Alternating current conduction behavior of excimer laser ablated SrBi2Nb2O9 thin films

Bi-layered Aurivillius compounds prove to be efficient candidates of nonvolatile memories. SrBi2Nb2O9 thin films were deposited by excimer laser ablation at low substrate temperature (400 °C) followed by an ex situ annealing at 750 °C. The polarization hysteresis behavior was confirmed by variation of polarization with the external applied electric field and also verified with capacitance versus voltage characteristics. The measured values of spontaneous and remnant polarizations were, respectively, 9 and 6 μC/cm2 with a coercive field of 90 kV/cm. The measured dielectric constant and dissipation factors at 100 kHz were 220 and 0.02, respectively. The frequency analysis of dielectric and ac conduction properties showed a distribution of relaxation times due to the presence of multiple grain boundaries in the films. The values of activation energies from the dissipation factor and grain interior resistance were found to be 0.9 and 1.3 eV, respectively. The deviation in these values was attributed to the energetic conditions of the grain boundaries and bulk grains. The macroscopic relaxation phenomenon is controlled by the higher resistive component in a film, such as grain boundaries at lower temperatures, which was highlighted in the present article in close relation to interior grain relaxation and conduction properties.

Online Handwritten Kannada Word Recognizer with Unrestricted Vocabulary

In this paper, we propose a novel heuristic approach to segment recognizable symbols from online Kannada word data and perform recognition of the entire word. Two different estimates of first derivative are extracted from the preprocessed stroke groups and used as features for classification. Estimate 2 proved better resulting in 88% accuracy, which is 3% more than that achieved with estimate 1. Classification is performed by statistical dynamic space warping (SDSW) classifier which uses X, Y co-ordinates and their first derivatives as features. Classifier is trained with data from 40 writers. 295 classes are handled covering Kannada aksharas, with Kannada numerals, Indo-Arabic numerals, punctuations and other special symbols like $ and #. Classification accuracies obtained are 88% at the akshara level and 80% at the word level, which shows the scope for further improvement in segmentation algorithm

Thermal Management of Electronics Using PCM-Based Heat Sink Subjected to Cyclic Heat Load

Designing a heat sink based on a phase change material (PCM) under cyclic loading is a critical issue. For cyclic operation, it is required that the fraction of the PCM melting during the heating cycle should completely resolidify during the cooling period, so that that thermal storage unit can be operated for an unlimited number of cycles. Accordingly, studies are carried out to find the parameters influencing the behavior of a PCM under cyclic loading. A number of parameters are identified in the process, the most important ones being the duty cycle and heat transfer coefficient (h) for cooling. The required h or the required cooling period for complete resolidification for infinite cyclic operation of a conventional PCM-based heat sink is found to be very high and unrealistic with air cooling from the surface. To overcome this problem, the conventional design is modified where h and the area exposed to heat transfer can be independently controlled. With this arrangement, the enhanced area provided for cooling keeps h within realistic limits. Analytical investigation is carried out to evaluate the thermal performance of this modified PCM-based heat sink in comparison to those with conventional designs. Experiments are also performed on both the conventional and the modified PCM-based heat sinks to validate the new findings.

Composition of Extrafloral Nectar Influences Interactions between the Myrmecophyte Humboldtia brunonis and its Ant Associates

Ant-plant interactions often are mediated by extrafloral nectar (EFN) composition that may influence plant visitation by ants. Over a 300 km range in the Indian Western Ghats, we investigated the correlation between the EFN composition of the myrmecophytic ant-plant Humboldtia brunonis (Fabaceae) and the number and species of ants visiting EFN. EFN composition varied among H. brunonis populations and between plant organs (floral bud vs. young leaf EFN). In general, EFN was rich in sugars with small quantities of amino acids, especially essential amino acids, and had moderate invertase activity. In experiments at the study sites with sugar and amino acid solutions and with leaf or floral bud EFN mimics, dominant EFN-feeding ants differentiated between solutions as well as between mimics. The castration parasite Crematogaster dohrni (northern study site) was the least selective and did not exhibit any clear feeding preferences, while the largely trophobiont-tending non-protective Myrmicaria brunnea (middle study site) preferred higher sucrose concentrations and certain essential/non-essential amino acid mixtures. The mutualistic Technomyrmex albipes (southern study site) preferred sucrose over glucose or fructose solutions and consumed the leaf EFN mimic to a greater extent than the floral bud EFN mimic. This young leaf EFN mimic had low sugar concentrations, the lowest viscosity and sugar: amino acid ratio, was rich in essential amino acids, and appeared ideally suited to the digestive physiology of T. albipes. This preference for young leaf EFN may explain the greater protection afforded to young leaves than to floral buds by T. albipes, and may also help to resolve ant-pollinator conflicts. The differential response of dominant ants to sugar, amino acids, or solution viscosity suggests that plants can fine-tune their interactions with local ants via EFN composition. Thus, EFN can mediate local partner-choice mechanisms in ant-plant interactions.

Activation of Lattice Oxygen of TiO2 by Pd2+ Ion: Correlation of Low-Temperature CO and Hydrocarbon Oxidation with Structure of Ti1-xPdxO2-x (x=0.01-0.03)

Lattice oxygen of TiO2 is activated by the substitution of Pd ion in its lattice. Ti1-xPdxO2-x (x = 0.01-0.03) have been synthesized by solution combustion method crystallizing in anatase TiO2 structure. Pd is in +2 oxidation state and Ti is in +4 oxidation state in the catalyst. Pd is more ionic in TiO2 lattice compared to Pd in PdO. Oxygen storage capacity defined by ``amount of oxygen that is used reversibly to oxidize CO'' is as high as 5100 mu mol/g of Ti0.97Pd0.03O1.97. Oxygen is extracted by CO to CO2 in absence of feed oxygen even at room temperature which is more than 20 times compared to pure TiO2. Rate of CO oxidation is 2.75 mu mol g(-1) s(-1) at 60 degrees C over Ti0.97Pd0.03O1.97 and C2H2 gets oxidized to CO2 and H2O at room temperature. Catalyst is not poisoned on long time operation of the reactor. Such high catalytic activity is due to activated lattice oxygen created by the substitution of Pd ion as seen from first-principles density functional theory (DFT) calculations with 96 atom supercells of Ti32O64, Ti31Pd1O63, Ti30Pd2O62, and Ti29Pd3O61. The compounds crystallize in anatase TiO2 structure with Pd2+ ion in nearly square planar geometry and TiO6 octahedra are distorted by the creation of weakly bound oxygens. Structural analysis of Ti31Pd1O63 which is close to 3% Pd ion substituted TiO2 shows that oxygens associated with both Ti and Pd ions in the lattice show bond valence sum of 1.87, a low value characteristic of weak oxygen in the lattice compared to oxygens with valence 2 and above in the same lattice. Exact positions of activated oxygens have been identified in the lattice from DFT calculations.

A GIS (geographical information system)-based spatial data mining approach for optimal location and capacity planning of distributed biomass power generation facilities: A case study of Tumkur district, India

This paper primarily intends to develop a GIS (geographical information system)-based data mining approach for optimally selecting the locations and determining installed capacities for setting up distributed biomass power generation systems in the context of decentralized energy planning for rural regions. The optimal locations within a cluster of villages are obtained by matching the installed capacity needed with the demand for power, minimizing the cost of transportation of biomass from dispersed sources to power generation system, and cost of distribution of electricity from the power generation system to demand centers or villages. The methodology was validated by using it for developing an optimal plan for implementing distributed biomass-based power systems for meeting the rural electricity needs of Tumkur district in India consisting of 2700 villages. The approach uses a k-medoid clustering algorithm to divide the total region into clusters of villages and locate biomass power generation systems at the medoids. The optimal value of k is determined iteratively by running the algorithm for the entire search space for different values of k along with demand-supply matching constraints. The optimal value of the k is chosen such that it minimizes the total cost of system installation, costs of transportation of biomass, and transmission and distribution. A smaller region, consisting of 293 villages was selected to study the sensitivity of the results to varying demand and supply parameters. The results of clustering are represented on a GIS map for the region.

Memory effect in SrRu(1-x)O3 (0.01 < x < 0.07)

SrRuO3 is widely known to be an itinerant ferromagnet with a T-C similar to 160 K. It is well known that glassy materials exhibit time dependent phenomena such as memory effect due to their generic slow dynamics. However, for the first time, we have observed memory effect in SrRu(1-x)O3 (0.01

Critical investigation on hydrogen bonding by Fourier transform infrared spectroscopy in hydrogenated amorphous silicon thin films

Fourier Transform Infrared (FTIR) spectroscopic analysis has been carried out on the hydrogenated amorphous silicon (a-Si:H) thin films deposited by DC, pulsed DC (PDC) and RF sputtering process to get insight regarding the total hydrogen concentration (C-H) in the films, configuration of hydrogen bonding, density of the films (decided by the vacancy and void incorporation) and the microstructure factor (R*) which varies with the type of sputtering carried out at the same processing conditions. The hydrogen incorporation is found to be more in RF sputter deposited films as compared to PDC and DC sputter deposited films. All the films were broadly divided into two regions namely vacancy dominated and void dominated regions. At low hydrogen dilutions the films are vacancy dominated and at high hydrogen dilutions they are void dominated. This demarcation is at C-H = 23 at.% H for RF, C-H = 18 at.% H for PDC and C-H = 14 at.% H for DC sputter deposited films. The microstructure structure factor R* is found to be as low as 0.029 for DC sputter deposited films at low C-H. For a given C-H, DC sputter deposited films have low R* as compared to PDC and RF sputter deposited films. Signature of dihydride incorporation is found to be more in DC sputter deposited films at low C-H.

Algal biofuel: bountiful lipid from Chlorococcum sp proliferating in municipal wastewater

Algae biofuel have emerged as viable renewable energy sources and are the potential alternatives to fossil-based fuels in recent times. Algae have the potential to generate significant quantities of commercially viable biofuel apart from treating wastewater. Three algal species, viz. Chlorococcum sp., Microcystis sp. and Phormidium sp. proliferating in wastewater ponds were isolated and cultured in the laboratory myxotrophically under similar wastewater conditions. Chlorococcum sp. attained a mean biomass productivity of 0.09 g. I(-1)d(-1) with the maximum `biomass density of 1.33 g I-1 and comparatively higher lipid content of 30.55% (w/w) on the ninth day of the culture experiment. Under similar conditions Microcystis sp. and Phormidium sp. attained mean biomass productivities of 0.058 and 0.063 g I-1 d(-1) with a total lipid content of 8.88% and 18.66% respectively. Biochemical composition (carbohydrates, proteins, lipids and phosphates) variations and lipid accumulation studies were performed by comparison of the ratios of carbohydrate to protein; lipid to protein (L/P) and lipid to phosphates using attenuated total reflectance-Fourier transform infrared spectroscopy which showed higher L/P ratio during the stationary phase of algal growth. Composition analysis of fatty acid methyl ester has been performed using gas chromatography and mass spectrometry. Chlorococcum sp. with higher productivity and faster growth rate has higher lipid content with about 67% of saturated fatty acid dominated by palmitate (36.3%) followed by an unsaturate as linoleate (14%) and has proved to be an economical and viable feedstock for biofuel production compared to the other wastewater-grown species.

Role of melt convection on optimization of PCM-based heat sink under cyclic heat load

In this article, we study the thermal performance of phase-change material (PCM)-based heat sinks under cyclic heat load and subjected to melt convection. Plate fin type heat sinks made of aluminum and filled with PCM are considered in this study. The heat sink is heated from the bottom. For a prescribed value of heat flux, design of such a heat sink can be optimized with respect to its geometry, with the objective of minimizing the temperature rise during heating and ensuring complete solidification of PCM at the end of the cooling period for a given cycle. For given length and base plate thickness of a heat sink, a genetic algorithm (GA)-based optimization is carried out with respect to geometrical variables such as fin thickness, fin height, and the number of fins. The thermal performance of the heat sink for a given set of parameters is evaluated using an enthalpy-based heat transfer model, which provides the necessary data for the optimization algorithm. The effect of melt convection is studied by taking two cases, one without melt convection (conduction regime) and the other with convection. The results show that melt convection alters the results of geometrical optimization.

Eu3+-activated SrMoO4 phosphors for white LEDs applications: Synthesis and structural characterization

We report the synthesis of Eu3+-activated SrMoO4 phosphors by the facile nitrate-citrate gel combustion method. Powder XRD and Rietveld refinement data confirmed that these phosphors have a monophasic scheelite-type tetragonal structure with space group I4(1)/a (No. 88). FESEM micrographs indicate the agglomerated spherical particles. FTIR spectra showed four stretching and bending vibrational modes (2A(u) and 2E(u)). UV-Visible absorption spectroscopy illustrated that the optical band gap energy (E-g) values increase with increase in Eu3+ concentration. The host SrMoO4 phosphor exhibited an intense blue emission under UV excitation (368 nm). The Eu3+-activated SrMoO4 phosphors revealed characteristic luminescence due to Eu3+ ion corresponding to D-5(1) -> F-7(J) (J = 1,2) and D-5(0) -> F-7(J) (J = 1,2,3,4) transitions upon 465 nm excitation. The electric dipole transition located at 615 nm (D-5(0) -> F-7(2)) was stronger than the magnetic dipole transition located at 592 nm (D-5(0) -> F-7(1)). Intensity parameters (Omega(2), Omega(4)) and radiative properties such as transition probabilities (A(T)), radiative lifetime (tau(rad)) and branching ratio (beta) of Eu3+-activated SrMoO4 phosphors were calculated using the Judd-Ofelt theory. Based on the CIE chromaticity diagram, these phosphors can be promising materials for the development of blue and orange-red component in white LEDs. (C) 2015 Elsevier B.V. All rights reserved.

Evaluación financiera de la explotación apícola El Jobo, en el municipio de San Ramón, departamento de Matagalpa (Período Julio 1999 - Junio 2000)

El Presente trabajo se llevó a cabo en la finca El Jobo en los Apiarios Propiedad de CODAPI, la finca se ubica en el Municipio de San Ramón, carretera Pancasan, Matlguas en las coordenadas 12" 55' Latitud Norte y 85" 55' Longitud Oeste con una altura de 640 msnm y una Temperatura de 20- 26" C. El clima existente se clasifica de Trópico semi húmedo con bosque perenne y una flora útil para la Apicultura. La época seca se presenta de Febrero a mayo y un periodo lluvioso de Junio - Enero, con una precipitación de 2000 - 2400 mm /ano. Para el levantamiento de la información se realizó un estudio de casos con entrevistas semi - estructuradas, a lo largo del ciclo apícola 1999-2000, con visitas quincenales, que permitieron conocer el manejo de los apiarios, producción de miel y los costos de producción. El análisis de la información permitió evaluar el calendario apícola, los costos de producción divididos en mano de obra, insumos, servicios; así como determinar parámetros productivos como kilogramos de miel por ciclo, por apiario, por colmena. Se calcularon además la relación beneficio costo, margen bruto por apiario, margen bruto por colmena y margen bruto por dial hombre. Los resultados indicaron que la estrategia de producción principal de este ciclo fue la producción de colonias, aprovechando la flor amarilla, miel que no tiene demanda en el mercado internacional, no obstante permitió salvar el ciclo. Una vez realizada la evaluación financiera se pudo determinar que la relación beneficio - costo de este ciclo apícola fue de 0.88. Entre los factores que influyeron en estos resultados se pueden mencionar: La falta de capacitación en el manejo gerencial, administrativo y financiero del apiario. Factores climatológicos como fuertes vientos durante la época seca deshidrataron la flora. La no realización de un calendario apícola después del Huracán Mitch que dejó desvastada la flora de la zona norte del País, lo cual incidió de forma significativa en la producción de miel al momento de la trashumancia. Afecto J también el problema zoo-sanitario del acaro varroa a partir de 1999, aumentando los costos de producción de la empresa. De los costos de producción el 43.70 % correspondió a insumos, el27.7% a servicios, el7.37% a mano de obra y un 22.8% a las amortizaciones; La reproducción de miel que se obtuvo fue de 438 Kg. en el ciclo apícola en tres cosechas, 48 Kg. en agosto, 112 Kg. en Noviembre y 278 Kg. en abril del2000, lo que refleja 109. 7 Kg. de miel/ apiario/ ciclo y 5.2 Kg. de miel/ colmena / apiario / ciclo. De los ingresos que se obtuvieron en este ciclo el 71. 67 % corresponde a la venta de cámaras de crías y el 28.33 % a la venta de miel. El margen bruto 1 apiario 1 ciclo fue de C$ 1429.75, el margen bruto 1 colmena de C$ 68.9 y el margen bruto / día/ hombre fue de C$ 62.84, lo que muestra parámetros económicos deficientes para mantener las operaciones en la explotación y el margen neto de C$ -6 339 .38.

Comparación de índices productivos y reproductivos de monta natural e inseminación artificial con semen congelado en cerdos

El presente trabajo de tesis se realizó en la granja experimental porcina MAGFOR-Misión China de la república de Taiwán, ubicada en Cofradía. El estudio consistió en la evaluación de los parámetros reproductivos en grupos de cerdas obtenidos por inseminación artificial y grupos obtenidos a través de la monta natural, también se aborda el tema de la consanguinidad y sus consecuencias como un factor negativo en la fijación de caracteres indeseables, esto sucede en las poblaciones en las que existe una alta homocigosis debido al origen común del material genético (padres emparentados). Las variables evaluadas en el presente trabajo fueron: tamaño de la camada al nacimiento, peso promedio de los lechones al nacimiento, peso promedio de los lechones al destete e intervalo parto parto. para el análisis estadístico se elaboraron tablas de contingencias por cada una de las variables con base en los promedios. Para la variable tamaño de la camada al nacimiento se obtuvo para el tratamiento inseminación artificial un promedio de 9.16 lechones y para la monta natural un promedio de 9.89 lechones al contrastar las medias de los dos tratamientos se obtuvo un valor de t de 0.88 que comparado con el valor tabulado al 5% resulto no significativo al observar el comportamiento de las diferentes razas ,la yorkshire obtuvo los mayores promedios en inseminación el caso especifico de esta habían muy pocos ejemplares 6 . Se trabajo en condiciones normales de producción lo cual pudo influir en estos resultados debido al tamaiio de la muestra en esta raza. Los resultados para la variable peso promedio de los lechones al nacimiento, arrojaron un promedio de 1.76 Kg. para las camadas obtenidas por inseminación artificial y 1.67kg para las obtenidas por el método de monta natural en las observaciones de los promedios por razas, se obtuvo el mayor peso a favor de la raza Landrace con 1.99 Kg. seguido de la raza duroc con 1.85 Kg. en el tratamiento de inseminación artificial, y para la monta natural el menor peso lo obtuvo la raza duroc con 1.44 Kg. y elmayor peso fue también la raza Landrace. la raza Yorkshire mostró un comportamiento similar tanto en inseminacion artificial, como en monta natural. Para la variable peso promedio de los lechones al destete, se obtuvo un peso promedio de 7.39 Kg. para los lechones obtenidos por el método de inseminacion artificial y un peso promedio de 6.71 Kg. en el caso de lechones obtenidos por monta natural al evaluar las razas, la raza Landrace obtuvo el mayor peso al destete con 8.01 Kg. como era de esperar al obtener los mayores promedios en peso al nacimiento esto fue para las camadas obtenidas por inseminacion artificial. en el caso. de los lechones obtenidos mediante la monta natural el mayor peso correspondió a la raza Hampshire pudiendo haber influido el numero de lechones, ya que esta fue la que presento el menor numero la raza Yorkshire tuvo en este caso un comportamiento similar en los dos tratamientos. Para la variable intervalo parto-parto, en el caso de las cerdas servidas por el método de inseminacion artificial presentaron un IPP de 5.52 meses o sea 167 días y las cerdas servidas por monta natural obtuvieron un IPP de5.01 meses o 152 días. En la prueba de hipótesis tanto como el contraste de varianza, los resultados fueron significativos y una diferencia de 15 días vacíos en una hembra eleva los costos de producción de una manera considerable por esta razón un IPP como el de la inseminación artificial solo se justifica en la granja experimental porcina en un numero especifico de cerdas elite y como apoyo al mejoramiento genético del hato porcino de esta así como del hato nacional.

Terapia homeopatica con Nosode en el control de mastitis bovina en Finca Santa Ana, municipio de Paiwas de la RAAS, Nicaragua

El presente trabajo se realizó en la finca Santa Ana Ana ubicada en las coordenadas de latitud Norte de 12º 47’longitud Oeste de 85º 07’y una altitud aproximada de 145.88 msnm en el Municipio de Paiwas, Departamento de la RAAS. Con el objetivo de evaluar un tratamiento homeopático (nosode de leche–mastitis-CH 7)contra mastitis bovina la cual es normalmente atendida por antibióticos, durante el trabajo de investigación se aplicaron tres tratamientos: I aplicación pliegue ano caudal, II aplicación sublingual y III tratamiento testigo con masticilina. Se seleccionaron 30 vacas con mastitis dividiéndolos en tres grupos de 10 cada uno donde las hembras se encontraban entre dos y tres meses de lactancia. Se encontró diferencia altamente significativa (P<0.01) para las variables fecha y vacas, y significativa (P<0.05), para las variables tratamiento y cuartos afectados. En los tratamientos el que controló mejor las afecciones en menos tiempo fue el químico, seguido del nosode de aplicación ano caudal, y el de menor control el nosode de aplicación sublingual, aunque este no difirió significativamente del nosode de aplicación ano caudal El cuarto que presentó la mayor afectación fue el cuarto trasero derecho (64%) seguido del cuarto delantero derecho (61%), el delantero izquierdo presentó la menor afectación con 49%, y el trasero izquierdo un porcentaje de afectación intermedia de 53%.

Computational study of viscous effects on lobed mixer flow features and performance

This article describes a computational study of viscous effects on lobed mixer flowfields. The computations, which were carried out using a compressible, three-dimensional, unstructured-mesh Navier-Stokes solver, were aimed at assessing the impacts on mixer performance of inlet boundary-layer thickness and boundary-layer separation within the lobe. The geometries analyzed represent a class of lobed mixer configurations used in turbofan engines. Parameters investigated included lobe penetration angles from 22 to 45 deg, stream-to-stream velocity ratios from 0.5 to 1.0, and two inlet boundary-layer displacement thicknesses. The results show quantitatively the increasing influence of viscous effects as lobe penetration angle is increased. It is shown that the simple estimate of shed circulation given by Skebe et al. (Experimental Investigation of Three-Dimensional Forced Mixer Lobe Flow Field, AIAA Paper 88-3785, July, 1988) can be extended even to situations in which the flow is separated, provided an effective mixer exit angle and height are defined. An examination of different loss sources is also carried out to illustrate the relative contributions of mixing loss and of boundary-layer viscous effects in cases of practical interest.