Stress intensity factor threshold in dental porcelains

The stress intensity factor threshold (K(IO)) is related to the stress level at which cracks start to grow stably, causing the weakening of porcelain prostheses during their use. The values of K(IO) of seven dental porcelains (with and without reinforcing leucite crystal, KAlSi(2)O(6)) stored in air (22 degrees C, 60% relative humidity) and artificial saliva (37 degrees C) were determined by measuring the crack growth velocity of radial cracks generated at the corner of Vickers indentations. The results of K(IO) were correlated with the leucite content, fracture toughness (K(Ic)), and chemical composition of the porcelains. It was observed that K(IO) increased with the increase of leucite content (only for the leucite-based porcelains) and with the increase of K(Ic). The increase in Al(2)O(3) content or the decrease in the alkali oxide (K(2)O and Na(2)O) content of the material`s glassy matrix tended to increase the K(IO) values. Storage media (air and saliva) did not significantly affect the K(IO) of porcelains tested, indicating that the control parameter of K(IO) value was not the water content of the storage media.

Star decompositions of cubes

Let Sk denote the complete bipartite graph K-1k and let e,, denote the ii-cube. We prove that the obvious necessary conditions for the existence of an S-k-decomposition of Q(n) are sufficient.

Star factorizations of graph products

A k-star is the graph K-1,K-k. We prove a general theorem about k-star factorizations of Cayley graphs. This is used to give necessary and sufficient conditions for the existence of k-star factorizations of any power (K-q)(S) of a complete graph with prime power order q, products C-r1 x C-r2 x ... x C-rk of k cycles of arbitrary lengths, and any power (C-r)(S) of a cycle of arbitrary length. (C) 2001 John Wiley & Sons, Inc.

Field test of a model of migration of moths (Lepidoptera : Noctuidae) in inland Australia

A migration of Helicoverpa punctigera (Wallengren), Heliothis punctifera (Walker) and Agrotis munda Walker was tracked from Cameron Corner (29degrees00'S, 141degrees00'E) in inland Australia to the Wilcannia region, approximately 400 km to the south-east. A relatively isolated source population was located using a distribution model to predict winter breeding, and confirmed by surveys using sweep netting for larvae. When a synoptic weather pattern likely to produce suitable conditions for migration developed, moths were trapped in the source region. The next morning a simulation model of migration using wind-field data generated by a numerical weather-prediction model was run. Surveys using sweep netting for larvae, trapping and flush counts were then conducted in and around the predicted moth fallout area, approximately 400 km to the south-east. Pollen carried on the probosces of moths caught in this area was compared with that on moths caught in the source area. The survey data and pollen comparisons provided evidence that migration had occurred, and that the migration model gave accurate estimation of the fallout region. The ecological and economic implications of such migrations are discussed.

Precipitation hardening of Cu-Fe-Cr alloys - Part I - Mechanical and electrical properties

This research is part of a project whose scope was to investigate the engineering properties of new non-commercial alloy formulations based on the Cu rich corner of the Cu-Fe-Cr ternary system with the primary aim of exploring the development of a new cost-effective high-strength, high-conductivity copper alloy. The literature indicated that Cu rich Cu-Cr and Cu-Fe alloys have been thoroughly investigated. A number of commercial alloys have been developed and these are used for a variety of applications requiring combinations of high-strength, high-conductivity and resistance to softening. Little evidence was found in the literature that the Cu rich corner of the Cu-Fe-Cr system had previously been investigated for the purpose of developing high-strength, high-conductivity copper alloys resistant to softening. The aim of these present investigations was to explore the possibility that new alloys could be developed that combined the properties of both sets of alloys, ie large precipitation hardening response combined with the ability to stabilise cold worked microstructures to high temperatures while at the same maintain high electrical conductivity. To assess the feasibility of this goal the following alloys were chosen for investigation: Cu-0.7wt%Cr-0.3wt%Fe, Cu-0.7wt%Cr-0.8wt%Fe, Cu-0.7wt%Cr-2.0wt%Fe. This paper reports on the mechanical property investigation which indicated that the Cu-0.7wt%Cr-0.3wt%Fe, and Cu-0.7wt%Cr-2.0wt%Fe alloys were worthy of further investigation. (C) 2001 Kluwer Academic Publishers.

Precipitation hardening of Cu-Fe-Cr alloys - Part II - Microstructural characterisation

This research is part of a project whose scope was to investigate the engineering properties of new non-commercial alloy formulations based on the Cu rich corner of the Cu-Fe-Cr ternary system with the primary aim of exploring the development of a new cost-effective high-strength, high-conductivity copper alloy. Promising properties have been measured for the following alloys: Cu-0.7wt%Cr-0.3wt%Fe and Cu-0.7wt%Cr-2.0wt%Fe. This paper reports on the microstructural characterisation of these alloys and discusses the mechanical and electrical properties of these alloys in terms of their microstructure, particularly the formation of precipitates. These alloys have evinced properties that warrant further investigation. Cost modelling has shown that Cu-0.7wt%Cr-0.3wt%Fe is approximately 25% cheaper to produce than commercial Cu-1%Cr. It has also been shown to be more cost efficient on a yield stress and % IACS per dollar basis. The reason for the cost saving is that the Cu-0.7%Cr-0.3%Fe alloy can be made with low carbon ferro-chrome additions as the source of chromium rather than the more expensive Cu-Cr master-alloy. For applications in which cost is one of the primary materials selection criteria, it is envisaged that there would be numerous applications in both cast and wrought form, where the Cu-0.7%Cr-0.3%Fe alloy would be more suitable than Cu-1%Cr. (C) 2001 Kluwer Academic Publishers.

Quaternary Cu-0.7%Cr-0.3%Fe-X alloys

This research is part of a project whose scope was to investigate the engineering properties of new non-commercial alloy formulations based on the Cu rich corner of the Cu-Fe-Cr ternary system with the primary aim of exploring the development of a new cost-effective high-strength, high-conductivity copper alloy. The aim of the present work was to increase the electrical conductivity and strength of the Cu-0.7wt%Cr-0.3wt%Fe alloy through selective minor additions (less than or equal to0.15 wt%) of elements expected to promote precipitation of dissolved Fe: Ti, B, P, Ni & Y. Such quaternary alloys with reduced Fe in solid solution would be expected to have properties equivalent to or better than those of the Cu-1%Cr reference alloy (Alloy Z). The investigation showed that none of the trace element additions significantly improved the size of the age hardening response or the peak aged electrical conductivity of Alloy A, although further work is required on the influence of Ti. Additions of P and B were detrimental. Other trace additions had little or no effect apart from causing some slight changes to the precipitation kinetics. The mechanical properties of the Cu-0.7%Cr-0.3%Fe alloy made with less expensive high carbon ferrochrome were found to be inferior to those of the equivalent alloy made with low carbon ferrochrome. (C) 2001 Kluwer Academic Publishers.

Heat transfer and flow behind a step in high enthalpy superorbital flow

Heat transfer levels have been investigated behind a rearward-facing step in a superorbital expansion tube. The heat transfer was measured along a flat plate and behind 2 and 3mm steps with the same length to step height ratio. Results were obtained with air as the test gas at speeds of 6.76kms(-1) and 9-60kms(-1) corresponding to stagnation enthalpies of 26MJ/kg and 48MJ/kg respectively. A laminar boundary layer was established on the flat plate and measured heat transfer levels were consistent with classical empirical correlations. In the case of flow behind a step, the measurements showed a gradual rise in heat transfer from the rear of the step to a plateau several step heights downstream for both flow conditions. Reattachment distance was estimated to be approximately 1.6 step heights downstream of the 2mm step at the low enthalpy condition through the use of flow visualisation.

Biaxial failure model for fiber reinforced concrete

Steel fiber reinforced concrete (SFRC) is widely applied in the construction industry. Numerical elastoplastic analysis of the macroscopic behavior is complex. This typically involves a piecewise linear failure curve including corner singularities. This paper presents a single smooth biaxial failure curve for SFRC based on a semianalytical approximation. Convexity of the proposed model is guaranteed so that numerical problems are avoided. The model has sufficient flexibility to closely match experimental results. The failure curve is also suitable for modeling plain concrete under biaxial loading. Since this model is capable of simulating the failure states in all stress regimes with a single envelope, the elastoplastic formulation is very concise and simple. The finite element implementation is developed to demonstrate the conciseness and the effectiveness of the model. The computed results display good agreement with published experimental data.

Design of improved rail-to-rail low-distortion and low-stress switches in advanced CMOS technologies

This paper describes the efficient design of an improved and dedicated switched-capacitor (SC) circuit capable of linearizing CMOS switches to allow SC circuits to reach low distortion levels. The described circuit (SC linearization control circuit, SLC) has the advantage over conventional clock-bootstrapping circuits of exhibiting low-stress, since large gate voltages are avoided. This paper presents exhaustive corner simulation results of a SC sample-and-hold (S/H) circuit which employs the proposed and optimized circuits, together with the experimental evaluation of a complete 10-bit ADC utilizing the referred S/H circuit. These results show that the SLC circuits can reduce distortion and increase dynamic linearity above 12 bits for wide input signal bandwidths.

CrimsonHex: a service oriented repository of specialised learning objects

The corner stone of the interoperability of eLearning systems is the standard definition of learning objects. Nevertheless, for some domains this standard is insufficient to fully describe all the assets, especially when they are used as input for other eLearning services. On the other hand, a standard definition of learning objects in not enough to ensure interoperability among eLearning systems; they must also use a standard API to exchange learning objects. This paper presents the design and implementation of a service oriented repository of learning objects called crimsonHex. This repository is fully compliant with the existing interoperability standards and supports new definitions of learning objects for specialized domains. We illustrate this feature with the definition of programming problems as learning objects and its validation by the repository. This repository is also prepared to store usage data on learning objects to tailor the presentation order and adapt it to learner profiles.

An Approach To Publish a Data Warehouse Content as Linked Data

Mestrado em Engenharia Informática - Área de Especialização em Tecnologias do Conhecimento e Decisão

Ambientes Tridimensionais Sonoros

O estado emocional de um individuo tem um papel importante na realização de determinada tarefa, ou conjunto de tarefas, na medida em que pode influenciar o bom desempenho na realização destas. O ser humano pode sentir diversas emoções e, conjugadas, resultam em inúmeros estados emocionais. A música pode influenciar o nosso estado emocional, mesmo de uma forma inconsciente. Por isso ouvimos música enquanto realizamos várias tarefas. O foco desta dissertação consistiu na criação de uma ferramenta multimédia – EMOCUBE (emotion cube – caixa de emoções) que, através da música, contribuísse para o sucesso da realização de determinada tarefa/situação. A cada situação é atribuído um estado emocional, que influenciará a seleção das músicas sugeridas ao ouvinte. Os resultados da avaliação efetuada sobre a aplicação foram, de uma forma geral, positivos e salientaram a originalidade da ideia deste projeto. Com o desenvolvimento desta aplicação, abriram-se portas para novos projetos e possíveis parcerias com ferramentas e aplicações já existentes no mercado.

Cold Urticaria and Infectious Mononucleosis in Children

Physical urticaria includes a heterogeneous group of disorders characterized by the development of urticarial lesions and/or angioedema after exposure to certain physical stimuli. The authors present the case of a child with severe acquired cold urticaria secondary to infectious mononucleosis. Avoidance of exposure to cold was recommended; prophylactic treatment with ketotifen and cetirizine was begun and a self-administered epinephrine kit was prescribed. The results of ice cube test and symptoms significantly improved. Physical urticaria, which involves complex pathogenesis, clinical course and therapy, may be potentially life threatening. Evaluation and diagnosis are especially important in children. To our knowledge this is the first description of persistent severe cold-induced urticaria associated with infectious mononucleosis in a child.

Navegação web anónima e segura

A Web aproximou a humanidade dos seus pares a um nível nunca antes visto. Com esta facilidade veio também o cibercrime, o terrorismo e outros fenómenos característicos de uma sociedade tecnológica, plenamente informatizada e onde as fronteiras terrestres pouco importam na limitação dos agentes ativos, nocivos ou não, deste sistema. Recentemente descobriu-se que as grandes nações “vigiam” atentamente os seus cidadãos, desrespeitando qualquer limite moral e tecnológico, podendo escutar conversas telefónicas, monitorizar o envio e receção de e-mails, monitorizar o tráfego Web do cidadão através de poderosíssimos programas de monitorização e vigilância. Noutros cantos do globo, nações em tumulto ou envoltas num manto da censura perseguem os cidadãos negando-lhes o acesso à Web. Mais mundanamente, há pessoas que coagem e invadem a privacidade de conhecidos e familiares, vasculhando todos os cantos dos seus computadores e hábitos de navegação. Neste sentido, após o estudo das tecnologias que permitem a vigilância constante dos utilizadores da Web, foram analisadas soluções que permitem conceder algum anónimato e segurança no tráfego Web. Para suportar o presente estudo, foi efetuada uma análise das plataformas que permitem uma navegação anónima e segura e um estudo das tecnologias e programas com potencial de violação de privacidade e intrusão informática usados por nações de grande notoriedade. Este trabalho teve como objetivo principal analisar as tecnologias de monitorização e de vigilância informática identificando as tecnologias disponíveis, procurando encontrar potenciais soluções no sentido de investigar a possibilidade de desenvolver e disponibilizar uma ferramenta multimédia alicerçada em Linux e em LiveDVD (Sistema Operativo Linux que corre a partir do DVD sem necessidade de instalação). Foram integrados recursos no protótipo com o intuito de proporcionar ao utilizador uma forma ágil e leiga para navegar na Web de forma segura e anónima, a partir de um sistema operativo (SO) virtualizado e previamente ajustado para o âmbito anteriormente descrito. O protótipo foi testado e avaliado por um conjunto de cidadãos no sentido de aferir o seu potencial. Termina-se o documento com as conclusões e o trabalho a desenvolver futuramente.