ELM-induced transient tungsten melting in the JET divertor

The original goals of the JET ITER-like wall included the study of the impact of an all W divertor on plasma operation (Coenen et al 2013 Nucl. Fusion 53 073043) and fuel retention (Brezinsek et al 2013 Nucl. Fusion 53 083023). ITER has recently decided to install a full-tungsten (W) divertor from the start of operations. One of the key inputs required in support of this decision was the study of the possibility of W melting and melt splashing during transients. Damage of this type can lead to modifications of surface topology which could lead to higher disruption frequency or compromise subsequent plasma operation. Although every effort will be made to avoid leading edges, ITER plasma stored energies are sufficient that transients can drive shallow melting on the top surfaces of components. JET is able to produce ELMs large enough to allow access to transient melting in a regime of relevance to ITER.

Transient W melt experiments were performed in JET using a dedicated divertor module and a sequence of I-P = 3.0 MA/B-T = 2.9 T H-mode pulses with an input power of P-IN = 23 MW, a stored energy of similar to 6 MJ and regular type I ELMs at Delta W-ELM = 0.3 MJ and f(ELM) similar to 30 Hz. By moving the outer strike point onto a dedicated leading edge in the W divertor the base temperature was raised within similar to 1 s to a level allowing transient, ELM-driven melting during the subsequent 0.5 s. Such ELMs (delta W similar to 300 kJ per ELM) are comparable to mitigated ELMs expected in ITER (Pitts et al 2011 J. Nucl. Mater. 415 (Suppl.) S957-64).

Although significant material losses in terms of ejections into the plasma were not observed, there is indirect evidence that some small droplets (similar to 80 mu m) were released. Almost 1 mm (similar to 6 mm(3)) of W was moved by similar to 150 ELMs within 7 subsequent discharges. The impact on the main plasma parameters was minor and no disruptions occurred. The W-melt gradually moved along the leading edge towards the high-field side, driven by j x B forces. The evaporation rate determined from spectroscopy is 100 times less than expected from steady state melting and is thus consistent only with transient melting during the individual ELMs. Analysis of IR data and spectroscopy together with modelling using the MEMOS code Bazylev et al 2009 J. Nucl. Mater. 390-391 810-13 point to transient melting as the main process. 3D MEMOS simulations on the consequences of multiple ELMs on damage of tungsten castellated armour have been performed.

These experiments provide the first experimental evidence for the absence of significant melt splashing at transient events resembling mitigated ELMs on ITER and establish a key experimental benchmark for the MEMOS code.

Tailoring the nonlinear frequency coupling between odd harmonics for the optimisation of charged particle dynamics in capacitively coupled oxygen plasmas

The influence of nonlinear frequency coupling in an oxygen plasma excited by two odd harmonics at moderate pressure is investigated using a numerical model. Through variations in the voltage ratio and phase shift between the frequency components changes in ionization dynamics and sheath voltages are demonstrated. Furthermore, a regime in which the voltage drop across the plasma sheath is minimised is identified. This regime provides a significantly higher ion flux than a single frequency discharge driven by the lower of the two frequencies alone. These operating parameters have potential to be exploited for plasma processes requiring low ion bombardment energies but high ion fluxes. 

Biosensor based toxicity dissection of tannery and associated environmental samples

Kenyan tannery and associated environmental samples were selected for ecotoxicological assessment. A tool-kit of techniques was developed, including whole-cell biosensor and chemical assays. A luminescence based bacterial biosensor (Escherichia coli HB101 pUCD607) (via a multi-copy plasmid) was used for toxicity assessment. Samples were manipulated prior to biosensor interrogation to identify the nature of the toxic contaminants. Untreated samples (before any manipulations) showed a strong toxic effect at the discharge point in comparison to other sampling points. Sparging was used to identify toxicity associated with volatile organics. The toxicity of contaminants, removed by treatment with activated charcoal was identified for all the sampling points except for those upstream of effluent discharges. Filtration identified toxicity associated with suspended solids. Changes in availability of toxic contaminants due to pH adjustment of most samples from the tannery effluent treatment pits were also associated with the extreme pH values (4.0 and 8.0). The approach used has highlighted the complexicity of toxic pollutants in effluent from the tanning industry and the dissection of toxicity points to possible remediation strategies for effluents from the tanning industry.

Investigating Fractured Flow from Orthopaedics to Rehabilitation

Patients often spend time as inpatients in hospitals outside their home area because of the need to access specialist services. If there is a need for ongoing care after the need for specialist care has passed, patients are transferred (or ‘repatriated’) back to the inpatient care of a hospital in their local Health and Social Care Trust. The need for bed space in specialist units means that there is pressure for this transition to occur in a timely way. We investigated the flow of patients through a trauma and orthopaedics unit using the 6M Design® framework and Vitals Charts® in order to investigate concerns about delayed repatriation. We found that repatriation was part of a complex system that had interdependent components. There was considerable variation in the number of discharges (to any destination) by day of week, with a reduction on Saturdays and Sundays. Understanding that the pressure for quicker repatriation was really due to high work-in-progress led us to model the effects of strategies to address the high work-in-progress. We found that, because only a small proportion of patients require repatriation, expediting the repatriation process by one day for each patient would only reduce WIP by an average of 1.6 patients. Reducing the average length of stay for all trauma and orthopaedics inpatients by one day would reduce the WIP by 10 patients, which would make a much greater impact on the problem of high bed occupancy. Though the smooth and timely repatriation of patients to rehabilitation units is desirable, it is unlikely that efforts to achieve this will have a substantial impact on the problem of high WIP, so other strategies will be required. We will model the effects of strategies to reduce variation in daily discharges by the day of week in a future essay.

Mercury (II) removal from aqueous solutions by microporous materials

O Mercúrio é um dos metais pesados mais tóxicos existentes no meio ambiente, é persistente e caracteriza-se por bioamplificar e bioacumular ao longo da cadeia trófica. A poluição com mercúrio é um problema à escala global devido à combinação de emissões naturais e emissões antropogénicas, o que obriga a políticas ambientais mais restritivas sobre a descarga de metais pesados. Consequentemente o desenvolvimento de novos e eficientes materiais e de novas tecnologias para remover mercúrio de efluentes é necessário e urgente. Neste contexto, alguns materiais microporosos provenientes de duas famílias, titanossilicatos e zirconossilicatos, foram investigados com o objectivo de avaliar a sua capacidade para remover iões Hg2+ de soluções aquosas. De um modo geral, quase todos os materiais estudados apresentaram elevadas percentagens de remoção, confirmando que são bons permutadores iónicos e que têm capacidade para serem utilizados como agentes descontaminantes. O titanossilicato ETS-4 foi o material mais estudado devido à sua elevada eficiência de remoção (>98%), aliada à pequena quantidade de massa necessária para atingir essa elevada percentagem de remoção. Com apenas 4 mg⋅dm-3 de ETS-4 foi possível tratar uma solução com uma concentração igual ao valor máximo admissível para descargas de efluentes em cursos de água (50 μg⋅dm-3) e obter água com qualidade para consumo humano (<1.0 μg⋅dm-3), de acordo com a legislação Portuguesa (DL 236/98). Tal como para outros adsorbentes, a capacidade de remoção de Hg2+ do ETS- 4 depende de várias condições experimentais, tais como o tempo de contacto, a massa, a concentração inicial de mercúrio, o pH e a temperatura. Do ponto de vista industrial as condições óptimas para a aplicação do ETS-4 são bastante atractivas, uma vez que não requerem grandes quantidades de material e o tratamento da solução pode ser feito à temperatura ambiente. A aplicação do ETS-4 torna-se ainda mais interessante no caso de efluentes hospitalares, de processos de electro-deposição com níquel, metalúrgica, extracção de minérios, especialmente ouro, e indústrias de fabrico de cloro e soda cáustica, uma vez que estes efluentes apresentam valores de pH semelhantes ao valor de pH óptimo para a aplicação do ETS-4. A cinética do processo de troca iónica é bem descrita pelo modelo Nernst-Planck, enquanto que os dados de equilíbrio são bem ajustados pelas isotérmicas de Langmuir e de Freundlich. Os parâmetros termodinâmicos, ΔG° and ΔH° indicam que a remoção de Hg2+ pelo ETS-4 é um processo espontâneo e exotérmico. A elevada eficiência do ETS-4 é confirmada pelos valores da capacidade de remoção de outros materiais para os iões Hg2+, descritos na literatura. A utilização de coluna de ETS-4 preparada no nosso laboratório, para a remoção em contínuo de Hg2+ confirma que este material apresenta um grande potencial para ser utilizado no tratamento de águas. ABSTRACT: Mercury is one of the most toxic heavy metals, exhibiting a persistent character in the environment and biota as well as bioamplification and bioaccumulation along the food chain. Natural inputs combined with the global anthropogenic sources make mercury pollution a planetary-scale problem, and strict environmental policies on metal discharges have been enforced. The development of efficient new materials and clean-up technologies for removing mercury from effluents is, thus, timely. In this context, in my study, several microporous materials from two families, titanosilicates and zirconosilicates were investigated in order to assess their Hg2+ sorption capacity and removal efficiency, under different operating conditions. In general, almost all microporous materials studied exhibited high removal efficiencies, confirming that they are good ion exchangers and have potential to be used as Hg2+ decontaminant agents. Titanosilicate ETS-4 was the material most studied here, by its highest removal efficiency (>98%) and lowest mass necessary to attain it. Moreover, according with the Portuguese legislation (DL 236/98) it is possible to attain drinking water quality (i.e. [Hg2+]< 1.0 μg⋅dm-3) by treating a solution with a Hg2+ concentration equal to the maximum value admissible for effluents discharges into water bodies (50 μg⋅dm-3), using only 4 mg⋅dm-3 of ETS-4. Even in the presence of major freshwater cations, ETS-4 removal efficiency remains high. Like for other adsorbents, the sorption capacity of ETS-4 for Hg2+ ions is strongly dependent on the operating conditions, such as contact time, mass, initial Hg2+ concentration and solution pH and, to a lesser extent, temperature. The optimum operating conditions found for ETS-4 are very attractive from the industrial point of view because the application of ETS-4 for the treatment of wastewater and/or industrial effluents will not require larges amounts of adsorbent, neither energy supply for temperature adjustments becoming the removal process economically competitive. These conditions become even more interesting in the case of medical institutions liquid, nickel electroplating process, copper smelter, gold ore tailings and chlor-alkali effluents, since no significant pH adjustments to the effluent are necessary. The ion exchange kinetics of Hg2+ uptake is successfully described by the Nernst-Planck based model, while the ion exchange equilibrium is well fitted by both Langmuir and Freundlich isotherms. Moreover, the feasibility of the removal process was confirmed by the thermodynamic parameters (ΔG° and ΔH°) which indicate that the Hg2+ sorption by ETS-4 is spontaneous and exothermic. The higher efficiency of ETS-4 for Hg2+ ions is corroborate by the values reported in literature for the sorption capacity of other adsorbents for Hg2+ ions. The use of an ETS-4 fixed-bed ion exchange column, manufactured in our laboratory, in the continuous removal of Hg2+ ions from solutions confirms that this titanosilicate has potential to be used in industrial water treatment.

Efeitos da toxicidade por metais pesados em Rhizobium leguminosarum bv. trifolii: diversidade e resposta de população isoladas de uma mina de chumbo

Nas últimas décadas verificou-se um aumento da contaminação dos solos com metais pesados resultante de processos antropogénicos. As descargas de efluentes industriais, a actividade mineira e a aplicação de lamas residuais e de fertilizantes são as principais fontes de metais pesados. Em certas regiões, a acumulação destes elementos nos solos tem atingido níveis preocupantes para o equilíbrio dos ecossistemas. Vários estudos têm demonstrado que os metais influenciam os microrganismos afectando adversamente o seu crescimento, morfologia e actividades bioquímicas resultando num decréscimo da biomassa e diversidade. Entre os microrganismos do solo, as bactérias pertencentes ao género Rhizobium têm um elevado interesse científico, económico e ecológico devido à sua capacidade para fixar azoto. Deste modo, o trabalho desenvolvido ao longo desta tese incidiu sobre o efeito da toxicidade imposta pelos metais nas bactérias fixadoras de azoto, em particular em Rhizobium leguminosarum bv. trifolii e teve como principais objectivos: determinar o efeito dos metais pesados na sobrevivência e na capacidade de fixar azoto dos isolados de rizóbio; avaliar a influência dos metais na diversidade das populações de rizóbio isoladas de solos contaminados; determinar os níveis de tolerância do rizóbio a diferentes metais e analisar a resposta ao stresse oxidativo imposto pelo cádmio. A Mina do Braçal foi o local de estudo escolhido uma vez que os seus solos estão muito contaminados com metais em resultado da extracção de minério durante mais de 100 anos. Foram escolhidos 3 solos com diferentes graus de contaminação, o solo BC com concentrações reduzidas de metais, escolhido por estar numa zona já fora da mina e designado por solo controlo e os solos BD e BA considerados medianamente e muito contaminados, respectivamente. O Pb e o Cd foram os metais predominantes nestes solos, assim como o metalóide As, cujas concentrações ultrapassaram largamente os limites previstos na lei. Sendo as enzimas do solo boas indicadoras da qualidade do mesmo, foi determinada a actividade de algumas como a desidrogenase (DHA) e a catalase (CAT). Ambas as enzimas correlacionaramse negativamente com as concentrações de metais nos solos. A dimensão das populações indígenas de rizóbio nos solos contaminados (BD e BA) foi bastante baixa, 9,1 bactérias g-1 de solo e 7,3 bactérias g-1 de solo, respectivamente, quando em comparação com a população do solo BC (4,24x104 bactérias g-1 de solo). Estes resultados parecem estar relacionados com o elevado conteúdo em metais e com o pH ácido dos solos. A capacidade simbiótica também foi afectada pela presença de metais, uma vez que os isolados originários do solo BD mostraram menor capacidade em fixar azoto do que os isolados do solo controlo. A diversidade das populações de rizóbio foi determinada com recurso à análise dos perfis de plasmídeos, perfis de REP e ERIC-PCR de DNA genómico e perfis de proteínas e lipopolissacarídeos. No conjunto dos 35 isolados analisados foram identificados 11 plasmídeos com pesos moleculares entre 669 kb e 56 kb. Embora a incidência de plasmídeos tenha sido superior nos isolados do solo BC verificou-se maior diversidade plasmídica na população isolada do solo BD. Resultados similares foram obtidos com os perfis de REP e ERIC-PCR e perfis de proteínas, que indicaram maior diversidade nas populações dos solos contaminados (BD e BA), contrariamente ao verificado por outros autores. O grau de tolerância aos metais pesados e ao arsénio dos vários isolados testados dependeu do metal e do local de origem. No geral, os isolados do solo BD mostraram maior tolerância aos metais do que os isolados do solo controlo, o que está de acordo com o esperado uma vez que geralmente as populações dos locais contaminados são mais tolerantes. Contudo, os isolados do local mais contaminado (BA) foram muito tolerantes apenas ao chumbo mostrando-se sensíveis aos restantes metais. A inoculação dos solos BC, BD e BA após irradiação com estirpes seleccionadas de rizóbio permitiu avaliar a sua sobrevivência ao longo de 12 meses em condições mais realistas. Verificou-se que após um decréscimo inicial, os isolados inoculados no solo BC conseguiram recuperar a dimensão das suas populações para números similares aos inicialmente introduzidos, contrariamente ao verificado no solo BD onde o número de rizóbios decresceu ao longo dos 12 meses. As condições adversas do solo BA apenas permitiram a sobrevivência de 4 isolados até aos 3 meses e apenas dois deles conseguiram sobreviver após 12 meses, designadamente C 3-1 e A 17-3. Estes isolados possuem um plasmídeo de 669 kb que poderá estar na base da sobrevivência destas estirpes. Por outro lado, o último isolado é originário do solo contaminado e por isso estará também mais adaptado a sobreviver às elevadas concentrações de Pb existentes no solo BA. Por fim, constatou-se que o cádmio, um dos metais presente em concentrações mais elevadas nos solos em estudo, é um indutor de stresse oxidativo nos isolados de rizóbio menos tolerantes o que foi confirmado pelo aumento de ROS e danos celulares ao nível dos lípidos.

Modelling the Minho river plume intrusion into the rias baixas

The Minho River, situated 30 km south of the Rias Baixas is the most important freshwater source flowing into the Western Galician Coast (NW of the Iberian Peninsula). This discharge is important to determine the hydrological patterns adjacent to its mouth, particularly close to the Galician coastal region. The buoyancy generated by the Minho plume can flood the Rias Baixas for long periods, reversing the normal estuarine density gradients. Thus, it becomes important to analyse its dynamics as well as the thermohaline patterns of the areas affected by the freshwater spreading. Thus, the main aim of this work was to study the propagation of the Minho estuarine plume to the Rias Baixas, establishing the conditions in which this plume affects the circulation and hydrographic features of these coastal systems, through the development and application of the numerical model MOHID. For this purpose, the hydrographic features of the Rias Baixas mouths were studied. It was observed that at the northern mouths, due to their shallowness, the heat fluxes between the atmosphere and ocean are the major forcing, influencing the water temperature, while at the southern mouths the influence of the upwelling events and the Minho River discharge were more frequent. The salinity increases from south to north, revealing that the observed low values may be caused by the Minho River freshwater discharge. An assessment of wind data along the Galician coast was carried out, in order to evaluate the applicability of the study to the dispersal of the Minho estuarine plume. Firstly, a comparative analysis between winds obtained from land meteorological stations and offshore QuikSCAT satellite were performed. This comparison revealed that satellite data constitute a good approach to study wind induced coastal phenomena. However, since the numerical model MOHID requires wind data with high spatial and temporal resolution close to the coast, results of the forecasted model WRF were added to the previous study. The analyses revealed that the WRF model data is a consistent tool to obtain representative wind data near the coast, showing good results when comparing with in situ wind observations from oceanographic buoys. To study the influence of the Minho buoyant discharge influence on the Rias Baixas, a set of three one-way nested models was developed and implemented, using the numerical model MOHID. The first model domain is a barotropic model and includes the whole Iberian Peninsula coast. The second and third domains are baroclinic models, where the second domain is a coarse representation of the Rias Baixas and adjacent coastal area, while the third includes the same area with a higher resolution. A bi-dimensional model was also implemented in the Minho estuary, in order to quantify the flow (and its properties) that the estuary injects into the ocean. The chosen period for the Minho estuarine plume propagation validation was the spring of 1998, since a high Minho River discharge was reported, as well as favourable wind patterns to advect the estuarine plume towards the Rias Baixas, and there was field data available to compare with the model predictions. The obtained results show that the adopted nesting methodology was successful implemented. Model predictions reproduce accurately the hydrodynamics and thermohaline patterns on the Minho estuary and Rias Baixas. The importance of the Minho river discharge and the wind forcing in the event of May 1998 was also studied. The model results showed that a continuous moderate Minho River discharge combined with southerly winds is enough to reverse the Rias Baixas circulation pattern, reducing the importance of the occurrence of specific events of high runoff values. The conditions in which the estuarine plume Minho affects circulation and hydrography of the Rias Baixas were evaluated. The numerical results revealed that the Minho estuarine plume responds rapidly to wind variations and is also influenced by the bathymetry and morphology of the coastline. Without wind forcing, the plume expands offshore, creating a bulge in front of the river mouth. When the wind blows southwards, the main feature is the offshore extension of the plume. Otherwise, northward wind spreads the river plume towards the Rias Baixas. The plume is confined close to the coast, reaching the Rias Baixas after 1.5 days. However, for Minho River discharges higher than 800 m3 s-1, the Minho estuarine plume reverses the circulation patterns in the Rias Baixas. It was also observed that the wind stress and Minho River discharge are the most important factors influencing the size and shape of the Minho estuarine plume. Under the same conditions, the water exchange between Rias Baixas was analysed following the trajectories particles released close to the Minho River mouth. Over 5 days, under Minho River discharges higher than 2100 m3 s-1 combined with southerly winds of 6 m s-1, an intense water exchange between Rias was observed. However, only 20% of the particles found in Ria de Pontevedra come directly from the Minho River. In summary, the model application developed in this study contributed to the characterization and understanding of the influence of the Minho River on the Rias Baixas circulation and hydrography, highlighting that this methodology can be replicated to other coastal systems.

Coupling anchovy eggs and hydrodynamic model as an assessement tool for estuarine ecohydrological management

Nitrate and urban waste water directives have raised the need for a better understanding of coastal systems in European Union. The incorrect application of these directives can lead to important ecological or social penalties. In the paper this problem is addressed to Ria Formosa Coastal Lagoon. Ria Formosa hosts a Natural Park, important ports of the southern Portuguese coast and significant bivalve aquaculture activity. Four major urban waste water treatment plants discharging in the lagoon are considered in this study. Its treatment level must be selected, based on detailed information from a monitoring program and on a good knowledge of the processes determining the fate of the material discharged in the lagoon. In this paper the results of a monitoring program and simulations using a coupled hydrodynamic and water quality / ecological model, MOHID, are used to characterise the system and to understand the processes in Ria Formosa. It is shown that the water residence time in most of the lagoon is quite low, of the order of days, but it can be larger in the upper parts of the channels where land generated water is discharged. The main supply of nutrients to the lagoon comes from the open sea rather than from the urban discharges. For this reason the characteristics and behaviour of the general lagoon contrasts with the behaviour of the upper reaches of the channels where the influence of the waste water treatment plants are high. In this system the bottom mineralization was found to be an important mechanism, and the inclusion of that process in the model was essential to obtain good results.

EU water framework directive: will the nitrate load reduction from diffuse sources produce the same results in all estuaries?

The impact of urban waste-water and non-point nitrate discharges in estuarine and near-shore coastal waters are analyzed. The study is focused on the effects of applying the European directives 91/271/EEC and 91/676/EEC to these systems. 4 Portuguese estuaries and two coastal lagoons with different characteristics are studied. A modelling system is applied and calibrated in each system. Three nitrate load scenarios are examined. It is shown that the morphologic and hydrodynamic characteristics of the domain largely control the ecological processes in these systems. The primary production limitation factors are split into “biologic” and “hydrodynamic” components. The physical limitation due to hydrodynamic and residence time is the most important factor. The combined limitation of “biologic” factors (temperature, light and nutrients availability) control productivity only in the systems where physical limitation is not important.

Hydroinformatics based decision.making integrating modelling, sampling and profiling: the Ria Formosa case

A Waste Water monitoring program aiming to help decision making is presented. The program includes traditional and inboard sensor sampling, hydrodynamic and water quality modeling and a GIS based database to help the decision making of manager authorities. The focus is in the quality of waters receiving discharges from Waste Water Treatment Plants. Data was used to feed model simulations and produce hydrodynamic, effluent dispersion and ecological results. The system was then used to run different scenarios of discharge flow, concentration and location. The results enable to access the current water quality state of the lagoon and are being used as a decision making tool by the waste water managers in the evaluation phase of the treatment plant project to decide the location and the level of treatment of the discharge.

The function and future of the LOICS basins approach in promoting integrated coastal zone & watershed management with an emphasis on developing countries

Dissertação de Mestrado, Gestão da Água e da Costa, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2010

Primary production in systems subject to natural and anthropogenic eutrophication

Tese dout., Química, Universidade do Algarve, 2005

Simulation of economic benefits achieved by water quality improvement for recreational and professional users, within the SPICOSSA SSA (SPICOSSA System Approach) 11 - Guadiana estuary ecosystem sic

Dissertação de Mestrado, Gestão da Água e da Costa, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2010