CHARACTERIZATION AND CLASSIFICATION OF SOILS IN THE TAQUARI RIVER BASIN - PANTANAL REGION, STATE OF MATO GROSSO DO SUL, BRAZIL

Among the soils in the Mato Grosso do Sul, stand out in the Pantanal biome, the Spodosols. Despite being recorded in considerable extensions, few studies aiming to characterize and classify these soils were performed. The purpose of this study was to characterize and classify soils in three areas of two physiographic types in the Taquari river basin: bay and flooded fields. Two trenches were opened in the bay area (P1 and P2) and two in the flooded field (P3 and P4). The third area (saline) with high sodium levels was sampled for further studies. In the soils in both areas the sand fraction was predominant and the texture from sand to sandy loam, with the main constituent quartz. In the bay area, the soil organic carbon in the surface layer (P1) was (OC) > 80 g kg(-1), being diagnosed as Histic epipedon. In the other profiles the surface horizons had low OC levels which, associated with other properties, classified them as Ochric epipedons. In the soils of the bay area (P1 and P2), the pH ranged from 5.0 to 7.5, associated with dominance of Ca2+ and Mg2+, with base saturation above 50 % in some horizons. In the flooded fields (P3 and P4) the soil pH ranged from 4.9 to 5.9, H+ contents were high in the surface horizons (0.8-10.5 cmol(c) kg(-1)), Ca2+ and Mg-2 contents ranged from 0.4 to 0.8 cmol(c) kg(-1) and base saturation was < 50 %. In the soils of the bay area (P1 and P2) iron was accumulated (extracted by dithionite - Fed) and OC in the spodic horizon; in the P3 and P4 soils only Fed was accumulated (in the subsurface layers). According to the criteria adopted by the Brazilian System of Soil Classification (SiBCS) at the subgroup level, the soils were classified as: P1: Organic Hydromorphic Ferrohumiluvic Spodosol. P2: Typical Orthic Ferrohumiluvic Spodosol. P3: Typical Hydromorphic Ferroluvic Spodosol. P4: Arenic Orthic Ferroluvic Spodosol.

Different protocols to produce artificial dentine carious lesions in vitro and in situ: hardness and mineral content correlation

This study compared dentine demineralization induced by in vitro and in situ models, and correlated dentine surface hardness (SH), cross-sectional hardness (CSH) and mineral content by transverse microradiography (TMR). Bovine dentine specimens (n = 15/group) were demineralized in vitro with the following: MC gel (6% carboxymethylcellulose gel and 0.1 m lactic acid, pH 5.0, 14 days); buffer I (0.05 m acetic acid solution with calcium, phosphate and fluoride, pH 4.5, 7 days); buffer II (0.05 m acetic acid solution with calcium and phosphate, pH 5.0, 7 days), and TEMDP (0.05 m lactic acid with calcium, phosphate and tetraethyl methyl diphosphonate, pH 5.0, 7 days). In an in situ study, 11 volunteers wore palatal appliances containing 2 bovine dentine specimens, protected with a plastic mesh to allow biofilm development. The volunteers dripped a 20% sucrose solution on each specimen 4 times a day for 14 days. In vitro and in situ lesions were analyzed using TMR and statistically compared by ANOVA. TMR and CSH/SH were submitted to regression and correlation analysis (p < 0.05). The in situ model produced a deep lesion with a high R value, but with a thin surface layer. Regarding the in vitro models, MC gel produced only a shallow lesion, while buffers I and II as well as TEMDP induced a pronounced subsurface lesion with deep demineralization. The relationship between CSH and TMR was weak and not linear. The artificial dentine carious lesions induced by the different models differed significantly, which in turn might influence further de- and remineralization processes. Hardness analysis should not be interpreted with respect to dentine mineral loss

Characterization and classification of soils in the Taquari river basin - Pantanal region, state of Mato Grosso do Sul, Brazil

Among the soils in the Mato Grosso do Sul, stand out in the Pantanal biome, the Spodosols. Despite being recorded in considerable extensions, few studies aiming to characterize and classify these soils were performed. The purpose of this study was to characterize and classify soils in three areas of two physiographic types in the Taquari river basin: bay and flooded fields. Two trenches were opened in the bay area (P1 and P2) and two in the flooded field (P3 and P4). The third area (saline) with high sodium levels was sampled for further studies. In the soils in both areas the sand fraction was predominant and the texture from sand to sandy loam, with the main constituent quartz. In the bay area, the soil organic carbon in the surface layer (P1) was (OC) > 80 g kg-1, being diagnosed as Histic epipedon. In the other profiles the surface horizons had low OC levels which, associated with other properties, classified them as Ochric epipedons. In the soils of the bay area (P1 and P2), the pH ranged from 5.0 to 7.5, associated with dominance of Ca2+ and Mg2+, with base saturation above 50 % in some horizons. In the flooded fields (P3 and P4) the soil pH ranged from 4.9 to 5.9, H+ contents were high in the surface horizons (0.8-10.5 cmol c kg-1 ), Ca2+ and Mg² contents ranged from 0.4 to 0.8 cmol c kg-1 and base saturation was < 50 %. In the soils of the bay area (P1 and P2) iron was accumulated (extracted by dithionite - Fed) and OC in the spodic horizon; in the P3 and P4 soils only Fed was accumulated (in the subsurface layers). According to the criteria adopted by the Brazilian System of Soil Classification (SiBCS) at the subgroup level, the soils were classified as: P1: Organic Hydromorphic Ferrohumiluvic Spodosol. P2: Typical Orthic Ferrohumiluvic Spodosol. P3: Typical Hydromorphic Ferroluvic Spodosol. P4: Arenic Orthic Ferroluvic Spodosol.

Asignación de profundidad significativa a las observaciones remotas de la temperatura superficial del mar

Se asigna una profundidad efectiva para las medidas de temperatura superficial del mar obtenida mediante AVHRR en aguas del Atlántico Centro-Oriental. Las distribuciones espaciales de temperatura a cierta profundidad pueden definirse por satélite. En la mesoescala (l° mes) y para una precisión absoluta de 1ºK. Se encuentra que el espesor de la capa homogénea varía entre unos 100 m en febrero aproximadamente 20m de septiembre. ABSTRACT: Using a 11 years time series of monthly mean AVHRR sea surface temperatures and a comparable time series of XBT data for Central Eastem Atlantic, a representative depth is assigned to satellite measurements. At mesoscale (1 degree, month resolution) the thickness of fue homogeneous surface layer varíes from approximately 100 m in February to only 20 m in september, for an accuracy of loK in the temperature deterrnination.

Zooplankton oxygen consumption and nutrient release in relation to species composition, animals size and enviromental conditions in the Baltic Sea during May and August

[EN] Zooplankton metabolism in terms of oxygen consumption and ñutrient reléase (ammonia, phosphate) were measiu'ed in the Baltic Sea, a températe área with high envirormiental changes both in space and in time. Plankton of the surface layer were analysed with balance measurements in 4 size classes between 50 and 1000 nm during spring in 1988, 1990 and 1991, in summer 19^8 and 1990 as well. The use of electrón transport system (ETS), and the Glutamate Dehydrogenase (GDH) activity as indicators for respiration and ammonia reléase respectively, enlarged the data density and made a three dimensional resolution available (May 1990, 1991). Data are in the range of the latitudinal dependend magnitude. They reflect slight interannual, more seasonal and regional aspects. Animáis size, temperature, food concentration, and species composition influence the specific rates

Astronomical site testing in the era of the extremely large telescopes

The quality of astronomical sites is the first step to be considered to have the best performances from the telescopes. In particular, the efficiency of large telescopes in UV, IR, radio etc. is critically dependent on atmospheric transparency. It is well known that the random optical effects induced on the light propagation by turbulent atmosphere also limit telescope’s performances. Nowadays, clear appears the importance to correlate the main atmospheric physical parameters with the optical quality reachable by large aperture telescopes. The sky quality evaluation improved with the introduction of new techniques, new instrumentations and with the understanding of the link between the meteorological (or synoptical parameters and the observational conditions thanks to the application of the theories of electromagnetic waves propagation in turbulent medias: what we actually call astroclimatology. At the present the site campaigns are evolved and are performed using the classical scheme of optical seeing properties, meteorological parameters, sky transparency, sky darkness and cloudiness. New concept are added and are related to the geophysical properties such as seismicity, microseismicity, local variability of the climate, atmospheric conditions related to the ground optical turbulence and ground wind regimes, aerosol presence, use of satellite data. The purpose of this project is to provide reliable methods to analyze the atmospheric properties that affect ground-based optical astronomical observations and to correlate them with the main atmospheric parameters generating turbulence and affecting the photometric accuracy. The first part of the research concerns the analysis and interpretation of longand short-time scale meteorological data at two of the most important astronomical sites located in very different environments: the Paranal Observatory in the Atacama Desert (Chile), and the Observatorio del Roque de Los Muchachos(ORM) located in La Palma (Canary Islands, Spain). The optical properties of airborne dust at ORM have been investigated collecting outdoor data using a ground-based dust monitor. Because of its dryness, Paranal is a suitable observatory for near-IR observations, thus the extinction properties in the spectral range 1.00-2.30 um have been investigated using an empirical method. Furthermore, this PhD research has been developed using several turbulence profilers in the selection of the site for the European Extremely Large Telescope(E-ELT). During the campaigns the properties of the turbulence at different heights at Paranal and in the sites located in northern Chile and Argentina have been studied. This given the possibility to characterize the surface layer turbulence at Paranal and its connection with local meteorological conditions.

Methoden und Modelle zur Phytoplanktonanalyse am Beispiel einer Restaurierungsmaßnahme an der Bleiloch Talsperre

Methoden und Modelle zur Phytoplanktonanalyse am Beispiel einer Restaurierungsmaßnahme an der Bleiloch Talsperre Zusammenfassung An der hypertrophen Bleiloch Talsperre (Thüringen, BRD) werden die Auswirkungen der 1997 in Betrieb genommenen partiellen Destratifikation (0- 20m) untersucht. Ziel der Maßnahme war die Hemmung des Phytoplanktonwachstums durch Lichtlimitation.Da es nicht gelang, auch die Oberflächenlammelle in die Durchmischung einzubeziehen, wurde auch keine Reduktion des Phytoplanktons beobachtet. Seine zeitliche Dynamik nahm deutlich zu und es traten neben typischen Längsgradienten auch extreme, kleinräumige Konzentrationsunterschiede auf. Die vorher häufigen Cyanobakterien spielten jedoch keine quantitativ bedeutsame Rolle mehr. Es wird diskutiert, wie die Belüftung die Saisonalität des Planktons stört und zu Verschiebungen der Zusammensetzung führt. Der Zusammenhang zwischen der Chlorophyll a Menge und der Stabilität der Wassersäule sowie der Einfluß wachstumsbestimmender Größen werden modelliert. Methodische Schwerpunkte umfassen die Auswertung von Phytoplankton-Pigmentdaten (HPLC-Analyse) und die Entwicklung einer Durchflußzytometer-Methode. Bei letzerer werden an lebenden Phytoplanktern die Vorwärtsstreuung sowie vier Fluoreszenzen (2 Phycoerythrine, Phycocyanin und Chlorophyll a, 514nm Anregungswellenlänge) gemessen. Zur Klassifizierung von Algen anhand von Referenzen werden zwei Methoden entwickelt, Möglichkeiten des Sortierens aufgezeigt und es wird ein Vergleich mit Mikroskopie und HPLC- Pigmentanalyse durchgeführt. Anhand von Modellrechnungen wird demonstriert, wie sich systematische bzw. zufällige Abweichungen der Pigmentstöchiometrien auf die Berechnung von Algengruppenanteilen auswirken. Strategien zur Auswertung von Pigmentdaten werden empfohlen.

Synthesis and characterisation of photoreactive silanes for the self-assembly on functionalised silica surfaces

The aim of this thesis was to investigate novel techniques to create complex hierarchical chemical patterns on silica surfaces with micro to nanometer sized features. These surfaces were used for a site-selective assembly of colloidal particles and oligonucleotides. To do so, functionalised alkoxysilanes (commercial and synthesised ones) were deposited onto planar silica surfaces. The functional groups can form reversible attractive interactions with the complementary surface layers of the opposing objects that need to be assembled. These interactions determine the final location and density of the objects onto the surface. Photolithographically patterned silica surfaces were modified with commercial silanes, in order to create hydrophilic and hydrophobic regions on the surface. Assembly of hydrophobic silica particles onto these surfaces was investigated and finally, pH and charge effects on the colloidal assembly were analysed. In the second part of this thesis the concept of novel, "smart" alkoxysilanes is introduced that allows parallel surface activation and patterning in a one-step irradiation process. These novel species bear a photoreactive head-group in a protected form. Surface layers made from these molecules can be irradiated through a mask to remove the protecting group from selected regions and thus generate lateral chemical patterns of active and inert regions on the substrate. The synthesis of an azide-reactive alkoxysilane was successfully accomplished. Silanisation conditions were carefully optimised as to guarantee a smooth surface layer, without formation of micellar clusters. NMR and DLS experiments corroborated the absence of clusters when using neither water nor NaOH as catalysts during hydrolysis, but only the organic solvent itself. Upon irradiation of the azide layer, the resulting nitrene may undergo a variety of reactions depending on the irradiation conditions. Contact angle measurements demonstrated that the irradiated surfaces were more hydrophilic than the non-irradiated azide layer and therefore the formation of an amine upon irradiation was postulated. Successful photoactivation could be demonstrated using condensation patterns, which showed a change in wettability on the wafer surface upon irradiation. Colloidal deposition with COOH functionalised particles further underlined the formation of more hydrophilic species. Orthogonal photoreactive silanes are described in the third part of this thesis. The advantage of orthogonal photosensitive silanes is the possibility of having a coexistence of chemical functionalities homogeneously distributed in the same layer, by using appropriate protecting groups. For this purpose, a 3',5'-dimethoxybenzoin protected carboxylic acid silane was successfully synthesised and the kinetics of its hydrolysis and condensation in solution were analysed in order to optimise the silanisation conditions. This compound was used together with a nitroveratryl protected amino silane to obtain bicomponent surface layers. The optimum conditions for an orthogonal deprotection of surfaces modified with this two groups were determined. A 2-step deprotection process through a mask generated a complex pattern on the substrate by activating two different chemistries at different sites. This was demonstrated by colloidal adsorption and fluorescence labelling of the resulting substrates. Moreover, two different single stranded oligodeoxynucleotides were immobilised onto the two different activated areas and then hybrid captured with their respective complementary, fluorescent labelled strand. Selective hybridisation could be shown, although non-selective adsorption issues need to be resolved, making this technique attractive for possible DNA microarrays.

Performance evaluation of low environmental impact asphalt concretes using the mechanistic empirical design method based on laboratory fatigue and permanent deformation models

The "sustainability" concept relates to the prolonging of human economic systems with as little detrimental impact on ecological systems as possible. Construction that exhibits good environmental stewardship and practices that conserve resources in a manner that allow growth and development to be sustained for the long-term without degrading the environment are indispensable in a developed society. Past, current and future advancements in asphalt as an environmentally sustainable paving material are especially important because the quantities of asphalt used annually in Europe as well as in the U.S. are large. The asphalt industry is still developing technological improvements that will reduce the environmental impact without affecting the final mechanical performance. Warm mix asphalt (WMA) is a type of asphalt mix requiring lower production temperatures compared to hot mix asphalt (HMA), while aiming to maintain the desired post construction properties of traditional HMA. Lowering the production temperature reduce the fuel usage and the production of emissions therefore and that improve conditions for workers and supports the sustainable development. Even the crumb-rubber modifier (CRM), with shredded automobile tires and used in the United States since the mid 1980s, has proven to be an environmentally friendly alternative to conventional asphalt pavement. Furthermore, the use of waste tires is not only relevant in an environmental aspect but also for the engineering properties of asphalt [Pennisi E., 1992]. This research project is aimed to demonstrate the dual value of these Asphalt Mixes in regards to the environmental and mechanical performance and to suggest a low environmental impact design procedure. In fact, the use of eco-friendly materials is the first phase towards an eco-compatible design but it cannot be the only step. The eco-compatible approach should be extended also to the design method and material characterization because only with these phases is it possible to exploit the maximum potential properties of the used materials. Appropriate asphalt concrete characterization is essential and vital for realistic performance prediction of asphalt concrete pavements. Volumetric (Mix design) and mechanical (Permanent deformation and Fatigue performance) properties are important factors to consider. Moreover, an advanced and efficient design method is necessary in order to correctly use the material. A design method such as a Mechanistic-Empirical approach, consisting of a structural model capable of predicting the state of stresses and strains within the pavement structure under the different traffic and environmental conditions, was the application of choice. In particular this study focus on the CalME and its Incremental-Recursive (I-R) procedure, based on damage models for fatigue and permanent shear strain related to the surface cracking and to the rutting respectively. It works in increments of time and, using the output from one increment, recursively, as input to the next increment, predicts the pavement conditions in terms of layer moduli, fatigue cracking, rutting and roughness. This software procedure was adopted in order to verify the mechanical properties of the study mixes and the reciprocal relationship between surface layer and pavement structure in terms of fatigue and permanent deformation with defined traffic and environmental conditions. The asphalt mixes studied were used in a pavement structure as surface layer of 60 mm thickness. The performance of the pavement was compared to the performance of the same pavement structure where different kinds of asphalt concrete were used as surface layer. In comparison to a conventional asphalt concrete, three eco-friendly materials, two warm mix asphalt and a rubberized asphalt concrete, were analyzed. The First Two Chapters summarize the necessary steps aimed to satisfy the sustainable pavement design procedure. In Chapter I the problem of asphalt pavement eco-compatible design was introduced. The low environmental impact materials such as the Warm Mix Asphalt and the Rubberized Asphalt Concrete were described in detail. In addition the value of a rational asphalt pavement design method was discussed. Chapter II underlines the importance of a deep laboratory characterization based on appropriate materials selection and performance evaluation. In Chapter III, CalME is introduced trough a specific explanation of the different equipped design approaches and specifically explaining the I-R procedure. In Chapter IV, the experimental program is presented with a explanation of test laboratory devices adopted. The Fatigue and Rutting performances of the study mixes are shown respectively in Chapter V and VI. Through these laboratory test data the CalME I-R models parameters for Master Curve, fatigue damage and permanent shear strain were evaluated. Lastly, in Chapter VII, the results of the asphalt pavement structures simulations with different surface layers were reported. For each pavement structure, the total surface cracking, the total rutting, the fatigue damage and the rutting depth in each bound layer were analyzed.

Unconventional superconductivity of the heavy fermion compound UNi 2 Al 3

The heavy fermion compound UNi2Al3 exhibits the coexistence of superconductivity and magnetic order at low temperatures, stimulating speculations about possible exotic Cooper-pairing interaction in this superconductor. However, the preparation of good quality bulk single crystals of UNi2Al3 has proven to be a non-trivial task due to metallurgical problems, which result in the formation of an UAl2 impurity phase and hence a strongly reduced sample purity. The present work concentrates on the preparation, characterization and electronic properties investigation of UNi2Al3 single crystalline thin film samples. The preparation of thin films was accomplished in a molecular beam epitaxy (MBE) system. (100)-oriented epitaxial thin films of UNi2Al3 were grown on single crystalline YAlO3 substrates cut in (010)- or (112)-direction. The high crystallographic quality of the samples was proved by several characterisation methods, such as X-ray analysis, RHEED and TEM. To study the magnetic structure of epitaxial thin films resonant magnetic x-ray scattering was employed. The magnetic order of thin the film samples, the formation of magnetic domains with different moment directions, and the magnetic correlation length were discussed. The electronic properties of the UNi2Al3 thin films in the normal and superconducting states were investigated by means of transport measurements. A pronounced anisotropy of the temperature dependent resistivity ρ(T) was observed. Moreover, it was found that the temperature of the resistive superconducting transition depends on the current direction, providing evidence for multiband superconductivity in UNi2Al3. The initial slope of the upper critical field H′c2(T) of the thin film samples suggests an unconventional spin-singlet superconducting state, as opposed to bulk single crystal data. To probe the superconducting gap of UNi2Al3 directly by means of tunnelling spectroscopy many planar junctions of different design employing different techniques were prepared. Despite the tunneling regime of the junctions, no features of the superconducting density of state of UNi2Al3 were ever observed. It is assumed that the absence of UNi2Al3 gap features in the tunneling spectra was caused by imperfections of the tunnelling contacts. The superconductivity of UNi2Al3 was probably suppressed just in a degraded surface layer, resulting in tunneling into non superconducting UNi2Al3. However, alternative explanations such as intrinsic pair breaking effects at the interface to the barrier are also possible.

Aeolian geomorphodynamics in endorheic basins of the Mongolian Gobi Desert

Die vorliegende Arbeit ist im Zuge des DFG Projektes Spätpleistozäne, holozäne und aktuelle Geomorphodynamik in abflusslosen Becken der Mongolischen Gobi´´ entstanden. Das Arbeitsgebiet befindet sich in der südlichen Mongolei im nördlichen Teil der Wüste Gobi. Neben einigen Teilen der Sahara (Heintzenberg, 2009), beispielsweise das Bodélé Becken des nördlichen Tschads (z.B. Washington et al., 2006a; Todd et al., 2006; Warren et al., 2007) wird Zentralasien als ein Hauptliefergebiet für Partikel in die globale Zirkulation der Atmosphäre gesehen (Goudie, 2009). Hauptaugenmerk liegt hierbei besonders auf den abflusslosen Becken und deren Sedimentablagerungen. Die, der Deflation ausgesetzten Flächen der Seebecken, sind hauptsächliche Quelle für Partikel die sich in Form von Staub respektive Sand ausbreiten. Im Hinblick auf geomorphologische Landschaftsentwicklung wurde der Zusammenhang von Beckensedimenten zu Hangdepositionen numerisch simuliert. Ein von Grunert and Lehmkuhl (2004) publiziertes Model, angelehnt an Ideen von Pye (1995) wird damit in Betracht gezogen. Die vorliegenden Untersuchungen modellieren Verbreitungsmechanismen auf regionaler Ebene ausgehend von einer größeren Anzahl an einzelnen punktuellen Standorten. Diese sind repräsentativ für die einzelnen geomorphologischen Systemglieder mit möglicherweise einer Beteiligung am Budget aeolischer Geomorphodynamik. Die Bodenbedeckung durch das charakteristische Steinpflaster der Gobi - Region, sowie unter anderem Korngrößenverteilungen der Oberflächensedimente wurden untersucht. Des Weiteren diente eine zehnjährige Zeitreihe (Jan 1998 bis Dez 2007) meteorologischer Daten als Grundlage zur Analyse der Bedingungen für äolische Geomorphodynamik. Die Daten stammen von 32 staatlichen mongolischen Wetterstationen aus der Region und Teile davon wurden für die Simulationen verwendet. Zusätzlich wurden atmosphärische Messungen zur Untersuchung der atmosphärischen Stabilität und ihrer tageszeitlichen Variabilität mit Mess-Drachenaufstiegen vorgenommen. Die Feldbefunde und auch die Ergebnisse der Laboruntersuchungen sowie der Datensatz meteorologischer Parameter dienten als Eingangsparameter für die Modellierungen. Emissionsraten der einzelnen Standorte und die Partikelverteilung im 3D Windfeld wurden modelliert um die Konvektivität der Beckensedimente und Hangdepositionen zu simulieren. Im Falle hoher mechanischer Turbulenz der bodennahen Luftschicht (mit einhergehender hoher Wind Reibungsgeschwindigkeit), wurde generell eine neutrale Stabilität festgestellt und die Simulationen von Partikelemission sowie deren Ausbreitung und Deposition unter neutraler Stabilitätsbedingung berechnet. Die Berechnung der Partikelemission wurde auf der Grundlage eines sehr vereinfachten missionsmodells in Anlehnung an bestehende Untersuchungen (Laurent et al., 2006; Darmenova et al., 2009; Shao and Dong, 2006; Alfaro, 2008) durchgeführt. Sowohl 3D Windfeldkalkulationen als auch unterschiedliche Ausbreitungsszenarien äolischer Sedimente wurden mit dem kommerziellen Programm LASAT® (Lagrange-Simulation von Aerosol-Transport) realisiert. Diesem liegt ein Langargischer Algorithmus zugrunde, mittels dessen die Verbreitung einzelner Partikel im Windfeld mit statistischer Wahrscheinlichkeit berechnet wird. Über Sedimentationsparameter kann damit ein Ausbreitungsmodell der Beckensedimente in Hinblick auf die Gebirgsfußflächen und -hänge generiert werden. Ein weiterer Teil der Untersuchungen beschäftigt sich mit der geochemischen Zusammensetzung der Oberflächensedimente. Diese Proxy sollte dazu dienen die simulierten Ausbreitungsrichtungen der Partikel aus unterschiedlichen Quellregionen nach zu verfolgen. Im Falle der Mongolischen Gobi zeigte sich eine weitestgehende Homogenität der Minerale und chemischen Elemente in den Sedimenten. Laser Bebohrungen einzelner Sandkörner zeigten nur sehr leichte Unterschiede in Abhängigkeit der Quellregionen. Die Spektren der Minerale und untersuchten Elemente deuten auf graitische Zusammensetzungen hin. Die, im Untersuchungsgebiet weit verbreiteten Alkali-Granite (Jahn et al., 2009) zeigten sich als hauptverantwortlich für die Sedimentproduktion im Untersuchungsgebiet. Neben diesen Mineral- und Elementbestimmungen wurde die Leichtmineralfraktion auf die Charakteristik des Quarzes hin untersucht. Dazu wurden Quarzgehalt, Kristallisation und das Elektronen-Spin-Resonanz Signal des E’1 - Centers in Sauerstoff Fehlstellungen des SiO2 Gitters bestimmt. Die Untersuchungen sind mit dem Methodenvorschlag von Sun et al. (2007) durchgeführt worden und sind prinzipiell gut geeignet um Herkunftsanalysenrndurchzuführen. Eine signifikante Zuordnung der einzelnen Quellgebiete ist jedoch auch in dieser Proxy nicht zu finden gewesen.

Excessive erythrocytosis compromises the blood-endothelium interface in erythropoietin-overexpressing mice

Elevated systemic haematocrit (Hct) increases risk of cardiovascular disorders, such as stroke and myocardial infarction. One possible pathophysiological mechanism could be a disturbance of the blood-endothelium interface. It has been shown that blood interacts with the endothelial surface via a thick hydrated macromolecular layer (the 'glycocalyx', or 'endothelial surface layer'--ESL), modulating various biological processes, including inflammation, permeability and atherosclerosis. However, the consequences of elevated Hct on the functional properties of this interface are incompletely understood. Thus, we combined intravital microscopy of an erythropoietin overexpressing transgenic mouse line (tg6) with excessive erythrocytosis (Hct 0.85), microviscometric analysis of haemodynamics, and a flow simulation model to assess the effects of elevated Hct on glycocalyx/ESL thickness and flow resistance. We show that the glycocalyx/ESL is nearly abolished in tg6 mice (thickness: wild-type control: 0.52 μm; tg6: 0.13 μm; P < 0.001). However, the corresponding reduction in network flow resistance contributes <20% to the maintenance of total peripheral resistance observed in tg6 mice. This suggests that the pathological effects of elevated Hct in these mice, and possibly also in polycythaemic humans, may relate to biological corollaries of a reduced ESL thickness and the consequent alteration in the blood-endothelium interface, rather than to an increase of flow resistance.

Infiltration of Natural Caries Lesions in Relation to Their Activity Status and Acid Pretreatment in vitro

This study aimed at testing how active and inactive enamel caries lesions differ by their degree of resin infiltration, and whether the choice of acid pretreatment plays a crucial role. Four examiners assessed 104 human molars and premolars with noncavitated enamel lesions and classified them as 'active' or 'inactive' using the Nyvad criteria. Forty-five teeth were included in this study after independent unanimous lesion activity assessment. Lesions were cut perpendicularly into 2 halves. Each half lesion was pretreated with either 15% hydrochloric acid or 35% phosphoric acid. The lesions were infiltrated after staining with rhodamine isothiocyanate. Thin sections of 100 µm were prepared and the specimens were bleached with 30% hydrogen peroxide. The specimens were then counterstained with sodium fluorescein, subjected to confocal laser scanning microscopy and analyzed quantitatively. Outcome parameters were maximum and average infiltration depths as well as relative penetration depths and areas. In active lesions no significant difference of percentage maximum penetration depth and percentage average penetration depth between lesions pretreated with hydrochloric or phosphoric acid could be observed. In inactive lesions, however, phosphoric acid pretreatment resulted in significantly lower penetration compared to hydrochloric acid pretreatment. Surface conditioning with hydrochloric acid led to similar infiltration results in active and inactive lesions. Moreover, inactive lesions showed greater variability in all assessed infiltration parameters than did active lesions. In conclusion, caries lesion activity and acid pretreatment both influenced the infiltration. The use of phosphoric acid to increase permeability of the surface layer of active lesions should be further explored.

Modeling of temperature and turbidity in a natural lake and a reservoir connected by pumped-storage operations

Pumped-storage (PS) systems are used to store electric energy as potential energy for release during peak demand. We investigate the impacts of a planned 1000 MW PS scheme connecting Lago Bianco with Lago di Poschiavo (Switzerland) on temperature and particle mass concentration in both basins. The upper (turbid) basin is a reservoir receiving large amounts of fine particles from the partially glaciated watershed, while the lower basin is a much clearer natural lake. Stratification, temperature and particle concentrations in the two basins were simulated with and without PS for four different hydrological conditions and 27 years of meteorological forcing using the software CE-QUAL-W2. The simulations showed that the PS operations lead to an increase in temperature in both basins during most of the year. The increase is most pronounced (up to 4°C) in the upper hypolimnion of the natural lake toward the end of summer stratification and is partially due to frictional losses in the penstocks, pumps and turbines. The remainder of the warming is from intense coupling to the atmosphere while water resides in the shallower upper reservoir. These impacts are most pronounced during warm and dry years, when the upper reservoir is strongly heated and the effects are least concealed by floods. The exchange of water between the two basins relocates particles from the upper reservoir to the lower lake, where they accumulate during summer in the upper hypolimnion (10 to 20 mg L−1) but also to some extent decrease light availability in the trophic surface layer.

Evaluation of reparative cartilage after autologous chondrocyte implantation for osteochondritis dissecans: histology, biochemistry, and MR imaging

BACKGROUND: The aim of this study was to investigate the biochemical properties, histological and immunohistochemical appearance, and magnetic resonance (MR) imaging findings of reparative cartilage after autologous chondrocyte implantation (ACI) for osteochondritis dissecans (OCD). METHODS: Six patients (mean age 20.2 +/- 8.8 years; 13-35 years) who underwent ACI for full-thickness cartilage defects of the femoral condyle were studied. One year after the procedure, a second-look arthroscopic operation was performed with biopsy of reparative tissue. The International Cartilage Repair Society (ICRS) visual histological assessment scale was used for histological assessment. Biopsied tissue was immunohistochemically analyzed with the use of monoclonal antihuman collagen type I and monoclonal antihuman collagen type II primary antibodies. Glycosaminoglycan (GAG) concentrations in biopsied reparative cartilage samples were measured by high performance liquid chromatography (HPLC). MR imaging was performed with T1- and T2-weighted imaging and three-dimensional spoiled gradient-recalled (3D-SPGR) MR imaging. RESULTS: Four tissue samples were graded as having a mixed morphology of hyaline and fibrocartilage while the other two were graded as fibrocartilage. Average ICRS scores for each criterion were (I) 1.0 +/- 1.5; (II) 1.7 +/- 0.5; (III) 0.6 +/- 1.0; (IV) 3.0 +/- 0.0; (V) 1.8 +/- 1.5; and (VI) 2.5 +/- 1.2. Average total score was 10.7 +/- 2.8. On immunohistochemical analysis, the matrix from deep and middle layers of reparative cartilage stained positive for type II collagen; however, the surface layer did not stain well. The average GAG concentration in reparative cartilage was 76.6 +/- 4.2 microg/mg whereas that in normal cartilage was 108 +/- 11.2 microg/mg. Common complications observed on 3D-SPGR MR imaging were hypertrophy of grafted periosteum, edema-like signal in bone marrow, and incomplete repair of subchondral bone at the surgical site. Clinically, patients had significant improvements in Lysholm scores. CONCLUSIONS: In spite of a good clinical course, reparative cartilage after ACI had less GAG concentration and was inferior to healthy hyaline cartilage in histological and immunohistochemical appearance and on MRI findings.