ENVIRONMENTAL EXPOSURES AND LUNG CANCER RISK AMONG WOMEN IN HARRIS COUNTY, TEXAS, 1977-1980 (OCCUPATION, SMOKING, BYSTANDER)

Excessively high, accelerating lung cancer rates among women in Harris County, Texas, prompted this case-comparison study. Objectives were to compare patterns of employment, indirect exposures, and sociodemographic variables of lung cancer cases with comparison subjects (compeers) after standardizing for possible confounders, such as age and cigarette smoking. Lung cancer cases were microscopically confirmed, white, Harris County residents. Compeers, chosen from Medicare records and Texas Department of Public Safety records, were matched on gender, race, age, resident and vital status. Personal interviews were conducted with study subjects or next-of-kin. Industries and occupations were categorized as high risk, based on previous studies.^ Almost all cases (95.0%) and 60.0% of compeers smoked cigarettes. The odds ratio for lung cancer and smoking is 13.9. Stopping smoking between ages 30-50 years carries a lower risk than stopping at age 58 or more years. Women's employment in a high risk industry or occupation results in consistently elevated, smoking-adjusted odds ratios. Frequency and duration of employment demonstrate a moderate dose-response effect. A temporal association exists with employment in a high risk occupation during 1940-1949.^ No increased risk appeared with passive smoking. Husband's employment in a construction industry or a structural occupation significantly increased the smoking-adjusted odds ratios among cases and compeers (O.R. = 2.9, 2.2). Smoking-adjusted odds ratios increased significantly when women had resided with persons employed in cement (O.R. = 3.2) or insulation (O.R. = 5.5) manufacturing, or a high rise construction industry (O.R. = 2.4). A family history of lung cancer resulted in a two-fold increase in smoking-adjusted odds ratios. Vital status of compeers affected the odds ratios.^ Work-related exposures appear to increase the risk of lung cancer in women although cigarette smoking has the single highest odds ratio. Indirect exposure to certain employment also plays a significant role in lung cancer in women. Investigations of specific direct and indirect hazardous exposures in the workplace and home are needed. Cigarette smoking is as hazardous for women as for men. Smoking should be prevented and eliminated. ^

Facing the climate change challenges in the mining and mineral industry as providers of a sustainable manufacturing process

A sustainable manufacturing process must rely on an also sustainable raw materials and energy supply. This paper is intended to show the results of the studies developed on sustainable business models for the minerals industry as a fundamental previous part of a sustainable manufacturing process. As it has happened in other economic activities, the mining and minerals industry has come under tremendous pressure to improve its social, developmental, and environmental performance. Mining, refining, and the use and disposal of minerals have in some instances led to significant local environmental and social damage. Nowadays, like in other parts of the corporate world, companies are more routinely expected to perform to ever higher standards of behavior, going well beyond achieving the best rate of return for shareholders. They are also increasingly being asked to be more transparent and subject to third-party audit or review, especially in environmental aspects. In terms of environment, there are three inter-related areas where innovation and new business models can make the biggest difference: carbon, water and biodiversity. The focus in these three areas is for two reasons. First, the industrial and energetic minerals industry has significant footprints in each of these areas. Second, these three areas are where the potential environmental impacts go beyond local stakeholders and communities, and can even have global impacts, like in the case of carbon. So prioritizing efforts in these areas will ultimately be a strategic differentiator as the industry businesses continues to grow. Over the next forty years, world?s population is predicted to rise from 6.300 million to 9.500 million people. This will mean a huge demand of natural resources. Indeed, consumption rates are such that current demand for raw materials will probably soon exceed the planet?s capacity. As awareness of the actual situation grows, the public is demanding goods and services that are even more environmentally sustainable. This means that massive efforts are required to reduce the amount of materials we use, including freshwater, minerals and oil, biodiversity, and marine resources. It?s clear that business as usual is no longer possible. Today, companies face not only the economic fallout of the financial crisis; they face the substantial challenge of transitioning to a low-carbon economy that is constrained by dwindling natural resources easily accessible. Innovative business models offer pioneering companies an early start toward the future. They can signal to consumers how to make sustainable choices and provide reward for both the consumer and the shareholder. Climate change and carbon remain major risk discontinuities that we need to better understand and deal with. In the absence of a global carbon solution, the principal objective of any individual country should be to reduce its global carbon emissions by encouraging conservation. The mineral industry internal response is to continue to focus on reducing the energy intensity of our existing operations through energy efficiency and the progressive introduction of new technology. Planning of the new projects must ensure that their energy footprint is minimal from the start. These actions will increase the long term resilience of the business to uncertain energy and carbon markets. This focus, combined with a strong demand for skills in this strategic area for the future requires an appropriate change in initial and continuing training of engineers and technicians and their awareness of the issue of eco-design. It will also need the development of measurement tools for consistent comparisons between companies and the assessments integration of the carbon footprint of mining equipments and services in a comprehensive impact study on the sustainable development of the Economy.

Sistema de gestión de residuos de construcción y demolición en obras de edificación residencial. Buenas prácticas en la ejecución de obra

En el sector de la edificación, las grandes constructoras comienzan a considerar aspectos medioambientales, no limitándose a lo establecido por la legislación vigente, y buscando la implementación de buenas prácticas. Si bien este hecho es una realidad para las grandes empresas constructoras, todavía falta que la gran mayoría de las empresas del sector (pequeñas y medianas) adopten ésta tendencia. En este sentido, las publicaciones y estadísticas consultadas revelan que el sector de la construcción sigue siendo el sector con menor número de Sistemas de Gestión Ambiental (SGA) certificados en comparación con otros sectores industriales, debido principalmente a las peculiaridades de su actividad. Por otra parte, el sector de la construcción genera grandes cantidades de residuos de construcción y demolición (RCD). Aunque, en los últimos años la actividad de la construcción ha disminuido, debido a la crisis económica del país, no hay que olvidar todos los problemas causados por este tipo de residuos, o mejor dicho, por su gestión. La gestión de los RCD actual está lejos de alcanzar la meta propuesta en la Directiva Marco de Residuos (DMR), la cual exige un objetivo global para el año 2020 en el que el 70% de todos los RCD generados deberán ser reciclados en los países de la UE. Pero, la realidad es que sólo el 50% de la RCD generados en la Unión Europea se recicla. Por este motivo, en los últimos años se ha producido una completa modificación del régimen jurídico aplicable a los RCD, incorporando importantes novedades a nuestro ordenamiento interno como son: la redacción de un Estudio de gestión de RCD (en fase de diseño) y un Plan de gestión de RCD (en fase de ejecución). Entre estas medidas destaca el poder conocer, con la antelación suficiente, la cantidad y el momento en que los RCD son generados, para así poder planificar la gestión más adecuada para cada categoría de RCD. Es por ello que el desarrollo de cualquier instrumento que determine la estimación de RCD así como iniciativas para su control debe ser considerado como una herramienta para dar respuestas reales en el campo de la sostenibilidad en la edificación. Por todo lo anterior, el principal objetivo de la Tesis Doctoral es mejorar la gestión actual de los RCD, a través de la elaboración e implementación en obra de un Sistema de gestión de RCD en fase de ejecución que podrá ser incluido en el Sistema de Gestión Ambiental de las empresas constructoras. Para ello, se ha identificado la actividad que más residuo genera, así como las diferentes categorías de RCD generadas durante su ejecución, a través del análisis de nueve obras de edificación de nueva planta. Posteriormente, se han determinado y evaluado, en función de su eficacia y viabilidad, veinte buenas prácticas encaminadas a reducir la generación de RCD. También, se han identificado y evaluado, en función de su coste económico, cinco alternativas de gestión para cada categoría de RCD generada. Por último, se ha desarrollado e implementado un Sistema de Gestión de RCD en una empresa de construcción real. En definitiva, el Sistema de Gestión de RCD propuesto contiene una herramienta de estimación de RCD y también proporciona una relación de buenas prácticas, según su viabilidad y eficacia, sobre los aspectos más significativos en cuanto a la gestión de RCD se refiere. El uso de este Sistema de gestión de RCD ayudará a los técnicos de la construcción en el desarrollo de los documentos "Estudio de gestión de RCD " y "Plan de gestión de RCD " - requeridos por ley -. Además, el Sistema promueve la gestión ambiental de la empresa, favoreciendo la cohesión del proceso constructivo, estableciendo responsabilidades en el ámbito de RCD y proporcionando un mayor control sobre el proceso. En conclusión, la implementación de un sistema de gestión de RCD en obra ayuda a conseguir una actividad de edificación, cuyo principal objetivo sea la generación de residuos cero. ABSTRACT Currently, in the building sector, the main construction companies are considering environmental issues, not being limited to the current legislation, and seeking the implementation of good practices. While this fact is a reality for large construction companies, still the vast majority of construction companies (small and medium enterprises) need to accept this trend. In this sense, official publications and statistics reveal that the construction sector remains with the lowest number of certified Environmental Management Systems (EMS) compared to other industrial sectors, mainly due to the peculiarities of its activity. Moreover, the construction industry in Spain generates large volumes of construction and demolition waste (CDW) achieving a low recycling rate compared to other European Union countries and to the target set for 2020. Despite the complete change in the legal regime for CDW in Spain, there are still several difficulties for their application at the construction works. Among these difficulties the following can be highlighted: onsite segregation, estimating CDW generation and managing different CDW categories. Despite these difficulties, the proper CDW management must be one of the main aspects considered by construction companies in the EMS. However, at present the EMS used in construction companies consider very superficially CDW management issues. Therefore, current EMS should go a step further and include not only procedures for managing CDW globally, but also specific procedures for each CDW category, taking into account best practices for prevention, minimization and proper CDW management in order to achieve building construction works with zero waste generation. The few scientific studies analysing EMS implementation in construction enterprises focus on studying the benefits and barriers of their implementation. Despite the drawbacks found, implementing an EMS would bring benefits such as improving the corporate image in relation to the environment, ensuring compliance with the law or reducing environmental risks. Also, the international scientific community has shown great interest in defining models to estimate in advance the CDW that will be generated during the building construction or rehabilitation works. These studies analyse the overall waste generation and its different CDW categories. However, despite the many studies found on CDW quantification, analysing its evolution throughout the construction activities is a factor that must be further studied and discussed in greater depth, as results would be of great significance when planning the CDW management. According to the scientific studies analysing the implementation of good environmental practices in construction sites, it seems that, in general, the CDW collection system is done in a decentralized manner by each subcontracted company. In addition, the corporate image generated when poor practices are done may adversely affect the company's reputation and can result in loss of contracts. Finally, although there are numerous guides and manuals of good practices for CDW management, no references have been found implementing these measures in the Environmental Management System of the construction companies. From all the above, this thesis aims to provide answers to reduce the environmental impact caused by CDW generation in building construction works, in order to get a building process with zero waste generation. In this sense, is essential to generate new knowledge in order to implement a system which can carry out comprehensive management of CDW generated onsite, at the design stage until the end of its life cycle, taking into account both technical and economic criteria. Therefore, the main objective of this thesis is to define and implement a CDW management system for residential building construction works, helping construction agents not only to manage the CDW in accordance with current legislation, but also minimizing their generation on site by applying best practices, resulting in achieving the goal of zero waste in building works.

Factors impacting the market share of Construction and Demolition (C&D) Waste recycling solutions

Current EU Directives force the Member States to assure by 2020 that 70% of the Construction and Demolition (C&D) waste is recovered instead of landfilled. While some countries have largely achieved this target, others still have a long way to go. For better understanding the differences arising from local disparities, six factors related to technical, economic, legislative and environmental aspects have been identified as crucial influences in the market share of C&D waste recycling solutions. These factors are able to identify the causes that limit the recycling rate of a certain region. Moreover, progress towards an efficient waste management can vary through the improvement of a single factor. This study provides the background for further fine-tuning the factors and their combination into a mathematical model for assessing the market share of C&D recycling solutions.

The Practicality of Sustainable Development in Construction

The implementation of sustainable construction practices aims to reduce the environmental impact of development without hindering the economic or social growth of society and industry. An analysis of sustainable construction was conducted to understand the viability, environmental and economic impacts of sustainable building practices. The research indicates sustainable construction offers substantial economic and environmental advantages. However, the construction industry has yet to universally adopt sustainable practices. The solutions I have determined to help foster the adoption of sustainable construction include enhanced planning and design, implementing waste management, educating industry professionals and increasing public awareness about the benefits. The research and recommendations in this project prove the hypothesis and offer solutions that, when implemented will benefit society.

Remaking Movie Making: The Environmental Impacts of the Film Industry in Southern California

The film and television industry is integral to the economics and culture of the Southern California region. It is also a major contributing factor to the environmental problems in the region. Currently the Motion Picture, Television, and Commercial Industries Act of 1984 is the only regulation written specifically for the entertainment industry. This regulation was created with the purpose of streamlining the film permitting process to prevent run-away production, taking production out of state, and encourage growth. A change in this regulation is needed since studios routinely fail to meet environmental standards or work towards improvement during on-location filming. Amendments to this regulation requiring permits to contain environmental conditions would improve environmental conditions and stay true to the original purpose of the act.

Coping with extreme weather:strategies of construction SMEs

Weather extremes have created a considerable impact on Small and Medium-sized Enterprises (SMEs) in the UK during the recent years, especially on SMEs in the construction sector. Evidence in relation to the recent weather extremes have demonstrated that SMEs are some of the worst impacted by the Extreme Weather Events (EWEs) and have confirmed them as a highly vulnerable section of the UK economy to the impact of extreme weather. This is of particular importance to the construction industry, as an overarching majority of construction companies are SMEs who account for the majority of employment and income generation within the industry. Whilst construction has been perceived as a sector significantly vulnerable to the impacts of EWEs, there is scant evidence of how construction SMEs respond to such events and cope with their impact. Based on the evidence emerged from case studies of construction SMEs, current coping strategies of construction SMEs were identified. Some of the strategies identified were focused at organisational level whereas others were focused at project level. Further, some of the strategies were general risk management / business continuity strategies whereas others have been specifically developed to address the risk of EWEs. Accordingly, coping strategies can be broadly categorised based on their focus; i.e. those focused at project or organisational level, and based on the risks that they seek to address; i.e. business / continuity risks in general or EWE risk specifically. By overlapping these two aspects; their focus and risks that they seek to address, four categories of coping strategies can be devised. There are; general risk management strategies focused at business level, general risk management strategies focused at project level, EWE specific strategies focused at business level, and EWE specific strategies focused at project level. It is proposed that for a construction SME to effectively cope with the impact of EWEs and develop their resilience against EWEs a rich mix of these coping strategies are required to suite the particular requirements of the business.

Sustainable solutions for the construction sector: integration of secondary raw materials in the production cycle of concrete

The construction industry is one of the largest consumers of raw materials and energy and one of the highest contributor to green-houses gases emissions. In order to become more sustainable it needs to reduce the use of both raw materials and energy, thus lim-iting its environmental impact. Developing novel technologies to integrate secondary raw materials (i.e. lightweight recycled aggre-gates and alkali activated “cementless” binders - geopolymers) in the production cycle of concrete is an all-inclusive solution to im-prove both sustainability and cost-efficiency of construction industry. SUS-CON “SUStainable, Innovative and Energy-Efficiency CONcrete, based on the integration of all-waste materials” is an European project (duration 2012-2015), which aim was the inte-gration of secondary raw materials in the production cycle of concrete, thus resulting in innovative, sustainable and cost-effective building solutions. This paper presents the main outcomes related to the successful scaling-up of SUS-CON concrete solutions in traditional production plants. Two European industrial concrete producers have been involved, to design and produce both pre-cast components (blocks and panels) and ready-mixed concrete. Recycled polyurethane foams and mixed plastics were used as aggre-gates, PFA (Pulverized Fuel Ash, a by-product of coal fuelled power plants) and GGBS (Ground Granulated Blast furnace Slag, a by-product of iron and steel industries) as binders. Eventually, the installation of SUS-CON concrete solutions on real buildings has been demonstrated, with the construction of three mock-ups located in Europe (Spain, Turkey and Romania)

Alkali-Activated Natural Pozzolan Concrete as New Construction Material

In the near future, geopolymers or alkali-activated cementitious materials will be used as new high-performance construction materials of low environmental impact with a reasonable cost. This material is a good candidate to partially replace ordinary portland cement (OPC) in concrete as a major construction material that plays an outstanding role in the construction industry of different structures. Geopolymer materials are inorganic polymers based on alumina and silica units; they are synthesized from a wide range of dehydroxylated alumina-silicate powders condensed with alkaline silicate in a highly alkaline environment. Geopolymeric materials can be produced from a wide range of alumina-silica, including natural products--such as natural pozzolan and metakaolin--or coproducts--such as fly ash (coal and lignite), oil fuel ash, blast furnace or steel slag, and silica fume--and provide a route toward sustainable development. Using lesser amounts of calcium-based raw materials, lower manufacturing temperature, and lower amounts of fuel result in reduced carbon emissions for geopolymer cement manufacture up to 22 to 72% in comparison with portland cement. A study has been done by the authors to investigate the intrinsic nature of different types of Iranian natural pozzolans to determine the activators and methods that could be used to produce a geopolymer concrete based on alkali-activated natural pozzolan (AANP) and optimize mixture design. The mechanical behavior and durability of these types of geopolymer concrete were investigated and compared with normal OPC concrete mixtures cast by the authors and also reported in the literature. This paper summarizes the main conclusions of the research regarding pozzolanic activity, activator properties, engineering and durability properties, applications and evaluation of carbon footprint, and cost for AANP concrete.

Medidas de concentração de radônio proveniente de argamassas de cimento portland, gesso e fosfogesso

Portland cement being very common construction material has in its composition the natural gypsum. To decrease the costs of manufacturing, the cement industry is substituting the gypsum in its composition by small quantities of phosphogypsum, which is the residue generated by the production of fertilizers and consists essentially of calcium dihydrate and some impurities, such as fluoride, metals in general, and radionuclides. Currently, tons of phosphogypsum are stored in the open air near the fertilizer industries, causing contamination of the environment. The 226 Ra present in these materials, when undergoes radioactive decay, produces the 222Rn gas. This radioactive gas, when inhaled together with its decay products deposited in the lungs, produces the exposure to radiation and can be a potential cause of lung cancer. Thus, the objective of this study was to measure the concentration levels of 222Rn from cylindrical samples of Portland cement, gypsum and phosphogypsum mortar from the state of Paraná, as well as characterizer the material and estimate the radon concentration in an environment of hypothetical dwelling with walls covered by such materials. Experimental setup of 222Rn activity measurements was based on AlphaGUARD detector (Saphymo GmbH). The qualitative and quantitative analysis was performed by gamma spectrometry and EDXRF with Au and Ag targets tubes (AMPTEK), and Mo target (ARTAX) and mechanical testing with x- ray equipment (Gilardoni) and the mechanical press (EMIC). Obtained average values of radon activity from studied materials in the air of containers were of 854 ± 23 Bq/m3, 60,0 ± 7,2 Bq/m3 e 52,9 ± 5,4 Bq/m3 for Portland cement, gypsum and phosphogypsum mortar, respectively. These results extrapolated into the volume of hypothetical dwelling of 36 m3 with the walls covered by such materials were of 3366 ± 91 Bq/m3, 237 ± 28 Bq/m3 e 208 ± 21 Bq/m3for Portland cement, gypsum and phosphogypsum mortar, respectively. Considering the limit of 300 Bq/m3 established by the ICRP, it could be concluded that the use of Portland cement plaster in dwellings is not secure and requires some specific mitigation procedure. Using the results of gamma spectrometry there were calculated the values of radium equivalent activity concentrations (Raeq) for Portland cement, gypsum and phosphogypsum mortar, which were obtained equal to 78,2 ± 0,9 Bq/kg; 58,2 ± 0,9 Bq/kg e 68,2 ± 0,9 Bq/kg, respectively. All values of radium equivalent activity concentrations for studied samples are below the maximum level of 370 Bq/kg. The qualitative and quantitative analysis of EDXRF spectra obtained with studied mortar samples allowed to evaluate quantitate and the elements that constitute the material such as Ca, S, Fe, and others.

Avaliação de tipologias construtivas nos critérios de sustentabilidade : estudo de casos – telhas

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Arquitetura e Urbanismo, Programa de Pós-Graduação em Arquitetura e Urbanismo, 2016.

Labour productivity in Iranian construction projects perceptions of chief executive officers

Purpose – The purpose of this paper is twofold. First, it aims to highlight the main factors and items affecting the productivity of construction projects, based on the perceptions of CEOs in construction companies in Iran. Second, the study compares the elicited CEOs’ perceptions against the findings of studies based on the views of such as project managers, middle managers and employees in other levels. Design/methodology/approach – The study drew upon literature on construction work to develop a conceptual model. Further, a total of 60 CEOs from road construction companies were surveyed using a five-point Likert scale questionnaire to generate the data. The collated data were categorised and ranked according to the CEOs perceived level of importance using the relative importance index. Findings – The findings highlight the main factors and items affecting labour productivity in construction projects in Iran as perceived by CEOs, which are mainly of human resources management nature and could be attributed to motivation and managerial policy aspects. The study also recognises that factors associated with the working environment particularly safety and health are perceived as insignificant by Iranian CEOs which could be a concern for the Iranian construction industry. The discussions shed some light on the discrepancies between the perceptions of CEOs and previous studies in regards to major determinants of productivity in the construction context. Originality/value – This study is the first study aiming at discussing the perceptions of CEOs of construction companies active in construction projects in Iran. As such, the study highlights the standpoint of the main decision makers in construction companies in regards to labour productivity in the construction sector. Thus, the key contribution of the present study is providing insight into the perceptions of CEOs, who play the most vital role in strategic development of construction companies whereas previous studies have mostly focused on project or middle managers having a lower influence in determining the strategic plans of companies.

Improving waste management in construction projects: an Australian study

Construction waste generation has been identified as one of the major issues in the construction industry due to its direct impacts on the environment as well as the efficiency of the construction industry. As the industry cannot continue to practice if the environmental resources on which it depends are depleted, the significance of waste management needs to be understood in order to encourage stakeholders to achieve related goals. Therefore, this research aims to determine effective approaches to eliminate and/or minimise waste generation in construction projects. Mixed methods were adopted by combining qualitative and quantitative research approaches. Interviews and a questionnaire survey were conducted as the primary data collection methods. The findings reveal twenty six critical solutions for waste management. Five factors of solutions for waste management were extracted from the exploratory factor analysis. These factors were: team building and supervision; strategic guidelines in waste management; proper design and documentation; innovation in waste management decisions; and lifecycle management. The evidence from this study suggests that both technologies and attitudinal approaches require improvement to eliminate/minimise waste generation in construction projects. Similarly, attention should be paid to being mindful of the environmental effects of waste generation and avoiding waste generation as early as possible in construction projects.