Synthesis, structural and morphological characterization of CeO2-ZnO nanosized powder systems from Pechini's method

This work reports on the investigation of nanosized CeO2-ZnO systems prepared by Pechini's method. The structural and morphological characterization of CeO2-ZnO systems as well as the characterization of CeO2 and ZnO separately, showed that the employed method result in powders with spheroidal particles whose size are in the range 30 - 200 nm, which is appropriate to provide homogeneous suspensions. The ZnO present in the prepared mixed oxides seems to increase particle size distribution and to influence the arrangement of the particles after powder dispersion.

COMPARISON BETWEEN WOOD DRYING DEFECT SCORES: SPECIMEN TESTING X ANALYSIS OF KILN-DRIED BOARDS

It is important to develop drying technologies for Eucalyptus grandis lumber, which is one of the most planted species of this genus in Brazil and plays an important role as raw material for the wood industry. The general aim of this work was to assess the conventional kiln drying of juvenile wood of three clones of Eucalyptus grandis. The specific aims were to compare the behavior between: i) drying defects indicated by tests with wood specimens and conventional kiln-dried boards; and ii) physical properties and the drying quality. Five 11-year-old trees of each clone were felled, and only flatsawn boards of the first log were used. Basic density and total shrinkage were determined, and the drying test with wood specimens at 100 °C was carried out. Kiln drying of boards was performed, and initial and final moisture content, moisture gradient in thickness, drying stresses and drying defects were assessed. The defect scoring method was used to verify the behavior between the defects detected by specimen testing and the defects detected in kiln-dried boards. As main results, the drying schedule was too severe for the wood, resulting in a high level of boards with defects. The behavior between the defects in the drying test with specimens and the defects of kiln-dried boards was different, there was no correspondence, according to the defect scoring method.

Segregation of powder mixtures in silos with particular reference to dry mineral-based construction materials

Segregering eller segregation är ett fenomen som kan förekomma inom olika områden av samhället. Inom samhällsvetenskaperna kan segregering definieras som det rumsliga åtskiljandet av befolkningsgrupper på urval av ras eller etniskt ursprung, kön, social härkomst, religion, ålder, yrke, osv. Segregering av befolkningsgrupper sker ofta mer eller mindre frivilligt och är motsatsen till integration. Inom partikelteknologi definieras segregering oftast som det rumsliga åtskiljandet av beståndsdelarna i en blandning av olika partiklar. Segregering sker då på urval av bl.a. partiklarnas storlek, densitet, form, elektrostatiska eller mekaniska egenskaper, och kan beskrivas som motsatsen till blandning. Segregeringsmekanismer används för att förklara hur och varför en partikelblandning segregerar samt vad slutresultatet i form av den rumsliga fördelningen av partiklarna blir till följd av att blandningen utsetts för en viss behandling. I denna avhandling har segregering av partikelblandningar och speciellt torra mineralbaserade byggmaterial (t.ex. murbruk) till följd av lagring i siloer studerats. Vid industriell produktion av mineralbaserade byggmaterial används siloer för korttidslagring av slutprodukterna precis innan förpackning. Segregering leder till kraftiga variationer i sammansättningen för partikelströmmen ut ur silon, vilket gör att slutprodukterna inte uppfyller kvalitetskraven och kan därmed inte säljas till kunder. Detta leder till arbetsam och dyr bearbetning (återcirkulation) av produkterna med påföljder för produktionsekonomin samt hållbara utvecklingen. I avhandlingen identifierades de väsentligaste segregeringsmekanismerna för torra mineralbaserade byggmaterial i siloer. Dessutom klargjordes effekterna av materialegenskaper, processbetingelser och siloparametrar. Slutligen behandlas möjliga åtgärder för minskning av partikelsegregering i siloer samt tillämpning av matematiska metoder för simulering av partikelflöden med hjälp av datorer.

Powder flow criteria for design of vertical silo walls

For design of vertical silos walls involving the storage of bulk solids to be safe and reliable, it is important knowing the largest possible number of variables such as: flow properties, silo geometry and pattern of flow desired. In order to validate the theories of flow prediction and design of conical hoppers, the flow properties of two bulk solids were determined, the theories of Jenike's flowability and Enstad and Walker for hopper design were analyzed and the results were compared with those experimentally obtained in a reduced model of a semicircular-section silo. Results show that Enstad theory for the hopper design is adequate to occur mass flow inside the silo, and for the sizing of the discharge outlet, the Walker's theory was closer to the appropriate than Jenike's theory, which was higher around 100% than the experimental hopper outlet.

Enhancing the Usability of Drug Materials by Electrostatic Atomisation

Electrospraying or electrostatic atomisation is a process of liquid disruption by electrostatic forces. When liquid is brought into an electric field, charge is induced to its surface. Once the repulsive electrostatic force exceeds the liquid surface tension, the liquid disrupts into small highly charged droplets. The size of the electrosprayed droplets can range from hundreds of micrometers down to a few tens of nanometers. Electrospraying can be used not only to produce droplets, but also solid particles. The research presented in this thesis concentrates on producing drug particles by this method. In the experiments, a drug powder was dissolved in a convenient solvent and the solution was atomised. The solvent was then evaporated from the formed droplets in a drying medium and inside each droplet, a dense cluster of the dissolved drug remained. From the pharmaceutical point of view, the most important characteristics of the produced particles are size distribution, porosity, crystal form and degree of crystallinity. These properties affect the dissolution behaviour and ultimately the drug bioavailability in the body. The effects of electrostatic atomization on the aforementioned characteristics are generally not well understood. The research focused on studying these particle properties and finding possible correlations with the spraying parameters. The produced droplets were dried either under atmospheric or reduced pressure, the latter in order to improve the drying process. Special emphasis was put on implementing the spraying under reduced pressure, and the effects of the drying pressure on particle properties. Based on the results, the possibilities to enhance the dissolution of poorly soluble drugs by this method were estimated. In the course of experiments, it was also discovered that electrospraying may have a profound effect on the polymorphic form of the produced drug particles. In the light of the obtained results, it was concluded that electrospraying may offer a valuable tool to overcome some of the challenges met in modern drug development and formulation.

Early myelin breakdown following sural nerve crush: a freeze-fracture study

In this study we describe the early changes of the myelin sheath following surgical nerve crush. We used the freeze-fracture technique to better evaluate myelin alterations during an early stage of Wallerian degeneration. Rat sural nerves were experimentally crushed and animals were sacrificed by transcardiac perfusion 30 h after surgery. Segments of the nerves were processed for routine transmission electron microscopy and freeze-fracture techniques. Our results show that 30 h after the lesion there was asynchrony in the pattern of Wallerian degeneration, with different nerve fibers exhibiting variable degrees of axon disruption. This was observed by both techniques. Careful examination of several replicas revealed early changes in myelin membranes represented by vacuolization and splitting of consecutive lamellae, rearrangement of intramembranous particles and disappearance of paranodal transverse bands associated or not with retraction of paranodal myelin terminal loops from the axolemma. These alterations are compatible with a direct injury to the myelin sheath following nerve crush. The results are discussed in terms of a similar mechanism underlying both axon and myelin breakdown.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Preclinical evaluation of the antidiabetic effect of Eugenia jambolana seed powder in streptozotocin-diabetic rats

The world is facing an explosive increase in the incidence of diabetes mellitus and cost-effective complementary therapies are needed. The effects of Eugenia jambolana, a household remedy for diabetes, were studied. Streptozotocin diabetic female albino Wistar rats weighing 150-200 g (N = 6) were fed E. jambolana seed powder (250, 500 or 1000 mg/kg) for 15 days. Diabetic rats fed 500 and 1000 mg/kg seed powder showed an increase in body weight on day 20 in relation to day 5 (6 ± 4.7, 9 ± 7.8 vs diabetic control -16 ± 7.1 g, P < 0.001), a decrease in fasting blood glucose (75 ± 11.9, 123 ± 14.4 vs diabetic control -34 ± 12.1 mg/dl, P < 0.001), a difference in post-treatment fasting and peak blood glucose (38 ± 11.9, 36 ± 14.2 vs diabetic control 78 ± 11.9 mg/dl, P < 0.001), and a difference in liver glycogen (50 ± 6.8, 52 ± 7.5 vs normal control 90 ± 6.6 µg/g of liver tissue, P < 0.001). Tri-terpenoids, tannins, gallic acid, and oxalic acid were the chemical constituents detected in E. jambolana seed. The best results were obtained with an oral dose of 500 mg/kg. Subacute toxicity studies with a single administration of 2.5 and 5.0 g/kg seed powder showed no mortality or abnormality. These data on the antidiabetic effect of E. jambolana seed are adequate for approval of phase 2 clinical trials to evaluate this seed powder as complementary therapy in type 2 and type 1 diabetes.

Metal additive manufacturing of internal flow channels with powder bed fusion processes

This thesis studies the advantages, disadvantages and possibilities of additive manufacturing in making components with internal flow channels. These include hydraulic components, components with cooling channels and heat exchangers. Processes studied in this work are selective laser sintering and selective laser melting of metallic materials. The basic principles of processes and parameters involved in the process are presented and different possibilities of internal channel manufacturing and flow improvement are introduced

Antinutrients in the cassava (Manihot esculenta Crantz) leaf powder at three ages of the plant

In Brazil, the cassava leaf meal (CLM) has been used to strive against undernourishment because it is a high source of vitamins and minerals. However, the wide variation in the chemical composition of the different cultivars, as well as their antinutritional substances may be a restriction to their uses. The levels of some antinutrients in CLM from five cultivars at three ages of the plant (TAP) were investigated, in order to select the cultivars and plant ages that would be more appropriate for human consumption. The lowest contents of antinutrients were observed in the 12-month old plants, except for nitrate and hemagglutinin from which the lowest contents were found for the 17 month old ones. The cultivar IAC 289-70 had the lowest antinutrient levels, except for saponin and oxalate. Thus, the cultivar IAC 289-70 at 12 months is the most appropriate for human consumption.

Weldability of powder bed fusion fabricated stainless steel 316L sheets to cold rolled sheet metal

Weldability of powder bed fusion (PBF) fabricated components has come to discussion in past two years due to resent developments in the PBF technology and limited size of the machines used in the fabrication process. This study concentrated on effects of energy input of welding on mechanical properties and microstructural features of welds between PBF fabricated stainless steel 316L sheets and cold rolled sheet metal of same composition by the means of destructive testing and microscopic analysis. Optical fiber diameter, laser power and welding speed were varied during the experiments that were executed following one variable at a time (OVAT) method. One of the problems of welded PBF fabricated components has been lower elongations at break comparing to conventionally manufactured components. Decreasing energy input of the laser keyhole welding decreased elongations at break of the welded specimens. Ultimate tensile strengths were not affected significantly by the energy input of the welding, but fracturing of the specimens welded using high energy input occurred from the weld metal. Fracturing of the lower energy input welds occurred from the PBF fabricated base metal. Energy input was found to be critical factor for mechanical properties of the welds. Multioriented grain growth and formation of neck at fusion zone boundary on the cold rolled side of the weld was detected and suspected to be result from weld pool flows caused by differences in molten weld pool behaviour between the PBF fabricated and cold rolled sides of the welds.

Microparticles obtained by complex coacervation: influence of the type of reticulation and the drying process on the release of the core material

Microparticles obtained by complex coacervation were crosslinked with glutaraldehyde or with transglutaminase and dried using freeze drying or spray drying. Moist samples presented Encapsulation Efficiency (%EE) higher than 96%. The mean diameters ranged from 43.7 ± 3.4 to 96.4 ± 10.3 µm for moist samples, from 38.1 ± 5.36 to 65.2 ± 16.1 µm for dried samples, and from 62.5 ± 7.5 to 106.9 ± 26.1 µm for rehydrated microparticles. The integrity of the particles without crosslinking was maintained when freeze drying was used. After spray drying, only crosslinked samples were able to maintain the wall integrity. Microparticles had a round shape and in the case of dried samples rugged walls apparently without cracks were observed. Core distribution inside the particles was multinuclear and homogeneous and core release was evaluated using anhydrous ethanol. Moist particles crosslinked with glutaraldehyde at the concentration of 1.0 mM.g-1 protein (ptn), were more efficient with respect to the core retention compared to 0.1 mM.g-1 ptn or those crosslinked with transglutaminase (10 U.g-1 ptn). The drying processes had a strong influence on the core release profile reducing the amount released to all dry samples

Comparison of methodologies for moisture determination on dried bee pollen samples

Bee pollen moisture value is one of the quality parameters for this product. Some countries such as Argentina, Brazil, Bulgaria, Poland and Switzerland have bee pollen regulations on quality parameters, but these are not clear regarding which method should be used for moisture determination. The aim of this paper was to compare six methods of moisture determination in dried bee pollen samples. The methods were: conventional oven at 100 °C, vacuum oven at 70 °C, desiccator with sulfuric acid, drying out process with infrared light at 85 °C, lyophilization and Karl Fisher's method. Based on the results, the best methods for moisture determination of bee pollen were the drying process with infrared and the lyophilization, since these have shown lower moisture values.

Application of mathematical models for the prediction of adsorption isotherms in solid mixture for mango powder refreshment

Solid mixtures for refreshment are already totally integrated to the Brazilian consumers' daily routine, because of their quick preparation method, yield and reasonable price - quite lower if compared to 'ready-to-drink' products or products for prompt consumption, what makes them economically more accessible to low-income populations. Within such a context, the aim of this work was to evaluate the physicochemical and mineral composition, as well as the hygroscopic behavior of four different brands of solid mixture for mango refreshment. The BET, GAB, Oswim and Henderson mathematical models were built through the adjustment of experimental data to the isotherms of adsorption. Results from the physiochemical evaluation showed that the solid mixtures for refreshments are considerable sources of ascorbic acid and reductor sugar; and regarding mineral compounds, they are significant sources of calcium, sodium and potassium. It was also verified that the solid mixtures for refreshments of the four studied brands are considered highly hygroscopic.

Technological properties of precooked flour containing coffee powder and rice by thermoplastic extrusion

Although Brazil is a country of tradition in both the production and consumption of coffee, the most of the coffee is consumed as a beverage, which reduces greatly the competitiveness on international market, for reducing the chances of supplying the product under other forms of consumption. Owing to that, the aim of this study was developing a precooked mixed flour containing coffee powder and rice for use in coffee flavored products. Mixtures of rice and coffee in the proportions of 900:100, 850:150 and 800:200 g, respectively, were processed in a single screw extruder (Brabender DS-20, Duisburg, German) and the effect of the extrusion process on the variables moisture content (16%, 18% and 20%) and temperature in the third extruding zone (140 °C, 160 °C and 180 °C) was studied. The results for expansion index ranged from 2.91 to 11.11 mm in diameter; the water absorption index from 4.59 to 6.33 g gel/g sample and the water solubility index varied from 4.05% to 8.57%. These results showed that, despite coffee powder influenced the variables studied, the expanded product after milling resulted in a extruded mixture with good absorption and water solubility indices, which favors the use of the precooked mixed flour for human consumption.