The attrition behaviour of oxygen-carriers under inert and reacting conditions

The attrition of two potential oxygen-carriers for chemical-looping, 100. wt% mechanically-mixed, unsupported iron oxide (400-600 μm diameter) and 25. wt% copper oxide impregnated on alumina (600-900 μm diameter), has been studied. The rates of attrition of batches of these particles whilst they were being fluidised and subjected to successive cycles of reduction and oxidation were determined by measuring the rate of production of fine particles elutriated from the bed, as well as progressive changes in the distribution of particle sizes retained in the bed. The ability of the particles to withstand impacts was also investigated by examining the degree of fragmentation of 1. g of reacted particles of known size on projecting them at a target at various velocities. It was found that the mechanical strength of the iron oxide particles deteriorated significantly after repeated cycles of oxidation and reduction. Thus, the rate of elutriation increased ~35-fold between the 1st and 10th cycle. At an impact velocity of 38. m/s, the amount of fragmentation in the impact test, viz. mass fraction of particles after impact having a size less than that before impact, increased from ~2.3. wt% (fresh particles) to 98. wt% after the 10th cycle. The CuO particles, in comparison, were able to withstand repeated reaction: no signs of increased rates of elutriation or fragmentation were observed over ten cycles. These results highlight the importance of selecting a durable support for oxygen-carriers. © 2011 Elsevier Ltd.

Complex chemistry DNS of n-heptane spray autoignition at high pressure and intermediate temperature conditions

Direct Numerical Simulations (DNS) of turbulent n-heptane sprays autoigniting at high pressure (P=24bar) and intermediate air temperature (Tair=1000K) have been performed to investigate the physical mechanisms present under conditions where low-temperature chemistry is expected to be important. The initial turbulence in the carrier gas, the global equivalence ratio in the spray region, and the initial droplet size distribution of the spray were varied. Results show that spray ignition exhibits a spotty nature, with several kernels developing independently in those regions where the mixture fraction is close to its most reactive value ξMR (as determined from homogeneous reactor calculations) and the scalar dissipation rate is low. Turbulence reduces the ignition delay time as it promotes mixing between air and the fuel vapor, eventually resulting in lower values of scalar dissipation. High values of the global equivalence ratio are responsible for a larger number of ignition kernels, due to the higher probability of finding regions where ξ=ξMR. Spray polydispersity results in the occurrence of ignition over a wider range of mixture fraction values. This is a consequence of the inhomogeneities in the mixing field that characterize these sprays, where poorly mixed rich spots are seen to alternate with leaner ones which are well-mixed. The DNS simulations presented in this work have also been used to assess the applicability of the Conditional Moment Closure (CMC) method to the simulation of spray combustion. CMC is found to be a valid method for capturing spray autoignition, although care should be taken in the modelling of the unclosed terms appearing in the CMC equations. © 2013 The Combustion Institute.

Measurement of the unburnt gas temperature in an IC engine by means of a pressure transducer

A novel method of measuring cylinder gas temperature in an internal combustion engine cylinder is introduced. The physical basis for the technique is that the flow rate through an orifice is a function of the temperature of the gas flowing through the orifice. Using a pressure transducer in the cylinder, and another in a chamber connected to the cylinder via an orifice, it is shown how the cylinder temperature can be determined with useful sensitivity. In this paper the governing equations are derived, which show that the heat transfer characteristics of the chamber are critical to the performance of the system, and that isothermal or adiabatic conditions give the optimum performance. For a typical internal combustion engine, it is found that the pre-compression cylinder temperature is related to the chamber pressure late in the compression process with sensitivity of the order of 0.005 bar/K. Copyright © 2010 SAE International.

Transport-determined early growth and development of jack mackerel Trachurus japonicus juveniles immigrating into Sagami Bay, Japan

Oceanographic conditions and transport processes are often critical factors that affect the early growth, survival and recruitment of marine fishes. Sagittal otoliths were analysed to determine age and early growth for 381 jack mackerel (Trachurus japonicus) juveniles from Sagami Bay on the Pacific coast of Japan. Two separate hatching periods ( December and February-March) were identified. They originated from the spawning grounds in the East China Sea. Early growth and developmental rates of December-hatching fish were lower than those for February-March-hatching fish. It is likely that these differences were determined in the Kuroshio Current during transport from the spawning grounds to Sagami Bay, and the lower December water temperatures in the bay. Origin and hatch dates of juveniles in Sagami Bay were in contrast to previous research on Fukawa Bay, where April-or-later-hatching fish from spawning grounds in the coastal waters of southern Japan constituted about half of the juvenile population. Management of these two jack mackerel stocks needs to consider these differences in hatch date composition and spawning origins, as these differences could affect early growth and subsequent mortality.

Studies on the energy release of rice mitochondria under different conditions by means of microcalorimetry

The thermodynamic and kinetic behaviors of energy release of mitochondria isolated from rice (Oryza sative L.) were studied by using a LKB 2277 Bioactivity Monitor under different conditions. The thermogenesis curves of energy release of the rice mitochondria (which had been kept at 0-3 degreesC for 15 h and 40 day before the determination) were determined respectively at 25 and 30 degreesC, and the difference in shape of the thermogenesis curves and thermodynamic and kinetic characteristics were compared. The thermodynamic and kinetic parameters of energy release of the mitochondria in the thermogenesis increasing stage have been calculated, and the experimental thermokinetic equations of the thermogenesis have been established. The results indicated that the lower the temperature, the slower the energy release of the rice mitochondria. Both the thermogenesis and the energy release late of the rice mitochondria increased after the mitochondria was kept at lower temperature for 40 days. One can use the methods to characterize the ability of the rice mitochondria to release energy under different conditions. (C) 2001 Published by Elsevier Science B.V.

One-dimensional modulation instability of broad optical beams in biased photorefractive-photovoltaic crystals under steady-state conditions

We present a comprehensive study of the one-dimensional modulation instability of broad optical beams in biased photo refractive-photovoltaic crystals under steady-state conditions. We obtain the one-dimensional modulation instability growth rate by globally treating the space-charge field and by considering distinction between values of Eo in nonlocal effects and local effects in the space-charge field, where Eo is the field constant correlated with terms in the space-charge field, which depends on the external bias field, the bulk photovoltaic effect, and the ratio of the optical beam's intensity to that of the dark irradiance. The one-dimensional modulation instability growth rate in local effects can be determined from that in nonlocal effects. When the bulk photovoltaic effect is neglectable, irrespective of distinction between values of Eo in nonlocal effects and local effects in the space-charge field, the one-dimensional modulation instability growth rates in nonlocal effects and local effects are those of broad optical beams studied previously in biased photorefractive-nonphotovoltaic crystals. When the external bias field is absent, the one-dimensional modulation instability growth rates in nonlocal effects and local effects predict those of broad optical beams in open- and closed-circuit photorefractive-photovoltaic crystals. (c) 2004 Elsevier B.V. All rights reserved.

Pre-irradiation with low-dose C-12(6+) beam significantly enhances the efficacy of AdCMV-p53 gene therapy in human non-small lung cancer

The combination of ionizing radiation and gene therapy has been investigated. However, there are very few reports about the combination of heavy-ion irradiation and gene therapy. To determine if the pre-exposure to low-dose heavy ion beam enhances the suppression of AdCMV-p53 on non-small lung cancer (NSLC), the cells pre-irradiated or non-irradiated were infected with 20, 40 MOI of AdCMV-p53. Survival fraction and the relative biology effect (RBE) were determined by clonogenic assay. The results showed that the proportions of p53 positive cells in C-12(6+) beam induced AdCMV-p53 infected cells were more than 90%, which were significantly more than those in gamma-ray induced AdCMV-p53 infected cells. The pre-exposure to low-dose 12C6+ beam significantly prevented the G(0)/G(1) arrest and activated G(2)/M checkpoints. The pre-exposure to C-12(6+) beam significantly improved cell to apoptosis. RBEs for the C-12(6+)+ AdCMV-p53 infection groups were 30%-60%,20% -130% and 30%-70% more than those for the C-12(6+)_irradiated only, AdCMV-p53 infected only, and gamma-irradiation induced AdCMVp53 infected groups, respectively. The data suggested that the pre-exposure to low-dose C-12(6+) beam significantly promotes exogenous p53 expression in NSLC, and the suppression of AdCMV-p53 gene therapy on NSLC.

Analysis of aromatic amines by high-performance liquid chromatography with pre-column derivatization by 2-(9-carbazole)-ethyl-chloroformate

2-(9-Carbazole)-ethyl-chloroformate (CEOC), a novel pre-column fluorescence derivatization reagent, has been developed for the analysis of aromatic amines. Taking five monocyclic aromatic amines (o-toluidine, aniline, 3,4-dimethylaniline, N-ethyl-p-toluidine, and p-phenylenediamine) as testing compounds, derivatization conditions such as pH of borate buffer, reaction time and fluorescent tagging reagent concentration have been investigated. By a one-step procedure, CEOC reacts readily with the aromatic amines to form stable derivatives with excitation and emission wavelengths, respectively, at 293 and 360 nm. This derivatization reaction could be finished within 20 min even at room temperature. The peak shapes of the derivatized aromatic amines can be improved greatly without any addition of competition amines into the mobile phase. Furthermore, this method can offer excellent quantitative precision with high tolerance of the matrix of samples. (C) 2003 Elsevier B.V. All rights reserved.

Preparation and Characterization of Melt Grafting 2-acrylamido-2-methyl-1-propanesulfonic Acid onto Pre-Irradiated Linear Low Density Polyethylene

Linear low density polyethylene (LLDPE) was functionalized with 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) by using -ray pre-irradiation in air in a twin-screw extruder. Fourier-transformed infrared spectroscopy (FT-IR) and electron spectroscopy for chemical analysis (ESCA) were used to characterize the formation of LLDPE-g-AMPS copolymers. The content of AMPS in LLDPE-g-AMPS was determined by using element analysis instrument. The effects of concentrations of monomer, reaction temperature and pre-irradiation dose on degree of grafting were investigated. The critical surface tension of LLDPE-g-AMPS was measured by using contact angle method. The influences of the degree of grafting on crystallization properties were studied by using DSC. Compared with neat LLDPE, the crystallization temperature increased about 4C, and crystallinity decreased with increasing degree of grafting. Crystallization rates of grafted LLDPE were faster than that of plain LLDPE at the same crystallization temperature.

Chandrananimycins A-C: Production of novel anticancer antibiotics from a marine Actinomadura sp isolate M048 by variation of medium composition and growth conditions

In our screening of marine actinomycetes for bioactive principles, three novel antibiotics designated as chandrananimycin A (3c), B (3d) and C (4) were isolated from the culture broth of a marine Actinomadura sp. isolate M045. The structures of the new antibiotics were determined by detailed interpretation of mass, 1 D and 2 D NMR spectra.

Formation and early development of tetraspores of Gracilaria lemaneiformis (Gracilaria, Gracilariaceae) under laboratory conditions

Morphological and culture studies of tetraspores of Gracilaria lemaneiformis were carried out under laboratory conditions. Relationships of germination rate, diameter and survival rate of tetraspores from 1st generation branches with grads of temperature and irradiance were determined, respectively. The result showed that 1st generation branches is in the majority of the tetraspores shedding and tetraspores from which had highest survival rates than other parts of the sporophytic plant. The time tetraspores used developing from giant unicells to diads, which both existed on the epidermis, then to tetraspores off the matrix, was only approximately 3 weeks all through. However, tetraspores spent more than two months developing into germlings of gametophytes. It was shown that temperature variation (10, 15, 25, 30 degrees C) with the light of 30 mu mol m(-2) s(-1) had significant effects on the germination rate and diameter, but had no apparent effect on survival rate (ANOVA, P < 0.01). Germination rates of tetraspores reached the maximum at 20 degrees C, which was significantly higher than those at other temperature levels (P < 0.01), whereas 15 degrees C seemed to be optimal temperature for the diameter. All the three growth parameters (germination rate, diameter and survival rate) yield highly significant variations with irradiance treatments at room temperature (ANOVA, P < 0.01). The optimal germination rate was detected at the irradiance of 30 mu mol m(-2) s(-1) (P < 0.01). The photon flux density which exceeds 480 nnol m(-2) s(-1) have apparently negative effect on diameter and survival rate. (c) 2005 Elsevier B.V. All rights reserved.

Determination of aliphatic amines from soil and wastewater of a paper mill by pre-column derivatization using HPLC and tandem mass spectrometry (HPLC-MS/MS)

A pre-column derivatization method for the sensitive determination of aliphatic amines using the labeling reagent 1,2-benzo-3,4-dihydrocarbazole-9-ethyl chloroformate (BCEOC) followed by HPLC with fluorescence detection and APCI/NIS identification in positive-ion mode has been developed. The chromophore of 2-(9-carbazole)-ethyl chloroformate (CEOC) reagent was replaced by the 1,2-benzo-3,4-dihydrocarbazole functional group, which resulted in a sensitive fluorescence derivatizing reagent, BCEOC, that could easily and quickly label amines. Derivatives were stable enough to be efficiently analyzed by HPLC and showed an intense protonated molecular ion corresponding m/z [M + H](+) with APCI/MS in positive-ion mode. The collision induced dissociation of the protonated molecular ion formed characteristic fragment ions at m/z 264.1, m/z 246.0 and m/z 218.1, corresponding to the cleavages of CH2CH2O-CO, CH2CH2-OCO, and N-CH2CH2O bonds. Studies on derivatization conditions demonstrated that excellent derivatization yields close to 100% were observed with a 3 to 4-fold molar reagent excess in acetonitrile solvent, in the presence of borate buffer (pH 9.0) at 40 degrees C for 10 min. In addition, the detection responses for BCEOC derivatives were compared with those obtained with CEOC and FMOC as labeling reagents. The ratios I-BCEOC/I-CEOC and I-BCEOC/I-FMOC were, respectively, 1.40-2.76 and 1.36-2.92 for fluorescence responses (here, I was the relative fluorescence intensity). Separation of the amine derivatives had been optimized on an Eclipse XDB-C-8 column. Detection limits calculated from an 0.10 pmol injection, at a signal-to-noise ratio of 3, were 18.65-38.82 fmol (injection volume 10 mu L for fluorescence detection. The relative standard deviations for intraday determination (n = 6) of standard amine derivatives (50 pmol) were 0.0063-0.037% for retention times and 3.36-6.93% for peak areas. The mean intra-and inter-assay precision for all amines were <5.4% and 5.8%, respectively. The recoveries of amines ranged from 96 to 113%. Excellent linear responses were observed with correlation coefficients of >0.9994. The established method provided a simple and highly sensitive technique for the quantitative analysis of trace amounts of aliphatic amines from biological and natural environmental samples.

柴达木盆地地震勘探关键技术研究

The rugged surface topography determined the seismic data acquisition construction conditions and the seismic wave explosive and receiver quality in Qaidam Basin. This dissertation systematically researched the seismic acquisition, imaging process and the attribute analysis techniques of complicated oil and gas reservoir. The main research achievements and cognitions are as follows: 1. Through the stimulation effects research and analysis from the aspect of lithologic water-containing differences, it’s specific that stable hydrous sand layer can effectively enhance the stimulation effects combined with the corresponding field tests. The seismic data S/N ratio has been improved due to the combination explosive stimulation. Through the fold number and maximum offset analyses of target horizon, the complicated geometry has been optimized and the S/N ratio of seismic data has been improved, which made an important basis for improvement of 3D seismic data. 2. It has been proved that the first arrival refraction static correction method under the model constraint of fine surface survey is suitable to the Qaidam Basin of western areas by the real seismic data processing. Although the refraction horizon of near surface has some changes in a certain extent, it’s steady basically. The refraction horizon can be continuously traced in sections, so it’s qualified for the refraction static correction method on the whole. 3. The research is based on the curved-ray pre-stack time migration techniques of rough topography, and improved the imaging precision of complex areas. This techniques adopted the constant and variable velocity scanning mode and enhanced the velocity analysis precision. The 3D pre-stack time migration techniques reasonably solved the imaging and velocity multiple solutions problems of steep-dip faults and the intersections of horizontal layers. What’s more, fine velocity analysis and mute are very important to enhance the imaging precision of the seismic data in complicated Wunan areas. 4. The 3D seismic data edge-preserving processing methods have been realized due to the image process techniques. Because this method uses the large range filter, it can attenuate the noise maximally. The faults, break points, lithologic pinchout points and lithologic body of small scale such as river will not be influenced by blur because of the edge-preserving characterization of the method which is really an effective assistant technique of low S/N ratio seismic data attribute analysis. 5. The use of spectral decomposition technique can effectively identify the reservoirs. The special geology body which will not be identified (or without obvious characters) in the seismic profile may be found through the details changes of different frequencies in the amplitude profiles.

济阳地区深部结构与含油气性讨论

Oil and gas exploration of marine strata in China's Pre-Cenozoic residual basins is regarded as a worldwide puzzle because of existent problems and cruxes. Objectively speaking, the subsurface geologic structure is complicated, and the surface conditions of some areas are tough. On the other hand, there are still many problems to be solved in oil and gas exploration technologies of Pre-Cenozoic marine fades, and theoretic cognition about petroleum geology is not profound yet. Therefore, it is principal to explore integrated geophysical research ways of Pre-Cenozoic residual basins. Seismic prospecting and geophysical integrated interpretation technologies aimed at middle Paleozoic marine facies with deeper burial and complicated geologic conditions have not formed due to bad quality of deep strata data. Pre-Cenozoic strata, and especially extension, thickness and internal structure of Paleozoic strata can not be recognized from seismic profiles, so it is hard to systematically cognize structural features and oil-gas resources prospect of Pre-Cenozoic basins. To further investigation of fabric and structural features, basin prototype, formation and evolution pattern of Pre-Cenozoic basins, and also their control over formation, migration and aggregation of oil and gas, will play a guiding and promotive role in developing new surveying areas, selecting advantageous zones and predicting oil-gas resources.This paper follows the modem macrocontrol theory of "Region constrains local, deep strata controls shallow ones", and uses the integrated geophysical method of "One guide, two hinges, three combinations and multi feedbacks'*. Based on several years of geological and geophysical results of the Shengli Oilfield, and 14 newly-joint regional seismic profiles, deep structure and oil-gas bearing capacity of the Jiyang area are discussed and new cognitions are drawn as below.Seismic identification marks Tr, Tg, Tgl and Tg2 are established for importantPre-Cenozoic geological interfaces, and promoted to the whole Jiyang area.Through area-wide tracking and clogging of important seismic reflection marker,the isochronic framework of pre-Tertiary basin is set up in the Jiyang area for the firsttime, which is vital for basin research.Integrated with geological and geophysical research results, the Jiyang area isdivided into four first-order tectonic sequences- basement, lower tectonic layer,upper tectonic layer, and top tectonic layer. The basement and lower tectonic sequence which are related to Pre-Cenozoic are studied with emphasis.Through the research of regional seismic profiles, the point of view is given thatthe Kongdian Formation of Jiyang is structural transition period. The top-bottomunconformable interface of the Kongdian Formation is found out for the first time,and the basin model is determined primarily, which lay a basis for prototype basinresearch of the Jiyang Kongdian Formation.The distribution status of Middle-Paleozoic is delineated in the Jiyang area.The maximum thickness of Paleozoic lies in the top of the south declivity of half-graben. The thickness gets thinner towards the center of Mesozoic and Cenozoic half-graben basin, and even disappears. Structural action in the west-north affects the distribution of Paleozoic residual strata.6. The features of second-order tectonic sequence of the Jiyang depression isstudied and its evolution history of is rebuilt.Combined with the 5-stage evolution history of the China continent and structure evolution features of the Jiyang area, the structure sedimentary process since Paleozoic is divided into 5 periods - basement forming , Indosinian orogenic, Yanshan negative reversal, Himalayan extension and Neogene subsidence period.Combined with the research results of gravity, magnetic surveying and regionalprofiles, this paper brings forward the idea for the first time that the western boundaryof the Jiyang depression is the Ningjin-Yangpan fracture zone, and forms aside-column assemblage with the Wudi fracture zone.The opinion that under Middle-Cenozoic basins in the middle Jiyang area theremight superimpose an old residual basin is given for the first time. And if it is provedto be true, a new exploration space will be pioneered for Jiyang and even north China.There exists many types of tectonic-stratigraphic traps formed under piezotropy,extension and compound action in Pre-Cenozoic Jiyang. Therein all kinds of burialhills are the most important oil-gas trap type of Pre-Cenozoic, which should besurveyed layeredly according to the layout of oil sources.As such a new challenging project and field, the paper systematically analyses different geophysical responses of the Jiyang area, frames the deep structure of the area, and preliminarily recognizes the Pre-Cenozoic residual basins. It breaks through to a certain extent in both theory and practice, and is expected to provide new geophysical and geotectonic clues for deep exploration in Shengli.

Determination of alcohols by high-performance liquid chromatography with fluorimetric detection after pre-column derivatisation with carbazole-9-N-acetic acid and chromatographic behaviour of alcoholic derivatives

Alcohols were derivatised to their carbazole-9-N-acetic acid (CRA) esters with 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride (EDC . HCl) as the dehydrating agent. Studies on derivatisation conditions indicated that the coupling reaction proceeded rapidly and smoothly in the presence of a base catalyst in acetonitrile to give the corresponding sensitively fluorescent derivatives. The retention behaviour of alcohol derivatives was investigated by varying mobile phase compositions (ACN-water and MeOH-water). The parameters from the equation log k'=A-BX were evaluated by retention data of derivatives using an isocratic elution with different mobile phases. The results indicated that the parameters derived allowed computation of retention factors in good agreement with experiments. At the same time, a general equation was derived that makes possible predictions of partition coefficient in binary mobile phases with different proportions of organic solvent to water based on some simple regression analysis. The LC separation for the derivatised alcohols containing higher carbon alcohols showed good reproducibility on a reversed-phase C-18 column with gradient elution. The detection limits (excitation at 335 nm, emission at 360 nm) for derivatised alcohols (signal-to-noise ratio=3:1) were in the range of 0.1-0.4 pg per injection. (C) 2001 Elsevier Science B.V. All rights reserved.