Amostragem da emissão de material particulado em ambientes externos

The concern of the society with regard to the pollution if becomes each bigger and necessary time. This pollution generates damage for who is in contact, as much in economic terms how much in quality of life. The particulate matter is one of the main polluting the air, being the most harmful to human health, fine particles and ultra fine (below 2.5 μm in diameter). With this, this work had as objective to mensurar the pollution of air for material particulado through samplings in an urban center, in a siderurgical industry, a conventional coal bunker and a forest fire. The equipment used for the sampling of particles had been the DataRam4 (model DR 4000) and the Impactador de Andersen, both developed by company THERMO SCIENTIFIC. The first equipment uses a system of nefelometry and the second uses a gravimetrical system of sampling. During the carried through samplings, it can be observed in some cases the difficulty in the breath, badly be and low visibility that this type of pollutant can cause. In most cases the results were disturbing. In industry, conventional coal bunker and in the forest were measured values high concentration for particles smaller diameters. Peak concentrations issued were: 40,000 μg/m³, 182,000 μg/m³ and 400,000 μg/m³ for the industry, conventional coal bunker and forest, respectively. Already in the urban centre were satisfactory results, always staying within the limit allowed by the rules in force so far in the country

Efeito da amostragem de informação visual no comportamento locomotor adaptativo de pacientes com doença de Parkinson idiopática

Pouco se sabe a respeito da marcha de pacientes com doença de Parkinson (DP) em ambientes irregulares. Mais especificamente, não foram encontrados estudos que manipularam a informação visual na tarefa de ultrapassar obstáculo. Assim, o objetivo deste estudo foi analisar o papel da visão no comportamento locomotor durante a ultrapassagem de obstáculos de diferentes alturas em indivíduos com DP idiopática, manipulando experimentalmente a disponibilidade das informações visuais. Participaram 14 idosos com DP, classificados entre os estágios 1 e 2,5 da escala de Hoehn & Yahr. Os participantes foram convidados a percorrer andando uma passarela de 8 metros, em condições sem obstáculo (SO) e com obstáculo baixo (OB) ou alto (OA). As tentativas foram apresentadas combinando condições de obstáculo (SO, OB e OA) e de visão (IVD e IVE), em 3 tentativas por condição, totalizando 18 tentativas; realizadas em 2 blocos. A manipulação de informação visual foi realizada através do uso de óculos de lentes de cristal líquido e a análise cinemática foi realizada tridimensionalmente. As variáveis dependentes selecionadas incluíram os parâmetros espaciais e temporais das fases de aproximação e ultrapassagem do obstáculo. Para o tratamento dos dados, foram empregadas duas MANOVAs. Os resultados revelaram que tanto a manipulação visual como a manipulação do terreno influenciaram no comportamento locomotor dos pacientes. Na fase de aproximação, a presença do obstáculo provocou modificações nos parâmetros locomotores, refletindo em menores valores médios de comprimento e velocidade da passada nas condições OB e OA do que na condição SO. Em relação à informação visual nesta mesma fase, a anulação do fluxo óptico provocou diminuição do comprimento e da velocidade da passada, da cadência e da porcentagem da fase de suporte simples e aumento da duração... (Resumo completo, clicar acesso eletrônico abaixo)

Amostragem de poluentes gasosos e particulados emitidos pela queima de biomassa vegetal

The use of biomass as an energy source has been increasing in Brazil, with emphasis on the use of wood biomass, such as bark, wood chips and sawdust, that after receiving the appropriate treatment can be used in burners for power generation. However, from this burning are emitted fine particles known as particulate matter and a wide range of toxic organic and inorganic components in the form of gases that contribute greatly to air pollution and global warming, affecting human health, the environment and climate. The objective of this project was the quantification of gaseous and particulate, using and evaluating the equipment DR4000 ( Dataram 4 ) sampling of particulates smaller than 2.5μm and EUROTRON ( Ecoline 4000 ) when sampling gaseous pollutants, emitted from the burning of biomass in real time in the firing burner to a chimney attached biomass . We note that there are no specific rules that establish emission limits for particulate matter with diameter less than 2.5μm that are most harmful to human health and the highest concentrations reached about 800000μg/m3, for smaller diameters. It is noticeable the need for sampling of pollutants especially in industries that use biomass to fuel that could be implanted emission control equipment

Assembleias fitoplanctônicas no gradiente longitudinal barragem-jusante do reservatório de Itaipu, rio Paraná (Brasil/Paraguai)

The freshwater phytoplankton, responsible for a significant part of primary production in rivers and lakes, is of great importance for matter and energy available to other trophic levels of structuring aquatic food chains. In recent decades, the construction of dams, especially for the generation of electricity, produced changes not only in physical and chemical characteristics of rivers, but also in biocoenosis of these ecosystems. Thus, research is needed to expand the basic knowledge about these environments and subsidize actions appropriate conservation and management. Considering that lotic environments are relatively little studied, and the river-reservoir interaction, the work aims to analyze the limnological conditions and assemblies phytoplankton along the gradient established by the Itaipu reservoir and downstream stretch of the Paraná River. During two periods of the year, winter and summer, we analyzed nine sampling stations: one in lentic environment (the dam), six on the Parana River (each 5 km), at the mouth of a river Monday and another at the mouth of the Iguazu river. The phytoplankton community was composed of 315 taxa, with the class Bacillariophyceae most specious. At every point the richness was higher in summer and with a longitudinal trend in the increasing points after falling after the dam and the contribution of the tributaries. The number of taxa common to the three rivers was low in both study periods. The higher taxa can be explained by the variety of environments sampled, different residence times of water and nutrient concentrations, whereas the rivers Iguazu and Monday suffer high human influence. The greater abundance of organisms in the dam, in both periods, it should be the class Cryptophyceae contributing over 75% of total phytoplankton in point. In cluster analysis (composition and abundance)...(Complete abstract click electronic access below)

Amostragem de poluentes particulados emitidos pela queima de biomassa em correntes confinadas

It is clear today the ever-accelerating search for new fuels that will eventually replace those that will survive in our society, which are fossil fuels. For this reason, a fuel used since the dawn of humanity and much studied since then, considered the generator of clean, renewable energy, can earn more and more space in the power generation sector, which is biomass. We performed two experiments with two different types of biomass, one from the Amazon rainforest and other pine and eucalyptus as waste from the sawmill UNESP Itapeva. In the first experiment, conducted at the Laboratory of Combustion and Propulsion INPE Cachoeira Paulista were conducted three tests in a chimney with a fan creating forced ventilation, where the biomass was burned and deposited on a support beneath the hood. In the second experiment was conducted to analyze the emission of particulate matter using biomass (waste) from the sawmill on the campus of UNESP experimental Itapeva the burning of it in a burner for heating water for a wood oven. In these experiments we used a particle called DATARAM4 sampler that is capable of sampling both outdoors and inside of pipelines, which is the focus of this work. With this equipment it was possible to measure the concentration of particulate matter in all the firings as above, and compare them to levels acceptable in the current law, always trying to analyze the so-called fine particles, which are those with diameters less than 2.5 μm. Using data obtained from the equipment was also possible to evaluate the diametral distribution of particulate matter in question, and verify which phases of the flares in the concentration and the diameters of the particles are the most critical. In this work we concluded that in all firings conducted concentrations of particulate matter were higher than that allowed by the law, and the diameters were found that are more harmful to human health

Mapeamento geoestatístico da permeabilidade superficial no entorno do Ribeirão Claro: e simulação da possibilidade de sua contaminação

The evaluation of soil permeability throughout the weathering profile is one of the most important features to be considered in environmental studies. This study, developed from field testing and analysis of data obtained by geostatistical methods, aims at mapping the permeability around the Ribeirão Claro river. The intent is to simulate an accident with toxic liquids where soil permeability is of fundamental importance. Another purpose of the research was to determine the minimum time that, in the event of an accident, a possible contaminant to reach the water table level and be routed to the nearest drain, in this case, the Ribeirao V Claro river constitutes fundamental information. The studied area of approximately 4 km² is located within the UNESP-Rio Claro campus, consisting of colluvial soil from Fm. Rio Claro superimposed on residual soil of Fm. Corumbataí. The method used to determine the permeability is the concentric cylinders performed on a sampling grid with 64 points containing spacing of 5 meters EW and 10 meters NS. In the places of permeability tests were collected samples for laboratory determination of the percentage of fines. From particle size analysis was performed and analysis statistical and geostatistical on this data. The histogram was based on the statistical studies, and the semivariograms were based on geostatistical estimation methods. Based on the comparison between the maps and the data obtained, it was determined that the percentage of fines in colluvial surface soil has little influence on permeability, which the proximity to the Ribeirao Claro river, the eastern portion, a factor that influences the distribution of permeability values

Efeito do tratamento da superfície dental com os lasers Nd:YAG e Er: Yag na adesão da resina composta à dentina recém clareada

To evaluate the effect of surface treatment with Er:YAG and Nd:YAG laser on resin composite bond strength to recently bleached dentin. Material and Methods: In this study 120 bovine incisors were used and distributed into two groups: Group C: without bleaching treatment; Group B: with bleaching treatment (35% hydrogen peroxide). Each group was divided into three subgroups: Subgroup N: without laser treatment; Subgroup Nd: irradiation with Nd:YAG laser; Subgroup Er: irradiation with Er:YAG laser. Next, the adhesive system (Adper Single Bond 2) was applied and composite buildups were constructed with Z350 composite. The teeth were sectioned to obtain dentin-resin sticks (1x1mm) and analyzed by microtensile bond testing. The data were statistically analyzed by the ANOVA and Tukey tests. Results: The results showed that the bond strength values in the bleached control group (16.17 MPa) presented no significant difference in comparison with the group bleached and irradiated with Er:YAG laser (14.69 MPa). The non bleached control group (26.79 MPa) presented significant difference in bond strength when compared with the non bleached group irradiated with Er:YAG laser (22.82 MPa) and with the group treated by bleaching and irradiation with Nd:YAG laser (28,792 MPa). The group without bleaching treatment and irradiated with Nd:YAG (36.1 MPa) presented a significant increase in bond strength in comparison with the other groups. Conclusion: The use of Nd:YAG laser on bleached specimens was able of completely reversing the immediate effects of bleaching, obtaining bond strength values similar to those of the control group

Amostragem diurna versus noturna de ácaros (Arachnida: Acari) associados a Genipa americana L. (Rubiaceae)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito do tipo de adesivo e do seu mecanismo de ativação, assim como da viscosidade da resina composta, na resistência de união à dentina antes e após envelhecimento artificial

Pós-graduação em Odontologia Restauradora - ICT

Protese total fixa em função imediata confeccionada em resina composta indireta

Immediate functioning of osseointegrated implants has been widely employed in edentulous patients due to its safety and high predictability. However, viability and success of immediate-loaded implants is defined by factors such as number of implants, distribution and splinting, as well as reduction of oblique loads and excessive occlusal contacts. The indirect composite resin-modified glass enable building of a highly aesthetic prosthesis, combining satisfactory resistance and better force dissipation on occlusal loading. This article describes a resin composite, mandibular fixed prosthesis on osseointegrated implants in immediate function.

Efeitos de diferentes sistemas de clareamento dental sobre a rugosidade e morfologia superficial do esmalte e de uma resina composta restauradora

The aim of this study was to evaluate and compare the roughness and superficial morphology of enamel and a composite restorative resin after different bleaching techniques application. Material and Methods: Bovine incisors were selected and standardized cavities were prepared on the buccal surface, which were restored with composite resin. The teeth were distributed according to the following treatments: G1- bleaching with 10% carbamide peroxide (CP); G2 - bleaching with 38% hydrogen peroxide (HP); and G3 - bleaching with 38% of HP associated to light irradiation. For G1, the bleaching gel was applied for 8 hours daily during 21 days. For G2 and G3, 3 sessions were performed, consisting of 3 applications of 15 minutes each, with 7 days of intervals between the sessions. For G3, the LED (470nm) light was used to activate the bleaching agent for 6 minutes. The surface of enamel and composite resin were evaluated before and after the bleaching procedures using a roughness tester and an atomic force microscope. Results: The results showed significant differences in surface roughness of enamel after bleaching only for G1 (Wilcoxon, p<0.05). For composite resin, neither group showed a statistical difference compared to control (Mann-Whitney, p>0.05). Conclusion: It was concluded that the increase in the roughness of enamel occurred only after bleaching therapy using a gel with 10% of CP. The bleaching procedures evaluated in this investigation did not increase the roughness or cause changes in the superficial morphology of the composite resin.

Resina composta indireta como alternativa funcional e estética em reabilitações protéticas

Due to mechanical and aesthetic improvement properties, continuous fiber-reinforced composites have been developed to replace the metal framework in fixed partial dentures becoming an interesting alternative to conventional treatments. A male patient, 57 years old, attended at Fixed Partial Denture Clinic of Araraquara Dental School - UNESP, complaining about upper right first molar absence. After clinical examination, it was observed: upper right second molar with amalgam restoration and periodontal bone reduction and upper right second premolar unsatisfactory treated. Following the clinical conditions and the patient expectations, it was decided to use a fiber-reinforced composite resin to make a three-element fixed bridge. The patient showed full satisfaction with the aesthetic and functional results. The case has been followed up for 60 months.

Matriz oclusal para restauração com resina composta de baixa contração: simplificação eficiência

The composite resin is the material of election for direct restorations in posterior teeth currently. The restorative dentistry aims to improve each day the material and facilitate the restorative technique. This paper describes the technique of occlusal matrix made to speed up and preservation the occlusal surface of a first molar tooth affected by caries lesion. A new resin-based composite was used called Silorane, which may be placed in larger increments due the material has low shrinkage and polymerization stress. The use of occlusal matrix associated with a low shrinkage resin composite can simplify the clinical work, and result in a restoration with excellent reproduction of anatomical.

Reparo de uma restauração classe IV com o uso de resina composta nanoparticulada: quatro anos de acompanhamento

O aprimoramento da odontologia estética restauradora está ligado ao desenvolvimento de materiais e técnicas inovadoras, os quais podem oferecer diversos benefícios, incluindo a integração cromática, policromatismo, forma anatômica, função, adequado contato proximal e aumento da integridade marginal. Em função desses aspectos, as restaurações de resina composta, aplicadas de forma direta, tendem a ganhar maior longevidade. Assim, o objetivo do presente relato de caso é fornecer ao leitor a visão dos desafios restauradores envolvidos no reparo de uma fratura classe IV de um dente incisivo superior, utilizando-se um novo sistema de resina composta híbrida nanoparticulada (FiltekTM Supreme - 3M ESPE). Resultados: com base no referido material e técnica, otimizamos a obtenção de resultados satisfatórios alcançados por meio da utilização adequada do sistema adesivo e resina composta, mantidos com sucesso após o acompanhamento de 4 anos. Conclusão: pode-se concluir que, interagindo técnica adequada de aplicação, princípios adesivos básicos e materiais de qualidade, o clínico pode garantir o sucesso na restauração da forma, função e estética de dentes anteriores.