Federal motor vehicle safety standard no. 121--air brake systems : hearings before the Subcommittee on Governmental Efficiency and the District of Columbia of the Committee on Governmental Affairs, United States Senate, Ninety-fifth Congress, first- session ....

Hearings held Dec. 6, 1977-

Transactions of the Society of Automotive Engineers.

Vols. for 1918-1926 issued in 2 parts.

Automotive trade training

Mode of access: Internet.

PM TAWS : Project Manager, Tank-automotive Weapon Systems.

Mode of access: Internet.

National automotive sampling system : crashworthiness data system, 1992-1994.

"DOT HS 808 538"--P. [4] of cover.

The Corrosion Performance of Magnesium Alloy AM-SC1 in Automotive Engine Block Applications

The magnesium alloy AM-SC1 has been developed as a creep-resistant automotive engine block material. This paper outlines its corrosion performance under laboratory test conditions, considering corrosion on both the external and internal surfaces. This study found that AM-SC1 has a corrosion performance comparable to AZ91 when subjected to an aggressive salt-spray environment or in galvanic-coupling environments. This article further demonstrates that, with the appropriate selection of a commercially available engine coolant, the internal corrosion of AM-SC1 can be maintained at a tolerable level. In addition, internal corrosion resistance can be significantly improved by the addition of fluorides to the coolant solution. It is concluded that AM-SC1 can be successfully used in an engine environment provided that some simple corrosion-prevention strategies are adopted.

Light alloy castings for automotive applications: The case of Al vs Mg

The economical and environmental effects of mass reduction through Al and Mg primary alloys substitutions for cast iron and steel in automotive components are discussed using MF. Ashby's penalty functions method The viability of Mg alloy substitutions for existing Al alloy cast components is also considered. The cost analysis shows that direct, equal-volume, Al alloy substitutions for cast iron and steel are the most feasible in terms of the CAFE liability, followed by substitutions involving flat panels of prescribed stiffness. When the creation of CO2 associated to the production of Al and Mg is considered, the potential gasoline savings over the lifespan of the car compensate for the intrinsic environmental burden of Al in all applications, while electrolytic Mg substitutions for cast iron and steel are feasible for equal volume and panels only. Magnesium produced by the Pidgeon thermal process appears to be too primary energy intensive to be competitive in structural applications. Magnesium substitutions for existing Al alloy beams and panels are generally unviable. The current higher recycling efficiency of Al casting alloys confers Al a significant advantage over Mg alloys.

Automotive Central Console Interface Design

O objectivo principal deste estudo é tentar identificar as possibilidades de melhoria das interfaces físicas das consolas centrais dos automóveis, e a sua ergonomia e usabilidade enquanto meio de realização de tarefas dentro do veículo, de modo a contribuir para melhorar a experiência e a segurança na condução. Neste estudo é feita uma investigação acerca de algumas das interfaces físicas das consolas centrais, medindo o seu desempenho no que diz respeito à distracção do condutor e facilidade de uso em situações de dupla tarefa. Para isso foi adaptado um simulador de condução, e uma bateria de testes de situações de dupla tarefa foi efectuada, de modo a obter dados de telemetria de condução e de desempenho de cada interface da consola central. Os dados obtidos acerca da trajectória do veículo e da sua comparação com trajectórias de referência e a velocidade média nos sectores de condução, foram comparados com dados de desvio de olhar, e que por sua vez sã o comparados e relacionados com os dados de percepção própria do condutor, obtidos através dos testes subjectivos de auto-percepção NASA - Administração Nacional da Aeronáutica e do Espaço - Raw Task Load Index (NASA RTLX). É esperado que desta análise possam ser encontradas algumas conclusões que deverão indicar oportunidades de melhoria às interfaces das consolas centrais, que possam resultar de uma combinação ou divisão dos sistemas, ou que abram caminho ao desenvolvimento de novas soluções alternativas, ou até à criação de um guia de boas práticas para o futuro design e desenvolvimento de interfaces de consolas centrais para automóveis.

Point-wise confidence interval estimation by neural networks: A comparative study based on automotive engine calibration.

In developing neural network techniques for real world applications it is still very rare to see estimates of confidence placed on the neural network predictions. This is a major deficiency, especially in safety-critical systems. In this paper we explore three distinct methods of producing point-wise confidence intervals using neural networks. We compare and contrast Bayesian, Gaussian Process and Predictive error bars evaluated on real data. The problem domain is concerned with the calibration of a real automotive engine management system for both air-fuel ratio determination and on-line ignition timing. This problem requires real-time control and is a good candidate for exploring the use of confidence predictions due to its safety-critical nature.

Supplier competitive advantage in inter-firm business relationships:is Keiretsu really a source of competitive advantage for Japanese automotive suppliers?

This paper explores how firms create and sustain competitive advantage in the inter-firm business relationships from a supplier’s perspective. Ultimately, this paper draws its attention to keiretsu partnerships and how it is perceived by Japanese automotive suppliers. Four main theoretical perspectives (resource based view, industrial organisation, transaction cost economics, and relational network) were considered when developing a conceptual framework based on competitive capability, market diversification, and level of engagement. The framework was examined against two best-practice automotive component suppliers. Later, primary data was also gathered through an interview with a CEO and a survey questionnaire with 11 Japanese companies. As a result, this paper classified these 11 companies into four supplier groups based on tier level (1 and 2) and affiliation condition. Findings propose that there may be little benefit in being an affiliated tier 1 supplier, and that independent tier 2 suppliers may be more competitive than affiliated ones.

The importance of collaborative frontloading in automotive supply networks

Purpose – The purpose of this paper is to investigate how research and development (R&D) collaboration takes place for complex new products in the automotive sector. The research aims to give guidelines to increase the effectiveness of such collaborations. Design/methodology/approach – The methodology used to investigate this issue was grounded theory. The empirical data were collected through a mixture of interviews and questionnaires. The resulting inducted conceptual models were subsequently validated in industrial workshops. Findings – The findings show that frontloading of the collaborative members was a major issue in managing successful R&D collaborations. Research limitations/implications – The limitation of this research is that it is only based in the German automotive industry. Practical implications – Practical implications have come out of this research. Models and guidelines are given to help make a success of collaborative projects and their potential impacts on time, cost and quality metrics. Originality/value – Frontloading is not often studied in a collaborative manner; it is normally studied within just one organisation. This study has novel value because it has involved a number of different members throughout the supplier network.