Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Study of porcelain-zirconia composites for dental applications

Materiais compósitos restauradores representam um dos mais bem sucedidos biomateriais na pesquisa moderna, na substituição do tecido biológico em aparência e função. Nesta linha, a porcelana feldspática tem sido largamente usada em odontologia devido suas interessantes qualidades como estabilidade de cor, propriedades estéticas, elevada durabilidade mecânica, biocompatibilidade, baixa condutividade térmica e elevada resistência ao desgaste. Entretanto, este material é frágil e pode falhar em ambiente oral devido ao micro-vazamento, baixa resistência à tração, descolagem ou fratura. Assim, para melhorar as propriedades mecânicas da porcelana, a zircônia parcialmente estabilizada com Ítria (Y-TZP) pode ser uma boa alternativa para fortalecer e produzir infraestruturas totalmente cerâmicas (coroas e próteses parciais fixas). Portanto, este estudo tem por objetivo avaliar as propriedades mecânicas e características microestruturais da porcelana reforçada com zircônia (3Y-TZP) em diferentes conteúdos e as variáveis que afetam as propriedades mecânicas destes materiais. O estudo de caracterização revelou que a zircônia comercial apresenta melhores resultados quando comparada com a zircônia sintetizada pelo CPM. Assim, os estudos seguintes utilizaram a zircônia comercial para todos os testes requeridos. As partículas de zircônia apresentam elevadas propriedades mecânicas quando comparadas a zircônia aglomerada. Os diferentes conteúdos revelam que as propriedades mecânicas dos compósitos aumentam com o aumento do conteúdo volumétrico até 30% vol.% (198,5Mpa), ou seja, maior resistência à flexão quando comparada com os outros compósitos. Do mesmo modo, a resistência ao desgaste para os compósitos com (30%, vol.% de zircônia) apresenta valores superiores quando comparado aos demais compósitos. Na adesão cerâmico-cerâmico a porcelana exibe elevada adesão para a superfície de zircônia porosa quando comparada a superfície rugosa. Os furos superficiais (PZ) e aplicação de compósitos com camada intermediária (RZI) na zircônia causam separadamente uma melhoria da resistência ao cisalhamento da zircônia-porcelana quando comparados as amostras convencionais de zircônia-porcelana (RZ), embora não sejam estatisticamente significativas (p>0.05). A presença de uma camada intermediaria produz um aumento significativo na força de ligação (~55%) em relação as amostras convencionais (RZ). Portanto, a correta a correta configuração e tratamento superficial podem produzir subestruturas com qualidade e força de ligação adequadas aos requisitos odontológicos.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

La cerámica del yacimiento arqueológico de Castillejo del Bonete (Terrinches, Ciudad Real). Estudio morfológico y tecnólogico

El presente trabajo incluye el estudio de un amplio conjunto cerámico perteneciente al yacimiento arqueológico de la Edad del Cobre y Edad del Bronce de Castillejo del Bonete. La muestra fue recuperada de distintas áreas del asentamiento durante la campaña de excavación de 2012. La investigación ha tenido como fin conocer mejor la relación forma-función de las vasijas, su proceso de fabricación, así como el modelo productivo y las posibles manifestaciones simbólicas presentes en el repertorio analizado. La metodología utilizada para cumplir con los objetivos se ha basado en la recopilación de datos, considerando una serie de variables morfológicas y tecnológicas, y su procesamiento con el empleo de técnicas estadísticas sencillas.

La estructuración del espacio urbano y productivo de Gadir durante la fase urbana clásica: Cambios y perduraciones

La reafirmación del modelo político-administrativo ciudadano tras la fase arcaica colonial abre una nueva etapa de prosperidad en la antigua fundación tiria. El esplendor de Gadir en el s. V a.C. se refleja en los textos clásicos y en los hallazgos arqueológicos y, sin embargo, nuestros conocimientos sobre el desarrollo histórico de la ciudad de época púnica son muy limitados. El horizonte arcaico comienza a esclarecerse tras los hallazgos del Teatro Cómico que han sacado a la luz los restos de la fundación tiria y, sin embargo, la ciudad posterior continúa siendo una gran incógnita. ¿A qué lugar se traslada la población una vez que se abandona el asentamiento primitivo? ¿Quiénes son los individuos enterrados en los excepcionales sarcófagos antropoides? ¿Qué relación jerárquica existe entre el asentamiento insular y los situados en tierra firme? ¿Qué papel jugó la industria y comercialización de las salazones? Los interrogantes planteados son múltiples y no hacen más que evidenciar la incapacidad del paradigma tradicional para explicar el desarrollo histórico de la Gadir postcolonial y la necesidad de buscar nuevos modelos interpretativos.

Desde una arqueología inclusiva, por un pasado mejor. Un ensayo epistemológico y axiológico

En este trabajo se reflexiona sobre la necesidad de un marco epistemológico inclusivo que aborde la multivocalidad de los procesos históricos objeto de estudio y permita crear relatos históricos más plurales y representativos. Pero el relato sobre el pasado será mejor si, además de ser inclusivo a nivel epistemológico, también contribuye de alguna manera a mejorar la sociedad actual. Por ello se reclama una arqueología que incluya una preocupación axiológica y busque posibles ámbitos de aplicación para los resultados de sus investigaciones. Ejemplificamos esta reivindicación con un caso de estudio sobre cerámica, que subraya que los objetos cotidianos fueron y son utilizados en las estrategias de construcción social de la desigualdad. En este contexto se reclama la toma de consciencia de esta práctica en la actualidad y la renuncia a determinados recursos discursivos. Por ejemplo, se propone retomar el concepto inclusivo, este vez para oponerlo a la significación social del adjetivo exclusivo. Aunque todas estas reflexiones derivan de casos de estudio de arqueología histórica, pueden ser útiles a la arqueología en general, sin sesgo cronológico alguno.

Source Provenance of Pre-Historic Granitic Grindstones: The Case Study of the Cogotas I Archaeological Site of Arroyo Mucientes/San Lázaro (Castronuño, Valladolid) and a Proposal on the General Methodological Flow Process

The occurrence of hand grindstones at the Cogotas I archaeological sites is considered to be a common feature. Given that a distant-provenance raw material is frequently involved, determination of its source is a basic factor in the search for a better understanding of resource management and for any Political Economy approach. To progress in these directions an overall study should be planned, using selected grindstones with a view to covering diverse sub-zones of the Cogotas I dispersal area, especially because of its considerable distance from the granite basement source. Such a study may today includes diverse analytical procedures combining successive geographic, petrographic, mineralogical and geochemical criteria. To check the plausibility of the proposed methodology, a preliminary test has been carried out on two granite grindstones, obtained at the archaeological excavation at the Castronuño (Valladolid) Cogotian site, which is fifty km away from an inferred source area that was presumably located at Peñausende (Zamora). The result obtained validates the proposed operational process, yielding a generalizable knowledge to other similar situations.

Late Bronze Age in Eastern Iberian Peninsula: Archaeological Bases and Periodization

Research surrounding the transition from II to I millennium cal BC in Eastern Iberian Peninsula has a large and extensive tradition of investigation. However, the chances to do research on this historical process have been limited by the lack of a well contextualized and dated stratigraphic sequence. For this reason, recent studies in this topic have followed the periodic proposals which were developed in closer regions and areas, especially in the South East and North East of the Peninsula. The investigation perspective about the Late Bronze in Eastern Iberian has however now improved, with the development of several archaeological investigations, the increase in the number of sites being dated and more recent studies into the region helping to bring about this change. As such, it is now in the correct state to be able to propose a new periodization and delve into the changes which occurred in the transition between 1500 and 725 cal BC.

"Lancea", Lusitanian Word, and the "Lancienses" Ethnogenesis

Analysis of the word lancea, of Hispanic origin after Varro, and of place names, people´s names and personal names derived from it. It confirms that the spear was the most important weapon in the Bronze Age, belonging to the iuventus and used as heroic and divine symbol. This analysis confirms also the personality of the Lusitanians, a people related to the Celts but with more archaic archaeological, linguistic and cultural characteristics originated in the tradition of the Atlantic Bronze in the II millennium BC. It is also relevant to better know the organisation of Broze and Iron Age societies and the origin of Indo-Europeans peoples in Western Europe and of pre-Roman peoples of Iberia.

Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial

VARELA, M. L. et al. Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial. Cerâmica, v.55, n.334 p.209-215. 2009.ISSN 0366-6913.Disponível em: . Acesso em: 06 out. 2010.

Produzione di micro-supercapacitori allo stato semisolido per applicazioni portatili

La seguente tesi prevede la costruzione e caratterizzazione di un micro-supercapacitore asimmetrico composto da un anodo a base di ZnO ed un catodo a base di grafene ossido ridotto (rGO); la combinazione di due materiali con differente natura di accumulo di carica permette quindi di ottenere dispositivi con migliori performance elettrochimiche. Entrambi gli elettrodi sono stati depositati per via elettrochimica su substrati flessibili di PET-ITO. L'ottimizzazione delle proprietà dello ZnO è stata fatta tramite l'aggiunta di molecole di tensioattivi durante la deposizione dello stesso. I risultati ottenuti mostrano un effettivo miglioramento delle proprietà elettrochimiche e della trasparenza dei film di ZnO prodotto grazie all'effetto di tali tensioattivi. Inoltre anche le proprietà di rGO sono state ottimizzate allo scopo di ottenere buone proprietà elettrochimiche abbinate all'elevata trasparenza del film prodotto. Infine sono stati costruiti micro-supercapacitori allo stato semisolido con differenti agenti gelificanti (silice e Nanoclay) ed il loro funzionamento è stato dimostrato.

Propriedades óticas dos sistemas cerâmicos atuais e suas aplicações em dentes naturais

A estética representa uma qualidade cada vez mais requisitada pela sociedade na atualidade. A busca pela aparência ideal expandiu-se também na medicina dentária, aumentando as exigências por resultados perfeitos. A medicina dentária tem desenvolvido novas técnicas e novos materiais com a ambição de reproduzir as propriedades estéticas e funcionais dos dentes naturais. Os sistemas totalmente cerâmicos têm sido alvo de grande entusiasmo dado as suas características inerentes. O seu potencial na reabilitação oral estética tem derrotado as suas antecessoras metalocerâmicas. À semelhança do esmalte e da dentina, os sistemas totalmente cerâmicos exibem boas propriedades óticas de translucidez, opacidade, fluorescência e opalescência, resultado da interação com a luz. Ainda que não seja possível dissociar as propriedades óticas das propriedades mecânicas de um dente natural para o sucesso de uma restauração, a heterogeneidade das cerâmicas têm sido exitosas enquanto sistema que combina diferentes propriedades para diferentes indicações clínicas. Esta variabilidade deve-se a diferentes composições químicas e a diferentes processos de fabricação, entre outros, que acentuam ou atenuam qualidades em cada sistema totalmente cerâmico. Este trabalho pretende abordar e comparar os sistemas cerâmicos atuais (cerâmicas com base em sílica, cerâmicas com base de alumina, cerâmicas com base em zircónia) de acordo com as suas propriedades óticas e a consequente aplicação clínica tendo em conta as características dos dentes naturais.

Economía en el maquinado para la industria metalmecánica.

Este artículo presenta un estudio sobre la economía en el proceso de maquinado para minimizar los costos por unidad y maximizar la velocidad de producción. Se analizaron tres materiales típicos en las herramientas de corte: acero de alta velocidad,carburo cementado y cerámico. Se encontró que las herramientas de material cerámico poseen menor costo por unidad y menor duración del ciclo que las herramientas de carburo cementado y que las herramientas de acero rápido. Las herramientas desechables presentaron menor tiempo por ciclo y menor costo por pieza que las herramientas reafilables.