bioaccessible) concentrations of Co, Cr, Cu, Ni, Pb and Zn were determined by atomic absorption spectrophotometry. Additionally, pH, texture, Fe, Ca, and Mn concentrations, and organic matter and calcium carbonate contents were determined in all urban gardens and their influence on trace element bioaccessibility was analyzed.

Procesos de depuración de los efluentes líquidos de actividades petrolíferas

La Tesis Doctoral surge debida de los problemas de contaminación ambientales que presentan los efluentes líquidos refinería del petróleo y las industrias de extracción del petróleo crudo en la zona costera de Angola principalmente en las provincias de Cabinda, Zaire y Luanda, en las cuales sus vertidos destruyen la flora y fauna acuática. El objetivo de este trabajo consiste en implementar nuevas técnicas de los procesos de oxidación avanzada para el tratamiento de los efluentes líquidos de refinerías de petróleo, que permitan conseguir una calidad adecuada de los vertidos. Este sector se considera como una fuente de contaminación del medio ambiente, que requiere un control estricto y un tratamiento adecuado para la eliminación de los contaminantes existente en este tipo de agua y posteriormente poder reutilizar estas aguas tratadas para otros fines industriales o verter a los cauces receptores que al menos no perjudique a los ecosistemas. En esta tesis se ha investigado las técnicas más modernas de los procesos de oxidación avanzada para el tratamiento de agua residual de refinería de petróleo, así como: 1) ozonización, 2) peróxido de hidrógeno con ozono, y 3) ultravioleta con ozono. Los resultados obtenidos en este trabajo muestran que el proceso de ozonización simple, ha dado mejores resultados para el tratamiento de este tipo agua residual de petróleo, tanto, en la eliminación de materia orgánica y los fenoles presentes en el agua residual. En la primera fase, con 1 litro de muestra, se alcanzó un rendimiento del 80% en la eliminación de la DQO utilizando 5,97 mg/l de dosis de ozono, con 11 minutos de tiempo de contacto. Respecto a los fenoles se alcanzó una eliminación del 100 % con la misma dosis de ozono y con 11 minutos de tiempo de contacto. En la segunda fase, con 4 litros de muestra, se alcanzó un rendimiento del 66% de la DQO utilizando 22,21 mg/l de dosis de ozono, con 15 minutos de tiempo de contacto y el rendimiento en la eliminación de los fenoles fue de 90 % a las mismas condiciones. The doctoral thesis arises because of environmental pollution problems posed by liquid effluents and oil refinery industries extraction of crude oil in the coastal area of Angola mainly in the provinces of Cabinda, Zaire and Luanda, in which their discharges destroy aquatic flora and fauna. The objective of this work is to implement new techniques of advanced oxidation processes for the treatment of liquid effluents of oil refineries that will achieve an adequate quality of discharges. This sector is considered as a source of environmental pollution, which requires close monitoring and appropriate treatment for the removal of existing contaminants in this water and then treated to reuse this water for other industrial purposes or discharging into streams receptors that at least does not harm ecosystems. In this thesis we investigate the most modern techniques of advanced oxidation processes for treatment of wastewater from oil refinery and: 1) ozonation, 2) hydrogen peroxide, ozone, and 3) radiation with ozone. The results obtained in this study show that the ozonation process simple, has yielded better results for treating wastewater of this type of oil, so the removal of phenols and organic matter present in the wastewater. In the first phase, with 1 liter of sample was reached in 80% yield COD removal using 5.97 mg/l ozone dosage, with 11 minutes of contact time. Regarding phenols elimination was achieved of 100% with the same dose of ozone and 11 minutes contact time In the second phase, with sample 4 liters was reached in 66% yield using 22.21 COD mg / l ozone dosage, with 15 minutes of contact time and the performance in the removal of phenols was of 90% at the same conditions.

Some aspects of lubrication in heavy regimes: thermal effects, stability and turbulence

In this work, a combination of numerical methods applied to thermohydrodynamic lubrication problems with cavitation is presented. It should be emphasized the difficulty of the nonlinear mathematical coupled model involving a free boundary problem, but also the simplicity of the algorithms employed to solve it. So, finite element discretizations for the hydrodynamic and thermal equations combined with upwind techniques for the convection terms and duality methods for nonlinear features are proposed. Additionally, a model describing the movement of the shaft is provided. Considering the shaft as a rigid body this model will consist of an ODE system relating acceleration of the center of gravity and external and pressure loads. The numerical experiments of mechanical stability try to clarify the position of the neutral stability curve. Finally, a rotating machine for ship propulsion involving both axial and radial bearings operating with nonconventional lubricants (seawater to avoid environmental pollution) is analyzed by using laminar and turbulent inertial flows.

Investigación sobre fermentaciones metánicas de desechos estacionales

En el campo agrícola se producen una serie de desechos orgánicos, que por un lado representan serios problemas de contaminación ambiental y por otro el desperdicio de valores energéticos importantes. Es decir una acción contraria a la sostenibilidad que debe buscarse en este siglo XXI. Entre estos productos agrícolas pueden citarse la pulpa de café, residuos herbáceos, bagazo de caña y la fracción insoluble de estiércol de ganado porcino conocida como cerdaza. Un problema añadido para dar solución adecuada es la disponibilidad de estos solo en cortas épocas del año. Todo lo anterior ha sido el origen de la presente investigación, para dar solución adecuada tanto en el aprovechamiento de biogás como en la reducción de la contaminación. La investigación descrita en este documento contempla el desarrollo de los siguientes aspectos: 1) Caracterización y problemática de cada uno de los productos señalados, 2) la solución al problema mediante el proceso de digestión anaerobia con fases separadas con el aprovechamiento del biogás generados y 3) recomendaciones para el arranque del proceso de digestión anaerobia y su mantenimiento en una alternancia de los productos citados. En la primera etapa de la fase experimental se estimó el rendimiento específico de metano para los diferentes sustratos, utilizando reactores batch configurados en una y dos fases concluyendo que la digestión anaerobia en dos fases presenta diferentes ventajas sobre la digestión monoetapa. En general se obtuvo un mayor rendimiento en la producción de metano, una reducción en los tiempos de retención, mayor eficiencia en la eliminación de los sólidos volátiles agregados, y una mayor estabilidad en el proceso reflejado en el mantenimiento de valores de pH en los rangos de operación recomendados. Seguidamente, al comparar dos procesos para la puesta en marcha de digestores metanogénicos operados en forma continua, se concluye que las variables determinantes en la estabilidad del sistema son la alcalinidad total presente en el digestor, el establecimiento de la población de microorganismos y la carga orgánica aplicada. Las dos primeras están determinadas por la calidad y proporción del inóculo suministrado al inicio del proceso. La alternación de sustratos suministrados al sistema de digestión en dos fases, permitió determinar el impacto sobre el desempeño del mismo, registrando una reducción en la producción de biogás, la riqueza de metano y la eficiencia de eliminación de sólidos volátiles durante los primeros días de operación luego del cambio de sustrato. Este periodo corresponde al proceso de aclimatación de los microorganismos el cual requirió de 20 días para asimilar los componentes del nuevo sustrato. Finalmente, entre los sustratos analizados, la menor carga orgánica de operación para mantener la operación del sistema en continuo corresponde a la pulpa de café con 0.1 kg SV/m3. La composición de este sustrato favorece la rápida acumulación de acidez volátil en el sistema, proporcionando una tendencia a la acidificación. Sin embargo, al controlar las cargas orgánicas volumétricas, el sistema permaneció operando sin necesidad de adición de alcalinizantes. La aplicación de los resultados de la presente investigación a la problemática de residuos de café es alentadora, comprobando que el sistema puede ser operado en continuo alternando residuos boreales y pulpa de café, ambos sustratos disponibles en las plantas de procesamiento de la cereza de café. ABSTRACT In the agricultural field there are series of organic wastes, which in one hand are the source of serious problems of environmental pollution and in the other, they represent a residue that could be used as a feedstock with significant energy values. These actions are contrary to efforts towards sustainability, which should be a priority in this century. Among agricultural residues with significant abundance, the coffee pulp, herbaceous waste, sugarcane bagasse and the insoluble fraction of pig manure can be mentioned. An added problem to the development of appropriate treatment systems, which provides a solution to the disposal of such wastes, is the limited availability of these feedstocks only in short seasons. These arguments have been the source of our research, in order to provide properly measures to biogas usage and pollution reduction. The research presented in this document includes the approaches to the following aspects. 1) Characterization and problems regarding the selected feedstocks 2) the solution to the problem by anaerobic digestion process with separate phases and 3) recommendations for starting the process of anaerobic digestion and its maintenance with alternation of the products listed For the first stage of the experimental phase, the specific methane yield of the selected feedstocks was estimated using batch reactors configured in one and two phases. It was concluded that two-phase anaerobic digestion offered distinct advantages over the single-stage digestion. In general a higher methane production yields, lower retention times, higher efficiency in volatile solids removal, and increased stability among the process were obtained. When comparing two processes for starting up methanogenic digesters, it is concluded that the variables that determine the stability of the system are the total alkalinity in the digester, the establishment of the population of microorganisms and the organic load. The first variables are influenced by the proportion and quality of the inoculum supplied at the beginning of the process. The alternation of substrates gave as a result a negative impact on system performance, recording a reduction on biogas production, the methane concentration and the efficiency of volatile solids removal. The situation was observed during the first days of operation after the change of feeding. This period corresponds to the process of acclimatization of the microorganisms which required 20 days to assimilate new substrate components. Finally, among substrates studied, the lowest organic load applied to maintain a continuous operation of the system, corresponds to the coffee pulp with 0.1 kg VS / m3. The composition of this substrate promotes a rapid accumulation of volatile acidity within the system, providing a tendency to acidification. However, by controlling organic loads, the operating system remained stable without addition of alkalizing components. The application of the results of this research to the problem of coffee waste is promising, proving that an anaerobic system can be operated continuously by alternating boreal waste and coffee pulp, both substrates available in coffee processing plants.

Exposição a substâncias organocloradas em São Paulo: níveis séricos em doadores de sangue e fatores associados

A utilização de pesticidas organoclorados é motivo de preocupação das entidades ligadas à área de saúde em todo o mundo. Apesar de as formas de contaminação serem bem conhecidas, não há um controle eficaz na fiscalização do seu uso no Brasil. Sabe-se que altos níveis séricos destes compostos nos organismos de seres humanos e animais acarretam sérios problemas de saúde. Tendo em vista essa realidade, foi realizado, em 2009, o Projeto Piloto do I Inquérito Nacional de Populações Expostas a Substâncias Químicas, cujo subprojeto \"doadores de sangue\" teve como objetivo mensurar as concentrações de substâncias químicas no sangue de 547 residentes da região metropolitana de São Paulo, dentre elas os pesticidas organoclorados. Este trabalho teve como objetivos avaliar as concentrações dos pesticidas hexaclorobenzeno (HCB), alfa-HCH, ?-HCH, beta-HCH, beta-HCH, heptacloro, heptacloro epóxido, dieldrin, mirex, o,p\'-DDT, p,p\'-DDT, o,p\'-DDE, p,p\'-DDE, o,p\'-DDD e p,p\'-DDD nesta população e compará-las com as encontradas em outros países e determinar fatores associados aos níveis mais elevados destas substâncias. O método analítico utilizado foi de cromatografia a gás. Os resultados deste estudo indicam que a população adulta de São Paulo não está exposta a níveis preocupantes de pesticidas organoclorados, pois dentre os compostos analisados, apenas o beta-HCH e o p,p\'-DDE tiveram um número significante de amostras acima do limite de quantificação, 10,7% e 31,2% das amostras respectivamente. Quando utilizada a metade do limite de quantificação para substituir os valores abaixo do limite de quantificação do método, o valor médio encontrado para o beta-HCH foi de 0,028 ug/dL e para o p,p\'-DDE foi de 0,045 ug/dL. Este estudo propôs dois modelos multivariados para explicar os fatores associados aos compostos beta-HCH e p,p\'-DDE no sangue dos doadores. Segundo o modelo de Regressão Logística Ordinal Multivariado, os fatores associados a níveis mais altos de beta-HCH foram ter idade entre 26 e 45 anos e ser do sexo feminino. Para o p,p\'-DDE os fatores associados a níveis mais altos foram ter idade entre 26 e 45 anos, ser do sexo feminino e ter trabalhado com pesticidas, enquanto receber renda mensal de 3 a 5 salários mínimos e consumir derivados de origem animal uma ou mais vezes por semana foram associados a níveis mais baixos de p,p\'-DDE. Segundo o modelo de Regressão Linear Múltipla, os fatores associados a níveis mais altos de beta-HCH foram o sexo feminino, ter contato prévio com pesticidas na região agrícola, ter trabalhado com pesticidas em campanhas de saúde pública, ter trabalhado em empresas de capacitores ou transformadores, ter trabalhado em indústrias de solventes clorados, ter renda mensal de 3 a 5 salários mínimos, consumo de carnes uma ou duas vezes por semana e consumo de frutos do mar uma ou duas vezes por semana, enquanto consumo frequente de cerveja e ter renda mensal de 1 a 3 salários mínimos foram associado a níveis menores de beta-HCH. Já para o p,p\'-DDE, os fatores associados a níveis mais elevados foram ser do sexo feminino, ser não branco, ter trabalhado com pesticidas e consumir água de fontes que não sejam minerais ou de rede, enquanto o consumo frequente de bebidas alcoólicas foi associado a níveis mais baixos de p,p\'-DDE

Estudo da cinética de crescimento de células de inseto Sf21 e infecção por baculovírus Anticarsia gemmatalis (AgMNPV) para a produção de bioinseticida.

O interesse em estudar o cultivo das células de inseto está relacionado entre outros usos a sua utilização na produção de biopesticidas. Há muitos anos os pesticidas químicos vêm contribuindo no controle de pragas na agricultura. Entretanto, o uso desses compostos prolongadamente tem resultado na seleção de insetos resistentes e em poluição ambiental. Diante disso, torna-se necessário o desenvolvimento e aprimoramento dos bioinseticidas. No Brasil, o baculovírus Anticarsia gemmatalis multiple nucleopolyhedrovirus (AgMNPV) foi o principal agente de controle biológico da praga da soja Anticarsia gemmatalis. Assim, estudos que viabilizem a produção desses vírus in vitro possibilitariam uma produção mais controlada e de melhor qualidade desses biopesticidas. Neste trabalho, investigou-se a suscetibilidade à infecção por AgMNPV de diferentes linhagens celulares de Sf21 e o crescimento dessas células em diferentes sistemas: cultivos em schotts, em spinner e em biorreator, variando-se a idade do inóculo (IA) e a concentração celular inicial (X0). Constatou-se variação no perfil de infecção das linhagens, sendo as linhagens mais adequadas para a produção de bioinseticida as linhagens de Sf21 denominadas EMBRAPA, UFRN e GibcoG, uma vez que estas apresentaram mais do que 40 % das células com poliedros em cultivos em suspensão, enquanto a linhagem denominada GibcoSF teve menos de 2 % das células infectadas com poliedros. Ao se estudar o efeito do número de subcultivos na morfologia e crescimento celular, foi averiguado um aumento no diâmetro de 10 % e no volume de 26 % das células UFRN em relação às células GibcoSF. Além disso, o crescimento das células UFRN foi 49% menor do que das células GibcoSF. Quando realizado o Delineamento Composto Central Rotacional (DCCR) para se analisar o efeito da IA e a X0 na taxa de crescimento específica máxima (?max) e na concentração celular máxima (Xvmax) em cultivos em schott com células UFRN, obteve-se um modelo empírico. Quando analisadas as variáveis IA e X0 separadamente, não foram encontradas diferenças significativas para as respostas Xvmax e ?max em relação a X0. Para a IA, entretanto, obteve-se os resultados mais satisfatórios para os inóculos com IA de 72 e 96 horas: Xvmax de 5,97.106 cel/mL e 5,99.106 cel/mL, e ?max de 0,70 dia-1 e 0,63 dia-1, respectivamente. Nos cultivos em spinner com células UFRN, foi observada a formação de grumos, o que levou a Xvmax de 2,00.106 cel/mL. No cultivo em biorreator com células UFRN, foi obtido um Xvmax de 6,21.106 cel/mL, ?max de 0,70 dia-1, Qo2 na fase exponencial de 67,3 ± 3,6 .10-18 molO2/cel/s, rendimento de glicose em célula igual a 1,0.109 cel/g de glicose e um rendimento de glutamina em células de 3,0.109 cel/mL. Comprovou-se, portanto, a existência de alterações na infecção entre diferentes linhagens de Sf21; a importância do estado fisiológico da célula nos subcultivos, a ocorrência de mudanças no crescimento celular de acordo com os sistemas de cultivo e o efeito do número de subcultivos na morfologia e crescimento de células Sf21.

Formation of brominated pollutants during the pyrolysis and combustion of tetrabromobisphenol A at different temperatures

Tetrabromobisphenol A (TBBPA) is the most widely used brominated flame retardant worldwide. A detailed examination of the degradation products emitted during thermal decomposition of TBBPA is presented in the study. Runs were performed in a laboratory furnace at different temperatures (650 and 800 °C) and in different atmospheres (nitrogen and air). More than one hundred semivolatile compounds have been identified by GC/MS, with special interest in brominated ones. Presence of HBr and brominated light hydrocarbons increased with temperature and in the presence of oxygen. Maximum formation of PAHs is observed at pyrolytic condition at the higher temperature. High levels of 2,4-, 2,6- and 2,4,6- bromophenols were found. The levels of polybrominated dibenzo-p-dioxins and furans have been detected in the ppm range. The most abundant isomers are 2,4,6,8-TeBDF in pyrolysis and 1,2,3,7,8-PeBDF in combustion. These results should be considered in the assessment of thermal treatment of materials containing brominated flame retardants.