(Table 1) Chemical and isotopic compositions of rudist aragonite and magnesian calcite cements from ODP Hole 144-877A

The classic paleotemperature record based on d18O data from pelagic foraminiferal calcite suggests that equatorial sea-surface temperatures during the Maastrichtian (~12-20°C) were much cooler than today (~27-29°C). Such cool equatorial temperatures contradict basic theories of tropical atmospheric and ocean dynamics. We report d18O data from remarkably well preserved rudist aragonite and magnesian calcite cements of Maastrichtian age (~69+/-1 Ma) from the carbonate platform of Wodejebato guyot in the western Pacific. These data suggest that equatorial sea-surface temperatures in the Maastrichtian (best estimate ~27-32°C) were at least as warm as today. This finding helps reconcile the geologic d18O record with ocean-atmospheric dynamic theory and implies a reduction in the poleward heat flux required by global climate simulations of greenhouse conditions.

Mejora del comportamiento térmico de los morteros de cal aditivados y su empleo en la rehabilitación de inmuebles = Improvement of thermal behaviour of additived lime mortars and their use in rehabilitation of buildings

La envolvente de la edificación es la responsable de equilibrar el intercambio energético entre el interior y el exterior, por lo tanto cualquier actuación encaminada a la reducción del consumo energético ha de establecer, como uno de sus objetivos prioritarios, la mejora del comportamiento de la misma. Las edificaciones anteriores a 1940 constituyen la mayor parte de las existentes en áreas rurales y centros urbanos. En ellas, la repercusión de la fachada sobre las transmitancias globales pone de manifiesto la necesidad de intervención. Sin embargo, su elevada inercia térmica y los importantes saltos térmicos característicos de gran parte de España plantean la importancia de que aquélla se efectúe por el exterior. A tal respecto, la falta de disponibilidad de espesor suficiente para implantar sistemas tipo SATE deriva en que, frecuentemente, la única solución viable sea la de aislar por el interior perdiendo con ello la capacidad de acumulación térmica del muro y con el asociado riesgo de condensaciones. La amplia tradición en el empleo de revestimientos, especialmente en base de cal, permiten que éstos sean utilizados no sólo como elemento estético o de protección de la obra de fábrica antigua sino también para la mejora del comportamiento térmico del soporte, si se aprovecha el mecanismo de transmisión térmica por radiación. Éste es el objetivo de la presente Tesis Doctoral en la que se estudia la modificación de las propiedades radiantes de los morteros de revestimiento para la mejora de la eficiencia energética de las construcciones históricas, principalmente las constituidas por muros monolíticos, aunque podría ser de aplicación a otro tipo de construcciones compuestas por diversas capas. Como punto de partida, se estudió y revisó la documentación disponible sobre las investigaciones de las tres áreas científico-tecnológicas que convergen en la Tesis Doctoral: rehabilitación, material y comportamiento térmico, a partir de lo cual se comprobó la inexistencia de estudios similares al objeto de la presente Tesis Doctoral. Complementariamente, se analizaron los revestimientos en lo concerniente a los materiales que los constituyen, la composición de las mezclas y características de cada una de las capas así como al enfoque que, desde el punto de vista térmico, se estimaba más adecuado para la obtención de los objetivos propuestos. Basándonos en dichos análisis, se preseleccionaron ochenta materiales que fueron ensayados en términos de reflectancia y emisividad para elegir cuatro con los que se continuó la investigación. Éstos, junto con la cal elegida para la investigación y el árido marmóreo característico de la última capa de revestimiento, fueron caracterizados térmicamente, de forma pormenorizada, así como química y físicamente. Los fundamentos teóricos y los estudios preliminares desarrollados con distintos materiales, en estado fresco y endurecido, fueron empleados en la dosificación de componentes de las mezclas, en dos proporciones distintas, para el estudio del efecto del agregado. Éstas se ensayaron en estado fresco, para comprobar su adecuación de puesta en obra y prever su VI adherencia al soporte, así como en estado endurecido a 28 y 90 días de curado, para conocer las propiedades que permitieran prever su compatibilidad con aquél y estimar el alcance de la reducción de transferencias térmicas lograda. Además, se estudiaron las características generales de las mezclas que sirvieron para establecer correlaciones entre distintas propiedades y entender los resultados mecánicos, físicos (comportamiento frente al agua) y energéticos. Del estudio conjunto de las distintas propiedades analizadas se propusieron dos mezclas, una blanca y otra coloreada, cuyas características permiten garantizar la compatibilidad con la obra de fábrica antigua, desde el punto de vista físico y mecánico, y preservar la autenticidad de los revestimientos, en cuanto a la técnica de aplicación tradicional en sistemas multicapa. El comportamiento térmico de las mismas, sobre una obra de fábrica de 40 cm de espesor, se estimó, en estado estacionario y pseudo-transitorio, demostrándose reducciones del flujo térmico entre 16-48%, en condiciones de verano, y entre el 6-11%, en invierno, en función de la coloración y de la rugosidad de la superficie, en comparación con el empleo de la mezcla tradicional. Por lo que, se constata la viabilidad de los materiales compuestos propuestos y su adecuación al objetivo de la investigación. VII ABSTRACT The envelope is responsible for balancing the energy exchange between the inside and outside in buildings. For this reason, any action aimed at reducing energy consumption must establish, as one of its key priorities, its improvement. In rural areas and urban centers, most of the constructions were built before 1940. In them, the impact of the façade on the global transmittance highlights the need for intervention. However, its high thermal inertia and fluctuation of temperatures in the majority of Spain bring up that it should be placed outside the insulation. In this regard, the lack of availability of enough thickness to implement systems such as ETICS results in that often the only viable solution is to isolate the interior, losing thereby the wall’s heat storage capacity with the associated risk of condensation. The tradition in the use of renders, especially lime-based, allows us to use them not only as an aesthetic element or to protect the ancient masonry, but also for improved thermal performance of the support by taking advantage of the heat transfer mechanism by radiation. This is the aim of this Doctoral Thesis in which the modification of the radiative properties of lime mortars for renders to improve the energy efficiency of historic buildings, mainly composed of monolithic walls, is studied, although it could be applied to other structures composed of several layers. As a starting point, the available literature in the three scientific-technological areas that converge at the Doctoral Thesis: rehabilitation, material and thermal behaviour, was reviewed, and confirmed the absence of researches similar to this Doctoral Thesis. Additionally, the renders were studied with regard to the materials that constitute them, the composition of the mixtures and the characteristics of each layer, as well as to the approach which, from a thermal point of view, was deemed the most suitable for achieving the objectives sets. Based on thre aforementioned analysis, eighty materials tested in terms of reflectance and emissivity were pre-selected, to choose four with which the research was continued. Common marble sand, used in the last layer of the renders, together with the appointed materials and hydrated lime were characterized thermally, in detail, as well as chemically and physically. The theoretical bases and preliminary studies with different materials, in fresh and hardened state, were used in the dosage of the composition of the mixtures. In order to study their effect they were used in two different proportions, that is, ten mixtures in total. These were tested in their fresh state to evaluate their setting-up suitability and foresee their adhesion to the support, as well as in their hardened state, at 28 and 90 days of curing, to establish the properties which enabled us to anticipate their compatibility with the old masonry walls and estimate the scope of the reduction of heat transfers achieved. In addition, the general characteristics of the mixtures used to establish correlations and to understand the mechanical, physical and energy results were studied. Two mixtures, one white and one colored, were proposed as the result of the different properties analysed, whose characteristics allow the guarantee of mechanical and physical compatibility VIII with the old masonry and preserve the authenticity of the renders. The thermal behavior of both, applied on a masonry wall 40 cm thick, was estimated at a steady and pseudo-transient state, with heat flow reductions between 16-48% during summertime and 6-11% during wintertime, depending on the color and surface roughness, compared to the use of the traditional mixture. So, the viability of the proposed composite materials and their fitness to the aim of the research are established.

Improving automatic detection of obstructive sleep apnea through nonlinear analysis of sustained speech

We present a novel approach for the detection of severe obstructive sleep apnea (OSA) based on patients' voices introducing nonlinear measures to describe sustained speech dynamics. Nonlinear features were combined with state-of-the-art speech recognition systems using statistical modeling techniques (Gaussian mixture models, GMMs) over cepstral parameterization (MFCC) for both continuous and sustained speech. Tests were performed on a database including speech records from both severe OSA and control speakers. A 10 % relative reduction in classification error was obtained for sustained speech when combining MFCC-GMM and nonlinear features, and 33 % when fusing nonlinear features with both sustained and continuous MFCC-GMM. Accuracy reached 88.5 % allowing the system to be used in OSA early detection. Tests showed that nonlinear features and MFCCs are lightly correlated on sustained speech, but uncorrelated on continuous speech. Results also suggest the existence of nonlinear effects in OSA patients' voices, which should be found in continuous speech.

Análisis de la viabilidad técnica de las aerobombas para el riego localizado

Actualmente la agricultura cubana, por ser un sector estratégico en la economía del país, incorpora en su desarrollo y gestión las energías renovables como criterio básico para su viabilidad futura. Sin embargo existen un número de problemas que limitan el desarrollo de estas fuentes energéticas en Cuba, entre los que se encuentran el conocimiento incompleto de su potencial de utilización. Por esta razón, la presente investigación tiene como objetivo la maximización de la superficie regada de un cultivo dado y la determinación del volumen de regulación mínimo, usando una aerobomba tipo, en condiciones ambientales dadas. Se desarrolla una metodología para predecir la máxima potencialidad de las aerobombas para un sistema de riego localizado, basada en el cálculo del balance diario entre las necesidades de agua del cultivo y la disponibilidad de agua. Mediante un ejemplo que ilustra el uso de esta metodología en el cultivo de tomate (Solanum lycopersicum L. var. FL - 5) bajo invernadero en Ciego de Ávila, Cuba, se hace una descripción de los elementos de la instalación propuesta para el suministro de agua por parte de la aerobomba. Se estudiaron varios factores, tales como la serie de velocidad del viento trihoraria ( h V3 , m s-1) para un año medio de viento y para un año medio de poco viento; el caudal suministrado por la aerobomba en función de la altura de elevación ( H , m); y la evapotranspiración diaria del cultivo en invernadero en función de la fecha de siembra. A partir de los factores mencionados se determinaron los volúmenes de agua mensuales necesarios para el riego ( r D , m3 ha-1), la capacidad del depósito de almacenamiento ( dep. V , m3), así como las áreas máximas regables ( r A , ha) para cada variante. Los resultados muestran que el período óptimo de bombeo eólico para el riego del cultivo de tomate en invernadero bajo las condiciones ambientales estudiadas es de noviembre a febrero, y que los factores que más influyen en la superficie que se puede regar con el bombeo eólico son la fecha de plantación y el volumen de depósito. Abstract Currently Cuban agriculture, as a strategic sector in the economy of the country, incorporates in its development and renewable energy management as a basic criterion for its future viability. However, there are a number of problems that limit the development of these energy sources in Cuba, among which are the incomplete knowledge of their potential use. For this reason, this research aims at maximizing the irrigated area of a given culture and determination of minimum control volume, using a type Windpump in given environmental conditions. We develop a methodology to predict the maximum potential of windmills for irrigation system, based on the daily balance calculation between the crop water needs and water availability. Through an example that illustrates the use of this methodology in the cultivation of tomato (Solanum lycopersicum L. var. FL - 5) under greenhouse in Ciego de Avila, Cuba, is a description of the elements of the proposed facility to supply water from the windmill. We studied several factors such as the number of trihoraria wind speed ( h V3 , m s- 1) for an average wind year and an average year with little wind, the flow supplied by the windmill depending on the lift height ( H , m) and daily crop evapotranspiration in greenhouse based on planting date. From the above factors were determined monthly water volumes needed for irrigation ( r D , m3 ha-1), the storage tank capacity ( dep. V , m3) and peak areas irrigated ( r A , ha) for each variant. The results show that the optimal period wind pumping for irrigation of greenhouse tomato crop under the environmental conditions studied is from November to February, and that the factors that influence the surface that can be irrigated with wind pumping are planting date and amount of deposit.

SolarPaces 2013: Innovations on direct steam generation in linear fresnel collectors

Direct Steam Generation (DSG) in Linear Fresnel (LF) solar collectors is being consolidated as a feasible technology for Concentrating Solar Power (CSP) plants. The competitiveness of this technology relies on the following main features: water as heat transfer fluid (HTF) in Solar Field (SF), obtaining high superheated steam temperatures and pressures at turbine inlet (500ºC and 90 bar), no heat tracing required to avoid HTF freezing, no HTF degradation, no environmental impacts, any heat exchanger between SF and Balance Of Plant (BOP), and low cost installation and maintenance. Regarding to LF solar collectors, were recently developed as an alternative to Parabolic Trough Collector (PTC) technology. The main advantages of LF are: the reduced collector manufacturing cost and maintenance, linear mirrors shapes versus parabolic mirror, fixed receiver pipes (no ball joints reducing leaking for high pressures), lower susceptibility to wind damages, and light supporting structures allowing reduced driving devices. Companies as Novatec, Areva, Solar Euromed, etc., are investing in LF DSG technology and constructing different pilot plants to demonstrate the benefits and feasibility of this solution for defined locations and conditions (Puerto Errado 1 and 2 in Murcia Spain, Lidellin Newcastle Australia, Kogran Creek in South West Queensland Australia, Kimberlina in Bakersfield California USA, Llo Solar in Pyrénées France,Dhursar in India,etc). There are several critical decisions that must be taken in order to obtain a compromise and optimization between plant performance, cost, and durability. Some of these decisions go through the SF design: proper thermodynamic operational parameters, receiver material selection for high pressures, phase separators and recirculation pumps number and location, pipes distribution to reduce the amount of tubes (reducing possible leaks points and transient time, etc.), etc. Attending to these aspects, the correct design parameters selection and its correct assessment are the main target for designing DSG LF power plants. For this purpose in the recent few years some commercial software tools were developed to simulatesolar thermal power plants, the most focused on LF DSG design are Thermoflex and System Advisor Model (SAM). Once the simulation tool is selected,it is made the study of the proposed SFconfiguration that constitutes the main innovation of this work, and also a comparison with one of the most typical state-of-the-art configuration. The transient analysis must be simulated with high detail level, mainly in the BOP during start up, shut down, stand by, and partial loads are crucial, to obtain the annual plant performance. An innovative SF configurationwas proposed and analyzed to improve plant performance. Finally it was demonstrated thermal inertia and BOP regulation mode are critical points in low sun irradiation day plant behavior, impacting in annual performance depending on power plant location.

Fracture behaviour of notched round bars made of PMMA subjected to torsion at -60 °C

This paper presents seventy new experimental results from PMMA notched specimens tested under torsion at 60 C. The notch root radius ranges from 0.025 to 7.0 mm. At this temperature the non-linear effects previously observed on specimens of the same material tested at room temperature strongly reduce. The averaged value of the strain energy density over a control volume is used to assess the critical loads to failure. The radius of the control volume and the critical strain energy density are evaluated a priori by using in combination the mode III critical stress intensity factor from cracked-like specimens and the critical stress to failure detected from semicircular notches with a large notch root radius

Analysis of the geometric altimetry to support aircraft optimal trajectories within the future 4d trajectory management

Over the past few years, the common practice within air traffic management has been that commercial aircraft fly by following a set of predefined routes to reach their destination. Currently, aircraft operators are requesting more flexibility to fly according to their prefer- ences, in order to achieve their business objectives. Due to this reason, much research effort is being invested in developing different techniques which evaluate aircraft optimal trajectory and traffic synchronisation. Also, the inefficient use of the airspace using barometric altitude overall in the landing and takeoff phases or in Continuous Descent Approach (CDA) trajectories where currently it is necessary introduce the necessary reference setting (QNH or QFE). To solve this problem and to permit a better airspace management born the interest of this research. Where the main goals will be to evaluate the impact, weakness and strength of the use of geometrical altitude instead of the use of barometric altitude. Moreover, this dissertation propose the design a simplified trajectory simulator which is able to predict aircraft trajectories. The model is based on a three degrees of freedom aircraft point mass model that can adapt aircraft performance data from Base of Aircraft Data, and meteorological information. A feature of this trajectory simulator is to support the improvement of the strategic and pre-tactical trajectory planning in the future Air Traffic Management. To this end, the error of the tool (aircraft Trajectory Simulator) is measured by comparing its performance variables with actual flown trajectories obtained from Flight Data Recorder information. The trajectory simulator is validated by analysing the performance of different type of aircraft and considering different routes. A fuel consumption estimation error was identified and a correction is proposed for each type of aircraft model. In the future Air Traffic Management (ATM) system, the trajectory becomes the fundamental element of a new set of operating procedures collectively referred to as Trajectory-Based Operations (TBO). Thus, governmental institutions, academia, and industry have shown a renewed interest for the application of trajectory optimisation techniques in com- mercial aviation. The trajectory optimisation problem can be solved using optimal control methods. In this research we present and discuss the existing methods for solving optimal control problems focusing on direct collocation, which has received recent attention by the scientific community. In particular, two families of collocation methods are analysed, i.e., Hermite-Legendre-Gauss-Lobatto collocation and the pseudospectral collocation. They are first compared based on a benchmark case study: the minimum fuel trajectory problem with fixed arrival time. For the sake of scalability to more realistic problems, the different meth- ods are also tested based on a real Airbus 319 El Cairo-Madrid flight. Results show that pseudospectral collocation, which has shown to be numerically more accurate and computa- tionally much faster, is suitable for the type of problems arising in trajectory optimisation with application to ATM. Fast and accurate optimal trajectory can contribute properly to achieve the new challenges of the future ATM. As atmosphere uncertainties are one of the most important issues in the trajectory plan- ning, the final objective of this dissertation is to have a magnitude order of how different is the fuel consumption under different atmosphere condition. Is important to note that in the strategic phase planning the optimal trajectories are determined by meteorological predictions which differ from the moment of the flight. The optimal trajectories have shown savings of at least 500 [kg] in the majority of the atmosphere condition (different pressure, and temperature at Mean Sea Level, and different lapse rate temperature) with respect to the conventional procedure simulated at the same atmosphere condition.This results show that the implementation of optimal profiles are beneficial under the current Air traffic Management (ATM).

The Superoxide Synthases of Rose Cells1 : Comparison of Assays

In an effort to identify the enzymatic mechanism responsible for the synthesis of reactive oxygen species produced during the hypersensitive response, preparations of rose (Rosa damascena) cell plasma membranes, partially solubilized plasma membrane protein, and cytosol were assayed for the NADH- and NADPH-dependent synthesis of superoxide using assays for the reduction of cytochrome c (Cyt c), assays for the reduction of nitroblue tetrazolium, and assays for the chemiluminescence of N,N′-dimethyl-9,9′-biacridium dinitrate (lucigenin). Each assay ascribed the highest activity to a different preparation: the Cyt c assay to cytosol, the nitroblue tetrazolium assay to plasma membrane, and the lucigenin assay to the partially solubilized plasma membrane protein (with NADH). This suggests that no two assays measure the same set of enzymes and that none of the assays is suitable for comparisons of superoxide synthesis among different cell fractions. With the plasma membrane preparation, the presence of large amounts of superoxide-dismutase-insensitive Cyt c reductase confounded attempts to use Cyt c to measure superoxide synthesis. With the partially solubilized membrane protein, direct reduction of lucigenin probably contributed to the chemiluminescence. Superoxide synthesis detected with lucigenin should be confirmed by superoxide-dismutase-sensitive Cyt c reduction.

The NAD(P)H Dehydrogenase in Barley Thylakoids Is Photoactivatable and Uses NADPH as well as NADH1

An improved light-dependent assay was used to characterize the NAD(P)H dehydrogenase (NDH) in thylakoids of barley (Hordeum vulgare L.). The enzyme was sensitive to rotenone, confirming the involvement of a complex I-type enzyme. NADPH and NADH were equally good substrates for the dehydrogenase. Maximum rates of activity were 10 to 19 μmol electrons mg−1 chlorophyll h−1, corresponding to about 3% of linear electron-transport rates, or to about 40% of ferredoxin-dependent cyclic electron-transport rates. The NDH was activated by light treatment. After photoactivation, a subsequent light-independent period of about 1 h was required for maximum activation. The NDH could also be activated by incubation of the thylakoids in low-ionic-strength buffer. The kinetics, substrate specificity, and inhibitor profiles were essentially the same for both induction strategies. The possible involvement of ferredoxin:NADP+ oxidoreductase (FNR) in the NDH activity could be excluded based on the lack of preference for NADPH over NADH. Furthermore, thenoyltrifluoroacetone inhibited the diaphorase activity of FNR but not the NDH activity. These results also lead to the conclusion that direct reduction of plastoquinone by FNR is negligible.

Transgenic expression of PML/RARalpha impairs myelopoiesis.

The translocation found in acute promyelocytic leukemia rearranges the promyelocytic leukemia gene (PML) on chromosome 15 with the retinoic acid receptor alpha (RARalpha) on chromosome 17. This yields a fusion transcript, PML/RARalpha, a transcription factor with reported dominant negative functions in the absence of hormone. Clinical remissions induced with all-trans retinoic acid (RA) treatment in acute promyelocytic leukemia are linked to PML/RARalpha expression in leukemic cells. To evaluate the PML/RARalpha role in myelopoiesis, transgenic mice expressing PML/RARalpha were engineered. A full-length PML/RARalpha cDNA driven by the CD11b promoter was expressed in transgenic mice. Expression was confirmed in the bone marrow with a reverse transcription PCR assay. Basal total white blood cell and granulocyte counts did not appreciably differ between PML/RARalpha transgenic and control mice. Cell sorter analysis of CD11b+ bone marrow cells revealed similar CD11b+ populations in transgenic and control mice. However, in vitro clonal growth assays performed on peripheral blood from transgenic versus control mice revealed a marked reduction of myeloid progenitors, especially in those responding to granulocyte/ macrophage colony-stimulating factor. Granulocyte/macrophage colony-stimulating factor and kit ligand cotreatment did not overcome this inhibition. Impaired myelopoiesis in vivo was shown by stressing these mice with sublethal irradiation. Following irradiation, PML/RARalpha transgenic mice, as compared with controls, more rapidly depressed peripheral white blood cell and granulocyte counts. As expected, nearly all control mice (94.4%) survived irradiation, yet this irradiation was lethal to 45.8% of PML/RARalpha transgenic mice. Lethality was associated with more severe leukopenia in transgenic versus control mice. Retinoic acid treatment of irradiated PML/RARalpha mice enhanced granulocyte recovery. These data suggest that abnormal myelopoiesis due to PML/RARalpha expression is an early event in oncogenic transformation.

Abrasão-corrosão em corpos moedores na moagem de minério de ferro.

O desgaste de corpos moedores constitui um custo importante na indústria mineral, que depende da operação de cominuição para promover a liberação das espécies minerais e produzir concentrados. Embora se conheça alguns dos mecanismos individuais que afetam o desgaste, a interação entre eles num sistema tão complexo quanto um moinho ainda precisa ser melhor entendido. Este trabalho avaliou o efeito da corrosão no desgaste de bolas de aço e de ferro fundido branco de alto cromo durante a moagem de minério de ferro, através de ensaios eletroquímicos e de desgaste em moinho de laboratório. Foi feita uma alteração no modo tradicional de realização do ensaio de polarização potenciodinâmica, utilizando polpa de minério de ferro a 70% de sólidos (em peso) como eletrólito. As curvas de polarização obtidas foram compatíveis com os resultados de desgaste, de modo que as curvas correspondentes aos metais na condição mais ativa estavam associadas às menores taxas de desgaste nos ensaios de moagem em laboratório, demonstrando que os ensaios de polarização realizados podem ser utilizados como indicativo do comportamento do metal na moagem de minério de ferro. Sobretudo, os testes demonstraram que o desgaste das bolas de aço é devido, principalmente, à abrasão, já que uma pequena diferença, de apenas 8%, foi observada nas taxas de desgaste nas condições avaliadas (polpa no pH 5 e pH 8). Por outro lado, as bolas de ferro fundido branco de alto cromo, que são mais caras, são mais propensas a resistir ao desgaste em polpa ácida, em que a taxa de desgaste foi 40% menor que a determinada em pH 8.