Soil spectral library and its use in soil classification

Soil science has sought to develop better techniques for the classification of soils, one of which is the use of remote sensing applications. The use of ground sensors to obtain soil spectral data has enabled the characterization of these data and the advancement of techniques for the quantification of soil attributes. In order to do this, the creation of a soil spectral library is necessary. A spectral library should be representative of the variability of the soils in a region. The objective of this study was to create a spectral library of distinct soils from several agricultural regions of Brazil. Spectral data were collected (using a Fieldspec sensor, 350-2,500 nm) for the horizons of 223 soil profiles from the regions of Matão, Paraguaçu Paulista, Andradina, Ipaussu, Mirandópolis, Piracicaba, São Carlos, Araraquara, Guararapes, Valparaíso (SP); Naviraí, Maracajú, Rio Brilhante, Três Lagoas (MS); Goianésia (GO); and Uberaba and Lagoa da Prata (MG). A Principal Component Analysis (PCA) of the data was then performed and a graphic representation of the spectral curve was created for each profile. The reflectance intensity of the curves was principally influenced by the levels of Fe2O3, clay, organic matter and the presence of opaque minerals. There was no change in the spectral curves in the horizons of the Latossolos, Nitossolos, and Neossolos Quartzarênicos. Argissolos had superficial horizon curves with the greatest intensity of reflection above 2,200 nm. Cambissolos and Neossolos Litólicos had curves with greater reflectance intensity in poorly developed horizons. Gleisols showed a convex curve in the region of 350-400 nm. The PCA was able to separate different data collection areas according to the region of source material. Principal component one (PC1) was correlated with the intensity of reflectance samples and PC2 with the slope between the visible and infrared samples. The use of the Spectral Library as an indicator of possible soil classes proved to be an important tool in profile classification.

Human alveolar macrophages infected by virulent bacteria expressing SipB are a major source of active interleukin-18.

Recent publications have demonstrated that the protease caspase-1 is responsible for the processing of pro-interleukin 18 (IL-18) into the active form. Studies on cell lines and murine macrophages have shown that the bacterial invasion factor SipB activates caspase-1, triggering cell death. Thus, we investigated the role of SipB in the activation and release of IL-18 in human alveolar macrophages (AM), which are the first line of defense against inhaled pathogens. Under steady-state conditions, AM are a more important source of IL-18 than are dendritic cells (DC) and monocytes. Cytokine production by AM and DC was compared after both types of cells had been infected with a virulent strain of Salmonella enterica serovar Typhimurium and an isogenic sipB mutant, which were used as an infection model. Infection with virulent Salmonella led to marked cell death with features of apoptosis while both intracellular activation and release of IL-18 were demonstrated. In contrast, the sipB mutant did not induce such cell death or the release of active IL-18. The specific caspase-1 inhibitor Ac-YVAD-CMK blocked the early IL-18 release in AM infected with the virulent strain. However, the type of Salmonella infection did not differentially regulate IL-18 gene expression. We concluded that the bacterial virulence factor SipB plays an essential posttranslational role in the intracellular activation of IL-18 and the release of the cytokine in human AM.

Wasps (Insecta: Vespida=Hymenoptera) from the Early Cretaceous of Spain.

Wasps and their relatives from the Lower Cretaceous lithographic limestones of Spain have been studied. Thirty specimens representing 30 species (4 of them with undetermined placement), at least 21 genera and 11 families are recorded. We erect 1 new family - Andrenelidae-, 6 new genera and 11 new species: Meiaghilarella cretacica n.gen., n.sp. (Sepulcidae Ghilarellinae), Eosyntexis catalonicus n.sp., Cretosyntexis montsecensis n.gen., n.sp. (Anaxyelidae Syntexinae), Montsecephialtites zherikhini n.gen., n.sp. (Ephialtitidae Ephialtitinae), Karataus hispanicus n.sp. (Ephialtitidae Symphytopterinae), Manlaya ansorge i n.sp. (Gasteruptiidae Baissinae), Andrenelia pennata n.gen., n.sp. (Andrenelidae n. fam.), Cretoserphus gomezi n.gen., n.sp. (Mesoserphidae), Montsecosphex jarzembow skii n.gen., n.sp., Angarosphex penyalveri n.sp., Pompilopterus (?) noguerensis n.sp. (Sphecidae Angarosphecinae), Cretoscolia conquensis n.sp. (Scoliidae Archaeoscoliinae). The Mesozoic family Ephialtitidae is revisited based on the restudy of the type-species. We compare these Spanish Cretaceous assemblages with other ones from various parts of the world: Central and Eastern Asia, England, Australia, and Brazil. The number of genera and families identified in the Spanish fossil-sites is almost the same as in the English Purbeck and Wealden. The absence of some hymenopteran groups as Xyelidae, is consistent with the warm climate know to exist in Spain during the Early Cretaceous. We conclude that both La Cabrúa and La Pedrera assemblages - the two sites that have yielded the greatest number of species- correspond to the Lower Cretaceous"Baissin type" (sensu Rasnitsyn et al., 1998), but including some Jurassic"survivors". La Pedrera assemblage fits equally well in the"angarosphecine subtype", while La Cabrúa roughly corresponds to the"proctotrupid" one, although shows a comparative ly high proportion of angarosphecins. This fact may suggest: a) possibly asynchrony between these two fossilsites, b) environmental differences not reflected in the lithological record, c) different taphonomic processes and/or, d) insufficient sample size - to reflect the reality of the source populations-. La Pedrera assemblage is very similar to those from Weald Clay (England), Bon Tsagan (Mongolia) and Santana (Brazil). La Cabrúa approaches to a some extent, though not quite agrees with the Purbeck (UK), Koonwarra (Australia), and most Lower Cretaceous Asian assemblages.

Availability of a soluble phosphorus source applied to soil samples with different acidicity levels

Considerations on the interactions of P in the soil-plant system have a long history, but are still topical and not yet satisfactorily understood. One concern is the effect of liming before or after application of soluble sources on the crop yield and efficiency of available P under these conditions. The aim of this study was to evaluate the effect of soil acidity on availability of P from a soluble source, based on plant growth and chemical extractants. Nine soil samples were incubated with a dose of 200 mg kg-1 P in soil with different levels of previously adjusted acidity (pH H2O 4.5; 5.0; 5.5; 6.0 and 6.5) and compared to soils without P application. After 40 days of soil incubation with a P source, each treatment was limed again so that all pH values were adjusted to 6.5 and then sorghum was planted. After the first and second liming the P levels were determined by the extractants Mehlich-1, Bray-1 and Resin, and the fractionated inorganic P forms. In general, the different acidity levels did not influence the P availability measured by plant growth and P uptake at the studied P dose. For some soils however these values increased or decreased according to the initial soil pH (from 4.5 to 6.5). Plant growth, P uptake and P extractable by Mehlich-1 and Bray-1 were significantly correlated, unlike resin-extractable P, at pH values raised to 6.5. These latter correlations were however significant before the second liming. The P contents extracted by Mehlich-1 and Bray-1 were significantly correlated with each other in the entire test range of soil acidity, even after adjusting pH to 6.5, besides depending on the soil buffering capacity for P. Resin was also sensitive to the properties that express the soil buffering capacity for P, but less clearly than Mehlich-1 and Bray-1. The application of triple superphosphate tended to increase the levels of P-Al, P-Fe and P-Ca and the highest P levels extracted by Bray-1 were due to a higher occurrence of P-Al and P-Fe in the soils.

Ammonium chloride as nitrogen source in sugarcane harvested without burning

The great difficulty of incorporation of N fertilizers into the "green sugarcane" system causes concern and since urea is the most commonly used source, there is the risk of loosing NH3 through volatilization. For this reason, a field experiment was undertaken (in a Hapludox Typic) with the objective of evaluating the agronomic efficiency of ammonium chloride on stubble of the second ratoon (SP89 1115), as well as its residual effect on the subsequent cycle (third ratoon). The experimental design was randomized blocks with four replications. Treatments consisted of three N rates (60, 120 and 180 kg ha-1 N) in the form of NH4Cl, in addition to a control treatment without the addition of N fertilizer. The ratoon cane of the second cutting was harvested in November 2006 and the treatments were applied in December 2006. The second ratoon was harvested mechanically in November 2007 and in December 2007, 450 kg ha-1 of the NPK mixture 20-05-19 was applied, providing 90, 22 and 86 kg ha-1 N, P2O5 and K2O, respectively, for the purpose of evaluating the effect of residual-N from the treatments implanted in December 2006. An increase in the rates of N-NH4Cl had a positive effect on the leaf concentrations of P, Mg and S. Stalk yield (MSS - Mg ha-1 of sugarcane stalks) and sugar (MSH - Mg ha-1 of sucrose) in the November 2006 harvest responded linearly to the increase of N doses in the form of NH4Cl. In relation to the effect of residual-N in the 2007/2008 harvest, it was observed, in general, that the concentrations of macronutrients in the sugarcane leaf +1 were within the range considered adequate in the state of São Paulo, Brazil. The residual-N of the NH4Cl doses resulted in a significant reduction in stalk (MSS) and sugar (MSH) production. It may be concluded that the NH4Cl source at a dose of 120 kg ha-1 N in ratoon fertilization of the second cutting was agronomically efficient, presenting, however, less efficiency of residual-N in the subsequent cycle.

Mobility of inorganic and organic phosphorus forms under different levels of phosphate and poultry litter fertilization in soils

The eutrophication of aquifers is strongly linked to the mobility of P in soils. Although P mobility was considered irrelevant in a more distant past, more recent studies have shown that P, both in organic (Po) and inorganic forms (Pi), can be lost by leaching and eluviation through the soil profile, particularly in less weathered and/or sandier soils with low P adsorption capacity. The purpose of this study was to determine losses of P forms by leaching and eluviation from soil columns. Each column consisted of five PVC rings (diameter 5 cm, height 10 cm), filled with two soil types: a clayey Red-Yellow Latosol and a sandy loam Red-Yellow Latosol, which were exposed to water percolation. The soils were previously treated with four P rates (as KH2PO4 ) to reach 0, 12.5, 25.0 and 50 % of the maximum P adsorption capacity (MPAC). The P source was homogenized with the whole soil volume and incubated for 60 days. After this period the soils were placed in the columns; the soil of the top ring was mixed with five poultry litter rates of 0, 20, 40, 80, and 160 t ha-1 (dry weight basis). Treatments consisted of a 4 x 5 x 2 factorial scheme corresponding to four MPAC levels, five poultry litter rates, two soils, with three replications, arranged in a completely randomized block design. Deionized water was percolated through the columns 10 times in 35 days to simulate about 1,200 mm rainfall. In the leachate of each column the inorganic P (reactive P, Pi) and organic P forms (unreactive P, Po) were determined. At the end of the experiment, the columns were disassembled and P was extracted with the extractants Mehlich-1 (HCl 0.05 mol L-1 and H2SO4 0.0125 mol L-1) and Olsen (NaHCO3 0.5 mol L-1; pH 8.5) from the soil of each ring. The Pi and Po fractions were measured by the Olsen extractant. It was found that under higher poultry litter rates the losses of unreactive P (Po) were 6.4 times higher than of reactive P (Pi). Both the previous P fertilization and increasing poultry litter rates caused a vertical movement of P down the soil columns, as verified by P concentrations extracted by Mehlich-1 and NaHCO3 (Olsen). The environmental critical level (ECL), i.e., the P soil concentration above which P leaching increases exponentially, was 100 and 150 mg dm-3 by Mehlich-1 and 40 and 60 mg dm-3 by Olsen, for the sandy loam and clay soils, respectively. In highly weathered soils, where residual P is accumulated by successive crops, P leaching through the profile can be significant, particularly when poultry litter is applied as fertilizer.

Water-dispersible clay in soils treated with sewage sludge

A by-product of Wastewater Treatment Stations is sewage sludge. By treatment and processing, the sludge is made suitable for rational and environmentally safe use in agriculture. The aim of this study was to assess the influence of different doses of limed sewage sludge (50 %) on clay dispersion in soil samples with different textures (clayey and medium). The study was conducted with soil samples collected from native forest, on a Red Latosol (Brazilian classification: Latossolo Vermelho distroférrico) loamy soil in Londrina (PR) and a Red-Yellow Latosol (BC: Latossolo Vermelho-Amarelo distrófico) medium texture soil in Jaguapitã (PR). Pots were filled with 3 kg of air-dried fine earth and kept in greenhouse. The experiment was arranged in a randomized block design with six treatments: T1 control, and treatments with limed sewage sludge (50 %) as follows: T2 (3 t ha-1), T3 (6 t ha-1), T4 (12 t ha-1), T5 (24 t ha-1) and T6 (48 t ha-1) and five replications. The incubation time was 180 days. At the end of this period, the pots were opened and two sub-samples per treatment collected to determine pH-H2O, pH KCl (1 mol L-1), organic matter content, water-dispersible clay, ΔpH (pH KCl - pH-H2O) and estimated PZC (point of zero charge): PZC = 2 pH KCl - pH-H2O, as well as the mineralogy of the clay fraction, determined by X ray diffraction. The results showed no significant difference in the average values for water-dispersible clay between the control and the other treatments for the two soil samples studied and ΔpH was the variable that correlated best with water-dispersible clay in both soils.

Evolution of source EEG synchronization in early Alzheimer's disease.

Alzheimer's disease (AD) disrupts functional connectivity in distributed cortical networks. We analyzed changes in the S-estimator, a measure of multivariate intraregional synchronization, in electroencephalogram (EEG) source space in 15 mild AD patients versus 15 age-matched controls to evaluate its potential as a marker of AD progression. All participants underwent 2 clinical evaluations and 2 EEG recording sessions on diagnosis and after a year. The main effect of AD was hyposynchronization in the medial temporal and frontal regions and relative hypersynchronization in posterior cingulate, precuneus, cuneus, and parietotemporal cortices. However, the S-estimator did not change over time in either group. This result motivated an analysis of rapidly progressing AD versus slow-progressing patients. Rapidly progressing AD patients showed a significant reduction in synchronization with time, manifest in left frontotemporal cortex. Thus, the evolution of source EEG synchronization over time is correlated with the rate of disease progression and should be considered as a cost-effective AD biomarker.

Chemical dispersants and pre-treatments to determine clay in soils with different mineralogy

Knowledge of the soil physical properties, including the clay content, is of utmost importance for agriculture. The behavior of apparently similar soils can differ in intrinsic characteristics determined by different formation processes and nature of the parent material. The purpose of this study was to assess the efficacy of separate or combined pre-treatments, dispersion methods and chemical dispersant agents to determine clay in some soil classes, selected according to their mineralogy. Two Brazilian Oxisols, two Alfisols and one Mollisol with contrasting mineralogy were selected. Different treatments were applied: chemical substances as dispersants (lithium hydroxide, sodium hydroxide, and hexametaphosphate); pre-treatment with dithionite, ammonium oxalate, and hydrogen peroxide to eliminate organic matter; and coarse sand as abrasive and ultrasound, to test their mechanical action. The conclusion was drawn that different treatments must be applied to determine clay, in view of the soil mineralogy. Lithium hydroxide was not efficient to disperse low-CEC electropositive soils and very efficient in dispersing high-CEC electronegative soils. The use of coarse sand as an abrasive increased the clay content of all soils and in all treatments in which dispersion occurred, with or without the use of chemical dispersants. The efficiency of coarse sand is not the same for all soil classes.

Generating vortex rings in Bose-Einstein condensates in the line-source approximation

We present a numerical method for generating vortex rings in Bose-Einstein condensates confined in axially symmetric traps. The vortex ring is generated using the line-source approximation for the vorticity, i.e., the curl of the superfluid velocity field is different from zero only on a circumference of a given radius located on a plane perpendicular to the symmetry axis and coaxial with it. The particle density is obtained by solving a modified Gross-Pitaevskii equation that incorporates the effect of the velocity field. We discuss the appearance of density profiles, the vortex core structure, and the vortex nucleation energy, i.e., the energy difference between vortical and ground-state configurations. This is used to present a qualitative description of the vortex dynamics.

Report on a special investigation of the Clay Central-Everly Community School District for the period July 1, 2005 through November 30, 2010

Report on a special investigation of the Clay Central-Everly Community School District for the period July 1, 2005 through November 30, 2010

Heat pulse line-source method to determine thermal conductivity of consolidated rocks

An instrument designed to measure thermal conductivity of consolidated rocks, dry or saturated, using a transient method is presented. The instrument measures relative values of the thermal conductivity, and it needs calibration to obtain absolute values. The device can be used as heat pulse line source and as continuous heat line source. Two parameters to determine thermal conductivity are proposed: TMAX, in heat pulse line source, and SLOPE, in continuous heat line source. Its performance is better, and the operation simpler, in heat pulse line-source mode with a measuring time of 170 s and a reproducibility better than 2.5%. The sample preparation is very simple on both modes. The performance has been tested with a set of ten rocks with thermal conductivity values between 1.4 and 5.2 W m¿1 K¿1 which covers the usual range for consolidated rocks.

Mineralogy of the clay fraction of Alfisols in two slope curvatures: III - spatial variability

A good knowledge of the spatial distribution of clay minerals in the landscape facilitates the understanding of the influence of relief on the content and crystallographic attributes of soil minerals such as goethite, hematite, kaolinite and gibbsite. This study aimed at describing the relationships between the mineral properties of the clay fraction and landscape shapes by determining the mineral properties of goethite, hematite, kaolinite and gibbsite, and assessing their dependence and spatial variability, in two slope curvatures. To this end, two 100 × 100 m grids were used to establish a total of 121 regularly spaced georeferenced sampling nodes 10 m apart. Samples were collected from the layer 0.0-0.2 m and analysed for iron oxides, and kaolinite and gibbsite in the clay fraction. Minerals in the clay fraction were characterized from their X-ray diffraction (XRD) patterns, which were interpreted and used to calculate the width at half height (WHH) and mean crystallite dimension (MCD) of iron oxides, kaolinite, and gibbsite, as well as aluminium substitution and specific surface area (SSA) in hematite and goethite. Additional calculations included the goethite and hematite contents, and the goethite/(goethite+hematite) [Gt/(Gt+Hm)] and kaolinite/(kaolinite+gibbsite) [Kt/(Kt+Gb)] ratios. Mineral properties were established by statistical analysis of the XRD data, and spatial dependence was assessed geostatistically. Mineralogical properties differed significantly between the convex area and concave area. The geostatistical analysis showed a greater number of mineralogical properties with spatial dependence and a higher range in the convex than in the concave area.

Mineralogy of the clay fraction of alfisols in two slope curvatures: IV - spatial correlation with physical properties

Although the influence of clay mineralogy on soil physical properties has been widely studied, spatial relationships between these features in Alfisols have rarely been examined. The purpose of this work was to relate the clay minerals and physical properties of an Alfisol of sandstone origin in two slope curvatures. The crystallographic properties such as mean crystallite size (MCS) and width at half height (WHH) of hematite, goethite, kaolinite and gibbsite; contents of hematite and goethite; aluminium substitution (AS) and specific surface area (SSA) of hematite and goethite; the goethite/(goethite+hematite) and kaolinite/(kaolinite+gibbsite) ratios; and the citrate/bicarbonate/dithionite extractable Fe (Fe d) were correlated with the soil physical properties through Pearson correlation coefficients and cross-semivariograms. The correlations found between aluminium substitution in goethite and the soil physical properties suggest that the degree of crystallinity of this mineral influences soil properties used as soil quality indicators. Thus, goethite with a high aluminium substitution resulted in large aggregate sizes and a high porosity, and also in a low bulk density and soil penetration resistance. The presence of highly crystalline gibbsite resulted in a high density and micropore content, as well as in smaller aggregates. Interpretation of the cross-semivariogram and classification of landscape compartments in terms of the spatial dependence pattern for the relief-dependent physical and mineralogical properties of the soil proved an effective supplementary method for assessing Pearson correlations between the soil physical and mineralogical properties.