Effect of light-curing method and indirect veneering materials on the Knoop hardness of a resin cement

This study evaluated the Knoop hardness of a dual-cured resin cement (Rely-X ARC) activated solely by chemical reaction (control group) or by chemical / physical mode, light-cured through a 1.5 mm thick ceramic (HeraCeram) or composite (Artglass) disc. Light curing was carried out using conventional halogen light (XL2500) for 40 s (QTH); light emitting diodes (Ultrablue Is) for 40 s (LED); and Xenon plasma arc (Apollo 95E) for 3 s (PAC). Bovine incisors had their buccal face flattened and hybridized. On this surface a rubber mold (5 mm in diameter and 1 mm in height) was bulk filled with the resin cement. A polyester strip was seated for direct light curing or through the discs of veneering materials. After dry storage in the dark (24 h 37°C), the samples (n = 5) were sectioned for hardness (KHN) measurements, taken in a microhardness tester (50 gF load 15 s). The data were statistically analyzed by ANOVA and Tukey's test (α = 0.05). The cement presented higher Knoop hardness values with Artglass for QTH and LED, compared to HeraCeram. The control group and the PAC/Artglass group showed lower hardness values compared to the groups light-cured with QTH and LED. PAC/HeraCeram resulted in the worst combination for cement hardness values. © 2009 Sociedade Brasileira de Pesquisa Odontológica.

Hybridization effect on the mechanical properties of curaua/glass fiber composites

The aim of this paper was to evaluate the effect of hybridizing glass and curaua fibers on the mechanical properties of their composites. These composites were produced by hot compression molding, with distinct overall fiber volume fraction, being either pure curaua fiber, pure glass fiber or hybrid. The mechanical characterization was performed by tensile, flexural, short beam, Iosipescu and also nondestructive testing. From the obtained results, it was observed that the tensile strength and modulus increased with glass fiber incorporation and for higher overall fiber volume fraction (%Vf). The short beam strength increased up to %Vf of 30 vol.%, evidencing a maximum in terms of overall fiber/matrix interface and composite quality. Hybridization has been successfully applied to vegetable/synthetic fiber reinforced polyester composites in a way that the various properties responded satisfactorily to the incorporation of a third component. © 2013 Published by Elsevier Ltd. All rights reserved.

Avaliação das propriedades térmicas, químicas e mecânica relacionando dente bovino e dente humano

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação comparativa in vitro da rugosidade superficial de resinas compostas submetidas a diferentes técnicas de polimento

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da distância de uma fonte de luz halógena na microdureza superficial da resina composta

Pós-graduação em Ciências Odontológicas - FOAR

Quantificação do ar incluído e espectro de gotas de pontas de pulverização em aplicações com adjuvantes

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Metodologia para implantação e controle de coleta seletiva de resíduos sólidos industriais recicláveis

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Aproveitamento dos resíduos de compósitos à base de resina poliéster e fibra de vidro

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Biodegradação de filmes de PVC e PCL por fungos filamentosos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Blendas de PVC/PCL foto/termo e biotratadas com fungos de solo (Phanerochaete chrysosporium e Aspergillus fumigatus)

Pós-graduação em Ciências Biológicas (Microbiologia Aplicada) - IBRC

Esterilização de pontas diamantadas através da energia por microondas

Pós-graduação em Reabilitação Oral - FOAR

Modificação superficial de fibras de juta com descarga corona para melhora da aderência com matriz poliéster

Seeking alternatives for the total or partial substitution of synthetic fibers for natural fibers, with reinforcement in polymeric materials, this work was conducted with the objective of evaluating the treatment with corona discharge on the adherence of juta fibers with resin. The fibers were exposed to corona discharge for 1, 5, 10 and 15 minutes, as well as after treatment with hot water, molding composites fiber-reinforced with filaments treated for 10 and 15 minutes, and without the treatment. The chemical structures were evaluated by spectrometry in the region of Fourier transform infrared with attenuated total reflection (FTIR/ATR), observing the formation of a new band and the increase in the absorption of groupings with oxygen. The thermal analyses, such as thermogravimetry (TG) and differential scanning calorimetry (DSC) revealed the degradation of cellulose, hemicellulose and lignin. The microstructural characterization by scanning electron microscopy (SEM) showed changes in the surface of the fiber, such as roughness, superficial depressions, surface degradation and cavity formation. The adhesion of the fibers was evaluated by the pullout test, allowing us to verify the increase in adhesion strength after treatment with corona discharge. In conclusion, the treatment with corona discharge changes the surface of the juta fibers, resulting in better adherence with the resin.

Desenvolvimento de um método de análise por injeção em fluxo (FIA) para determinação de dissulfeto de tetrametiltiuram (tiram) utilizando reagente imobilizado em reator de fase sólida (RFS)

Pós-graduação em Química - IBILCE

Estudos fisiológicos e moleculares durante a superação da dormência morfológica de sementes de Annona crassiflora

Pós-graduação em Agronomia (Agricultura) - FCA

Desenvolvimento e avaliação da efetividade de duas pastas polidoras em padrão nanométrico empregadas a materiais restauradores estéticos: análise comparativa por perfilometria digital e microscopia de força atômica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)