COMPRESSION BEHAVIOR AT HIGH STRAIN RATE FOR AN ULTRA HIGH PERFORMANCE CONCRETE

The need for a stronger and more durable building material is becoming more important as the structural engineering field expands and challenges the behavioral limits of current materials. One of the demands for stronger material is rooted in the effects that dynamic loading has on a structure. High strain rates on the order of 101 s-1 to 103 s-1, though a small part of the overall types of loading that occur anywhere between 10-8 s-1 to 104 s-1 and at any point in a structures life, have very important effects when considering dynamic loading on a structure. High strain rates such as these can cause the material and structure to behave differently than at slower strain rates, which necessitates the need for the testing of materials under such loading to understand its behavior. Ultra high performance concrete (UHPC), a relatively new material in the U.S. construction industry, exhibits many enhanced strength and durability properties compared to the standard normal strength concrete. However, the use of this material for high strain rate applications requires an understanding of UHPC’s dynamic properties under corresponding loads. One such dynamic property is the increase in compressive strength under high strain rate load conditions, quantified as the dynamic increase factor (DIF). This factor allows a designer to relate the dynamic compressive strength back to the static compressive strength, which generally is a well-established property. Previous research establishes the relationships for the concept of DIF in design. The generally accepted methodology for obtaining high strain rates to study the enhanced behavior of compressive material strength is the split Hopkinson pressure bar (SHPB). In this research, 83 Cor-Tuf UHPC specimens were tested in dynamic compression using a SHPB at Michigan Technological University. The specimens were separated into two categories: ambient cured and thermally treated, with aspect ratios of 0.5:1, 1:1, and 2:1 within each category. There was statistically no significant difference in mean DIF for the aspect ratios and cure regimes that were considered in this study. DIF’s ranged from 1.85 to 2.09. Failure modes were observed to be mostly Type 2, Type 4, or combinations thereof for all specimen aspect ratios when classified according to ASTM C39 fracture pattern guidelines. The Comite Euro-International du Beton (CEB) model for DIF versus strain rate does not accurately predict the DIF for UHPC data gathered in this study. Additionally, a measurement system analysis was conducted to observe variance within the measurement system and a general linear model analysis was performed to examine the interaction and main effects that aspect ratio, cannon pressure, and cure method have on the maximum dynamic stress.

Collective Voluntary Agreements and the Production of Less Polluting Products

Recently, some industries have collectively agreed not to produce models that do not meet an energy efficiency (and hence an environmental) standard. This paper presents a simple model that can be used to examine a voluntary collective agreement to limit or completely eliminate the low efficiency model of a given product (e.g., a low efficiency washing machine). We show that, when there is competition between firms, a collective agreement to limit or even eliminate production of the polluting model can actually increase profits for all firms in the industry. This suggests that a collective agreement of this type might actually be beneficial to firms, while at the same time improving environmental quality. However, the implicit enforcement that comes from the public nature of the commitment is necessary to ensure this outcome. This suggests that, by promoting such agreements, policymakers may be able to achieve substantial environmental gains with relatively little inducement. The impact on social welfare will then depend on whether these gains are sufficiently large to offset consumer losses from reductions in product variety and the associated price increases.

How did the crisis affect small and medium-sized enterprises? -- from a field study of the metal-working industry in Java

This paper focuses on the impact of Indonesia's economic crisis on small and medium-sized enterprises (SMEs). It shows how the performance of SMEs during the crisis varied widely even in the same industrial subsector, and found that the factors most affecting performance have been market orientation and the linkages that the SMEs have formed with the buyers of their products. Well-performing SMEs were found to have utilized putting-out linkages with wholesalers which enabled them to switch to products having better markets. On the other hand, the SMEs which had subcontracting linkages with assemblers or contracting linkages with user-factories (with the exception of SMEs having export-oriented linkages) suffered badly in the crisis because of specificity of products with little room for switching. The paper also found that exposure to debt due to borrowing for investment has been another factor affecting performance, but that enterprise size has had no linear correlation with performance.

Export-Led Growth and Geographic Distribution of the Poultry Meat Industry in Brazil

This paper includes an examination of the sustainability of recent high growth in the poultry meat industry in Brazil. In addition, an assessment is made of the impact of increased production of poultry meat products on the development of local industries. Comparative studies of leading companies in the United States, Mexico, and Brazil reveal competitive advantages in the low costs of feedstuff and labor as well as disadvantages in the scale of business and management efficiency in the Brazilian poultry sector. Increases in domestic and foreign demand for Brazilian poultry meat have promoted development of the Brazilian poultry sector in local areas. The formation of industrial clusters is observed using regional data related to the location of slaughterhouses and the number of chickens farmed. Statistical analyses support observations made in this paper.

The Impact of United States Sanctions on the Myanmar Garment Industry

The United States imposed trade sanctions against the military regime in Myanmar in July 2003. The import ban damaged the garment industry in particular. This industry exported nearly half of its products to the United States, and more than eighty percent of United States imports from Myanmar had been clothes. The garment industry was probably the main target of the sanctions. Nevertheless, the impact on the garment industry and its workers has not been accurately evaluated or closely examined. The purpose of this paper is to evaluate the impact of the sanctions and to further understand the present situation. This is done using several sources of information, including the author's field and questionnaire surveys. This paper also describes the process of selection and polarization underway in the garment industry, an industry that now has more severe competition fueled by the sanctions. Through such a process, the impact was inflicted disproportionately on small and medium-sized domestic firms and their workers.

Value Chain Dynamics and Growth of Local Firms:The Case of Motorcycle Industry in Vietnam

Vietnam’s burgeoning market for motorcycles has attracted global industry eaders,players from developing countries, and local firms. This has led to a dynamic evolution of value chains. This paper presents an explanation of the varieties of the growth patterns xperienced by the local suppliers, focusing on the roles of customer and local supplier strategies. Case studies showed that while the role of customers may be important, strategies of suppliers to improve the ompetitive edge in the production of otorcycle components and to diversify into other products account for important ariations of growth trajectories among local suppliers. Findings presented in this paper suggest the need to direct more attention to strategy that local firms use to boost their competitive edge in business.

The Iron and Steel Industry in Asia: Development and Restructuring

The paper examines the development and restructuring of the iron and steel industry in Asian countries. Studying countries that have integrated steelworks with large blast furnaces (South Korea, Taiwan, China and India) and countries without (Thailand, Indonesia and Malaysia), the paper shows the difference in the development processes across the countries and across time, and points to the diversity of the development experience of these countries. The paper argues that significant differences in steel production technologies in terms of initial investment and minimum-efficient scale, the changing role of the state, and shifting demand structures in the domestic steel markets of each country have been the important factors that led to the differences in the development path of the steel industry in each country.

Chapter 1 Economic Integration and Industry Location: Theories, Empirical Results, and Implications for CLMV

Trade affects the internal location of industry in two ways: it induces firms to specialize and it expands the set of markets that firms serve. If there are industry-specific external economies, firms in related industries will spatially agglomerate (Hanson 1996a). In the context of economic integration, diminished barriers to trade affect industry location particularly in less developed countries. As described below, regional agreements in North America and Europe have caused frontier regions to expand. These regions, which include border regions and port cities, have advantages over internal regions in terms of access to foreign markets. Since trade liberalization induces many firms in developing countries to participate in production networks and to specialize in labor-intensive activities such as assembling and processing of foreign-made components, their inputs as well as final products need to be carried across borders. Therefore, the best industry location, one that minimizes transport costs, is likely to shift to frontier regions. In East Asia, China has developed rapidly since it opened up to international trade. Simultaneously, a large amount of foreign direct investment (FDI) has been attracted and industry agglomerations have been formed in coastal regions, that is, frontier regions linked to the global market by sea, leaving many internal regions behind. Similarly, Cambodia, Laos, Myanmar, and Vietnam (CLMV) have joined AFTA and/or the WTO and liberalized international trade since the 1990s. Moreover, transport infrastructures such as the East-West Economic Corridor, the Southern Economic Corridor, and the North-South Economic Corridor have been built and narrowed economic distances in the Greater Mekong Subregion (GMS). As a result, frontier regions are likely to increase their location advantages and lure labor-intensive operations from neighboring countries. It is expected that, as has happened in North America and Europe, economic integration in East Asia will significantly affect internal geography in CLMV. In this study, I first review theories relevant to economic integration and industry location within a country. In particular, emphasis is placed on the new economic geography (NEG). Secondly, empirical results for North America and Europe are surveyed since they have preceded East Asia in regional integration and a substantial number of studies have been conducted on these regions. The final section summarizes and discusses implications for internal geography in CLMV.

Status and constraints of costly port rejection : a case from the Vietnamese frozen seafood export industry

While the rising exports have been the source of growth for many developing countries in recent years, the rate of commodities rejected at the ports of developed countries has also been high. Yet why it has remained so despite the costs involved is mostly unknown. This paper takes a case of the frozen seafood export industry in Vietnam and examines the current status of port rejection, roles played by various stakeholders along the value chains, and the constraints faced by the Vietnamese producers and exporters. It concludes with some policy implications, including strengthening the enforcement mechanism of standards compliance particularly at the upstream of the value chain and providing public testing labs for small-scale producers.

Product quality and intra-industry trade

In this study, we argue that the conventional intra-industry trade (IIT) index does not address the quality issue directly and propose a methodology to make full use of unit-price gap information to deduce quality differences between simultaneously exported and imported products. By applying this measure to German trade data at the eight-digit level, we study the quality improvement of Chinese export goods in its IIT with Germany. We compare the case of China with those of Eastern European countries, which are also major trading partners of Germany. Our results show that the unit-value difference in IIT between Germany and Eastern European countries is clearly narrowing. However, China's export prices to Germany are much lower than Germany's export prices to China, and this gap has not narrowed over the last 23 years. This is at odds with the common perception that China's product quality has improved, as documented by Rodrik (2006) and Schott (2008). Our results support Xu (2010), which argued that incorporating the quality aspect of the exported goods weakens or even eliminates the evidence of the sophistication of Chinese export goods in Rodrik (2006).

On the stability of intra-industry trade

This paper presents the novel finding that two-way intra-industry trade (IIT) in product–country pairs is very unstable over time by using disaggregated trade data of OECD countries. Many products frequently switch among two-way, one-way and zero trade over time. To measure the stability of two-way trade, we propose a measure that we refer to as the "IIT stability index". Our estimation results using the proposed measure show that two-way trade involving markets of different sizes and long distance are likely to be unstable. In addition, primary products are more unstable than manufactured products.

The use of computers for graduate education in Project Management. Improving the integration to the industry.

This paper presents an initiative for monitoring the competence acquisition by a team of students with different backgrounds facing the experience of being working by projects and in a project. These students are graduated bachelor engineering are inexperienced in the project management field and they play this course on a time-shared manner along with other activities. The goal of this experience is to increase the competence levels acquired by using an structured web based portfolio tool helping to reinforce how relevant different project management approaches can result for final products and how important it becomes to maintain the integration along the project. Monitoring is carried out by means of have a look on how the work is being done and measuring different technical parameters per participant. The use of this information could make possible to bring additional information to the students involved in terms of their individual competencies and the identification of new opportunities of personal improvement. These capabilities are strongly requested by companies in their daily work as well as they can be very convenient too for students when they try to organize their PhD work.

Approach to the use of indicators for the assessment of the environmental level of construction products

The European construction industry is supposed to consume the 40% of the natural European resources and to generate the 40% of the European solid waste. Conscious of the great damage being suffered by the environment because of construction activity, this work tries to provide the building actors with a new tool to improve the current situation. The tool proposed is a model for the comprehensive evaluation of construction products by determining their environmental level. In this research, the environmental level of a construction product has been defined as its quality of accomplishing the construction requirements needed by causing the minimum ecological impact in its surrounding environment. This information allows building actors to choose suitable materials for building needs and also for the environment, mainly in the project stage or on the building site, contributing to improve the relationship between buildings and environment. For the assessment of the environmental level of construction products, five indicators have been identified regarding their global environmental impact through the product life cycle: CO2 emissions provoked during their production, volume and toxicity of waste generated on the building site, durability and recycling capacity after their useful life. Therefore, the less environmental impact one construction product produces, the higher environmental level performs. The model has been tested in 30 construction products that include environmental criteria in their description. The results obtained will be discussed in this article. Furthermore, this model can lay down guidelines for the selection of ecoefficient construction products and the design of new eco-competitive and eco-committed ones

Influence of cement properties in the reaction rate and mechanical behavior of concrete with high fl y ash content

The use of fly ash (FA) as an admixture to concrete is broadly extended for two main reasons: the reduction of costs that supposes the substitution of cement and the micro structural changes motivated by the mineral admixture. Regarding this second point, there is a consensus that considers that the ash generates a more compact concrete and a reduction in the size of the pore. However, the measure in which this contributes to the pozzolanic activity or as filler is not well defined. There is also no justification to the influence of the physical parameters, fineness of the grain and free water, in its behavior. This work studies the use of FA as a partial substitute of the cement in concretes of different workability (dry and wet) and the influence in the reactivity of the ash. The concrete of dry consistency which serves as reference uses a cement dose of 250 Kg/m 3 and the concrete of fluid consistency utilized a dose of cement of 350 Kg/m 3 . Two trademark of Portland Cement Type 1 were used. The first reached the resistant class for its fineness of grain and the second one for its composition. Moreover, three doses of FA have been used, and the water/binder ratio was constant in all the mixtures. We have studied the mechanical properties and the micro-structure of the concretes by means of compressive strength tests, mercury intrusion porosimetry (MIP) and thermal analysis (TA). The results of compressive strength tests allow us to observe that concrete mixtures with cements of the same classification and similar dosage of binder do not present the same mechanical behavior. These results show that the effective water/binder ratio has a major role in the development of the mechanical properties of concrete. The study of different dosages using TA, thermo-gravimetry and differential thermal analysis, revealed that the portlandite content is not restrictive in any of the dosages studied. Again, this proves that the rheology of the material influences the reaction rate and content of hydrated cement products. We conclude that the available free water is determinant in the efficiency of pozzolanic reaction. It is so that in accordance to the availability of free water, the ashes can react as an active admixture or simply change the porous distribution. The MIP shows concretes that do not exhibit significant changes in their mechanical behavior, but have suffered significant variation in their porous structure

Desintegración vertical en la industria del automóvil en España: un caso de estudio = Vertical disintegration in the automotive industry in Spain: a case study

En los años recientes se ha producido un rápido crecimiento del comercio internacional en productos semielaborados que son diseñados, producidos y ensamblados en diferentes localizaciones a lo largo de diferentes países, debido principalmente a los siguientes motivos: el desarrollo de las tecnologías de la información, la reducción de los costes de transporte, la liberalización de los mercados de capitales, la armonización de factores institucionales, la integración económica regional que implica la reducción y la eliminación de las barreras al comercio, el desarrollo económico de los países emergentes, el uso de economías de escala, así como una desregulación del comercio internacional. Todo ello ha incrementado la competencia a nivel mundial en los mercados y ha posibilitado a las compañías tener más facilidad de acceso a potenciales mercados, así como a la adquisición de capacidades y conocimientos en otros países y a la realización de alianzas estratégicas internacionales con terceros, creando un entorno con mayor incertidumbre y más exigente para las compañías que componen una industria, y que tiene consecuencias directas en las operaciones de las compañías y en la organización de su producción. Las compañías, para adaptarse, ser competitivas y beneficiarse de este nuevo escenario globalizado y más competitivo, han externalizado partes del proceso productivo hacia proveedores especializados, creando un nuevo mercado intermedio que divide el proceso productivo, anteriormente integrado en las compañías que conforman una industria, entre dos conjuntos de empresas especializadas en esa industria. Dicho proceso suele ocurrir conservando la industria en que tiene lugar, los mismos servicios y productos, la tecnología empleada y las compañías originales que la conformaban previamente a la desintegración vertical. Todo ello es así debido a que es beneficioso tanto para las compañías originales de la industria como para las nuevas compañías de este mercado intermedio por diversos motivos. La desintegración vertical en una industria tiene unas consecuencias que la transforman completamente, así como la forma de operar de las compañías que la integran, incluso para aquellas que permanecen verticalmente integradas. Una de las características más importantes de esta desintegración vertical en una industria es la posibilidad que tiene una compañía de adquirir a una tercera la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por la compañía adquiriente con la práctica del outsourcing; así mismo, una compañía puede realizar la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por una tercera compañía con la práctica de la fragmentación. El principal objetivo de la presente investigación es el estudio de los motivos, los facilitadores, los efectos, las consecuencias y los principales factores significativos, microeconómicos y macroeconómicos, que desencadenan o incrementan la práctica de la desintegración vertical en una industria; para ello, la investigación se divide en dos líneas completamente diferenciadas: el estudio de la práctica del outsourcing y, por otro lado, el estudio de la fragmentación por parte de las compañías que componen la industria del automóvil en España, puesto que se trata de una de las industrias más desintegradas verticalmente y fragmentadas, y este sector posee una gran importancia en la economía del país. En primer lugar, se hace una revisión de la literatura existente relativa a los siguientes aspectos: desintegración vertical, outsourcing, fragmentación, teoría del comercio internacional, historia de la industria del automóvil en España y el uso de las aglomeraciones geográficas y las tecnologías de la información en el sector del automóvil. La metodología empleada en cada uno de ellos ha sido diferente en función de la disponibilidad de los datos y del enfoque de investigación: los factores microeconómicos, utilizando el outsourcing, y los factores macroeconómicos, empleando la fragmentación. En el estudio del outsourcing, se usa un índice basado en las compras externas sobre el valor total de la producción. Así mismo, se estudia su correlación y significación con las variables económicas más importantes que definen a una compañía del sector del automóvil, utilizando la técnica estadística de regresión lineal. Aquellas variables relacionadas con la competencia en el mercado, la externalización de las actividades de menor valor añadido y el incremento de la modularización de las actividades de la cadena de valor, han resultado significativas con la práctica del outsourcing. En el estudio de la fragmentación se seleccionan un conjunto de factores macroeconómicos, comúnmente usados en este tipo de investigaciones, relacionados con las principales magnitudes económicas de un país, y un conjunto de factores macroeconómicos, no comúnmente usados en este tipo de investigaciones, relacionados con la libertad económica y el comercio internacional de un país. Se emplea un modelo de regresión logística para identificar qué factores son significativos en la práctica de la fragmentación. De entre todos los factores usados en el modelo, los relacionados con las economías de escala y los costes de servicio han resultado significativos. Los resultados obtenidos de los test estadísticos realizados en el modelo de regresión logística han resultado satisfactorios; por ello, el modelo propuesto de regresión logística puede ser considerado sólido, fiable y versátil; además, acorde con la realidad. De los resultados obtenidos en el estudio del outsourcing y de la fragmentación, combinados conjuntamente con el estado del arte, se concluye que el principal factor que desencadena la desintegración vertical en la industria del automóvil es la competencia en el mercado de vehículos. Cuanto mayor es la demanda de vehículos, más se reducen los beneficios y la rentabilidad para sus fabricantes. Estos, para ser competitivos, diferencian sus productos de la competencia centrándose en las actividades que mayor valor añadido aportan al producto final, externalizando las actividades de menor valor añadido a proveedores especializados, e incrementando la modularidad de las actividades de la cadena de valor. Las compañías de la industria del automóvil se especializan en alguna o varias de estas actividades modularizadas que, combinadas con el uso de factores facilitadores como las economías de escala, las tecnologías de la información, las ventajas de la globalización económica y la aglomeración geográfica de una industria, incrementan y motivan la desintegración vertical en la industria del automóvil, desencadenando la coespecialización en dos sectores claramente diferenciados: el sector de fabricantes de vehículos y el sector de proveedores especializados. Cada uno de ellos se especializa en unas actividades y en unos productos o servicios específicos de la cadena de valor, lo cual genera las siguientes consecuencias en la industria del automóvil: se reducen los costes de transacción en los productos o servicios intercambiados; se incrementan la relación de dependencia entre fabricantes de vehículos y proveedores especializados, provocando un aumento en la cooperación y la coordinación, acelerando el proceso de aprendizaje, posibilitando a ambos adquirir nuevas capacidades, conocimientos y recursos, y creando nuevas ventajas competitivas para ambos; por último, las barreras de entrada a la industria del automóvil y el número de compañías se ven alteradas cambiando su estructura. Como futura línea de investigación, los fabricantes de vehículos tenderán a centrarse en investigar, diseñar y comercializar el producto o servicio, delegando el ensamblaje en manos de nuevos especialistas en la materia, el contract manufacturer; por ello, sería conveniente investigar qué factores motivantes o facilitadores existen y qué consecuencias tendría la implantación de los contract manufacturer en la industria del automóvil. 1.1. ABSTRACT In recent years there has been a rapid growth of international trade in semi-finished products designed, produced and assembled in different locations across different countries, mainly due to the following reasons: development of information technologies, reduction of transportation costs, liberalisation of capital markets, harmonisation of institutional factors, regional economic integration, which involves the reduction and elimination of trade barriers, economic development of emerging countries, use of economies of scale and deregulation of international trade. All these factors have increased competition in markets at a global level and have allowed companies to gain easier access to potential markets and to the acquisition of skills and knowledge in other countries, as well as to the completion of international strategic alliances with third parties, thus creating a more demanding and uncertain environment for these companies constituting an industry, which has a direct impact on the companies' operations and the organization of their production. In order to adapt, be competitive and benefit from this new and more competitive global scenario, companies have outsourced some parts of their production process to specialist suppliers, generating a new intermediate market which divides the production process, previously integrated in the companies that made up the industry, into two sets of companies specialized in that industry. This process often occurs while preserving the industry where it takes place, its same services and products, the technology used and the original companies that formed it prior to vertical disintegration. This is because it is beneficial for both the industry's original companies and the companies belonging to this new intermediate market, for various reasons. Vertical disintegration has consequences which completely transform the industry where it takes place as well as the modus operandi of the companies that are part of it, even of those who remain vertically integrated. One of the most important features of vertical disintegration of an industry is the possibility for a company to acquire from a third one the first part of the production process or a semi-finished product, which will then be finished by the acquiring company through the practice of outsourcing; also, a company can perform the first part of the production process or a semi-finish product, which will then be completed by a third company through the practice of fragmentation. The main objective of this research is to study the motives, facilitators, effects, consequences and major significant microeconomic and macroeconomic factors that trigger or increase the practice of vertical disintegration in a certain industry; in order to do so, research is divided into two completely differentiated lines: on the one hand, the study of the practise of outsourcing and, on the other, the study of fragmentation by companies constituting the automotive industry in Spain, since this is one of the most vertically disintegrated and fragmented industries and this particular sector is of major significance in this country's economy. First, a review is made of the existing literature, on the following aspects: vertical disintegration, outsourcing, fragmentation, international trade theory, history of the automobile industry in Spain and the use of geographical agglomeration and information technologies in the automotive sector. The methodology used for each of these aspects has been different depending on the availability of data and the research approach: the microeconomic factors, using outsourcing, and the macroeconomic factors, using fragmentation. In the study on outsourcing, an index is used based on external purchases in relation to the total value of production. Likewise, their significance and correlation with the major economic variables that define an automotive company are studied, using the statistical technique of linear regression. Variables related to market competition, outsourcing of lowest value-added activities and increased modularisation of the activities of the value chain have turned out to be significant with the practice of outsourcing. In the study of fragmentation, a set of macroeconomic factors commonly used for this type of research, is selected, related to the main economic indicators of a country, as well as a set of macroeconomic factors, not commonly used for this type of research, which are related to economic freedom and the international trade of a certain country. A logistic regression model is used to identify which factors are significant in the practice of fragmentation. Amongst all factors used in the model, those related to economies of scale and service costs have turned out to be significant. The results obtained from the statistical tests performed on the logistic regression model have been successful; hence, the suggested logistic regression model can be considered to be solid, reliable and versatile; likewise, it is in line with reality. From the results obtained in the study of outsourcing and fragmentation, combined with the state of the art, it is concluded that the main factor that triggers vertical disintegration in the automotive industry is competition within the vehicle market. The greater the vehicle demand, the lower the earnings and profitability for manufacturers. These, in order to be competitive, differentiate their products from the competition by focusing on those activities that contribute with the highest added value to the final product, outsourcing the lower valueadded activities to specialist suppliers, and increasing the modularity of the activities of the value chain. Companies in the automotive industry specialize in one or more of these modularised activities which, combined with the use of enabling factors such as economies of scale, information technologies, the advantages of economic globalisation and the geographical agglomeration of an industry, increase and encourage vertical disintegration in the automotive industry, triggering co-specialization in two clearly distinct sectors: the sector of vehicle manufacturers and the specialist suppliers sector. Each of them specializes in certain activities and specific products or services of the value chain, generating the following consequences in the automotive industry: reduction of transaction costs of the goods or services exchanged; growth of the relationship of dependency between vehicle manufacturers and specialist suppliers, which causes an increase in cooperation and coordination, accelerates the learning process, enables both to acquire new skills, knowledge and resources, and creates new competitive advantages for both; finally, barriers to entry the automotive industry and the number of companies are altered, changing their structure. As a future line of research, vehicle manufacturers will tend to focus on researching, designing and marketing the product or service, delegating the assembly in the hands of new specialists in the field, the contract manufacturer; for this reason, it would be useful to investigate what motivating or facilitating factors exist in this respect and what consequences would the implementation of contract manufacturers have in the automotive industry.