A comparative study of energy transfer in dye mixtures in monomer and polymer matrices under pulsed laser excitation

This study was conducted to identify the concentration dependence of the operating wavelengths and the relative intensities in which a dye mixture doped polymer optical fibre can operate. A comparative study of the radiative and Forster type energy transfer processes in Coumarin 540:Rhodamine 6G, Coumarin 540:Rhodamine B and Rhodamine 6G:Rhodamine B in methyl methacrylate (MMA) and poly(methyl methacrylate) (PMMA) was done by fabricating a series of dye mixture doped polymer rods which have two emission peaks with varying relative intensities. These rods can be used as preforms for the fabrication of polymer optical fibre amplifiers operating in the multi-wavelength regime. The 445 nm line from an Nd:YAG pumped optical parametric oscillator (OPO) was used as the excitation source for the first two dye pairs and a frequency doubled Nd:YAG laser emitting at 532 nm was used to excite the Rh 6G:Rh B pair. The fluorescence lifetimes of the donor molecule in pure form as well as in the mixtures were experimentally measured in both monomer and polymer matrices by time-correlated single photon counting technique. The energy transfer rate constants and transfer efficiencies were calculated and their dependence on the acceptor concentration was analysed. It was found that radiative energy transfer mechanisms are more efficient in all the three dye pairs in liquid and solid matrices.

Cavitation in 3He-4He liquid mixtures at low temperatures

Bubble formation in solutions of 3He and 4He is studied within a density-functional approach. In particular, the temperature dependence of the cavitation pressure for different 3He concentrations is calculated at low temperatures and compared to that of pure 4He. The presence of Andreev states lowers the surface tension and, consequently, nucleation barriers are drastically reduced. This fact means that even at low 3He concentrations the cavitation process takes place at higher pressures than the spinodal pressure, which is not the case for pure 4He.

Influence Of Additives On The Drain Down Characteristics Of Stone Matrix Asphalt Mixtures

In Kerala highways, where traditional dense graded mixtures are used for the surface courses, major distress is due to moisture induced damages. Development of stabilized Stone Matrix Asphalt (SMA) mixtures for improved pavement performance has been the focus of research all over the world for the past few decades. Many successful attempts are made to stabilize SMA mixtures with synthetic fibres and polymers. India, being an agricultural economy produces fairly huge quantity of natural fibres such as coconut, sisal, banana, sugar cane, jute etc.. Now- a -days the disposal of waste plastics is a major concern for an eco- friendly sustainable environment. This paper focuses on the influence of additives like coir, sisal, banana fibres (natural fibres), waste plastics (waste material) and polypropylene (polymer) on the drain down characteristics of SMA mixtures. A preliminary investigation is conducted to characterize the materials used in this study. Drain down sensitivity tests are conducted to study the bleeding phenomena and drain down of SMA mixtures. Based on the drain down characteristics of the various stabilized mixtures it is inferred that the optimum fibre content is 0.3% by weight of mixture for all fibre mixtures irrespective of the type of fibre. For waste plastics and polypropylene stabilized SMA mixtures, the optimum additive contents are respectively 7% and 5% by weight of mixture. Due to the absorptive nature of fibres, fibre stabilizers are found to be more effective in reducing the drain down of the SMA mixture. The drain values for the waste plastics mix is within the required specification range. The coir fibre additive is the best among the fibres investigated. Sisal and banana fibre mixtures showed almost the same characteristics on stabilization.

Classification of recycled sands and their applications as fine aggregates for concrete and bituminous mixtures

As a result of the drive towards waste-poor world and reserving the non-renewable materials, recycling the construction and demolition materials become very essential. Now reuse of the recycled concrete aggregate more than 4 mm in producing new concrete is allowed but with natural sand a fine aggregate while. While the sand portion that represent about 30\% to 60\% of the crushed demolition materials is disposed off. To perform this research, recycled concrete sand was produced in the laboratory while nine recycled sands produced from construction and demolitions materials and two sands from natural crushed limestone were delivered from three plants. Ten concrete mix designs representing the concrete exposition classes XC1, XC2, XF3 and XF4 according to European standard EN 206 were produced with partial and full replacement of natural sand by the different recycled sands. Bituminous mixtures achieving the requirements of base courses according to Germany standards and both base and binder courses according to Egyptian standards were produced with the recycled sands as a substitution to the natural sands. The mechanical properties and durability of concrete produced with the different recycled sands were investigated and analyzed. Also the volumetric analysis and Marshall test were performed hot bituminous mixtures produced with the recycled sands. According to the effect of replacement the natural sand by the different recycled sands on the concrete compressive strength and durability, the recycled sands were classified into three groups. The maximum allowable recycled sand that can be used in the different concrete exposition class was determined for each group. For the asphalt concrete mixes all the investigated recycled sands can be used in mixes for base and binder courses up to 21\% of the total aggregate mass.

Urban Grass and Grass-Leaf Litter Mixtures as Source for Bioenergy Recovery

Städtische Biomassen der Grünflächen bilden eine potentielle, bisher weitgehend ungenutzte Ressource für Bioenergie. Kommunen pflegen die Grünflächen, lassen das Material aber verrotten oder führen es Deponien oder Müllverbrennungsanlagen zu. Diese Praxis ist kostenintensiv ohne für die Verwaltungen finanziellen Ausgleich bereitzustellen. Stattdessen könnte das Material energetisch verwertet werden. Zwei mögliche Techniken, um Bioenergie zu gewinnen, wurden mit krautigem Material des städtischen Straßenbegleitgrüns untersucht i) direkte anaerobe Fermentation (4 Schnitte im Jahr) und ii) „Integrierte Festbrennstoff- und Biogasproduktion aus Biomasse“ (IFBB), die Biomasse durch Maischen und mechanisches Entwässern in einen Presssaft und einen Presskuchen trennt (2 Schnitte im Jahr). Als Referenz wurde die aktuelle Pflege ohne Verwertungsoption mitgeführt (8faches Mulchen). Zusätzlich wurde die Eignung von Gras-Laub-Mischungen im IFBB-Verfahren untersucht. Der mittlere Biomasseertrag war 3.24, 3.33 und 5.68 t Trockenmasse ha-1 jeweils für die Pflegeintensitäten Mulchen, 4-Schnitt- und 2-Schnittnutzung. Obwohl die Faserkonzentration in der Biomasse der 2-Schnittnutzung höher war als im Material der 4-Schnittnutzung, unterschieden sich die Methanausbeuten nicht signifikant. Der Presskuchen aus dem krautigen Material des Straßenbegleitgrüns hatte einen Heizwert von 16 MJ kg-1 Trockenmasse, während der Heizwert des Presskuchens der Gras-Laub-Mischung in Abhängigkeit vom Aschegehalt zwischen 15 und 17 MJ kg-1 Trockenmasse lag. Der Aschegehalt der Mischungen war höher als der Grenzwert nach DIN EN 14961-6:2012 (für nicht-holzige Brennstoffe), was auf erhöhte Bodenanhaftung auf Grund der Erntemethoden zurückzuführen sein könnte. Der Aschegehalt des krautigen Materials vom Straßenrand hielt die Norm jedoch ein. Die Elementkonzentration (Ca, Cl, K, Mg, N, Na, P, S, Al, Cd, Cr, Cu, Mn, Pb, Si, Zn) im krautigen Material war generell ähnlich zu Landwirtschafts- oder Naturschutzgrünland. In den Mischungen nahm die Elementkonzentration (Al, Cl, K, N, Na, P, S, Si) mit zunehmendem Laubanteil ab. Die Konzentration von Ca, Mg und der Neutral-Detergenz-Fasern stieg hingegen an. Die IFBB-Technik reduzierte die Konzentrationen der in der Verbrennung besonders schädlichen Elemente Cl, K und N zuverlässig. Außer den potentiell hohen Aschegehalten, wurde während der Untersuchungen kein technischer Grund entdeckt, der einer energetischen Verwertung des getesteten urbanen Materials entgegenstehen würde. Ökonomische, soziale und ökologische Auswirkungen einer Umsetzung müssen beachtet werden. Eine oberflächliche Betrachtung auf Basis des bisherigen Wissens lässt hoffen, dass eine bioenergetische Verwertung städtischen Materials auf allen Ebenen nachhaltig sein könnte.

On Convergence Properties of the EM Algorithm for Gaussian Mixtures

"Expectation-Maximization'' (EM) algorithm and gradient-based approaches for maximum likelihood learning of finite Gaussian mixtures. We show that the EM step in parameter space is obtained from the gradient via a projection matrix $P$, and we provide an explicit expression for the matrix. We then analyze the convergence of EM in terms of special properties of $P$ and provide new results analyzing the effect that $P$ has on the likelihood surface. Based on these mathematical results, we present a comparative discussion of the advantages and disadvantages of EM and other algorithms for the learning of Gaussian mixture models.

Hierarchical Mixtures of Experts and the EM Algorithm

We present a tree-structured architecture for supervised learning. The statistical model underlying the architecture is a hierarchical mixture model in which both the mixture coefficients and the mixture components are generalized linear models (GLIM's). Learning is treated as a maximum likelihood problem; in particular, we present an Expectation-Maximization (EM) algorithm for adjusting the parameters of the architecture. We also develop an on-line learning algorithm in which the parameters are updated incrementally. Comparative simulation results are presented in the robot dynamics domain.

MEASUREMENT AND MODELING OF THE TOXICITY OF BINARY MIXTURES IN THE NEMATODE CAENORHABDITIS ELEGANS-A TEST OF INDEPENDENT ACTION

Ecological risk assessments must increasingly consider the effects of chemical mixtures on the environment as anthropogenic pollution continues to grow in complexity. Yet testing every possible mixture combination is impractical and unfeasible; thus, there is an urgent need for models that can accurately predict mixture toxicity from single-compound data. Currently, two models are frequently used to predict mixture toxicity from single-compound data: Concentration addition and independent action (IA). The accuracy of the predictions generated by these models is currently debated and needs to be resolved before their use in risk assessments can be fully justified. The present study addresses this issue by determining whether the IA model adequately described the toxicity of binary mixtures of five pesticides and other environmental contaminants (cadmium, chlorpyrifos, diuron, nickel, and prochloraz) each with dissimilar modes of action on the reproduction of the nematode Caenorhabditis elegans. In three out of 10 cases, the IA model failed to describe mixture toxicity adequately with significant or antagonism being observed. In a further three cases, there was an indication of synergy, antagonism, and effect-level-dependent deviations, respectively, but these were not statistically significant. The extent of the significant deviations that were found varied, but all were such that the predicted percentage effect seen on reproductive output would have been wrong by 18 to 35% (i.e., the effect concentration expected to cause a 50% effect led to an 85% effect). The presence of such a high number and variety of deviations has important implications for the use of existing mixture toxicity models for risk assessments, especially where all or part of the deviation is synergistic.

Olfactory attractiveness of mixtures of some host plant and conspecific semiochemicals to the banana weevil Cosmopolites sordidus (Germar, 1824)

A simple "Y" shaped olfactometer was used in laboratory studies on the olfactory attractiveness of mixtures in various proportions of industrial analogues of some host plant and conspecific-based semiochemicals, or their combinations with banana rhizome, to the banana weevil. The aim was to identify factors that influence their attractiveness to the weevil, and consider the possibility for their use as lures for trapping the weevil in the field. Cosmopolites sordidus was attracted to the mixtures at specific concentrations and proportions of constituent chemicals. 6-methylhept-5-en-2-one was only attractive on its own at 1 µl/100 ml and in mixture with 4- mercaptophenol, but not at 10 µl, 0.01 µl, or in combination with banana rhizome. 4-mercaptohpenol and 2-n-butylfuran, which were compatible with most host plant-based chemicals and were attractive as a mixture, were perceived to be key elements in the composition of attractants to the weevil. It was concluded that in addition to the composition, other factors that may determine the attractiveness or otherwise of a mixture to C. sordidus are the proportions and concentrations of the constituent chemicals.