Low-temperature sol-gel preparation of ordered nanoparticles of tungsten carbide/oxide

Tungsten carbide/oxide particles have been prepared by the gel precipitation of tungstic acid in the presence of an organic gelling agent [10% ammonium poly(acrylic acid) in water, supplied by Ciba Specialty Chemicals]. The feed solution; a homogeneous mixture of sodium tungstate and ammonium poly(acrylic acid) in water, was dropped from a 1-mm jet into hydrochloric acid saturated hexanol/concentrated hydrochloric acid to give particles of a mixture of tungstic acid and poly(acrylic acid), which, after drying in air at 100 degrees C and heating to 900 degrees C in argon for 2 h, followed by heating in carbon dioxide for a further 2 h and cooling, gives a mixture of WO, WC, and a trace of NaxWO3, with the carbon for the formation of WC being provided by the thermal carbonization of poly(acrylic acid). The pyrolyzed product is friable and easily broken down in a pestle and mortar to a fine powder or by ultrasonics, in water, to form a stable colloid. The temperature of carbide formation by this process is significantly lower (900 degrees C) than that reported for the commercial preparation of tungsten carbide, typically > 1400 degrees C. In addition, the need for prolonged grinding of the constituents is obviated because the reacting moieties are already in intimate contact on a molecular basis. X-ray diffraction, particle sizing, transmission electron microscopy, surface area, and pore size distribution studies have been carried out, and possible uses are suggested. A flow diagram for the process is described.

Mechanistic insights into a gas–solid reaction in molecular crystals: the role of hydrogen bonding

Reactions in (molecular) organic crystalline solids have been shown to be important for exerting control that is unattainable over chemical transformations in solution. Such control has also been achieved for reactions within metal– organic cages. In these examples, the reactants are already in place within the crystals following the original crystal growth. The post-synthetic modification of metal–organic frameworks (MOFs and indeed reactions and catalysis within MOFs have been recently demonstrated; in these cases the reactants enter the crystals through permanent channels. Another growing area of interest within molecular solid-state chemistry is synthesis by mechanical co-grinding of solid reactants—often referred to as mechanochemistry. Finally, in a small number of reported examples, molecules also have been shown to enter nonporous crystals directly from the gas or vapor phase, but in only a few of these examples does a change in covalent bonding result, which indicates that a reaction occurs within the nonporous crystals. It is this latter type of highly uncommon reaction that is the focus of the present study.

Chitosan-based mucoadhesive tablets for oral delivery of ibuprofen

Chitosan and its half-acetylated derivative have been compared as excipients in mucoadhesive tablets containing ibuprofen. Initially the powder formulations containing the polymers and the drug were prepared by either co-spray drying or physical co-grinding. Polymer–drug interactions and the degree of drug crystallinity in these formulations were assessed by infrared spectroscopy and differential scanning calorimetry. Tablets were prepared and their swelling and dissolution properties were studied in media of various pHs. Mucoadhesive properties of ibuprofen-loaded and drug-free tablets were evaluated by analysing their detachment from pig gastric mucosa over a range of pHs. Greater polymer–drug interactions were seen for spray-dried particles compared to co-ground samples and drug loading into chitosan-based microparticles (41%) was greater than the corresponding half-acetylated samples (32%). Swelling and drug release was greater with the half-acetylated chitosan tablets than tablets containing the parent polymer and both tablets were mucoadhesive, the extent of which was dependent on substrate pH. The results illustrate the potential sustained drug delivery benefits of both chitosan and its half-acetylated derivative as mucoadhesive tablet excipients.

Harnessing the ancestors: mutuality, uncertainty and ritual practice in the Eastern Cape Province, South Africa

In the Eastern Cape Province of South Africa, chronic economic uncertainty has seen social relations stretched to breaking point. Informants speak of a 'war between men and women'. While grinding poverty, death in the shape of the 'axe' (HIV/AIDS) and suspicion stalk the land, and the project of building the umzi (homestead) falters, hope for the future and with it, trust between people, leaches away. One response to such uncertainty is a turn to ritual. Through a nearly relentless schedule of ritual activity which invokes the ancestors and the Christian deity in various forms, Xhosa people attempt to dam up trust, secure ongoing investment in the rural homestead and sustain ties of reciprocity both among rural people and between them and their urban kin. It is also through the staging of these rituals that women, acting together and in support of each other, are increasingly assertive – often in the face of a violent, rearguard opposition from men - in their efforts to exercise agency over the differentiated, fragmented and fragile social and economic relationships within their homesteads and across their villages.

Mesenchymal Stem Cells and Bovine Bone Mineral in Sinus Lift Procedures-An Experimental Study in Sheep

Introduction: New reconstructive and less invasive methods have been searched to optimize bone formation and osseointegration of dental implants in maxillary sinus augmentation. Purpose: The aim of the presented ovine split-mouth study was to compare bovine bone mineral (BBM) alone and in combination with mesenchymal stem cells (MSCs) regarding their potential in sinus augmentation. Material and Methods: Bilateral sinus floor augmentations were performed in six adult sheep. BBM and MSCs were placed into the test side and only BBM in the contra-lateral control side of each sheep. Animals were sacrificed after 8 and 16 weeks. Augmentation sites were analyzed by computed tomography, histology, and histomorphometry. Results: The initial volumes of both sides were similar and did not change significantly with time. A tight connection between the particles of BBM and the new bone was observed histologically. Bone formation was significantly (p = 0.027) faster by 49% in the test sides. Conclusion: The combination of BBM and MSCs accelerated new bone formation in this model of maxillary sinus augmentation. This could allow early placement of implants.

Mesenchymal stem cells and inorganic bovine bone mineral in sinus augmentation: comparison with augmentation by autologous bone in adult sheep

Our aim was to compare the osteogenic potential of mononuclear cells harvested from the iliac crest combined with bovine bone mineral (BBM) (experimental group) with that of autogenous cancellous bone alone (control group). We studied bilateral augmentations of the sinus floor in 6 adult sheep. BBM and mononuclear cells (MNC) were mixed and placed into one side and autogenous bone in the other side. Animals were killed after 8 and 16 weeks. Sites of augmentation were analysed radiographically and histologically. The mean (SD) augmentation volume was 3.0 (1.0) cm(3) and 2.7 (0.3) cm(3) after 8 and 16 weeks in the test group, and 2.8 (0.3) cm(3) (8 weeks) and 2.8 (1.2) cm(3) (16 weeks) in the control group, respectively. After 8 weeks, histomorphometric analysis showed 24 (3)% BBM, and 19 (11)% of newly formed bone in the test group. The control group had 20 (13%) of newly formed bone. Specimens after 16 weeks showed 29 (12%) of newly formed bone and 19 (3%) BBM in the test group. The amount of newly formed bone in the control group was 16 (6%). The results show that mononuclear cells, including mesenchymal stem cells, in combination with BBM as the biomaterial, have the potential to form bone. (C) 2009 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Acellular dermal matrix as a barrier in guided bone regeneration: a clinical, radiographic and histomorphometric study in dogs

Objectives The purpose of this study was to evaluate the effectiveness of the acellular dermal matrix (ADM) as a membrane for guided bone regeneration (GBR), in comparison with a bioabsorbable membrane. Material and methods In seven dogs, the mandibular pre-molars were extracted. After 8 weeks, one bone defect was surgically created bilaterally and the GBR was performed. Each side was randomly assigned to the control group (CG: bioabsorbable membrane made of glycolide and lactide copolymer) or the test group (TG: ADM as a membrane). Immediately following GBR, standardized digital X-ray radiographs were taken, and were repeated at 8 and 16 weeks post-operatively. Before the GBR and euthanasia, clinical measurements of the width and thickness of the keratinized tissue (WKT and TKT, respectively) were performed. One animal was excluded from the study due to complications in the TG during wound healing; therefore, six dogs remained in the sample. The dogs were sacrificed 16 weeks following GBR, and a histomorphometric analysis was performed. Area measurements of new tissue and new bone, and linear measurements of bone height were performed. Results Post-operative healing of the CG was uneventful. In the TG membrane was exposed in two animals, and one of them was excluded from the sample. There were no statistically significant differences between the groups for any histomorphometric measurement. Clinically, both groups showed an increase in the TKT and a reduction in the WKT. Radiographically, an image suggestive of new bone formation could be observed in both groups at 8 and 16 weeks following GBR. Conclusion ADM acted as a barrier in GBR, with clinical, radiographic and histomorphometric results similar to those obtained with the bioabsorbable membrane. To cite this article:Borges GJ, Novaes AB Jr, de Moraes Grisi MF, Palioto DB, Taba M Jr, de Souza SLS. Acellular dermal matrix as a barrier in guided bone regeneration: a clinical, radiographic and histomorphometric study in dogs.Clin. Oral Impl. Res. 20, 2009; 1105-1115.

Influence of rhBMP-2 on bone formation and osseointegration in different implant systems after sinus-floor elevation. An in vivo study on sheep

Background Several studies have reported certain bone morphogenic proteins (BMPs) to have positive effects on bone generation Although some investigators have studied the effects of human recombinant BMP (rhBMP-2) in sinus augmentation in sheep, none of these studies looked at the placement of implants at the time of sinus augmentation Furthermore, no literature could be found to report on the impact that different implant systems, as well as the positioning of the implants had on bone formation if rhBMP-2 was utilized in sinus-lift procedures Purpose The aim of this study was to compare sinus augmentation with rhBMP-2 on a poly-D, L-lactic-co-glycolic acid gelatine (PLPG) sponge with sinus augmentation with autologous pelvic cancellous bone in the maxillary sinus during the placement of different dental Implants Materials and methods Nine adult female sheep were submitted to bilateral sinus-floor elevation In one side (test group) the sinus lift was performed with rhBMP-2 on a PLPG-sponge, while the contralateral side served as the control by using cancellous bone from the iliac crest Three different implants (Branemark (R), 31 (R) and Straumann (R)) were inserted either simultaneously with the sinus augmentation or as a two staged procedure 6 weeks later The animals were sacrificed at 6 and 12 weeks for histological and histomorphometrical evaluations during which bone-to-implant contact (BIC) and bone density (BD) were evaluated Results BD and BIC were significantly higher at 12 weeks in the test group if the Implants were placed at the time of the sinus lift (p < 0 05) No difference was observed between the different implant systems or positions Conclusions The use of rhBMP-2 with PLPG-sponge increased BIC as well as BD in the augmented sinuses if compared to autologous bone Different implant systems and positions of the implants had no effect on BIC or BD (C) 2010 European Association for Cranio-Maxillo-Facial Surgery

Immunohistochemical, tomographic and histological study on onlay iliac grafts remodeling

The information concerning the molecular events taking place in onlay bone grafts are still incipient. The objective of the present study is to correlate the effects of perforation of resident bone bed on (1) the timing of onlay autogenous graft revascularization; (2) the maintenance of volume/density of the graft (assessed through tomography); and (3) the occurrence of bone remodeling proteins (using immunohistochemistry technique) delivered in the graft. Thirty-six New Zealand White rabbits were subjected to iliac crest onlay bone grafting on both sides of the mandible. The bone bed was drill-perforated on one side aiming at accelerating revascularization, whereas on the other side it was kept intact. After grafts fixation and flaps suture all animals were submitted to tomography on both mandible sites. Six animals were sacrificed, respectively, at 3, 5, 7, 10, 20 and 60 days after surgery. A second tomography was taken just before sacrifice. Histological slides were prepared from each grafted site for both immunohistochemistry analysis [osteopontin, osteocalcin, type I collagen and vascular endothelial growth factor (VEGF) anti-bodies] and histometric analysis. The values on bone volume measured on tomography showed no statistic significance (P >= 0.05) between perforated and intact sites. Grafts placed on perforated beds showed higher bone density values compared with non-perforated ones at 3 days (P <= 0.05). This correlation was inverted at 60 days postoperatively. The findings from VEGF labeling revealed a tendency for earlier revascularization in the perforated group. The early revascularization of bone grafts accelerated the bone remodeling process (osteocalcin, type I collagen and osteopontin) that led to an increased bone deposition at 10 days. The extended osteoblast differentiation process at intermediate stages in the perforated group cooperated for a denser bone at 60 days.

Forebrain projections to brainstem nuclei involved in the control of mandibular movements in rats

Mandibular movements occur through the triggering of trigeminal motoneurons. Aberrant movements by orofacial muscles are characteristic of orofacial motor disorders, such as nocturnal bruxism (clenching or grinding of the dentition during sleep). Previous studies have suggested that autonomic changes occur during bruxism episodes. Although it is known that emotional responses increase jaw movement, the brain pathways linking forebrain limbic nuclei and the trigeminal motor nucleus remain unclear. Here we show that neurons in the lateral hypothalamic area, in the central nucleus of the amygdala, and in the parasubthalamic nucleus, project to the trigeminal motor nucleus or to reticular regions around the motor nucleus (Regio h) and in the mesencephalic trigeminal nucleus. We observed orexin co-expression in neurons projecting from the lateral hypothalamic area to the trigeminal motor nucleus. In the central nucleus of the amygdala, neurons projecting to the trigeminal motor nucleus are innervated by corticotrophin-releasing factor immunoreactive fibers. We also observed that the mesencephalic trigeminal nucleus receives dense innervation from orexin and corticotrophin-releasing factor immunoreactive fibers. Therefore, forebrain nuclei related to autonomic control and stress responses might influence the activity of trigeminal motor neurons and consequently play a role in the physiopathology of nocturnal bruxism.

Host-guest system of 4-nerolidylcatechol in 2-hydroxypropyl-beta-cyclodextrin: preparation, characterization and molecular modeling

The interaction of 4-nerolidylcatechol (4-NRC), a potent antioxidant agent, and 2-hydroxypropyl-beta-cyclodextrin (HP-beta-CD) was investigated by the solubility method using Fourier transform infrared (FTIR) methods in addition to UV-Vis, (1)H-nuclear magnetic resonance (NMR) spectroscopy and molecular modeling. The inclusion complexes were prepared using grinding, kneading and freeze-drying methods. According to phase solubility studies in water a B(S)-type diagram was found, displaying a stoichiometry complexation of 2:1 (drug:host) and stability constant of 6494 +/- A 837 M(-1). Stoichiometry was established by the UV spectrophotometer using Job`s plot method and, also confirmed by molecular modeling. Data from (1)H-NMR, and FTIR, experiments also provided formation evidence of an inclusion complex between 4-NRC and HP-beta-CD. 4-NRC complexation indeed led to higher drug solubility and stability which could probably be useful to improve its biological properties and make it available to oral administration and topical formulations.

Wear of coated and uncoated PCBN cutting tool used in turning and milling

This licentiate thesis has the main focus on evaluation of the wear of coated and uncoated polycrystalline cubic boron nitride cutting tool used in cutting operations against hardened steel. And to exam the surface finish and integrity of the work material used. Harder work material, higher cutting speed and cost reductions result in the development of harder and more wear resistance cutting tools. Although PCBN cutting tools have been used in over 30 years, little work have been done on PVD coated PCBN cutting tools. Therefore hard turning and hard milling experiments with PVD coated and uncoated cutting tools have been performed and evaluated. The coatings used in the present study are TiSiN and TiAlN. The wear scar and surface integrity have been examined with help of several different characterization techniques, for example scanning electron microscopy and Auger electron spectroscopy.   The results showed that the PCBN cutting tools used displayed crater wear, flank wear and edge micro chipping. While the influence of the coating on the crater and flank wear was very small and the coating showed a high tendency to spalling. Scratch testing of coated PCBN showed that, the TiAlN coating resulted in major adhesive fractures. This displays the importance of understanding the effect of different types of lapping/grinding processes in the pre-treatment of hard and super hard substrate materials and the amount and type of damage that they can create. For the cutting tools used in turning, patches of a adhered layer, mainly consisting of FexOy were shown at both the crater and flank. And for the cutting tools used in milling a tribofilm consisting of SixOy covered the crater. A combination of tribochemical reactions, adhesive wear and mild abrasive wear is believed to control the flank and crater wear of the PCBN cutting tools. On a microscopic scale the difference phases of the PCBN cutting tool used in turning showed different wear characteristics. The machined surface of the work material showed a smooth surface with a Ra-value in the range of 100-200 nm for the turned surface and 100-150 nm for the milled surface. With increasing crater and flank wear in combination with edge chipping the machined surface becomes rougher and showed a higher Ra-value. For the cutting tools used in milling the tendency to micro edge chipping was significant higher when milling the tools steels showing a higher hard phase content and a lower heat conductivity resulting in higher mechanical and thermal stresses at the cutting edge.

Estudo de pelotização e briquetagem de finos de carvão mineral

O aumento da produção de carvão previsto para os próximos anos nas minas da CRM localizadas em Leão, Butiá, RS, originará uma considerável quantidade de finos beneficiados por ciclonagem autôgena. Estes finos caracterizam-se pelos seus altos teores de umidade e granulometria <1 mm o que onera e dificulta os processos de manuseio, estocagem e transporte. O presente estudo visa à análise comparativa dos processos de aglomeração, a briquetagem e a pelotização com o objetivo de obter um produto com melhores características de comercialização do que o atual. As principais variáveis estudadas na aglomeração por briquetagem foram: teor de umidade, tipo e concentração de agente ligante, relação massa/volume de carvão, tempo e pressão de moldagem. Os melhores resultados em termos de resistência à compressão, foram obtidos utilizando um resíduo de refinaria de petróleo - REVAC - como ligante numa concentração de 10% em peso, uma temperatura de cura de 120° C, um tempo de moldagem de 0,5 minutos e uma pressão de compactação entre 150 e 250 kgf/cm². A pelotização foi estudada utilizando um tambor e um disco de laboratório e as principais variáveis estudadas foram: umidade da alimentação, tipo e concentração de agente ligante, temperatura de cura e outras. Os melhores resultados foram obtidos utilizando como ligante MOGUL (amido de milho pré-gelatinizado em pó) numa concentração de 5% em peso, uma faixa de umidade ótima entre 30 e 40%, uma inclinação do disco entre 45 e 51° e uma temperatura de cura de 80 e 100°C. Os resultados obtidos para ambos os carvões (CE 5900 e CE 4700) são discutidos em termos dos diversos fenômenos que ocorrem na interface carvão-solução-ligante e algumas considerações econômicas são apresentadas.

Estudo sobre a potencialidade de uso das escórias de aciaria como adição ao concreto

A geração de resíduos tem se mostrado um problema de preocupação mundial crescente. Muitos rejeitos, sejam industriais ou urbanos, muitas vezes acabam por poluir o meio-ambiente, causando problemas de armazenagem de certos materiais. Além disso, materiais alternativos a partir desses rejeitos podem ser mais baratos, apresentando muitas vezes características de desempenho melhores que os materiais convencionais. As siderúrgicas, em nível mundial, vêm enfrentando um problema comum, que consiste no que fazer para que a totalidade da escória gerada no refino do aço em aciarias elétricas ou à oxigênio tenha uma solução de aproveitamento melhor do que vem sendo feito atualmente. Na fabricação do aço as escorias são geradas em duas etapas: a primeira provém do chamado refino oxidante (forno elétrico a arco ou convertedor à oxigênio) e a segunda do refino redutor em processos de metalurgia na panela (forno-panela). Este trabalho tem como objetivo principal o de apontar potencialidades de uso da escória de aciaria elétrica, com destaque para a proveniente do forno-panela (escória do refino redutor), na indústria da construção civil através de testes em que a escória é utilizada, após moagem, como adição ao cimento Portland comum. Inicialmente foram realizados ensaios de viabilização para se testar a pozolanicidade, resistência à compressão, expansibilidade e profundidade de carbonatação de concretos gerados com diversas adições de escórias de aciaria elétrica. Comprovada a sua viabilidade partiu-se para os ensaios complementares do trabalho utilizando-se somente uma escória do refino redutor. Nesta segunda etapa foram realizados ensaios de caracterização de todos materiais estudados, ensaios de expansibilidade, ensaios mecânicos e de durabilidade dos concretos gerados com esta escória e ensaios de microscopia eletrônica de varredura e de difração de raios X do material. Após o estudo realizado comprovou-se ser perfeitamente viável a utilização de até 10% da escória do refino redutor (forno-panela- FP) como adição ao cimento para produção de concretos. Inclusive, independente do tempo de estocagem da escória, pode-se constatar melhorias no concreto produzido.

Contribuição ao beneficiamento de finos de fosfatos

Foram estudadas as características de floculação da hidro-xiapatita, calcita e quartzo com poliacrilamidas aniônicas. Tanto as suspensões de hidroxiapatita como a calcita foram completamente floculadas enquanto que o quartzo foi refratário a floculação com esses polimeros. Entretanto, observou-se que a floculação da calcita foi impedida com a utilização de um poliacrilato de sódio, enquanto que a hidroxiapatita continuou a ser floculada pela poliacrilamida num intervalo de concentração de O a 1000 g/ton de poliacrilato. Estes resultados permitiram estabelecer condições para a floculação seletiva de hidroxiapatita em misturas sintéticas com quartzo e calcita. Nestes sistemas foram estudados diversos parâmetros operacionais, tais como tipo de separação, efeito do teor da alimentação, e influência da moagem. Onde a separação estagiada apresentou melhor resultado, uma moagem adicional no sistema não favoreceu a seletividade. Por outro lado, o teor de P205 no concentrado é proporcional ao teor presente na alimentação. A hidroxiapatita, em estudo, de alta pureza (de acordo com técnicas de análise química, espectrofotometria de infravermelho e difração de raios X) apresentou um parto de carga zero em pH 6,77 na presença de diversos eletrólitos. A aplicação do sistema de floculação seletiva a fraçoes ultrafinas industriais foi estudada em detalhe e comparada com processos de flotação e floco-flatação. 0s resultados obtidos mostraram que a floculação seletiva somente foi eficiente nos sistemas sintéticos. A flotação, embora o minério apresente uma granulometria muito fina, foi mais eficiente que a floculação seletiva e a floco-flotação nos sistemas reais, em termos de taxa de enriquecimento e percentual de rejeição de massa. Entretanto com a floco-flotação foi possivel obter altas recuperações(-90%) para os minérios de Araxá e Itataia. Para o minério de Tapira, um aumento do teor de P2O5 foi obtido com a flotação da fração seletivamente floculada. As taxas de enriquecimento obtidas foram baixas (entre 1,35 e 2,101 em função das associações entre a apatita do minério com óxido de ferro e argila, o que revelou a caracterização mineralógica. Conclue-se que a concentração de minerios fosfatados de baixo teor é uma operação onerosa, onde o fator predominante é a absorção seletiva de reagentes e atransferência não específica de material de ganga nos respectivos concentrados.