A critical examination of the paradox of strength and ductility in ultrafine-grained metals

The paradox of strength and ductility is now well established and denotes the difficulty of simultaneously achieving both high strength and high ductility. This paradox was critically examined using a cast Al-7% Si alloy processed by high-pressure torsion (HPT) for up to 10 turns at a temperature of either 298 or 445 K. This processing reduces the grain size to a minimum of similar to 0.4 mu m and also decreases the average size of the Si particles. The results show that samples processed to high numbers of HPT turns exhibit both high strength and high ductility when tested at relatively low strain rates and the strain rate sensitivity under these conditions is similar to 0.14 which suggests that flow occurs by some limited grain boundary sliding and crystallographic slip. The results are also displayed on the traditional diagram for strength and ductility and they demonstrate the potential for achieving high strength and high ductility by increasing the number of turns in HPT.

Examination of the LBM in simulation of microchannel flow in transitional regime

The gas flows in micro-electro-mechanical systems possess relatively large Knudsen number and usually belong to the slip flow and transitional flow regimes. Recently the lattice Boltzmann method (LBM) was proposed by Nie et al. in Journal of Statistical Physics, vol. 107, pp. 279-289, in 2002 to simulate the microchannel and microcavity flows in the transitional flow regime. The present article intends to test the feasibility of doing so. The results of using the lattice Boltzmann method and the direct simulation Monte Carlo method show good agreement between them for small Kn (Kn = 0.0194), poor agreement for Kn = 0.194, and large deviation for Kn = 0.388 in simulating microchannel flows. This suggests that the present version of the lattice Boltzmann method is not feasible to simulate the transitional channel flow.

"I'm on it 24/7 at the moment" : A qualitative examination of multi-screen viewing behaviours among UK 10-11 year olds

Background: Screen-viewing has been associated with increased body mass, increased risk of metabolic syndrome and lower psychological well-being among children and adolescents. There is a shortage of information about the nature of contemporary screen-viewing amongst children especially given the rapid advances in screen-viewing equipment technology and their widespread availability. Anecdotal evidence suggests that large numbers of children embrace the multi-functionality of current devices to engage in multiple forms of screen-viewing at the same time. In this paper we used qualitative methods to assess the nature and extent of multiple forms of screen-viewing in UK children. Methods: Focus groups were conducted with 10-11 year old children (n = 63) who were recruited from five primary schools in Bristol, UK. Topics included the types of screen-viewing in which the participants engaged; whether the participants ever engaged in more than one form of screen-viewing at any time and if so the nature of this multiple viewing; reasons for engaging in multi-screen-viewing; the room within the house where multi-screen-viewing took place and the reasons for selecting that room. All focus groups were transcribed verbatim, anonymised and thematically analysed. Results: Multi-screen viewing was a common behaviour. Although multi-screen viewing often involved watching TV, TV viewing was often the background behaviour with attention focussed towards a laptop, handheld device or smart-phone. There were three main reasons for engaging in multi-screen viewing: 1) tempering impatience that was associated with a programme loading; 2) multi-screen facilitated filtering out unwanted content such as advertisements; and 3) multi-screen viewing was perceived to be enjoyable. Multi-screen viewing occurred either in the child's bedroom or in the main living area of the home. There was considerable variability in the level and timing of viewing and this appeared to be a function of whether the participants attended after-school clubs. Conclusions: UK children regularly engage in two or more forms of screen-viewing at the same time. There are currently no means of assessing multi-screen viewing nor any interventions that specifically focus on reducing multi-screen viewing. To reduce children's overall screen-viewing we need to understand and then develop approaches to reduce multi-screen viewing among children.

An examination of the Community Fisheries Sub-Decree in Cambodia: changes and developments during the drafting process

This study examines the development of the Community Fisheries Sub-Decree. From its promulgation in late 2000 through its draft form in June 20021, this sub-decree has gone through over 25 drafts. Initially, the writing process involved the public intimately: community meetings were conducted, NGOs contributed their knowledge and expertise, and then, with these consultations in mind, the newly-formed Community Fisheries Development Office (CFDO) in the Department of Fisheries (DoF) drafted the sub-decree. Over the following year and a half, the sub-decree went through numerous changes, some of which fundamentally alter the tenor of the legislation. This includes the deletion of some of the primary issues of rural communities, such as what fishing gears they can use and whether they can participate in patrolling the fishing area. While the final form is still pending, there are many questions as to the positive effects that the sub-decree will ultimately have on people’s livelihoods when it is finally approved. This research was undertaken to track the development of the sub-decree to gain a better understanding of how the Cambodian policy-making system functions. Consultations were undertaken with the DoF and CFDO before the research began, both of which agreed to the study. It is hoped that this report will help not only those interested in community fisheries issues, but also those who want to advocate on other Cambodian development issues as well. Due to the sensitive nature of the subject material, and the fact that the sub-decree is still pending, the author has conducted interviews with the express purpose of keeping them confidential. Therefore, no individual will be quoted directly in this study. In addition, many of the English versions of the drafts examined were unofficial translations. The author has made no effort to correct the English in the drafts. Moreover, there are also questions regarding the drafts and their sequence, as no government records were kept of the process or the changes that were made along the way. These have been compiled after the fact. (33 p.)

Estimating age of spotted and spinner dolphins (Stenella attenuata and Stenella longirostris) from teeth

This paper is an account of preparation and examination techniques and criteria used to estimate age in decalcified and stained tooth thin sections from spinner and spotted dolphins. A dentinal growth layer group (GLG), composed of two thin light and two thicker dark-stained layers, is deposited annually. The GLG component layers are variably visible, but the "ideal" pattern and successive thinning of dentinal GLGs are used as a guide to determine GLG limits. Age-specific thicknesses of dentinal GLGs found in Hawaiian spinner dolphin teeth seem to be applicable to teeth of spotted dolphins and can be used as an aid in locating GLG boundaries. Cementa1 GLGs are composed of a dark-stained and alightly stained layer and usually are deposited at a rate of one per year, but may be deposited every other year or two or three times per year. Two slightly different methods of counting dentinal GLGs are presented, along with guidelines for determining whether dentinal or cementa1 GLG counts provide the best estimate of age for a specimen. (PDF contains 23 pages.)

KE Useage Statistics Guidelines

A Knowledge Exchange workshop took place in March 2010 to bring together technical experts working in partner projects collecting usage statistics including PIRUS2, OAstatistik and SURFsure projects. Experts from other related projects (RePec and NeeO) were also involved. Following the workshop, experts came to the conclusion that it would be valuable for institutions in all four Knowledge Exchange partner countries as well as countries outside of KE, to have an agreed set of guidelines which could be used when collecting and comparing data on usage statistics. This work connects with work already planned in projects already funded in three of the countries. Together they have set up a set of guidelines which will be tested and refined by Autumn 2010. An element in these guidelines is an agreed robotlist. This list extends on the COUNTER list of robots which should be excluded when counting downloads.

An examination of fluctuations in the “concentration index” of purse seiners and baitboats in the fishery for tropical tunas in the Eastern Pacific, 1951-1961

ENGLISH: In the eastern Pacific Ocean nearly all of the commercial catches of yellowfin tuna (Thunnus albacares) and skipjack (Katsuwonus pelamis) are taken by two types of vessels, baitboats, which use pole and line in conjunction with live-bait, and purse-seiners. From its inception until very recently (1959), this fishery was dominated by baitboats. This method of fishing has been described by Godsil (1938) and Shimada and Schaefer (1956). From 1951 through 1958 baitboats caught between 66.4 and 90.8 per cent of the yellowfin and between 87.2 and 95.3 per cent of the skipjack landed by the California-based fleet. These vessels fished for tuna throughout the year and covered virtually all of the area from southern California to northern Chile. The purse-seine fishery for tunas developed out of the round-haul net fisheries for California sardines and other species. Scofield (1951) gives a detailed description of the development of gear and fishing methods. Prior to 1959 many of the seiners engaged in other fisheries during the fall and early winter months and consequently most of the fishing effort for tuna occurred in the period February-August. The vessels were quite small, averaging approximately 120 tons carrying capacity (Broadhead and Marshall, 1960), in comparison to the baitboats, of which the most numerous size-class was 201-300 tons. The seiners were naturally more restricted in range than the baitboats and most of their effort was restricted to the northern grounds. During the period 1959-61 most of the large baitboats were converted for purse-seining and the existing seiner fleet was modernized. These developments increased the range of the seiner fleet and resulted in a wider and more nearly even spatial and temporal distribution of effort. By the early part of 1961, the purse-seine fleet approximated the level of the preconversion baitboat fleet in amount of effort applied and area covered. The changes in the purse-seine fishery and the fishing methods employed in the modernized fleet are described by Orange and Broadhead (1959), Broadhead and Marshall (1960), McNeely (1961) and Broadhead (1962). The change in the relative importance of the two gears is illustrated by the decline in the proportion of the total logged tonnage landed by California-based baitboats, in comparison to the proportion landed by seiners. In 1959 baitboats landed 49.5 per cent of the yellowfin and 87.8 per cent of the skipjack. In 1960 these percentages were 22.9 and 74.7 respectively and in 1961 the decline continued to 12.6 per cent of the yellowfin and 30.0 per cent of the skipjack (Schaefer, 1962). In previous Bulletins of this Commission (Griffiths, 1960; Calkins, 1961) the baitboat catch and effort statistics were used to compute two indices of population density and an index of concentration of fishing effort and the fluctuations of these indices were analyzed in some detail. Due to the change in the relative importance of the two gears it is appropriate to extend this investigation to include the purse-seine data. The objectives of this paper are to compute two indices of population density and an index of concentration of fishing effort and to examine the fluctuations in these indices before and after the changes in the fishery. A further objective is to compare the purse-seine indices with those of the baitboats for the same time periods. SPANISH: En el Océano Pacífico Oriental casi todas las capturas comerciales del atún aleta amarilla (Thunnus albacares) y del barrilete (Katsuwonus pelamis) son efectuadas por dos tipos de barcos, los barcos de carnada que emplean la caña y el anzuelo en conjunto con la carnada viva, y los barcos rederos. Desde su comienzo hasta hace poco tiempo (1959), esta pesquería estaba dominada por los barcos de carnada. El método de pesca usado por estos barcos ha sido descrito por Godsil (1938) y por Shimada y Schaefer (1956). De 1951 a 1958, los barcos de carnada pescaron entre el 66.4 y el 90.8 por ciento del atún aleta amarilla y entre el 87.2 y el 95.3 por ciento del barrilete descargados por la flota que tiene su base en California. Estos barcos pescaron atún durante todo el año y cubrieron virtualmente toda el área de California meridional hasta la parte norte de Chile. La pesquería del atún con redes de cerco se originó en las pesquerías de las sardinas de California y otras especies, con redes que se remolcaban circularmente. Scofield (1951) dá una descripción detallada del desarrollo de los métodos y del equipo de pesca. Antes de 1959 muchos de los rederos se dedicaban a otras pesquerías durante los meses del otoño y a principios del invierno y consecuentemente, la mayor parte del esfuerzo depesca para la producción del atún ocurría en el período febrero-agosto. Las embarcaciones eran bastante pequeñas, con un promedio de aproximadamente 120 toneladas de capacidad para el transporte (Broadhead y Marshall, 1960) en comparación con los barcos de carnada, de los cuales la clase de tamaño más numerosa era de 201 a 300 toneladas. Los rederos estaban naturalmente más restringidos en su radio de acción que los barcos de carnada y la mayor parte de su esfuerzo se limitaba a las localidades del norte. Durante el período 1959-61, la mayoría de los grandes barcos de carnada fueron convertidos al sistema de pesca con redes de cerco, y se modernizó la flota existente de los rederos. Estos cambios aumentaron el alcance de la flota de los barcos rederos dando como resultado una distribución más amplia y casi más uniforme del esfuerzo espaciado y temporal. En la primera parte del año 1961, la flota de rederos se aproximó al nivel de la preconversión de la flota de clipers, en la cantidad de esfuerzo aplicado y al área comprendida. Los cambios en la pesquería con red y los métodos de pesca empleados en la flota modernizada, han sido descritos por Orange y Broadhead (1959), Broadl1ead y Marshall (1960), McNeely (1961) y Broadhead (1962). El cambio en la importancia relativa de los dos sistemas de pesca está ilustrado por la declinación en la proporción del tonelaje total registrado, como descargado por los barcos de carnada que tienen su base en California, comparado con la proporción desembarcada por los barcos rederos. En 1959 los clipers descargaron el 49.5 por ciento del atún aleta amarilla y el 87.8 por ciento del barrilete. En 1960 estos porcentajes fueron del 22.9 y 74.7 respectivamente, y en 1961 continuó la reducción hasta el 12.6 por ciento del atún aleta amarilla y el 30.0 por ciento del barrilete (Schaefer, 1962). En Boletines anteriores de la Comisión (Griffiths, 1960; Calkins, 1961) las estadísticas de la pesca y el esfuerzo de los clipers se utilizaron para computar dos índices de la densidad de población y un índice de la concentración del esfuerzo de pesca, y se analizaron algo detalladamente las fluctuaciones de estos índices. Debido al cambio en la importancia relativa de los dos sistemas de pesca, es conveniente extender esta investigación para incluir los datos correspondientes a los barcos rederos. Los objetivos del presente estudio son de computar dos índices de la densidad de población y un índice de la concentración del esfuerzo de pesca, y examinar las fluctuaciones en estos índices, antes y después de los cambios en la pesquería. Otro objetivo es de comparar los índices de los barcos rederos, con aquellos de los clipers en los mismos períodos de tiempo.

Guidelines for the Provision of Garbage Reception Facilities at Ports Under MARPOL Annex V

This report offers guidelines for the provision of adequate port reception facilities for vessel-generated garbage under the requirements of Annex V of the International Convention for the Prevention of Pollution From Ships, 1973 (MARPOL 73/78), Regulations for the Prevention of Pollution by Garbage from Ships. MARPOL Annex V prohibits at-sea disposal of plastic materials from vessels, and specifies the distance from shore at which other materials may be dumped. Annex V also requires the provision of port reception facilities for garbage, but it does not specify these facilities or how they are to be provided. Since the at-sea dumping restrictions apply to all vessels, the reception facility requirement applies to all ports, terminals, and marinas that serve vessels. These guidelines were prepared to assist port owners and operators in meeting their obligation to provide adequate reception facilities for garbage. The report synthesizes available information and draws upon experience from the first years ofimplementation of MARPOL Annex V. (PDF file contains 55 pages.)

Guidelines for reducing porpoise mortality in tuna purse seining

More than a decade has passed since the passage of the Marine Mammal Protection Act of 1972. During that time the U.S. tuna purse seine neet reduced its incidental porpoise mortality rate more than 10-fold. This was made possible through the development of gear and techniques aimed at reducing the frequency of many low probability events that contribute to the kill. Porpoise are killed by becoming entangled or entrapped in folds and canopies of the net and suffocating. The configuration of the net, both before and during the backdown release procedure, is a major determinant of the number of porpoise killed. Speedboats can be used to tow on the corkllne to prevent net collapse and also to adjust the net configuration to reduce net canopies prior to backdown. Deepening a net can reduce the probability of porpoise being killed by prebackdown net collapse. The effects of environmental conditions and mechanical failures on net configuration can result in high porpoise mortality unless mitigated by skilled vessel maneuvers or prevented by the timely use of speedboats to adjust the net. The backdown procedure is the only means to effectively release captured porpoise from a purse seine. It is also the time during the set when most of the mortality occurs. The use of small mesh safety panels and aprons in the backdown areas of nets reduces porpoise entanglement, and Increases the probability of an effective release. The tie-down points on the net for preparing the backdown channel must be properly located in order to optimize porpoise release. A formula uses the stretched depth of the net to calculate one of these points, making it a simple matter to locate the other. Understanding the dynamics of the backdown procedure permits a thorough troubleshooting of performance, thus preventing the repetition of poorly executed backdowns and thereby reducing mortality. Porpoise that cannot be released must be rescued by hand. A rescuer in a rigidly inflated raft can rescue porpoise effectively at any time during a net set. Hand rescue can make the difference between above average kill and zero kill sets. In all circumstances, the skill and motivation of the captain and his crew are the final determinants in the prevention of incidental porpoise mortality in tuna seining. (PDF file contains 22 pages.)