Thermal decomposition and combustion of ammine: AP pellets

Thermal decomposition and combustion of lithium perchlorate ammine:ammonium perchlorate (LPA:AP) and magnesium perchlorate ammine:ammonium perchlorate (MPA:AP) pellets have been studied using DTA, TG, and strand burner techniques. The DTA results of the ammine:AP pellets show that the addition of ammines lowers the ignition temperature of AP. However, isothermal TG of the ammine:AP pellets show that in the case of LPA:AP pellets the extent of decomposition increases with the increase in the concentration of LPA; whereas in the case of MPA:AP pellets the extent of decomposition decreases with the increase in the concentration of MPA. Similarly, LPA:AP pellets show higher burning rates compared to AP pellets. On the other hand, MPA:AP pellets show lower burning rates compared to AP pellets. Increasing the concentration of MPA in MPA:AP pellets completely suppresses the combustion. These results are explained on the basis of the thermal characteristics of the additives and their decomposition products.

Thermal analysis of hydrazinium metal sulphates and their hydrazinates

Thermal analysis of hydrazinium metal sulphates, (N2H5)2 M(SO4)-I, and their hydrazinates, (N2H5)2−M(SO4)23N2H4−II, whereM=Fe, Co and Ni have been investigated using thermogravimetry and differential thermal analysis. Type II compounds on heating decompose through an intermediate I and metal suphlate to the respective metal oxides.

Preparation and thermal stability of trioxalatocobaltates of bivalent metals KM2+ [Co(C2O4)3]·xH2O

Trioxalatocobaltates of bivalent metals KM2+[Co(C2O4)3]·x H2O, with M2+ = Ba, Sr, Ca and Pb, have been prepared, characterized and their thermal behaviour studied. The compounds decompose to yield potassium carbonate, bivalent metal carbonate or oxide and cobalt oxide as final products. The formation of the final products of decomposition is influenced by the surrounding atmosphere. Bivalent metal cobaltites of the types KM2+CoO3 and M2+CoO3—x are not identified among the final products of decomposition. The study brings out the importance of the decomposition mode of the precursor in producing the desired end products.

Thermal activation parameters for low temperature deformation of alpha-hafnium

Abstract is not available.

Nomenclatural corrections to Australian species of Cricotopus (Wulp) (Diptera; Chironomidae)

Our attention has been drawn to lapsi and errors in a recent publication in this journal concerning Cricotopus Wulp (Diptera: Chironomidae) (Drayson et al., 2015).

Restoration of symmetry by radiative corrections

It is shown using an explicit model that radiative corrections can restore the symmetry of a system which may appear to be broken at the classical level. This is the reverse of the phenomenon demonstrated by Coleman and Weinberg. Our model is different from theirs, but the techniques are the same. The calculations are done up to the two-loop level and it is shown that the two-loop contribution is much smaller than the one-loop contribution, indicating good convergence of the loop expansion.

Combustion and Thermal Decomposition of Ammonium Perchlorate-Aluminium Composite Pellets: Mechanism for Aluminium Participation

Thermal behaviour of ammonium perchlorate-aluminium composites is studied using differential thermal analysis, thermogravimetry and differential scanning calorimetry. Electrical resistivity studies throw light on the mechanism of ammonium perchlorate decomposition at different aluminium contents. The differences observed in burning behaviour by earlier authors is explained in terms of porosity and thermal conductivity of the composite.

Ultrasonic velocities and thermal expansion coefficients of amorphous Se80Te20 and Se90Te10 alloys near glass transitions

Precise measurements of the ultrasonic velocities and thermal expansivities of amorphous Se80Te20 and Se90Te10 alloys are reported near the glass transition. The samples are produced by liquid quenching. The longitudinal and transverse velocities are measured at 10 MHz frequency using the McSkimin pulse superposition technique. The thermal expansivities,agr, are measured using a three-terminal capacitance bridge. Theagr-values show a sharp maximum near the glass transition temperature,T g. The ultrasonic velocities also show a large temperature derivative, dV/dT nearT g. The data are discussed in terms of existing theories of the glass transition. The continuous change inagr shows that the glass transition is not a first-order transition, as suggested by some theories. The samples are found to be deformed by small loads nearT g. The ultrasonic velocities and dV/dT have contributions arising from this deformation.

Thermal reactivity of metal oxalate hydrazinates

Metal oxalate hydrazinates MC2O4·2 N2H4 where M=Mg, Mn, Fe, Co, Ni, Cu, Zn and Cd have been prepared and characterised by chemical analysis and infrared spectra. Thermal reactivity and decomposition of these oxalato complexes have been studied using thermogravimetry and differential thermal analysis. Hydrazinates of Mn, Fe, Co, Ni and Cu oxalates exhibit autocatalytic decomposition behaviour whereas the others do not. This phenomenon can be attributed to the presence of a bridged hydrazine as well as the thermal stability of the anhydrous metal oxalates.

Study of switching characteristics and thermal noise in ferroelectric crystals both in the pure and radiation damaged state

The phase transition in gamma-irradiated triglycine sulphate (TGS) has been investigated by using a method based on the measurement of thermal noise. The results of a study of the polarization switching characteristics of gamma irradiated TGS and sodium nitrite (NaNO2) have also been presented. The effect of irradiation on the phase transition and the switching processes has been discussed.

Measurement of sensitivities for the thermal recording of laser beams

A simple technique for determining the energy sensitivities for the thermographic recording of laser beams is described. The principle behind this technique is that, if a laser beam with a known spatial distribution such as a Gaussian profile is used for imaging, the radius of the thermal image formed depends uniquely on the intensity of the impinging beam. Thus by measuring the radii of the images produced for different incident beam intensities the minimum intensity necessary (that is, the threshold) for thermographic imaging is found. The diameter of the laser beam can also be found from this measurement. A simple analysis based on the temperature distribution in the laser heated material shows that there is an inverse square root dependence on pulse duration or period of exposure for the energy fluence of the laser beam required, both for the threshold and the subsequent increase in the size of the recording. It has also been shown that except for low intensity, long duration exposure on very low conductivity materials, heat losses are not very significant.

Preparation, Characterisation and Thermal Properties of Hydrazinium Magnesium Sulfate

Hydrazinium magnesium sulfate, (N2H5)2Mg(SO4)2, has been prepared by dissolving magnesium powder in a solution of ammonium sulfate in hydrazine hydrate, by the reaction of ammonium magnesium sulfate with hydrazine hydrate, and by the cocrystallisation of dihydrazinium sulfate and magnesium sulfate. The product has been characterized by chemical analysis and infrared spectra. Thermal analysis of (N2H5)2Mg(SO4)2 by TG and DTA show exothermic decomposition at 302°C giving Mg(N2H4)SO4 as an intermediate and an endother-mic decomposition at 504°C producing MgSO4.

Thermal decomposition of alkali metal perchlorates

The effect of past mechanical history on the subsequent thermal decomposition kinetics of sodium, potassium, rubidium and caesium perchlorates, has been investigated. At low temperatures the decomposition of all these salts is significantly sensitized by pre-compression. At high temperatures, however, prior compression results in a lowered decomposition rate in the case of potassium, rubidium and caesium perchlorates and in an increase in the thermal reactivity of sodium perchlorate. The high temperature behaviour is shown to be an indirect consequence of the low temperature behaviour. The difference in behaviour between sodium perchlorate and the other alkali metal perchlorates is explained on the basis of the stability of the respective chlorates, formed during the low temperature decomposition. This is substantiated by experiments which show that the addition of sodium chlorate to sodium perchlorate brings about a sensitization while potassium perchlorate admixed with potassium chlorate results in a desensitization at high temperatures.