Load sharing and power quality enhanced operation of a distributed microgrid

This paper describes control methods for proper load sharing between parallel converters connected in a microgrid and supplied by distributed generators (DGs). It is assumed that the microgrid spans a large area and it supplies loads in both in grid connected and islanded modes. A control strategy is proposed to improve power quality and proper load sharing in both islanded and grid connected modes. It is assumed that each of the DGs has a local load connected to it which can be unbalanced and/or nonlinear. The DGs compensate the effects of unbalance and nonlinearity of the local loads. Common loads are also connected to the microgrid, which are supplied by the utility grid under normal conditions. However during islanding, each of the DGs supplies its local load and shares the common load through droop characteristics. Both impedance and motor loads are considered to verify the system response. The efficacy of the controller has been validated through simulation for various operating conditions using PSCAD. It has been found through simulation that the total Harmonic Distortion (THD) of the of the microgrid voltage is about 10% and the negative and zero sequence component are around 20% of the positive sequence component before compensation. After compensation, the THD remain below 0.5%, whereas, negative and zero sequence components of the voltages remain below 0.02% of the positive sequence component.

The impact of delayed blood centrifuging, choice of collection tube, and type of assay on 25-hydroxyvitamin D concentrations

Studies have examined the associations between cancers and circulating 25-hydroxyvitamin D [25(OH)D], but little is known about the impact of different laboratory practices on 25(OH)D concentrations. We examined the potential impact of delayed blood centrifuging, choice of collection tube, and type of assay on 25(OH)D concentrations. Blood samples from 20 healthy volunteers underwent alternative laboratory procedures: four centrifuging times (2, 24, 72, and 96 h after blood draw); three types of collection tubes (red top serum tube, two different plasma anticoagulant tubes containing heparin or EDTA); and two types of assays (DiaSorin radioimmunoassay [RIA] and chemiluminescence immunoassay [CLIA/LIAISON®]). Log-transformed 25(OH)D concentrations were analyzed using the generalized estimating equations (GEE) linear regression models. We found no difference in 25(OH)D concentrations by centrifuging times or type of assay. There was some indication of a difference in 25(OH)D concentrations by tube type in CLIA/LIAISON®-assayed samples, with concentrations in heparinized plasma (geometric mean, 16.1 ng ml−1) higher than those in serum (geometric mean, 15.3 ng ml−1) (p = 0.01), but the difference was significant only after substantial centrifuging delays (96 h). Our study suggests no necessity for requiring immediate processing of blood samples after collection or for the choice of a tube type or assay.

Indoor environment sustainability of residential industrial housing in Malaysia

The importance of sustainable development has been internationally recognized and the principles have been widely used as an impetus for promoting housing sustainability. In the situation of mixed-use urban development in close proximity to heavy industrial areas in Malaysia, rising incomes are developing hand in hand with higher expectations for better and more sustainable housing designs. Negative environmental impacts due current deficiency in Malaysia’s approach to the implementation of sustainable development principles can be seen in this case study of the Pasir Gudang Industrial Area in Malaysia. This study aimed to highlight the level of residents’ satisfaction with living near the industrial area, and to relate their awareness of the relevance of sustainable principles with indoor environmental conditions, which found that the residents’ has limited understanding of the environmental problems in their indoor living conditions and in their neighborhoods. This study has suggested that proactive and integrated involvement by housing authorities from all levels of government in Malaysia should be encouraged in order to rationalise the approaches to develop better planning solutions for such mixed-used urban developments. This initiative should then encourage housing vendors to provide innovative ‘smart’ technological changes to their projects and so, to achieve a new direction in sustainable housing development.

Thermogravimetric analysis and hot stage Raman spectroscopy of cubic indium hydroxide

The transition of cubic indium hydroxide to cubic indium oxide has been studied by thermogravimetric analysis complimented with hot stage Raman spectroscopy. Thermal analysis shows the transition of In(OH)3 to In2O3 occurs at 219°C. The structure and morphology of In(OH)3 synthesised using a soft chemical route at low temperatures was confirmed by X-ray diffraction and scanning electron microscopy. A topotactical relationship exists between the micro/nano-cubes of In(OH)3 and In2O3. The Raman spectrum of In(OH)3 is characterised by an intense sharp band at 309 cm-1 attributed to ν1 In-O symmetric stretching mode, bands at 1137 and 1155 cm-1 attributed to In-OH δ deformation modes, bands at 3083, 3215, 3123 and 3262 cm-1 assigned to the OH stretching vibrations. Upon thermal treatment of In(OH)3 new Raman bands are observed at 125, 295, 488 and 615 cm-1 attributed to In2O3. Changes in the structure of In(OH)3 with thermal treatment is readily followed by hot stage Raman spectroscopy.

Venture creation and resource processes : using Bricolage sustainability ventures

Principal Topic: Resource decisions are critical to the venture creation process, which has important subsequent impacts on venture creation and performance (Boeker, 1989). Most entrepreneurs however, suffer substantial resource constraints in venture creation and during venture growth (Shepherd et al., 2000). Little is known about how high potential, sustainability ventures (the ventures of interest in this research), despite resource constraints, achieve continued venture persistence and venture success. One promising theory that explicitly links to resource constraints is a concept developed by Levi Strauss (1967) termed bricolage. Bricolage aligns with notions of resourcefulness: using what's on hand, through making do, and recombining resources for new or novel purposes (Baker & Nelson 2005). To the best of our knowledge, previous studies have not systematically investigated internal and external constraints, their combinations, and subsequent bricolage patterns. The majority of bricolage literature focuses on external environmental constraints (e.g. Wieck 1989; Baker & Nelson 2005), thereby paying less attention to in evaluating internal constraints (e.g. skills and capabilities) or constraint combinations. In this paper we focus on ventures that typically face resource-poor environments. High potential, nascent and young sustainability ventures are often created and developed with resource constraints and in some cases, have greater resource requirements owing to higher levels of technical sophistication of their products (Rothaermel & Deeds 2006). These ventures usually have high aspirations and potential for growth who ''seeks to meet the needs and aspirations without compromising the ability to meet those of the future'' (Brundtland Commission 1983). High potential ventures are increasingly attributed with a central role in the development of innovation, and employment in developed economies (Acs 2008). Further, increasing awareness of environmental and sustainability issues has fostered demand for business processes that reduce detrimental environmental impacts of global development (Dean & McMullen 2007) and more environmentally sensitive products and services: representing an opportunity for the development of ventures that seek to satisfy this demand through entrepreneurial action. These ventures may choose to ''make do'' with existing resources in developing resource combinations that produce the least impact on the environment. The continuous conflict between the greater requirements for resources and limited resource availability in high potential sustainable ventures, with the added complexity of balancing this with an uncompromising focus on using ''what's on hand'' to lessen environment impacts may make bricolage behaviours critical for these ventures. Research into bricolage behaviour is however, the exception rather than the rule (Cunha 2005). More research is therefore needed to further develop and extend this emerging concept, especially in the context of sustainability ventures who are committed to personal and social goals of resourcefulness. To date, however, bricolage has not been studied specifically among high potential sustainable ventures. This research seeks to develop an in depth understanding of the impact of internal and external constraints and their combinations on the mechanisms employed in bricolage behaviours in differing dynamic environments. The following research question was developed to investigate this: How do internal, external resource constraints (or their combinations) impact bricolage resource decisions in high potential sustainability ventures? ---------- Methodology/Key Propositions: 6 case studies will be developed utilizing survey data from the Comprehensive Australian Study of Entrepreneurial Emergence (CAUSEE) large-scale longitudinal study of new venture start-ups in Australia. Prior to commencing case studies, 6 scoping interviews were conducted with key stakeholders including industry members, established businesses and government to ensure practical relevance in case development. The venture is considered the unit of analysis with the key informant being the entrepreneur and other management team members where appropriate. Triangulation techniques are used in this research including semi-structured interviews, survey data, onsite visits and secondary documentation website analysis, resumes, and business plans. These 6 sustainability ventures have been selected based on different environmental dynamism conditions including a traditionally mature market (building industry) and a more dynamic, evolving industry (renewable energy/solar ventures). In evaluating multidisciplinary literature, we expect the following external constraints are critical including: technology constraints (seen through lock-in of incumbents existing technology), institutional regulation and standards, access to markets, knowledge and training to nascent and young venture bricolage processes. The case studies will investigate internal constraints including resource fungability, resource combination capabilities, translating complex science/engineering knowledge into salient, valuable market propositions, i.e. appropriate market outcomes, and leveraging relationships may further influence bricolage decisions. ---------- Results and Implications: Intended ventures have been identified within the CAUSEE sample and have agreed to participate and secondary data collection for triangulation purposes has already commenced. Data collection of the case studies commenced 27th of May 2009. Analysis is expected to be completed finalised by 25th September 2009. This paper will report on the pattern of resource constraints and its impact on bricolage behaviours: its subsequent impact on resource deployment within venture creation and venture growth. As such, this research extends the theory of bricolage through the systematic analysis of constraints on resource management processes in sustainability ventures. For practice, this research may assist in providing a better understanding of the resource requirements and processes needed for continued venture persistence and growth in sustainability ventures. In these times of economic uncertainty, a better understanding of the influence on constraints and bricolage: the interplay of behaviours, processes and outcomes may enable greater venture continuance and success.

Election campaigns, and television news coverage : the case of the 2001 Australian election

This paper examines the patterns of television news coverage of the political parties, their leaders and the issues they raised during the 2001 Australian federal election campaign. By focusing on some issues, parties and leaders, television has long been argued to constrain voters' evaluations. We find that television news coverage in the 2001 Australian election campaign focused primarily on international issues, especially terrorism and asylum seekers, and on the two major parties - virtually to the exclusion of coverage of the minor parties and their leaders. Within the major party 'two-horse race', television gave substantially more coverage to the leaders than to the parties themselves, thereby sustaining what some have called a 'presidential'-style political contest. John Howard emerged as the winner in the leaders' stakes, garnering more coverage than Labor's Kim Beazley.

Social Participation of Community Dwelling Stroke Survivors [Published Abstract: From the Quality of Care and Outcomes Research in Cardiovascular Disease and Stroke Conference 2009]

Disability following a stroke can impose various restrictions on patients’ attempts at participating in life roles. The measurement of social participation, for instance, is important in estimating recovery and assessing quality of care at the community level. Thus, the identification of factors influencing social participation is essential in developing effective measures for promoting the reintegration of stroke survivors into the community. Data were collected from 188 stroke survivors (mean age 71.7 years) 12 months after discharge from a stroke rehabilitation hospital. Of these survivors, 128 (61 %) had suffered a first ever stroke, and 81 (43 %) had a right hemisphere lesion. Most (n = 156, 83 %) were living in their own home, though 32 (17 %) were living in residential care facilities. Path analysis was used to test a hypothesized model of participation restriction which included the direct and indirect effects between social, psychological and physical outcomes and demographic variables. Participation restriction was the dependent variable. Exogenous independent variables were age, functional ability, living arrangement and gender. Endogenous independent variables were depressive symptoms, state self-esteem and social support satisfaction. The path coefficients showed functional ability having the largest direct effect on participation restriction. The results also showed that more depressive symptoms, low state self-esteem, female gender, older age and living in a residential care facility had a direct effect on participation restriction. The explanatory variables accounted for 71% of the variance in explaining participation restriction. Prediction models have empirical and practical applications such as suggesting important factors to be considered in promoting stroke recovery. The findings suggest that interventions offered over the course of rehabilitation should be aimed at improving functional ability and promoting psychological aspects of recovery. These are likely to enhance stroke survivors resume or maximize their social participation so that they may fulfill productive and positive life roles.

Solving graphics tasks : gender differences in middle-school students

The capacity to solve tasks that contain high concentrations of visual-spatial information, including graphs, maps and diagrams, is becoming increasingly important in educational contexts as well as everyday life. This research examined gender differences in the performance of students solving graphics tasks from the Graphical Languages in Mathematics (GLIM) instrument that included number lines, graphs, maps and diagrams. The participants were 317 Australian students (169 males and 148 females) aged 9 to 12 years. Boys outperformed girls on graphical languages that required the interpretation of information represented on an axis and graphical languages that required movement between two- and three-dimensional representations (generally Map language).

Safety-restraint use rate as function of law enforcement and other factors : preliminary analysis

Persistent use of safety restraints prevents deaths and reduces the severity and number of injuries resulting from motor vehicle crashes. However, safety-restraint use rates in the United States have been below those of other nations with safety-restraint enforcement laws. With a better understanding of the relationship between safety-restraint law enforcement and safety-restraint use, programs can be implemented to decrease the number of deaths and injuries resulting from motor vehicle crashes. Does safety-restraint use increase as enforcement increases? Do motorists increase their safety-restraint use in response to the general presence of law enforcement or to targeted law enforcement efforts? Does a relationship between enforcement and restraint use exist at the countywide level? A logistic regression model was estimated by using county-level safety-restraint use data and traffic citation statistics collected in 13 counties within the state of Florida in 1997. The model results suggest that safety-restraint use is positively correlated with enforcement intensity, is negatively correlated with safety-restraint enforcement coverage (in lanemiles of enforcement coverage), and is greater in urban than rural areas. The quantification of these relationships may assist Florida and other law enforcement agencies in raising safety-restraint use rates by allocating limited funds more efficiently either by allocating additional time for enforcement activities of the existing force or by increasing enforcement staff. In addition, the research supports a commonsense notion that enforcement activities do result in behavioral response.

Model interoperability in building information modelling

The exchange of design models in the design and construction industry is evolving away from 2-dimensional computer-aided design (CAD) and paper towards semantically-rich 3-dimensional digital models. This approach, known as Building Information Modelling (BIM), is anticipated to become the primary means of information exchange between the various parties involved in construction projects. From a technical perspective, the domain represents an interesting study in model-based interoperability, since the models are large and complex, and the industry is one in which collaboration is a vital part of business. In this paper, we present our experiences with issues of model-based interoperability in exchanging building information models between various tools, and in implementing tools which consume BIM models, particularly using the industry standard IFC data modelling format. We report on the successes and challenges in these endeavours, as the industry endeavours to move further towards fully digitised information exchange.

Petri net modeling of spatial and temporal constraints in track allocation problem at railway stations

The track allocation problem (TAP) at a multi-track, multi-platform mainline railway station is defined by the station track layout and service timetable, which implies combinations of spatial and temporal conflicts. Feasible solutions are available from either traditional planning or advanced intelligent searching methods and their evaluations with respect to operational requirements are essential for the operators. To facilitate thorough analysis, a timed Coloured Petri Nets (CPN) model is presented here to encapsulate the inter-relationships of the spatial and temporal constraints in the TAP.

Vitamin D intake needed to maintain target serum 25-Hydroxyvitamin D concentrations in participants with low sun exposure and dark skin pigmentation is substantially higher than current recommendations

Cutaneous cholecalciferol synthesis has not been considered in making recommendations for vitamin D intake. Our objective was to model the effects of sun exposure, vitamin D intake, and skin reflectance (pigmentation) on serum 25-hydroxyvitamin D (25[OH]D) in young adults with a wide range of skin reflectance and sun exposure. Four cohorts of participants (n = 72 total) were studied for 7-8 wk in the fall, winter, spring, and summer in Davis, CA [38.5° N, 121.7° W, Elev. 49 ft (15 m)]. Skin reflectance was measured using a spectrophotometer, vitamin D intake using food records, and sun exposure using polysulfone dosimeter badges. A multiple regression model (R^sup 2^ = 0.55; P < 0.0001) was developed and used to predict the serum 25(OH)D concentration for participants with low [median for African ancestry (AA)] and high [median for European ancestry (EA)] skin reflectance and with low [20th percentile, ~20 min/d, ~18% body surface area (BSA) exposed] and high (80th percentile, ~90 min/d, ~35% BSA exposed) sun exposure, assuming an intake of 200 IU/d (5 ug/d). Predicted serum 25(OH)D concentrations for AA individuals with low and high sun exposure in the winter were 24 and 42 nmol/L and in the summer were 40 and 60 nmol/L. Corresponding values for EA individuals were 35 and 60 nmol/L in the winter and in the summer were 58 and 85 nmol/L. To achieve 25(OH)D ≥75 nmol/L, we estimate that EA individuals with high sun exposure need 1300 IU/d vitamin D intake in the winter and AA individuals with low sun exposure need 2100-3100 IU/d year-round.