ORGANOSILICON BIOTECHNOLOGY: A BIO-INSPIRED APPROACH TO THE HYDROLYSIS OF ALKOXYSILANES and THE LIPASE-CATALYZED SYNTHESIS OF SILOXANE-CONTAINING POLYESTERS AND POLYAMIDES

The first part of this thesis studied the capacity of amino acids and enzymes to catalyze the hydrolysis and condensation of tetraethoxysilane and phenyltrimethoxysilane. Selected amino acids were shown to accelerate the hydrolysis and condensation of tetraethoxysilane under ambient temperature, pressure and at neutral pH (pH 7±0.02). The nature of the side chain of the amino acid was important in promoting hydrolysis and condensation. Several proteases were shown to have a capacity to hydrolyze tri- and tet-ra- alkoxysilanes under the same mild reaction conditions. The second part of this thesis employed an immobilized Candida antarctica lipase B (Novozym-435, N435) to produce siloxane-containing polyesters, polyamides, and polyester amides under solvent-free conditions. Enzymatic activity was shown to be temperature dependent, increasing until enzyme denaturation became the dominant pro-cess, which typically occurred between 120-130ᵒC. The residual activity of N435 was, on average, greater than 90%, when used in the synthesis of disiloxane-containing polyesters, regardless of the polymerization temperature except at the very highest temperatures, 140-150ᵒC. A study of the thermal tolerance of N435 determined that, over ten reaction cycles, there was a decrease in the initial rate of polymerization with each consecutive use of the catalyst. No change in the degree of monomer conversion after a 24 hour reaction cycle was found.

The Synthesis of Imidazole Fatty Acid Conjugates as Inhibitors of Apoptosis

Ionizing radiation is known to initiate apoptosis in mammalian cells by causing the transformation of cytochrome c into a peroxidase, which results in the specific peroxidation of the mitochondrial phospholipid cardiolipin. Here we report the design and synthesis of 8 imidazole fatty acid derivatives that bind to the cyt c:CL complex and inhibit the peroxidase activity required for the initiation of apoptosis. We postulate that imidazole acts as a sixth ligand to the haem iron and stops the interaction with H2O2. Two mitochondrially directed analogues (3-hydroxypropyl)triphenylphosphonium esters) of 12-imidazole-stearic acid and 12-imidazole-oleic acid not only were demonstrated to be peroxidase inhibitors in vitro, but were also extraordinarily effective in protecting mice from lethal doses (9 Gy) of ionization radiation. We studied the structure activity relationship to a group of triphenyl phosphonium derivatives containing imidazole at different positions on the fatty acid chain, and observed that the C8-imidazole stearate analogue had marginally better activity than the others. But overall, the structure activity result were remarkable “flat” with all compounds prepared having rather similar inhibitory strength. We also synthesized carnitine mono and di-esters of 12-imidazole fatty acids but full biological data is not yet available for these compounds.

Supramolecular polymers azo-containing : photo-responsive block copolymer elastomers and homopolymers

Beaucoup d'efforts dans le domaine des matériaux polymères sont déployés pour développer de nouveaux matériaux fonctionnels pour des applications spécifiques, souvent très sophistiquées, en employant des méthodes simplifiées de synthèse et de préparation. Cette thèse porte sur les polymères photosensibles – i.e. des matériaux fonctionnels qui répondent de diverses manières à la lumière – qui sont préparés à l'aide de la chimie supramoléculaire – i.e. une méthode de préparation qui repose sur l'auto-assemblage spontané de motifs moléculaires plus simples via des interactions non covalentes pour former le matériau final désiré. Deux types de matériaux photosensibles ont été ciblés, à savoir les élastomères thermoplastiques à base de copolymères à blocs (TPE) et les complexes d'homopolymères photosensibles. Les TPEs sont des matériaux bien connus, et même commercialisés, qui sont généralement composés d’un copolymère tribloc, avec un bloc central très flexible et des blocs terminaux rigides qui présentent une séparation de phase menant à des domaines durs isolés, composés des blocs terminaux rigides, dans une matrice molle formée du bloc central flexible, et ils ont l'avantage d'être recyclable. Pour la première fois, au meilleur de notre connaissance, nous avons préparé ces matériaux avec des propriétés photosensibles, basé sur la complexation supramoléculaire entre un copolymère tribloc simple parent et une petite molécule possédant une fonctionnalité photosensible via un groupe azobenzène. Plus précisément, il s’agit de la complexation ionique entre la forme quaternisée d'un copolymère à blocs, le poly(méthacrylate de diméthylaminoéthyle)-poly(acrylate de n-butyle)-poly(méthacrylate de diméthylaminoéthyle) (PDM-PnBA-PDM), synthétisé par polymérisation radicalaire par transfert d’atomes (ATRP), et l'orange de méthyle (MO), un composé azo disponible commercialement comportant un groupement SO3 -. Le PnBA possède une température de transition vitreuse en dessous de la température ambiante (-46 °C) et les blocs terminaux de PDM complexés avec le MO ont une température de transition vitreuse élevée (140-180 °C, en fonction de la masse molaire). Des tests simples d'élasticité montrent que les copolymères à blocs complexés avec des fractions massiques allant de 20 à 30% présentent un caractère élastomère. Des mesures d’AFM et de TEM (microscopie à force atomique et électronique à ii transmission) de films préparés à l’aide de la méthode de la tournette, montrent une corrélation entre le caractère élastomère et les morphologies où les blocs rigides forment une phase minoritaire dispersée (domaines sphériques ou cylindriques courts). Une phase dure continue (morphologie inversée) est observée pour une fraction massique en blocs rigides d'environ 37%, ce qui est beaucoup plus faible que celle observée pour les copolymères à blocs neutres, dû aux interactions ioniques. La réversibilité de la photoisomérisation a été démontrée pour ces matériaux, à la fois en solution et sous forme de film. La synthèse du copolymère à blocs PDM-PnBA-PDM a ensuite été optimisée en utilisant la technique d'échange d'halogène en ATRP, ainsi qu’en apportant d'autres modifications à la recette de polymérisation. Des produits monodisperses ont été obtenus à la fois pour la macroamorceur et le copolymère à blocs. À partir d'un seul copolymère à blocs parent, une série de copolymères à blocs partiellement/complètement quaternisés et complexés ont été préparés. Des tests préliminaires de traction sur les copolymères à blocs complexés avec le MO ont montré que leur élasticité est corrélée avec la fraction massique du bloc dur, qui peut être ajustée par le degré de quaternisation et de complexation. Finalement, une série de complexes d'homopolymères auto-assemblés à partir du PDM et de trois dérivés azobenzènes portant des groupes (OH, COOH et SO3) capables d'interactions directionnelles avec le groupement amino du PDM ont été préparés, où les dérivés azo sont associés avec le PDM, respectivement, via des interactions hydrogène, des liaisons ioniques combinées à une liaison hydrogène à travers un transfert de proton (acidebase), et des interactions purement ioniques. L'influence de la teneur en azo et du type de liaison sur la facilité d’inscription des réseaux de diffraction (SRG) a été étudiée. L’efficacité de diffraction des SRGs et la profondeur des réseaux inscrits à partir de films préparés à la méthode de la tournette montrent que la liaison ionique et une teneur élevée en azo conduit à une formation plus efficace des SRGs.

Probiotic Effects of Lactic Acid Bacteria Against Vibrio Alginolyticus in Penaeus (Fenneropenaeus) Indicus (H. Milne Edwards)

Cell free extracts of four strains of Lactic acid bacteria (LAB) viz. Lactobacillus. acidophilus, Streptococcus.cremoris, Lactobacillus bulgaricus –56 and Lactobacillus bulgaricus –57 inhibited growth of Vibrio alginolyticus in nutrient broth. The antagonism of LAB to Vibrio alginolyticus was further confirmed by streak plating wherein suppression of growth of Vibrio was obtained. Juveniles of Penaeus indicus (average weight 0.985 ± 0.1 g) on administering orally a moist feed base containing 5 × 106 cells·g of the four LAB probionts for a period of four weeks showed better survival (56 to 72%) when challenged with V. alginolyticus by intra-muscular injection of 0.1 ml containing 3 × 109 cells·ml. Animals maintained on a diet devoid of bacterial biomass exhibited 80% mortality. No external or internal pathological changes were observed in shrimp fed with the LAB incorporated diets. Results showed inhibition of V. alginolyticus by LAB and stimulation of the non-specific immune response resulting in resistance to disease in the shrimp fed on LAB incorporated diets.

New mono- and dinuclear ruthenium complexes containing the 3,5-bis(2-pyridyl)pyrazole ligand. Synthesis, characterization and applications

Se han sintetizado dos nuevos complejos mononucleares de Ru, con formula [RuCl2(Hbpp)(dmso)2], a partir de la reacción entre [RuCl2(dmso)4] y Hbpp (3,5-bis(2-piridil)pirazola). El hecho que sólo tres de los seis posibles estereoisómeros se obtengan a partir de esta reacción, se ha racionalizado en base a factores estructurales y electrónicos. Estos complejos se han caracterizado de forma estructural, espectroscópica y electroquímica. En acetonitrilo en medio básico, el isómero trans,cis-[RuCl2(Hbpp)(dmso)2] da lugar a procesos de isomerización de enlace de un ligando dmso cuando el Ru(II) se oxida a Ru(III). Las constantes termodinámicas y cinéticas para el proceso se han determinado por voltametria cíclica. La irradiación de trans,cis-[RuCl2(Hbpp)(dmso)2] y cis(out),cis-[RuCl2(Hbpp)(dmso)2] con luz UV o solar da lugar a reacciones de fotosustitución de un ligando dmso por una molécula de acetonitrilo para dar un nuevo compuesto el cual ha sido caracterizado en solución por técnicas espectroscópicas y electroquímicas. Ambos complejos resultan catalizadores útiles en la transferencia de hidrógeno de isopropanol a acetofenona, obteniéndose 1-feniletanol como único producto y un 42.1% de conversión (36.1 ciclos metálicos) a 80ºC con el isómero trans,cis-[RuCl2(Hbpp)(dmso)2], que resulta significativamente más eficaz que el complejo cis(out),cis-[RuCl2(Hbpp)(dmso)2]. La reacción de cis(out),cis-[RuCl2(Hbpp)(dmso)2] con trpy (2,2':6',2"-terpiridina) da lugar a los dos isómeros geométricos del complejo [Ru(Hbpp)(trpy)(Cl)]+, el in y el out. Estos complejos se han aislado y caracterizado por técnicas estructurales, espectroscópicas y electroquímicas. Estos cloro complejos han sido utilizados como precursores para la síntesis de los complejos análogos con ligandos aqua (in,out-[Ru(Hbpp)(trpy)(H2O)]2+) y piridina (in,out-[Ru(Hbpp)(trpy)(py)]2+), los cuales también han sido aislados y caracterizados. Las propiedades ácido-base de los aqua complejos, y del complejo out-py se han estudiado detalladamente por voltametria cíclica y mediante valoraciones espectrofotométricas ácido-base. El tratamiento matemático de los datos así obtenidos nos ha permitido determinar los valores de pKa para los distintos equilibrios de protonación de los complejos en los estados de oxidación II y III. El complejo out-aqua ha demostrado ser un buen catalizador para la oxidación electroquímica del alcohol benzílico, presumiblemente a benzaldehido. La constante de velocidad de segundo orden para el proceso ha sido determinada como 17.1 M-1 s-1, por simulación matemática. El dímero con un puente cloro, [Ru2Cl(bpp)(trpy)2]2+ ha sido preparado por dos rutas sintéticas diferentes. El dímero análogo con un puente acetato se ha obtenido por reacción del cloro dímero con un exceso de acetato sódico. El dímero con dos ligandos aqua [Ru2(bpp)(trpy)2(OH2)2]3+ puede obtenerse por hidrólisis ácida del complejo con un acetato puente o por hidrólisis básica del complejo con un puente cloro. Estos complejos han sido caracterizados por técnicas estructurales, espectroscópicas y electroquímicas. Las soluciones del dímero con dos ligandos aqua en medio ácido resultan inestables a la coordinación de aniones de la solución con el tiempo. Las propiedades ácido-base del dímero con dos aguas coordinadas han sido estudiadas por voltametria cíclica y mediante experimentos de electrólisis a potencial controlado. El pKa para la desprotonación de uno de los ligandos aqua ha sido determinado mediante una valoración espectrofotométrica ácido-base como 6.7. Este valor tan bajo de pKa se atribuye a la formación de la entidad {Ru2O2H3}, favorable termodinámicamente. Los espectros UV-vis para los distintos estados de oxidación del aqua dímero, de RuIIRuII a RuIIIRuIV, han sido obtenidos por oxidación química y electroquímica del complejo. Se han llevado a cabo estudios cinéticos de la oxidación, paso a paso, de RuII,II a RuIV,IV , y se han determinado las constantes de oxidación de segundo orden para los distintos procesos de oxidación. La capacidad del aqua dímero en la oxidación del agua a oxígeno molecular ha sido investigada en solución homogénea utilizando CeIV como oxidante. La evolución de oxígeno se ha demostrado por cromatografia de gases. Se ha obtenido una eficiencia del 73% y 18.6 ciclos catalíticos, cuando 1.83 x 10-6 moles de dímero se han mezclado con un exceso de 100 equivalentes de cerio. El dímero con dos aguas cataliza también la oxidación del agua de forma heterogénea, con el complejo adsorbido sobre una membrana de nafion, aunque la eficiencia es menor. Se ha propuesto un mecanismo intramolecular para la reacción de oxidación del agua. Consiste en la oxidación a 4 electrones del dímero, de RuII,II a RuIV,IV, el cual reacciona con el agua para formar oxígeno y revierte nuevamente al estado de oxidación II,II. Este modelo es consistente con estudios catalíticos de la evolución de oxígeno en función de las concentraciones de cerio y catalizador, llevados a cabo en solución ácida homogénea, que demuestran que la oxidación a 4 electrones del agua se encuentra catalizada por una sola molécula de complejo bajo concentraciones elevadas de cerio. La constante de pseudo-primer-orden para la evolución de oxígeno tiene un valor de 1.4 x 10-2 s-1, que es uno de los valores de constante más elevados obtenidos hasta la fecha. Desafortunadamente, el aqua dímero se desactiva durante el proceso de catálisis dando lugar a una especie naranja, la cual estamos actualmente tratando de caracterizar.

Naturally occurring radioactive material (NORM) from a former phosphoric acid processing plant

In recent years there has been an increasing awareness of the radiological impact of non-nuclear industries that extract and/or process ores and minerals containing naturally occurring radioactive material (NORM). These industrial activities may result in significant radioactive contamination of (by-) products, wastes and plant installations. In this study, scale samples were collected from a decommissioned phosphoric acid processing plant. To determine the nature and concentration of NORM retained in pipe-work and associated process plant, four main areas of the site were investigated: (1) the 'Green Acid Plant', where crude acid was concentrated; (2) the green acid storage tanks; (3) the Purified White Acid (PWA) plant, where inorganic impurities were removed; and (4) the solid waste, disposed of on-site as landfill. The scale samples predominantly comprise the following: fluorides (e.g. ralstonite); calcium sulphate (e.g. gypsum); and an assemblage of mixed fluorides and phosphates (e.g. iron fluoride hydrate, calcium phosphate), respectively. The radioactive inventory is dominated by U-238 and its decay chain products, and significant fractionation along the series occurs. Compared to the feedstock ore, elevated concentrations (<= 8.8 Bq/g) of U-238 Were found to be retained in installations where the process stream was rich in fluorides and phosphates. In addition, enriched levels (<= 11 Bq/g) of Ra-226 were found in association with precipitates of calcium sulphate. Water extraction tests indicate that many of the scales and waste contain significantly soluble materials and readily release radioactivity into solution. (c) 2005 Elsevier Ltd. All rights reserved.

The Wheal Jane wetlands model for bioremediation of acid mine drainage

Acid mine drainage (AMD) is a widespread environmental problem associated with both working and abandoned mining operations. As part of an overall strategy to determine a long-term treatment option for AMD, a pilot passive treatment plant was constructed in 1994 at Wheal Jane Mine in Cornwall, UK. The plant consists of three separate systems, each containing aerobic reed beds, anaerobic cell and rock filters, and represents the largest European experimental facility of its kind. The systems only differ by the type of pretreatment utilised to increase the pH of the influent minewater (pH <4): lime dosed (LD), anoxic limestone drain (ALD) and lime free (LF), which receives no form of pretreatment. Historical data (1994-1997) indicate median Fe reduction between 55% and 92%, sulphate removal in the range of 3-38% and removal of target metals (cadmium, copper and zinc) below detection limits, depending on pretreatment and flow rates through the system. A new model to simulate the processes and dynamics of the wetlands systems is described, as well as the application of the model to experimental data collected at the pilot plant. The model is process based, and utilises reaction kinetic approaches based on experimental microbial techniques rather than an equilibrium approach to metal precipitation. The model is dynamic and utilises numerical integration routines to solve a set of differential equations that describe the behaviour of 20 variables over the 17 pilot plant cells on a daily basis. The model outputs at each cell boundary are evaluated and compared with the measured data, and the model is demonstrated to provide a good representation of the complex behaviour of the wetland system for a wide range of variables. (C) 2004 Elsevier B.V/ All rights reserved.

Bioremediation of acid mine drainage: an introduction to the Wheal Jane wetlands project

Acid mine drainage (AMD) is a widespread environmental problem associated with both working and abandoned mining operations. As part of an overall strategy to determine a long-term treatment option for AMD, a pilot passive treatment plant was constructed in 1994 at Wheat Jane Mine in Cornwall, UK. The plant consists of three separate systems; each containing aerobic reed beds, anaerobic cell and rock filters, and represents the largest European experimental facility of its kind. The systems only differ by the type of pre-treatment utilised to increase the pH of the influent minewater (pH<4): lime-dosed (LD), anoxic limestone drain (ALD) and lime free (LF), which receives no form of pre-treatment. The Wheal Jane pilot plant offered a unique facility and a major research project was established to evaluate the pilot plant and study in detail the biological mechanisms and the geochemical and physical processes that control passive treatment systems. The project has led to data, knowledge, models and design criteria for the future design, planning and sustainable management of passive treatment systems. A multidisciplinary team of scientists and managers from the U.K. universities, the Environment Agency and the Mining Industry has been put together to obtain the maximum advantage from the excellent facilities facility at Wheal Jane. (C) 2004 Elseaier B.V All rights reserved.

Protection of live bacteria from bile acid toxicity using bile acid adsorbing resins

We previously demonstrated that a dry, room temperature stable formulation of a live bacterial vaccine was highly susceptible to bile, and suggested that this will lead to significant loss of viability of any live bacterial formulation released into the intestine using an enteric coating or capsule. We found that bile and acid tolerance is very rapidly recovered after rehydration with buffer or water, raising the possibility that rehydration in the absence of bile prior to release into the intestine might solve the problem of bile toxicity to dried cells. We describe here a novel formulation that combines extensively studied bile acid adsorbent resins with the dried bacteria, to temporarily adsorb bile acids and allow rehydration and recovery of bile resistance of bacteria in the intestine before release. Tablets containing the bile acid adsorbent cholestyramine release 250-fold more live bacteria when dissolved in a bile solution, compared to control tablets without cholestyramine or with a control resin that does not bind bile acids. We propose that a simple enteric coated oral dosage form containing bile acid adsorbent resins will allow improved live bacterial delivery to the intestine via the oral route, a major step towards room temperature stable, easily administered and distributed vaccine pills and other bacterial therapeutics

Introduction of 4-chloro-alpha-cyanocinnamic acid liquid matrices for high sensitivity UV-MALDI MS

Matrix-assisted laser desorption/ionization (MALDI) is a key ionization technique in mass spectrometry (MS) for the analysis of labile macromolecules. An important area of study and improvements in relation to MALDI and its application in high-sensitivity MS is that of matrix design and sample preparation. Recently, 4-chloro-alpha-cyanocinnamic acid (ClCCA) has been introduced as a new rationally designed matrix and reported to provide an improved analytical performance as demonstrated by an increase in sequence coverage of protein digests obtained by peptide mass mapping (PMM) (Jaskolla, T. W.; et al. Proc. Natl. Acad. Sci. U.S.A. 2008, 105, 12200-12205). This new matrix shows the potential to be a superior alternative to the commonly used and highly successful alpha-cyano-4-hydroxycinnamic acid (CHCA). We have taken this design one step further by developing and optimizing an ionic liquid matrix (ILM) and liquid support matrix (LSM) using ClCCA as the principle chromophore and MALDI matrix compound. These new liquid matrices possess greater sample homogeneity and a simpler morphology. The data obtained from our studies show improved sequence coverage for BSA digests compared to the traditional CHCA crystalline matrix and for the ClCCA-containing ILM a similar performance to the ClCCA crystalline matrix down to 1 fmol of BSA digest prepared in a single MALDI sample droplet with current sensitivity levels in the attomole range. The LSMs show a high tolerance to contamination such as ammonium bicarbonate, a commonly used buffering agent.

Incorporation of cis-9,trans-11 or trans-10,cis-12 conjugated linoleic acid into plasma and cellular lipids in healthy men

This study investigated the incorporation of cis-9,trans-11 conjugated linoleic acid (c9,t11 CLA) and trans-10,cis-12-CLA (t10,c12 CLA) into plasma and peripheral blood mononuclear cell (PBMC) lipids when consumed as supplements highly enriched in these isomers. Healthy men (n = 49, age 31 +/- 8 years) consumed one, two, and four capsules containing similar to600 mg of either c9,t11 CIA or t10,c12 CLA per capsule for sequential 8 week periods followed by a 6 week washout before consuming the alternative isomer. Both isomers were incorporated in a dosedependent manner into plasma phosphatidylcholine (PC) (c9,t11 CLA r = 0.779, t10,c12 CLA r = 0.738; P < 0.0001) and cholesteryl ester (CE) (c9,t11 CLA r = 0.706, t10,c12 CLA r = 0.788; P < 0.0001). Only t10,c12 CLA was enriched in plasma nonesterified fatty acids. Both c9,t11 CIA and t10,c12 CLA were incorporated linearly into PBMC total lipids (r = 0.285 and r = 0.273, respectively; P < 0.0005). The highest concentrations of c9,t11 CLA and t10,c12 CLA in PBMC lipids were 3- to 4-fold lower than those in plasma PC and CE. These data suggest that the level of intake is a major determinant of plasma and PBMC CLA content, although PBMCs appear to incorporate both CLA isomers less readily.

Effect of replacing calcium salts of palm oil distillate with rapeseed oil, milled or whole rapeseeds on milk fatty-acid composition in cows fed maize silage-based diets

Inclusion of rapeseed feeds in dairy cow diets has the potential to reduce milk fat saturated fatty acid (SFA) and increase cis-monounsaturated fatty acid (cis-MUFA) content but effectiveness may depend on the form in which the rapeseed is presented. Four mid-lactation Holstein dairy cows were allocated to four maize silage-based dietary treatments according to a 4 x 4 Latin Square design, with 28-day experimental periods. Treatments consisted of a control diet (C containing 49 g/kg dry matter (DM) of calcium salts of palm oil distillate (CPO), or 49 g/kg DM of oil supplied as whole rapeseeds (WR), rapeseeds milled with wheat (MR) or rapeseed oil (RO). Replacing CPO with rapeseed feeds had no effect (P > 0.05) on milk fat and protein content, while milk yields were higher (P < 0.05) for RO and MR compared with WR (37.1, 38.1 and 34.3 kg/day, respectively). Substituting CPO with RO or MR reduced (P < 0.05) milk fat total SFA content (69.6, 55.6, 71.7 and 61.5 g/100g fatty acids for C, RO, WR and MR, respectively) and enhanced (P < 0.05) milk cis-9 18:1 MUFA concentrations (corresponding values 18.6, 24.3, 17.0 and 23.0 g/100g fatty acids) compared with C and WR. Treatments RO and MR also increased (P < 0.05) milk trans-MUFA content (4.4, 6.8, 10.5 g/100g fatty acids, C MR and RO, respectively). A lack of significant changes in milk fat composition when replacing CPO with WR suggests limited bioavailability of fatty acids in intact rapeseeds. In conclusion, replacing a commercial palm oil-based fat supplement in the diet with milled rapeseeds or rapeseed oil represented an effective strategy to alter milk fatty acid composition with the potential to improve human health. Inclusion of processed rapeseeds offered a good compromise for reducing milk SFA and increasing cis-MUFA, whilst minimising milk trans-MUFA and negative effects on animal performance.

Effect of replacing grass silage with maize silage in the diet on bovine milk fatty acid composition

Even though extensive research has examined the role of nutrition on milk fat composition, there is less information on the impact of forages on milk fatty acid (FA) composition. In the current study, the effect of replacing grass silage (GS) with maize silage (MS) as part of a total mixed ration on animal performance and milk FA composition was examined using eight multiparous mid-lactation cows in a replicated 4 X 4 Latin square with 28-day experimental periods. Four treatments comprised the stepwise replacement of GS with MS (0, 160, 334 and 500 g/kg dry matter (DM)) in diets containing a 54:46 forage: concentrate ratio on a DM basis. Replacing GS with MS increased (P < 0.001) the DM intake, milk yield and milk protein content. Incremental replacement of GS with MS in the diet enhanced linearly (P < 0.001) the proportions of 6:0-14:0, decreased (P < 0.01) the 16:0 concentrations, but had no effect on the total milk fat saturated fatty acid content. Inclusion of MS altered the distribution of trans-18:1 isomers and enhanced (P < 0.05) total trans monounsaturated fatty acid and total conjugated linoleic acid content. Milk total n-3 polyunsaturated fatty acid (PUFA) content decreased with higher amounts of MS in the diet and n-6 PUFA concentration increased, leading to an elevated n-6: n-3 PUFA ratio. Despite some beneficial changes associated with the replacement of GS with MS, the overall effects on milk FA composition would not be expected to substantially improve long-term human health. However the role of forages on milk fat composition must also be balanced against the increases in total milk and protein yield on diets containing higher proportions of MS.

Examination of the persistency of milk fatty acid composition responses to fish oil and sunflower oil in the diet of dairy cows

Based on the potential benefits of cis-9, trans-11 conjugated linoleic acid (CLA) for human health, there is a need to develop effective strategies for enhancing milk fat CLA concentrations. Levels of cis-9, trans-11 CLA in milk can be increased by supplements of fish oil (FO) and sunflower oil (SO), but there is considerable variation in the response. Part of this variance may reflect time-dependent ruminal adaptations to high levels of lipid in the diet, which lead to alterations in the formation of specific biohydrogenation intermediates. To test this hypothesis, 16 late lactation Holstein-British Friesian cows were used in a repeated measures randomized block design to examine milk fatty acid composition responses to FO and SO in the diet over a 28-d period. Cows were allocated at random to corn silage-based rations (8 per treatment) containing 0 (control) or 45 g of oil supplement/ kg of dry matter consisting (1:2; wt/wt) of FO and SO (FSO), and milk composition was determined on alternate days from d 1. Compared with the control, the FSO diet decreased mean dry matter intake (21.1 vs. 17.9 kg/d), milk fat (47.7 vs. 32.6 g/kg), and protein content (36.1 vs. 33.3 g/kg), but had no effect on milk yield (27.1 vs. 26.4 kg/d). Reductions in milk fat content relative to the FSO diet were associated with increases in milk trans-10 18: 1, trans-10, cis-12 CLA, and trans-9, cis-11 CLA concentrations (r(2) = 0.74, 0.57, and 0.80, respectively). Compared with the control, the FSO diet reduced milk 4: 0 to 18: 0 and cis 18:1 content and increased trans 18:1, trans 18:2, cis-9, trans-11 CLA, 20: 5 n-3, and 22: 6 n-3 concentrations. The FSO diet caused a rapid elevation in milk cis-9, trans-11 CLA content, reaching a maximum of 5.37 g/100 g of fatty acids on d 5, but these increases were transient, declining to 2.35 g/100 g of fatty acids by d 15. They remained relatively constant thereafter. Even though concentrations of trans-11 18: 1 followed the same pattern of temporal changes as cis-9, trans-11 CLA, the total trans 18:1 content of FSO milk was unchanged because of the concomitant increases in the concentration of other isomers (Delta(4-10) and Delta(12-15)), predominantely trans-10 18:1. In conclusion, supplementing diets with FSO enhances milk fat cis-9, trans-11 CLA content, but the high level of enrichment declines because of changes in ruminal biohydrogenation that result in trans-10 replacing trans-11 as the major 18:1 biohydrogenation intermediate formed in the rumen.

Effect of feeding supplemental fibrolytic enzymes or soluble sugars with malic acid on milk production

Two trials were conducted to evaluate effects of feeding supplemental fibrolytic enzymes or soluble sugars and malic acid on milk production. In trial 1, 257 cows at four sites were fed a basal diet consisting of no more than 60% of forage DM as corn silage and less than 40% as alfalfa hay. Cows were assigned randomly within site, parity, and two stages of lactation to: 1) control; 2) enzyme A; 3) enzyme B; and 4) soluble sugars and malic acid. There was a 14-d pretreatment and an 84-d treatment period. Enzyme solutions were sprayed on either the forage component or the TMR each day while mixing feed. Trial 2 was similar, except 122 cows at one site in the United Kingdom were fed diets containing forage that was 75% corn silage and 25% grass silage, and all cows began the study between 25 to 31 DIM. Mean milk productions for 233 cows that completed trial 1 were 32.9, 32.5, 32.4, and 32.9 kg/d for control, enzyme A, enzyme B, and soluble sugars and malic acid, respectively. Mean milk productions for 116 cows that completed trial 2 were 28.2, 27.9, 28.8, and 28.4 kg/d, respectively. In vitro analyses of the activities of enzyme solutions indicated that all major cellulose and hemicellulose degrading activities were present; however, the pH optima (approximate pH = 4 to 5) were more acidic, and the temperature optimum (approximately 50 C) was greater than normal pH and temperature in the rumen. If fibrolytic activity in the rumen is a major mechanism of action of supplemental fibrolytic enzymes, it appears that considerable activity of these preparations was lost due to conditions in the rumen. In conclusion, feeding supplemental fibrolytic enzymes or malic acid with soluble sugars had no effect on milk production under the conditions used in this study.