Culture alternative medium for the growth of extreme halophilic bacteria in fish products

Halotolerant or halophilic (Archaeabacteria) microorganisms can be found in salted and ripening fish products that are not affected by salt. They can be moderate or extremely halophilic bacteria. The extremely halophilic bacteria require between 15-30% of NaCl for growth. The extremely halophilic archaeobacteria may be selectively isolated in different media. The aim of this work was to determine the effectiveness of the Salt-Agar-Milk medium, a medium modified in our laboratory through the addition of MgSO4 and KCl - named SAMm, and its effect on the bacterial growth by means of comparison with other media, with and without milk, determining time of incubation and counting. Two samples of salted fish from local fish salting factories and two laboratory strains were used. The factory samples were matured anchovy and anchovy fillets in oil, and the laboratory strains were: Haloarcula spp. (proteolytic) and Halococcus spp. (non-proteolytic). The following media were alternatively used for the isolation of extremely halophilic bacteria: IRAM; Formulation of Gibbons and collaborators, Cod Milk agar, and SAMm. IRAM and Gibbons were also used enriched with milk. In the SAMm medium, there were obtained count values similar or higher than the ones of the traditional media; besides the simplicity of its elaboration, the possibility to obtain positive results two or three days earlier also added to its benefit. Consequently, it can be considered an alternative to the media traditionally used for the studied halophilic bacteria.

Conversion of hydroxycinnamic acids into volatile phenols in a synthetic medium and in red wine by Dekkera bruxellensis

The conversion of p-coumaric acid, ferulic acid, and caffeic acid into 4-ethylphenol, 4-ethylguaiacol and 4-ethylcatechol was studied in Dekkera bruxellensis ISA 1791 under defined conditions in a synthetic medium and in a red wine. Liquid chromatography (HPLC-DAD) was used to quantify the phenolic acids, and gas chromatography (GC) coupled to a FID detector was used to quantify volatile phenols using a novel analytical methodology that does not require sample derivatization. Identification was achieved by gas chromatography-mass detection (GC-MS). The results show that phenolic acids concentration decreases while volatile phenols concentration increases. The proportion of caffeic acid taken up by Dekkera bruxellensis is lower than that for p-coumaric or ferulic acid; therefore less 4-ethylcatechol is formed. More important, 4-ethylcathecol synthesis by Dekkera bruxellensis in wine has never been demonstrated so far. These results contribute decisively to a better understanding of the origin of the volatile phenols in wines. The accumulation of these compounds in wine is nowadays regarded as one of the key factors of quality control.

Ability of a Lactobacillus rhamnosus strain cultured in milk whey based medium to bind aflatoxin B1

This study aimed to compare Lactobacillus rhamnosus growth in MRS (de Man, Rogosa and Sharpe) broth and a culture medium containing milk whey (MMW) and to evaluate aflatoxin B1 (AFB1) adsorption capacity by bacterial cells produced in both culture media. L. rhamnosus cells were cultivated in MRS broth and MMW (37 °C, 24 hours), and bacterial cell concentration was determined spectrophotometrically at 600 nm. AFB1 (1 µg/ml) adsorption assays were conducted using 1 x 10(10) non-viable L. rhamnosus cells (121 °C, 15 minutes) at pHs 3.0 and 6.0 and contact time of 60 minutes. AFB1 quantification was performed by High Performance Liquid Chromatography. Bacterial cell concentration in MMW was higher (9.84 log CFU/ml) than that in MRS broth (9.63 log CFU/ml). There were no significant differences between AFB1 binding results at the same pH value (3.0 or 6.0) for the cells cultivated in MRS broth (46.0% and 35.8%, respectively) and in MMW (43.7% and 25.8%, respectively), showing that MMW can adequately replace the MRS broth. Therefore, it can be concluded that the use of L. rhamnosus cells cultivated in MMW offers advantages such as reduction in large scale production costs, improvement of environmental sustainability, and being a practicable alternative for decontamination of food products susceptible to aflatoxin contamination.

Production of medium-chain-length polyhydroxyalkanoate by Pseudomonas oleovorans grown in sugary cassava extract supplemented with andiroba oil

Pseudomonas oleovorans were grown on sugary cassava extracts supplemented with andiroba oil for the synthesis of a mediumchain- length polyhydroxyalkanoate (PHA MCL). The concentration of total sugars in the extract was approximately: 40 g/L in culture 1, 15 g/L in cultures 2 and 3, and 10 g/L in culture 4. Supplementation with 1% andiroba oil and 0.2 g/L of (NH4)2HPO4 was performed 6.5 hours after growth in culture 3, and supplementation with the same amount of andiroba oil and 2.4 g/L of (NH4)2HPO4 was performed at the beginning of growth in culture 4. The synthesis resulted mainly in 3-hydroxy-decanoate and 3-hydroxy-dodecanoate units; 3-hydroxy-butyrate, 3-hydroxy-hexanoate; and 3-hydroxy-octanoate monomers were also produced but in smaller proportions. P. oleovorans significantly accumulated PHA MCL in the deceleration phase of growth with an oxygen limitation but with sufficient nitrogen concentration to maintain cell growth. The sugary cassava extract supplemented with andiroba oil proved to be a potential substrate for PHA MCL production.

PRODUCT DATA MANAGEMENT FOR FINNISH SMALL AND MEDIUM-SIZED MANUFACTURING ENTERPRISES - Towards a viable information system concept

Product Data Management (PDM) systems have been utilized within companies since the 1980s. Mainly the PDM systems have been used by large companies. This thesis presents the premise that small and medium-sized companies can also benefit from utilizing the Product Data Management systems. Furthermore, the starting point for the thesis is that the existing PDM systems are either too expensive or do not properly respond to the requirements SMEs have. The aim of this study is to investigate what kinds of requirements and special features SMEs, operating in Finnish manufacturing industry, have towards Product Data Management. Additionally, the target is to create a conceptual model that could fulfill the specified requirements. The research has been carried out as a qualitative case study, in which the research data was collected from ten Finnish companies operating in manufacturing industry. The research data is formed by interviewing key personnel from the case companies. After this, the data formed from the interviews has been processed to comprise a generic set of information system requirements and the information system concept supporting it. The commercialization of the concept is studied in the thesis from the perspective of system development. The aim was to create a conceptual model, which would be economically feasible for both, a company utilizing the system and for a company developing it. For this reason, the thesis has sought ways to scale the system development effort for multiple simultaneous cases. The main methods found were to utilize platform-based thinking and a way to generalize the system requirements, or in other words abstracting the requirements of an information system. The results of the research highlight the special features Finnish manufacturing SMEs have towards PDM. The most significant of the special features is the usage of project model to manage the order-to-delivery –process. This differs significantly from the traditional concepts of Product Data Management presented in the literature. Furthermore, as a research result, this thesis presents a conceptual model of a PDM system, which would be viable for the case companies interviewed during the research. As a by-product, this research presents a synthesized model, found from the literature, to abstract information system requirements. In addition to this, the strategic importance and categorization of information systems within companies has been discussed from the perspective of information system customizations.

Energy Efficiency in Electrical Drive Systems: Technical potentials, barriers and policy approaches for small and medium industries in Ghana

Today industries and commerce in Ghana are facing enormous energy challenge. The pressure is on for industries to reduce energy consumption, lower carbon emissions and provide se-cured power supply. Industrial electric motor energy efficiency improvement is one of the most important tools to reduce global warming threat and reduce electricity bills. In order to develop a strategic industrial energy efficiency policy, it is therefore necessary to study the barriers that inhibit the implementation of cost – effective energy efficiency measures and the driving forces that promote the implementation. The aim of this thesis is to analyse the energy consumption pattern of electric motors, study factors that promote or inhibit energy efficiency improvements in EMDS and provide cost – effective solutions that improve energy efficiency to bridge the existing energy efficiency gap in the surveyed industries. The results from this thesis has revealed that, the existence of low energy efficiency in motor-driven systems in the surveyed industries were due to poor maintenance practices, absence of standards, power quality issues, lack of access to capital and limited awareness to the im-portance of energy efficiency improvements in EMDS. However, based on the results pre-sented in this thesis, a policy approach towards industrial SMEs should primarily include dis-counted or free energy audit in providing the industries with the necessary information on potential energy efficiency measures, practice best motor management programmes and estab-lish a minimum energy performance standard (MEPS) for motors imported into the country. The thesis has also shown that education and capacity development programmes, financial incentives and system optimization are effective means to promote energy efficiency in elec-tric motor – driven systems in industrial SMEs in Ghana

The interpretation of music videos : an interactive relationship between medium and viewer

There is a great deal of evidence to support the examination of an interactive relationship between the medium and the viewer in the interpretation of mainstream media. The exact nature of this relationship, however, is not well understood. The current study was carried out to assess the variables that may help explain why certain people interpret media, such as music videos, differently than others. Jensen's concept of reception analysis describes the relationship between the medium and the audience, and thus remains a strong focus within this study. Differences in the interpretation of music videos were investigated as a function of Absorption, gender role, screen size, age and viewing experience. Multiple regression analyses uncovered independent predictions of sexuality and violence scores by absorption and experience, as well as an interaction between absorption and screen size in the sexuality rating of the music videos.

The effects of plants(Typha Latifolia)and root-bed medium on the treatment of domestic sewage within a vertical flow constructed wetland /

The effect that plants {Typha latifolia) as well as root-bed medium physical and chemical characteristics have on the treatment of primary treated domestic wastewater within a vertical flow constructed wetland system was investigated. Five sets of cells, with two cells in each set, were used. Each cell was made of concrete and measured 1 .0 m X 1 .0 m and was 1.3 m deep. Four different root-bed media were tested : Queenston Shale, Fonthill Sand, Niagara Shale and a Michigan Sand. Four of the sets contained plants and a single type of root-bed medium. The influence of plants was tested by operating a Queenston Shale set without plants. Due to budget constraints no replicates were constructed. All of the sets were operated independently and identically for twenty-eight months. Twelve months of data are presented here, collected after 16 months of continuous operation. Root-bed medium type did not influence BOD5 removal. All of the sets consistently met Ontario Ministry of Environment (MOE) requirements (<25 mg/L) for BOD5 throughout the year. The 12 month average BOD5 concentration from all sets with plants was below 2.36 mg/L. All of the sets were within MOE discharge requirements (< 25 mg/L) for suspended solids with set effluent concentrations ranging from 1.53 to 14.80 mg/L. The Queenston Shale and Fonthill Sand media removed the most suspended solids while the Niagara Shale set produced suspended solids. The set containing Fonthill Sand was the only series to meet MOE discharge requirements (< Img/L) for total phosphorus year-round with a twelve month mean effluent concentration of 0.23 mg/L. Year-round all of the root-bed media were well below MOE discharge requirements (< 20mg/L in winter and < 10 mg/L in sumnner) for ammonium. The Queenston Shale and Fonthill Sand sets removed the most total nitrogen. Plants had no effect on total nitrogen removal, but did influence how nitrogen was cycled within the system. Plants increased the removal of suspended solids by 14%, BOD5 by 10% and total phosphorus by 22%. Plants also increased the amount of dissolved oxygen that entered the system. During the plant growing season removal of total phosphorus was better in all sets with plants regardless of media type. The sets containing Queenston Shale and Fonthill Sand media achieved the best results and plants in the Queenston Shale set increased treatment efficiency for every parameter except nitrogen. Vertical flow wetland sewage treatment systems can be designed and built to consistently meet MOE discharge requirements year-round for BOD5, suspended solids, total phosphorus and ammonium. This system Is generally superior to the free water systems and sub-surface horizontal flow systems in cold climate situations.

Explaining the Great Divergence: Medium and Message on the Eurasian Land Mass, 1700-1850

Between 1700 and 1850, per-capita income doubled in Europe while falling in the rest of Eurasia. Neither geography nor economic institutions can explain this sudden divergence. Here the consequences of differences in communications technology are examined. For the first time, there appeared in Europe a combination of a standardized medium (national vernaculars with a phonetic alphabet) and a non-standardized message (competing religious, political and scientific ideas). The result was an unprecedented fall in the cost of combining ideas and burst of productivity-raising innovation. Elsewhere, decreasing standardization of the medium and increasing standardization of the message blocked innovation.

Poly(ethylene-co-acrylic acid) random copolymers : amphiphilic properties and self-assembly in aqueous medium

Les travaux de recherche présentés ici avaient pour objectif principal la synthèse de copolymères statistiques à base d’éthylène et d’acide acrylique (AA). Pour cela, la déprotection des groupements esters d’un copolymère statistique précurseur, le poly(éthylène-co-(tert-butyl)acrylate), a été effectuée par hydrolyse à l’aide d’iodure de triméthylsilyle. La synthèse de ce précurseur est réalisée par polymérisation catalytique en présence d’un système à base de Palladium (Pd). Le deuxième objectif a été d’étudier et de caractériser des polymères synthétisés à l’état solide et en suspension colloïdale. Plusieurs copolymères précurseurs comprenant différents pourcentages molaires en tert-butyl acrylate (4 à 12% molaires) ont été synthétisés avec succès, puis déprotégés par hydrolyse pour obtenir des poly(éthylène-coacide acrylique) (pE-co-AA) avec différentes compositions. Seuls les copolymères comprenant 10% molaire ou plus de AA sont solubles dans le Tétrahydrofurane (THF) et uniquement dans ce solvant. De telles solutions peuvent être dialysées dans l’eau, ce qui conduit à un échange lent entre cette dernière et le THF, et l’autoassemblage du copolymère dans l’eau peut ensuite être étudié. C’est ainsi qu’ont pu être observées des nanoparticules stables dans le temps dont le comportement est sensible au pH et à la température. Les polymères synthétisés ont été caractérisés par Résonance Magnétique Nucléaire (RMN) ainsi que par spectroscopie Infra-Rouge (IR), avant et après déprotection. Les pourcentages molaires d’AA ont été déterminés par combinaison des résultats de RMN et ii de titrages conductimètriques. A l’état solide, les échantillons ont été analysés par Calorimétrie différentielle à balayage (DSC) et par Diffraction des rayons X. Les solutions colloïdales des polymères pE-co-AA ont été caractérisées par Diffusion dynamique de la lumière et par la DSC-haute sensibilité. De la microscopie électronique à transmission (TEM) a permis de visualiser la forme et la taille des nanoparticules.

Enhancement of Diffraction Efficiency and Storage Life of Poly (Vinyl Chloride) Based Optical Recording Medium with the Incorporation of an Electron Donor

The differaction efficiency,sensitivity and storage life of Methylene Blue sencitized poly (vinyl chloride) film was improved by the addition of an electron donor in the matrix. The addition of pyridine enhanced the diffraction efficiency by two times and storage life of the gratings was increased to 2-3 days.

Reusable Recording Medium Based on MBPVA and Vinyl Acetate

A new photopolymerizable recording media is introduced based on poly (vinyl alcohol) and vinyl acetate sensitized with methylene blue. It is observed that this MBPVA/VAc system can be reused a number of times without significant decrease in diffraction efficiency. The PVA-VAc ratio was optimized at 2:1. Diffraction efficiency of 6.3% was obtained without any fixing at a dye concentration of 9.3 10 4 mol/l at an exposure of 750 mJ/cm2. The material is attractive on account of its reusability.