Development of calix[4]arene-functionalized microcantilever array sensing system for the rapid, sensitive and simultaneous detection of metal ions in aqueous solutions

The work described in this thesis was conducted with the aim of: 1) investigating the binding capabilities of calix[4]arene-functionalized microcantilevers towards specific metal ions and 2) developing a new16-microcantilever array sensing system for the rapid, and simultaneous detection of metal ions in fresh water. Part I of this thesis reports on the use of three new bimodal calix[4]arenes (methoxy, ethoxy and crown) as potential host/guest sensing layers for detecting selected ions in dilute aqueous solutions using single microcantilever experimental system. In this work it was shown that modifying the upper rim of the calix[4]arenes with a thioacetate end group allow calix[4]arenes to self-assemble on Au(111) forming complete highly ordered monolayers. It was also found that incubating the microcantilevers coated with 5 nm of Inconel and 40 nm of Au for 1 h in a 1.0 M solution of calix[4]arene produced the highest sensitivity. Methoxy-functionalized microcantilevers showed a definite preference for Ca²⁺ ions over other cationic guests and were able to detect trace concentration as low as 10⁻¹² M in aqueous solutions. Microcantilevers modified with ethoxy calix[4]arene displayed their highest sensitivity towards Sr²⁺ and to a lesser extent Ca²⁺ ions. Crown calix[4]arene-modified microcantilevers were however found to bind selectively towards Cs⁺ ions. In addition, the counter anion was also found to contribute to the deflection. For example methoxy calix[4]arene-modified microcantilever was found to be more sensitive to CaCl₂ over other water-soluble calcium salts such as Ca(NO₃)₂ , CaBr₂ and CaI₂. These findings suggest that the response of calix[4]arene-modified microcantilevers should be attributed to the target ionic species as a whole instead of only considering the specific cation and/or anion. Part II presents the development of a 16-microcantilever sensor setup. The implementation of this system involved the creation of data analysis software that incorporates data from the motorized actuator and a two-axis photosensitive detector to obtain the deflection signal originating from each individual microcantilever in the array. The system was shown to be capable of simultaneous measurements of multiple microcantilevers with different coatings. A functionalization unit was also developed that allows four microcantilevers in the array to be coated with an individual sensing layer one at the time. Because of the variability of the spring constants of different cantilevers within the array, results presented were quoted in units of surface stress unit in order to compare values between the microcantilevers in the array.

A Delay Vector Variance based marker for an output-only assessment of structural changes in tension leg platforms

Although aspects of power generation of many offshore renewable devices are well understood, their dynamic responses under high wind and wave conditions are still to be investigated to a great detail. Output only statistical markers are important for these offshore devices, since access to the device is limited and information about the exposure conditions and the true behaviour of the devices are generally partial, limited, and vague or even absent. The markers can summarise and characterise the behaviour of these devices from their dynamic response available as time series data. The behaviour may be linear or nonlinear and consequently a marker that can track the changes in structural situations can be quite important. These markers can then be helpful in assessing the current condition of the structure and can indicate possible intervention, monitoring or assessment. This paper considers a Delay Vector Variance based marker for changes in a tension leg platform tested in an ocean wave basin for structural changes brought about by single column dampers. The approach is based on dynamic outputs of the device alone and is based on the estimation of the nonlinearity of the output signal. The advantages of the selected marker and its response with changing structural properties are discussed. The marker is observed to be important for monitoring the as- deployed structural condition and is sensitive to changes in such conditions. Influence of exposure conditions of wave loading is also discussed in this study based only on experimental data.

Comparison of two methods for measuring the pubococcygeal line from sagittal-plane magnetic resonance imaging

Aims The pubococcygeal line (PCL) is an important reference line for determining measures of pelvic organ support on sagittal-plane magnetic resonance imaging (MRI); however, there is no consensus on where to place the posterior point of the PCL. As coccyx movement produced during pelvic floor muscle (PFM) contractions may affect other measures, optimal placement of the posterior point is important. This study compared two methods for measuring the PCL, with different posterior points, on T2-weighted sagittal MRI to determine the effect of coccygeal movement on measures of pelvic organ support in older women. Methods MRI of the pelvis was performed in the midsagittal plane, at rest and during PFM contractions, on 47 community-dwelling women 60 and over. The first PCL was measured to the tip of the coccyx (PCLtip) and the second to the sacrococcygeal joint (PCLjnt). Four measures of pelvic organ support were made using each PCL as the reference line: urethrovesical junction height, uterovaginal junction height, M-line and levator plate angle. Results During the PFM contraction the PCLtip shortened and lifted (P < 0.001); the PCLjnt did not change (P > 0.05). The changes in the four measures of pelvic organ support were smaller when measured relative to the PCLtip as compared to those to the PCLjnt (P < 0.001). Conclusions Coccyx movement affected the length and position of the PCLtip, which resulted in underestimates of the pelvic-organ lift produced by the PFM contraction. Therefore, we recommend that the PCL be measured to the sacrococcygeal joint and not to the tip of the coccyx

Damaging effects of advanced glycation end product in the murine macrophages cell line J774A.1.

The interaction of reducing sugars, such as aldose, with proteins and the subsequent molecular rearrangements, produces irreversible advanced glycation end-products (AGEs), a heterogeneous class of non-enzymatic glycated proteins or lipids. AGEs form cross-links, trap macromolecules and release reactive oxygen intermediates. AGEs are linked to aging, and increase in several related diseases. The aim of this study was to assess, in a murine macrophage cell line, J774A.1, the effects of 48 h of exposure to glycated serum containing a known amount of pentosidine, a well-known AGE found in the plasma and tissues of diabetic and uremic subjects. Fetal bovine serum was incubated with ribose (50 mm) for 7 days at 37 °C to obtain about 10 nmol/ml of pentosidine. The cytotoxic parameters studied were cell morphology and viability by neutral red uptake, lactate dehydrogenase release and tetrazolium salt test. In the medium and in the intracellular compartment, bound and free pentosidine were evaluated by HPLC, as sensitive and specific glycative markers, and thiobarbituric acid reactive substances (TBARs), as index of the extent of lipid peroxidation. Our results confirm that macrophages are able to take up pentosidine. It is conceivable that bound pentosidine is degraded and free pentosidine is released inside the cell and then into the medium. The AGE increase in the medium was combined with an increase in TBARs, meaning that an oxidative stress occurred; marked cytotoxic effects were observed, and were followed by the release of free pentosidine and TBARs into the culture medium.

What's in it for us? A case study research about micro sense making processes through the eyes of front line employees, during culture change implementation

Abstract How employees make sense of change is a very complex process. Recently, academics have neglected to research sense making activities in a micro culture implementation context, through the eyes of front line employees. In contrast to a macro view, a micro perspective limits researchers to only look at an individual, departmental or group level. By doing so, we can zoom in on the details of sense making processes that employees use in their daily work life. A macro (organisational) view is based on the notion that there is a general integrated culture that can be found in all organisational units and departments. It is assumed that culture can be researched by using the entire organisation as one single research entity. This thesis challenges this assumption. In case of planned change it is usually the management community who are in charge of the change intervention. Because of their formal hierarchical position, they have the power to abort or initiate change programs. It is perhaps therefore that researchers tend to be focused on the management community rather than on lower level organisational members, such as front line employees. Apart from the micro view, scholars also neglected to research culture change implementation through the eyes of front line employees. This thesis is an attempt to fill these two gaps that currently exists in academic change management publications. The main research question is therefore: From a micro point of view how do front-line employees make sense of the impact of culture change, during the implementation phase? This thesis starts with a literature review which exposes the two main gaps. The most important outcome of this review is that only 2% of the research articles dealt with culture implementation, through the eyes of front line employees. A conceptual research model is built on the integrated sense making theory of Weber and Manning (2001) and the micro variables of Raelin and Cataldo (2011). These theories emphasize elements of sense making in a daily working context. It is likely that front line employees can identify themselves with research elements such as tasks, skills practices, involvement and behaviour. Front line employees were selected, because as lower level organisational members they are usually the change recipients. They are further away from the change initiating scene (usually the management of an organisation) and form a potential sense making ‘hotspot’ that could provide new academic insights. In order to carry out the primary research, two case organisations were selected in the leisure industry. A participative case study research method was chosen. This meant that the researcher worked in the concerning departments of the case organisations. The goal was to observe and interview front line employees, while they were performing their jobs. The most important advantage of this approach is that the researcher temporarily becomes one with the organisation and is therefore able to acquire both formal and informal narratives that front line employees use during sense making activities. It was found that front line employees make sense of organisational change by using a practical approach. They make sense of the change program by carrying out new tasks, developing new skills and sharing best practices. The most noticeable conclusion was that sense making activities predominantly take place at an individual level in relation to change acceptance. Organisational members tend to create a mental equation in order to weigh the advantages against the disadvantages. They evaluate whether the concerning change program is beneficial to them or not. For future research a sense making scheme model is suggested that is based on two methods: an introspection and an action method.

p.(L576P) -KIT mutation in GIST: Favorable prognosis and sensitive to imatinib?

Exon 11 KIT mutations are found in a majority of gastrointestinal stromal tumors (GIST) and are usually predictive of response to imatinib, a KIT, PDGFRA and ABL inhibitor. Exon 11 mutations with poor sensitivity to imatinib and poor outcome can be observed on rare occasions, including p.(L576P). In silico and in vitro studies suggested a decreased binding affinity for imatinib in p.(L576P) KIT mutations, thereby offering an explanation for their poor outcome and poor response to standard therapy. These observations were further corroborated with anecdotal case reports of refractoriness or non-durable response to imatinib therapy. However, we describe the favorable response to imatinib and outcome in 5 p.(L576P)-KIT mutant GIST patients treated at a tertiary sarcoma referral center. The sensitivity of p.(L576P)-KIT mutations to imatinib, and the prognostic impact of this mutation need to be further evaluated in a larger cohort. Based on our observations, p.(L576P) mutated GISTs should be treated with standard first line imatinib therapy.

Identifying the Impact of Incomplete Datasets on Process Cycle Time Prediction in an Aerospace Assembly Line

Supply Chain Simulation (SCS) is applied to acquire information to support outsourcing decisions but obtaining enough detail in key parameters can often be a barrier to making well informed decisions.
One aspect of SCS that has been relatively unexplored is the impact of inaccurate data around delays within the SC. The impact of the magnitude and variability of process cycle time on typical performance indicators in a SC context is studied.
System cycle time, WIP levels and throughput are more sensitive to the magnitude of deterministic deviations in process cycle time than variable deviations. Manufacturing costs are not very sensitive to these deviations.
Future opportunities include investigating the impact of process failure or product defects, including logistics and transportation between SC members and using alternative costing methodologies.

Highway Performance and Time-Sensitive Industries, 1998

This report addresses delays to freight shippers. Although the focus is on just-in-time (JIT) businesses, the authors also note that non JIT businesses also suffer delays that impact their productivity. The table of contents lists the following headings: chapter 1 - introduction - a trial application: the Des Moines metropolitan area; structure of the report; chapter 2 - reliability at the forefront of freight transport demand - manufacturing and inventory; just-in-time operations in the U.S.; transportation consequences; summary; chapter 3 - JIT operations in Iowa - survey and sample; trucking activity and service; just-in-time truck transportation in Iowa; assessment of factors affecting truck transportation service; summary and conclusions; chapter 4 - travel time uncertainty induced by incidents - a probabilistic model for incident occurrences and durations; calculation of delay; trial application; conclusions; and chapter 5 - conclusions and recommendations - conclusions; recommendations.

Tests of a silica aerogel cerenkov detector to be used in the european hybrid spectrometer

An 18 module Ceienkov detector with a total sensitive area of 2.3 m2 having silica aerogel as radiator is being tested in a particle beam at CERN PS. The modules having a sensitive area of 23 X 55 cm2 give typically a Cerenkov signal for (3= 1 particles of 12 photoelectrons for silica aerogel of refractive index 1.03 and a thickness of 15 cm. © 1981 IOP Publishing Ltd.

Optimization of a multielectrode array (MEA)-based approach to study the impact of Aβ on the SH-SY5Y cell line

The human brain stores, integrates, and transmits information recurring to millions of neurons, interconnected by countless synapses. Though neurons communicate through chemical signaling, information is coded and conducted in the form of electrical signals. Neuroelectrophysiology focus on the study of this type of signaling. Both intra and extracellular approaches are used in research, but none holds as much potential in high-throughput screening and drug discovery, as extracellular recordings using multielectrode arrays (MEAs). MEAs measure neuronal activity, both in vitro and in vivo. Their key advantage is the capability to record electrical activity at multiple sites simultaneously. Alzheimer’s disease (AD) is the most common neurodegenerative disease and one of the leading causes of death worldwide. It is characterized by neurofibrillar tangles and aggregates of amyloid-β (Aβ) peptides, which lead to the loss of synapses and ultimately neuronal death. Currently, there is no cure and the drugs available can only delay its progression. In vitro MEA assays enable rapid screening of neuroprotective and neuroharming compounds. Therefore, MEA recordings are of great use in both AD basic and clinical research. The main aim of this thesis was to optimize the formation of SH-SY5Y neuronal networks on MEAs. These can be extremely useful for facilities that do not have access to primary neuronal cultures, but can also save resources and facilitate obtaining faster high-throughput results to those that do. Adhesion-mediating compounds proved to impact cell morphology, viability and exhibition of spontaneous electrical activity. Moreover, SH-SY5Y cells were successfully differentiated and demonstrated acute effects on neuronal function after Aβ addition. This effect on electrical signaling was dependent on Aβ oligomers concentration. The results here presented allow us to conclude that the SH-SY5Y cell line can be successfully differentiated in properly coated MEAs and be used for assessing acute Aβ effects on neuronal signaling.

Comparison of two methods for measuring the pubococcygeal line from sagittal-plane magnetic resonance imaging

Aims The pubococcygeal line (PCL) is an important reference line for determining measures of pelvic organ support on sagittal-plane magnetic resonance imaging (MRI); however, there is no consensus on where to place the posterior point of the PCL. As coccyx movement produced during pelvic floor muscle (PFM) contractions may affect other measures, optimal placement of the posterior point is important. This study compared two methods for measuring the PCL, with different posterior points, on T2-weighted sagittal MRI to determine the effect of coccygeal movement on measures of pelvic organ support in older women. Methods MRI of the pelvis was performed in the midsagittal plane, at rest and during PFM contractions, on 47 community-dwelling women 60 and over. The first PCL was measured to the tip of the coccyx (PCLtip) and the second to the sacrococcygeal joint (PCLjnt). Four measures of pelvic organ support were made using each PCL as the reference line: urethrovesical junction height, uterovaginal junction height, M-line and levator plate angle. Results During the PFM contraction the PCLtip shortened and lifted (P < 0.001); the PCLjnt did not change (P > 0.05). The changes in the four measures of pelvic organ support were smaller when measured relative to the PCLtip as compared to those to the PCLjnt (P < 0.001). Conclusions Coccyx movement affected the length and position of the PCLtip, which resulted in underestimates of the pelvic-organ lift produced by the PFM contraction. Therefore, we recommend that the PCL be measured to the sacrococcygeal joint and not to the tip of the coccyx

The New Bottom Line: Black Women Cultural Entrepreneurs Re-Define Success in The Connected Economy

Black women cultural entrepreneurs are a group of entrepreneurs that merit further inquiry. Using qualitative interview and participant observation data, this dissertation investigates the ways in which black women cultural entrepreneurs define success. My findings reveal that black women cultural entrepreneurs are a particular interpretive community with values, perspectives and experiences, which are not wholly idiosyncratic, but shaped by collective experiences and larger social forces. Black women are not a monolith, but they are neither disconnected individuals completely devoid of group identity. The meaning they give to their businesses, professional experiences and understandings of success are influenced by their shared social position and identity as black women. For black women cultural entrepreneurs, the New Bottom Line goes beyond financial gain. This group, while not uniform in their understandings of success, largely understand the most meaningful accomplishments they can realize as social impact in the form of cultural intervention, black community uplift and professional/creative agency. These particular considerations represent a new paramount concern, and alternative understanding of what is typically understood as the bottom line. The structural, social and personal challenges that black women cultural entrepreneurs encounter have shaped their particular perspectives on success. I also explore the ways research participants articulated an oppositional consciousness to create an alternative means of defining and achieving success. I argue that this consciousness empowers them with resources, connections and meaning not readily conferred in traditional entrepreneurial settings. In this sense, the personal, social and structural challenges have been foundational to the formation of an alternative economy, which I refer to as The Connected Economy. Leading and participating in The Connected Economy, black women cultural entrepreneurs represent a black feminist and womanist critique of dominant understandings of success.

Cold vapour generation electrothermal atomic absorption spectrometry and solid phase extraction based on a new nanosorbent for sensitive HG determination in environmental samples (sea water and river water)

Mercury is not an essential element for plant or animal life and it is a potential environmental toxic because of its tendency to form covalent bonds with organic molecules and the high stability of the Hg-C bond. Reports estimate a total mercury concentration in natural waters ranging from 0.2 to 100 ng L-1. Due to this fact, highly sensitive methods are required for direct determination of such extremely low levels. In this work, a rapid and simple method was developed for separation and preconcentration of mercury by flow injection solid phase extraction coupled with on-line chemical vapour generation electrothermal atomic absorption spectrometry. The system is based on chelating retention of the analyte onto the mini column filled with a mesoporous silica functionalized with 1,5 bis (di-2-pyridyl) methylene thiocarbohydrazide. The main aim of this work was to develop a precise and accurate method for the determination of the Hg. Under the optima conditions and 120 s preconcentration time, the detection limit obtained was 0.009 μg L-1, with RSDs 3.7 % for 0.2 μg L-1, 4.8 % for 1 μg L-1 and enrichment factor 4, Furthermore, the method proposed has permitted the determination of Hg with a reduction in the analysis time, the sample throughput was about 18 h-1, low consumption of reagents and sample volume. The method was applied to the determination of Hg in sea water and river water. For the quality control of the analytical performance and the validation of the newly developed method, the analysis of two certified samples, TMDA 54.4 Fortified Lake, and LGC6187 River sediment was addressed. The results showed good agreement with the certified values.

Study of new physiological characteristics as protein receptors (RP55) of light, color, heat, motion, smell, electric, vibration and position located in head, body and abdominal, found in mosquito larvae.

The main objective of the research is to demonstrate new physiological characteristics receptors in the presence of mosquito larvae. 100 larvae of different species were collected and studied for a week in periods of 8-24 hrs. Larvae stages I, II, III and IV have photo-thermo receptors of light and heat housed in the body is divided into head, thorax and abdomen, perceive hot or cold environments, and have fibers in chest or hairs lining your body or abdomen, and a pair of antennae on the head. Stages II and III are more developed than the initial stages. They are attracted by the dark green at the bottom, a pair of eyes that perceive light and color. Have receptors proteins (RP55) that capture motion at a speed the slightest movement of waves in the water. Its nose is not well developed but have chemoreceptors. They adapt to changes in pH in alkaline media, are sensitive to chemical, thermal and mechanical changes nociceptors have electroreceptors or galvanoreceptores sensitive to electrical stimuli, have mechanoreceptors that are sensitive to touch, pain, pressure, gravity, sound. They have a GPS position that seems the guides. It is precisely in the fibers, mushrooms or bristles are recipients along with the micro villi in head, thorax and abdomen.
RESUMEN El objetivo principal de la investigación es demostrar nuevas características fisiológicas como la presencia de receptores en las larvas de mosquitos. Se recolectaron 100 larvas de diferentes especies y se estudiaron por una semana en periodos de 8 a 24 hrs. Las larvas de los estadios I,II,III y IV tienen foto-termo receptores de luz y calor alojados en el cuerpo que se divide en cabeza, tórax y abdomen, perciben ambientes fríos o calientes, así como tienen fibras en tórax o pelos que recubren su cuerpo, y un par de antenas en la cabeza. Los estadios II y III son más desarrollados que las etapas iniciales. Tienen receptores proteicos RP55. Les atrae el color verde oscuro en el fondo, un par de ojos que perciben la luz y color con fotoreceptores. Tienen receptores RP55 de movimiento que captan a una velocidad el más mínimo movimiento de ondas en el agua. Su olfato no está muy desarrollado pero tienen quimioreceptores. Se adaptan a cambios de pH en medios alcalinos, tienen nociceptores sensibles a cambios químicos, térmicos y mecánicos, tienen galvanoreceptores o electroreceptores sensibles a estímulos eléctricos, tienen mecanoreceptores que son sensibles al tacto, dolor, presión gravedad, sonido. Tienen un GPS de posición que pareciera las orienta.

Nanosecond-level time synchronization of autonomous radio detector stations for extensive air showers

To exploit the full potential of radio measurements of cosmic-ray air showers at MHz frequencies, a detector timing synchronization within 1 ns is needed. Large distributed radio detector arrays such as the Auger Engineering Radio Array (AERA) rely on timing via the Global Positioning System (GPS) for the synchronization of individual detector station clocks. Unfortunately, GPS timing is expected to have an accuracy no better than about 5 ns. In practice, in particular in AERA, the GPS clocks exhibit drifts on the order of tens of ns. We developed a technique to correct for the GPS drifts, and an independent method is used to cross-check that indeed we reach a nanosecond-scale timing accuracy by this correction. First, we operate a "beacon transmitter" which emits defined sine waves detected by AERA antennas recorded within the physics data. The relative phasing of these sine waves can be used to correct for GPS clock drifts. In addition to this, we observe radio pulses emitted by commercial airplanes, the position of which we determine in real time from Automatic Dependent Surveillance Broadcasts intercepted with a software-defined radio. From the known source location and the measured arrival times of the pulses we determine relative timing offsets between radio detector stations. We demonstrate with a combined analysis that the two methods give a consistent timing calibration with an accuracy of 2 ns or better. Consequently, the beacon method alone can be used in the future to continuously determine and correct for GPS clock drifts in each individual event measured by AERA.