Properties of glass-ceramics obtained from crystallization of the SiO2-Al2O3-MgO-Li2O system with addition of ZrO2

This paper presents the study results with glass-ceramics obtained from base glass (MgO-Al2O3- SiO2-Li2O system) with addition of ZrO2 as nucleating agent. The glass was melted at 1650 degrees C for 3 h and at a heating rate of 10 degrees C/min. The molten glass was poured into a graphite mold to obtain monolithic samples and also in water in order to obtain particulate material. Such material was grinded and then pressed by both uniaxial and isostatic pressing methods before being sintered. Both the monolithic and pressed samples were performed under two different conditions of heat treatment so that their nucleation and crystallization occurred. In the first one, the samples were heated to 1100 degrees C with a heating rate of 10 degrees C/min. In the second one, there was an initial heating rate of 10 degrees C/min up to 780 degrees C, which was kept for 5 minutes. After that, the samples were heated to 1100 degrees C at a heating rate of 1 degrees C/min. Microhardness analyses showed that base glass presented values around 7.0 GPa. The glass-ceramics obtained from the powder sintering showed microhardness values lower than those obtained from monolithic samples. The highest hardness values were observed in the samples which were treated with two heating rates, whose values were around 9.2 +/- 0.5 GPa. Moreover, the glass-ceramics which were produced with an only heating rate, presented values around 7.1 +/- 0.2 GPa, very close to those observed in the base glass.

A comparison of microhardness of indirect composite restorative materials

The purpose of this study was to compare the microhardness of four indirect composite resins. Forty cylindrical samples were prepared according to the manufacturer s recommendations using a Teflon mold. Ten specimens were produced from each tested material, constituting four groups (n=10) as follows: G1 - Artglass; G2 - Sinfony; G3 - Solidex; G4 - Targis. Microhardness was determined by the Vickers indentation technique with a load of 300g for 10 seconds. Four indentations were made on each sample, determining the mean microhardness values for each specimen. Descriptive statistics data for the experimental conditions were: G1 - Artglass (mean ±standard deviation: 55.26 ± 1.15HVN; median: 52.6); G2 - Sinfony (31.22 ± 0.65HVN; 31.30); G3 - Solidex (52.25 ± 1.55HVN; 52.60); G4 - Targis (72.14 ± 2.82HVN; 73.30). An exploratory data analysis was performed to determine the most appropriate statistical test through: (I) Levene's for homogeneity of variances; (II) ANOVA on ranks (Kruskal-Wallis); (III) Dunn's multiple comparison test (0.05). Targis presented the highest microhardness values while Sinfony presented the lowest. Artglass and Solidex were found as intermediate materials. These results indicate that distinct mechanical properties may be observed at specific materials. The composition of each material as well as variations on polymerization methods are possibly responsibles for the difference found in microhardness. Therefore, indirect composite resin materials that guarantee both good esthetics and adequate mechanical properties may be considered as substitutes of natural teeth.

Adesivos multi-uso-avaliação da resistência adesiva a dentina frente a teste de cisalhamento, estereomicroscopia e microscopia eletrônica de varredura

Recent bonding systems have been advocated as multi-purpose bonding agents. The aim of this study was to determine if some of these bonding systems could be associated to composite resins from different manufacturers. This investigation was conducted to test lhe shear bond strength of three bonding systems: Scotchbond Multi-Purpose (3M Dental Products), Optibond Light Cure (Kerr) and Optibond Dual Cure (Kerr), when each of them was associated to lhe composite resins: Z1 00 (3M Dental Products), Prisma - APH (Dentsply) and Herculite XRV (Kerr). Seventy-two flat dentin bonding sites were prepared to 600 grit on human premolars mounted using acrilic resins. The teeth were assigned at random to 9 groups of 8 samples each. A split die with a 3mm diameter was placed over lhe surface of lhe dentin treated with one of lhe adhesive systems, and lhe selected composite resin was inserted and light cured. The split mold was removed and all samples were termocycled and stored in 37ºC water for 24 hours before testing. Shear bond strength was determined using an lnstron Universal testing machine. Some failures were examined under lhe S.E.M. Data was analysed by one-way analysis of variance, that demonstrated a significant difference (p<0,05) in the mean shear bond strength among Optibond Light Cure (15,446 MPa), Scotchbond Multi-Purpose (13,339 MPa) and Optibond Dual Cure (10,019 MPa). These values did not depend on the composite resin used. The association between bonding system/composite resin was statistycally significant (p<0,05) and the best results were obtained when the composite resins Z100 and Herculite were used with the adhesive system Optibond Light Cure, and when the composite resin APH was used with the adhesive system Scotchbond Multi-Purpose

O processo constitutivo da Resolução de Problemas como uma temática da pesquisa em Educação Matemática: um inventário a partir de documentos dos ICMEs

Pós-graduação em Educação Matemática - IGCE

Effect of polymerization techniques and cleaning solution on flexural resistance of acrylic resin chemically activated

The purpose of this study was to evaluate the impact of different disinfection solutions on flexural resistance of chemically-activated acrylic resin. Test pieces were made of clear acrylic resin using a rectangular mold and employing two techniques: wet polymerization under pressure (n = 20) and dry polymerization under pressure (n = 20). Test pieces were subdivided into four equal groups: distilled water (control), sodium bicarbonate, 1% sodium hypochlorite and effervescent ats. The 30-day cycling technique consisted of immersing the test pieces in 100 ml of solution for 10 min three times a day and placing them in closed containers containing artificial saliva at 37°C. Subsequently, the flexural resistance of samples was tested. Data were analyzed using two-way analysis of variance (ANOVA) with forces serving as the dependent variables and the polymerization technique and cleaning agents as independent variables. Post hoc multiple comparisons were performed using Tukey’s test. There was no statistically significant difference in the flexural strength between the two polymerization techniques. The greatest flexural strength was observed for the effervescent tablets group followed by the control and 1% sodium hypochlorite groups which were statistically similar. Thus, the sodium bicarbonate solution caused the lowest flexural resistance of the test pieces.

Métodos de aplicação e de avaliação do residual de fungicidas no controle de mofo-branco em soja e feijão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Difusão de tecnologia CAD e CNC como ferramenta básica de criação e produção em pequena escala, acessível à comunidade

The high competitiveness and the search for newtechnologies that differentiate the product from the project,require the use of new digital tools. The computer aideddesign - Computed Aided Design (CAD), with electronicmodeling, simulation, structural analysis and production,performed in a virtual environment through the applicationof specific software, are available but their use is stilllimited. There are various software available in languagesand extensions to industrial production which, from 3Dmodeling, they can manage through Computer NumericalControl - Computed Numerical Control (CNC) machiningcenters, laminating, stamping, mold making and otherprocesses productive. This project aims to encouragecreativity and entrepreneurship in the community throughthe provision of technology computer aided design - CAD,with a view to implementation of machining technology.

O naturalismo como técnica de representação realista: uma proposta teórico-crítica para BaléRalé, de Marcelino Freire

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resistência de união de cimentos resinosos, convencional e autoadesivo, em substratos dentinários normal e hipermineralizado artificalmente

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação microbiológica e sensorial do guacamole conservado pelo frio

Avocado (Persea americana Mill.) is a product grown in tropical and subtropical regions and from it we can extract products like guacamole which is highly consumed in the Mexican culinary. The most used varieties for guacamole are the Hass and Fuerte. The present research had as objective to evaluate the microbiological and sensorial quality of the guacamole conserved through cold with no addition of additives. The microbiological analyses have shown the product reached satisfactory results as for the analysis of total and thermoenduring coliform < 3,0 UFC/g, Salmonella absent in 25g, Staphylococcus aureus and Bacillus cereus < 100 UFC/g, presenting values within the patterns set by RDC of Anvisa 12 of January 2nd 2001. The analyses of mesophile bacteria and the counting of mold and yeast reached values between 102 and 104 UFC/g and the psychrotropic bactéria presented values < 100 UFC/g. The sensorial anlyses have shown that the polyethylene package isn't effective in keeping the analysed sensorial parameters. Although the polyethylene and nylon packages had better results, however they didn't differentiate themselves so as the vacuum use.

Effects of UV-B radiation on the antagonistic ability of Clonostachys rosea to Botrytis cinerea on strawberry leaf disc

Human activities are altering the concentrations of ozone in the troposphere and hence in the incidence of ultraviolet-B (UV-B) on Earth’s surface. Although representing only five percent of UV-B radiation striking the Earth's surface, this radiation has the potential to cause effects on biologically active molecules. Sensitivity to UV-B radiation is one of the limitations of biological control of plant pathogens in the field. The objectives of this work were to evaluate the effects of UV-B on several isolates of Clonostachys rosea, and the ability of an isolate of C. rosea, previously selected for its tolerant to UV-B radiation, to control Botrytis cinerea on strawberry leaves in controlled conditions (strawberry leaf discs). The germination of C. rosea conidia was inversely proportional to the irradiance. The most tolerant strain (LQC62) had relative germination of about 60% after irradiation of 4.2kJ/m2, and this strain was selected to be used in the subsequent studies. The data showed that even with exposure to UV-B radiation, C. rosea LQC62 controlled the pathogen. Conidial concentrations of strain LQC62 above 105 conidia/ml showed higher tolerance to UV-B radiation and increased ability to control more than 75% of the B. cinerea even with exposure to radiation. According to our results, in addition to showing less growth under UV-B, conidia of C. rosea had lower antagonistic ability. Further studies are needed to observe the tolerance of B. cinerea conidia to UV-B radiation and thereby prove that an environment with increased UV-B radiation may be favoring the pathogen due to a lower ability of C. rosea to control the pathogen in conditions of increased UV-B.

Strains of Coniothyrium minitans reduce the emission of apothecia of Sclerotinia sclerotiorum

Sclerotia of Sclerotinia sclerotiorum (Ss) can survive for long time in soil and are the main inoculum source of the white mold disease. An alternative for reducing this inoculum is the use of parasites, such as Coniothyrium minitans (Cm). We evaluated the potential of Cm isolates for the biological control of Ss in beans. The effect of the temperature on the growth of 15 isolated of Cm was evaluated in vitro. The hyperparasitism ability of Cm was evaluated in soil infested with sclerotia and conditioned in pots. The infested soil was treated with conidia suspension of the antagonists, fluazinan or sterile distilled water. After seven days at 20°C, the sclerotia were removed from soil and placed inside Petri dishes over bean leaves previously disinfested. The germination and parasitism of sclerotia were evaluated after 7 to 10 days. To evaluate the apothecia emission, soil infested with sclerotia of Ss and treated as described was maintained at 18°C and the number of emerged apothecia was counted up to 84 days after inoculation. The emergence of bean plants in soil infested with sclerotia and mycelium of the pathogen and treated as described was evaluated in greenhouse. The ideal temperature for growth of Cm isolates varied from 18 to 19°C and at 30-35°C they were complete inhibited. The isolates of Cm promoted less than 10% of reduction in viability of the sclerotia, but they significantly reduced the emission of apothecia. Two isolates increased the emergence of plants in relation to the inoculated check, but was significantly lower than the non-inoculated check. Field tests will be conduct to confirm the potential of the selected isolates to reduce the inoculum source of the pathogen.

Desenvolvimento e avaliação de um sistema de liberação sustentada de gentamicina em biomembranas de látex natural

Pós-graduação em Biociências - FCLAS

Micotoxinas estrogênicas em águas superficiais da microbacia hidrográfica do Córrego Rico (SP): desenvolvimento de método analítico verde, ocorrência e persistência ambiental

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

MATERIAL MODELING AND ANALYSIS FOR THE DEVELOPMENT OF A REALISTIC BLAST HEADFORM

Blast traumatic brain injury (BTBI) has become an important topic of study because of the increase of such incidents, especially due to the recent growth of improvised explosive devices (IEDs). This thesis discusses a project in which laboratory testing of BTBI was made possible by performing blast loading on experimental models simulating the human head. Three versions of experimental models were prepared – one having a simple geometry and the other two having geometry similar to a human head. For developing the head models, three important parts of the head were considered for material modeling and analysis – the skin, skull and brain. The materials simulating skin, skull and brain went through many testing procedures including dynamic mechanical analysis (DMA). For finding a suitable brain simulant, several materials were tested under low and high frequencies. Step response analysis, rheometry and DMA tests were performed on materials such as water based gels, oil based mixtures and silicone gels cured at different temperatures. The gelatins and silicone gels showed promising results toward their use as brain surrogate materials. Temperature degradation tests were performed on gelatins, indicating the fast degradation of gelatins at room temperature. Silicone gels were much more stable compared to the water based gels. Silicone gels were further processed using a thinner-type additive gel to bring the dynamic modulus values closer to those of human brain matter. The obtained values from DMA were compared to the values for human brain as found in literature. Then a silicone rubber brain mold was prepared to give the brain model accurate geometry. All the components were put together to make the entire head model. A steel mount was prepared to attach the head for testing at the end of the shock tube. Instrumentation was implemented in the head model to obtain effective results for understanding more about the possible mechanisms of BTBI. The final head model was named the Realistic Explosive Dummy Head or the “RED Head.” The RED Head offered potential for realistic experimental testing in blast loading conditions by virtue of its material properties and geometrical accuracy.