A técnica de dispersão de taylor para estudos de difusão em líquidos e suas aplicações

This paper describes the theoretical basis and the experimental requirements for the application of the Taylor dispersion technique for measurements of diffusion coefficients in liquids, emphasizing its simplicity and accuracy in comparison to other usual techniques. Some examples are discussed describing the use of this methodology on studies of solute-solvent interactions, solute aggregation, solute partitioning into macromolecular systems and on the assessment of nanoparticles sizes.

Model-based objects recognition in man-made environments

We describe a model-based objects recognition system which is part of an image interpretation system intended to assist autonomous vehicles navigation. The system is intended to operate in man-made environments. Behavior-based navigation of autonomous vehicles involves the recognition of navigable areas and the potential obstacles. The recognition system integrates color, shape and texture information together with the location of the vanishing point. The recognition process starts from some prior scene knowledge, that is, a generic model of the expected scene and the potential objects. The recognition system constitutes an approach where different low-level vision techniques extract a multitude of image descriptors which are then analyzed using a rule-based reasoning system to interpret the image content. This system has been implemented using CEES, the C++ embedded expert system shell developed in the Systems Engineering and Automatic Control Laboratory (University of Girona) as a specific rule-based problem solving tool. It has been especially conceived for supporting cooperative expert systems, and uses the object oriented programming paradigm

Uma interface lab-made para aquisição de sinais analógicos instrumentais via porta paralela do microcomputador

A lab-made interface for acquisition of instrumental analog signals between 0 and 5 V at a frequency up to 670 kHz at the parallel port of a microcomputer is described. Since it uses few and small components, it was built into the connector of a printer parallel cable. Its performance was evaluated by monitoring the signals of four different instruments and similar analytical curves were obtained with the interface and from readings from the instrument' displays. Because the components are cheap (~U$35,00) and easy to get, the proposed interface is a simple and economical alternative for data acquisition in small laboratories for routine work, research and teaching.

On the development of object functions and restrictions for shapes made with a turret punch press

This study presents the information required to describe the machine and device resources in the turret punch press environment which are needed for the development of the analysing method for automated production. The description of product and device resources and their interconnectedness is the starting point for method comparison the development of expenses, production planning and the performance of optimisation. The manufacturing method cannot be optimized unless the variables and their interdependence are known. Sheet metal parts in particular may then become remarkably complex, and their automatic manufacture may be difficult or, with some automatic equipment, even impossible if not know manufacturing properties. This thesis consists of three main elements, which constitute the triangulation. In the first phase of triangulation, the manufacture occuring on a turret punch press is examined in order to find the factors that affect the efficiency of production. In the second phase of triangulation, the manufacturability of products on turret punch presses is examined through a set of laboratory tests. The third phase oftriangulation involves an examination of five industry parts. The main key findings of this study are: all possible efficiency in high automation level machining cannot be achieved unless the raw materials used in production and the dependencies of the machine and tools are well known. Machine-specific manufacturability factors for turret punch presses were not taken into account in the industrial case samples. On the grounds of the performed tests and industrial case samples, the designer of a sheet metal product can directly influence the machining time, material loss, energy consumption and the number of tools required on a turret punch press by making decisions in the way presented in the hypothesis of thisstudy. The sheet metal parts to be produced can be optimised to bemanufactured on a turret punch press when the material to be used and the kinds of machine and tool options available are known. This provides in-depth knowledge of the machine and tool properties machine and tool-specifically. None of the optimisation starting points described here is a separate entity; instead, they are all connected to each other.

The figure of the earth, determined from observations made by order of the French King, at the polar circle: by Messrs de Maupertuis, Camus, Clairaut, Le Monnier, members of the Royal Academy of Sciences, the abbé Outhier, correspondent of the Academy, and Mr. Celsius, professor of astronomy at Upsal : translated from the French of M. de Maupertuis.

Digital reproduction, The National Library of Finland, Centre for Preservation and Digitisation, Mikkeli

Enhancing performance of paper coatings by tailor-made plastic pigments

The paper industry is constantly looking for new ideas for improving paper products while competition and raw material prices are increasing. Many paper products are pigment coated. Coating layer is the top layer of paper, thus by modifying coating pigment also the paper itself can be altered and value added to the final product. In this thesis, synthesis of new plastic and hybrid pigments and their performance in paper and paperboard coating is reported. Two types of plastic pigments were studied: core-shell latexes and solid beads of maleimide copolymers. Core-shell latexes with partially crosslinked hydrophilic polymer core of poly(n-butyl acrylate-co-methacrylic acid) and a hard hydrophobic polystyrene shell were prepared to improve the optical properties of coated paper. In addition, the effect of different crosslinkers was analyzed and the best overall performance was achieved by the use of ethylene glycol dimethacrylate (EGDMA). Furthermore, the possibility to modify core-shell latex was investigated by introducing a new polymerizable optical brightening agent, 1-[(4-vinylphenoxy)methyl]-4-(2-henylethylenyl)benzene which gave promising results. The prepared core-shell latex pigments performed smoothly also in pilot coating and printing trials. The results demonstrated that by optimizing polymer composition, the optical and surface properties of coated paper can be significantly enhanced. The optimal reaction conditions were established for thermal imidization of poly(styrene-co-maleimide) (SMI) and poly(octadecene-co-maleimide) (OMI) from respective maleic anhydride copolymer precursors and ammonia in a solvent free process. The obtained aqueous dispersions of nanoparticle copolymers exhibited glass transition temperatures (Tg) between 140-170ºC and particle sizes from 50-230 nm. Furthermore, the maleimide copolymers were evaluated in paperboard coating as additional pigments. The maleimide copolymer nanoparticles were partly imbedded into the porous coating structure and therefore the full potential of optical property enhancement for paperboard was not achieved by this method. The possibility to modify maleimide copolymers was also studied. Modifications were carried out via N-substitution by replacing part of the ammonia in the imidization reaction with amines, such as triacetonediamine (TAD), aspartic acid (ASP) and fluorinated amines (2,2,2- trifluoroethylamine, TFEA and 2,2,3,3,4,4,4-heptafluorobuthylamine, HFBA). The obtained functional nanoparticles varied in size between 50-217 nm and their Tg from 150-180ºC. During the coating process the produced plastic pigments exhibited good runnability. No significant improvements were achieved in light stability with TAD modified copolymers whereas nanoparticles modified with aspartic acid and those containing fluorinated groups showed the desired changes in surface properties of the coated paperboard. Finally, reports on preliminary studies with organic-inorganic hybrids are presented. The hybrids prepared by an in situ polymerization reaction consisted of 30 wt% poly(styrene- co-maleimide) (SMI) and high levels of 70 wt% inorganic components of kaolin and/or alumina trihydrate. Scanning Electron Microscopy (SEM) images and characterization by Fourier Transform Infrared Spcetroscopy (FTIR) and X-Ray Diffraction (XRD) revealed that the hybrids had conventional composite structure and inorganic components were covered with precipitated SMI nanoparticles attached to the surface via hydrogen bonding. In paper coating, the hybrids had a beneficial effect on increasing gloss levels.

Aplicação do diagrama de Taylor para avaliação de interpoladores espaciais em atributos de solo em cultivo com eucalipto

As diversas técnicas de interpolação espacial adotadas oferecem desempenhos diferentes, de acordo com as características dos dados iniciais, e é muito comum encontrar avaliadores contando somente com R² (coeficiente de determinação múltiplo) e erro residual. Neste trabalho, objetivou-se aplicar o Diagrama de Taylor para analisar 15 métodos diferentes de interpolação espacial, em área com cultivo comercial de eucalipto, para comparação e escolha do melhor método de interpolação de um conjunto de valores da fração granulométrica do solo (argila), na profundidade de 0-0,20 m do solo. De acordo com os resultados, considera-se muito satisfatória a ferramenta do Diagrama de Taylor, pois, além de definir graficamente os melhores métodos de interpolação, essa ferramenta permite fazer escolhas entre eles, dentro de um conjunto menor e mais definido de informações; logo, optou-se pelo método Splines em detrimento da krigagem modelo linear. As estatísticas desses dois métodos estão muito próximas, com pequenas variações, estando o desvio-padrão do Splines mais próximo dos dados observados; logo, é o melhor método de interpolação para argila, na profundidade de 0-0,20 m do solo.

Ajuste do método de Priestley-Taylor às condições climáticas locais

A sustentabilidade da agricultura irrigada depende primariamente do manejo eficiente da irrigação, de modo a aumentar a produtividade primária de uma cultura em determinada localidade. A eficiência no uso de água pode ser melhorada pelo próprio esquema de irrigação adotado, sendo essencialmente governado pelas condições climáticas. O planejamento da irrigação e a tomada de decisão são funções do conhecimento da demanda evaporativa da atmosfera, sendo expressa pela demanda potencial (ETo). Em geral, quase todos os métodos de estimativa de ETo reportados na literatura referem-se a valores diários, incluindo-se nessa situação as perdas noturnas de evaporação, as quais serão expressivas apenas em alguns dias após a chuva ou irrigação. Desenvolveu-se, no presente estudo, método corrigido para estimar ETo, baseado no balanço de energia local, a partir de dados meteorológicos monitorados em postos de observação de superfície durante o período de luz. Para validação do método de Priestley-Taylor ajustado às condições locais, foram utilizados dados observados em estação meteorológica automática instalada em Piracicaba - SP, bem como medidas lisimétricas coletadas na Fazenda Areião da área experimental da ESALQ/USP. Estudos de regressão revelaram que o método proposto apresentou excelentes resultados quando comparado com o método de Penman-Monteith e com medidas realizadas em lisímetros de pesagem com célula de carga, dados os elevados valores de coeficiente de determinação obtidos, podendo ser recomendado, portanto, em estudos de avaliação de consumo de água das culturas em diversas localidades.

Locally made equipment

kuv., 22 x 29 cm

Capacity of an I-beam made of S960 QC based on Eurocode 3

The capacity of beams is a very important factor in the study of durability of structures and structural members. The capacity of a high-strength steel I-beam made of S960 QC was investigated in this study. The investigation included assessment of the service limits and ultimate limits of the steel beam. The thesis was done according to European standards for steel structures, Eurocode 3. An analytical method was used to determine the throat thickness, deformation, elastic and plastic moment capacities as well as the fatigue life of the beam. The results of the analytical method were compared with those obtained by Finite Element Analysis (FEA). Elastic moment capacity obtained by the analytical method was 172 kNm. FEA and the analytical method predicted the maximum lateral-torsional buckling (LTB) capacity in the range of 90-93 kNm and the probability of failure as a result of LTB is estimated to be 50%. The lateral buckling capacity meant that the I-beam can carry a safe load of 300 kN instead of the initial load of 600 kN. The beam is liable to fail shortly after exceeding the elastic moment capacity. Based on results in of the different approaches, it was noted that FEA predicted higher deformation values on the load-deformation curve than the analytical results. However, both FEA and the analytical methods predicted identical results for nominal stress range and moment capacities. Fatigue life was estimated to be in the range of 53000-64000 cycles for bending stress range using crack propagation equation and strength-life approach. As Eurocode 3 is limited to steel grades up to S690, results for S960 must be verified with experimental data and appropriate design rules.

A New Model to Determine the Dispersion of Fatigue Damage Evaluations

Reliable predictions of remaining lives of civil or mechanical structures subjected to fatigue damage are very difficult to be made. In general, fatigue damage is extremely sensitive to the random variations of material mechanical properties, environment and loading. These variations may induce large dispersions when the structural fatigue life has to be predicted. Wirsching (1970) mentions dispersions of the order of 30 to 70 % of the mean calculated life. The presented paper introduces a model to estimate the fatigue damage dispersion based on known statistical distributions of the fatigue parameters (material properties and loading). The model is developed by expanding into Taylor series the set of equations that describe fatigue damage for crack initiation.

European luxury brands made in China: the effect of low-cost country manufacturing on brand image and purchase decisions

European luxury brands have an image of manufacturing their products in the same country where the brands originate. However, in the past years many luxury brands have shifted their manufacturing to countries outside Europe. China is now a common manufacturing country for European luxury brands despite the country’s poor image as a manufacturer. Chinese manufacturing is often associated with bad quality, bad labour conditions, mass production, and counterfeits. The image of China does not quite match the image luxury brands enjoy including characteristics such as high end quality, craftsmanship, details, design, or premium price. A negatively perceived country-of-manufacture may have an effect on a brand’s image and consumers’ purchase decisions. This thesis is focused on European luxury brands manufacturing in China, and how this effects the brand image and purchase decisions among luxury consumers. The empirical part of this thesis is based on focus group research, which is a popular method in the field of qualitative research. The main focus group is female luxury consumers in Finland. This main group has been divided into three categories: 1) the university students, 2) the young career women, 3) the experienced luxury consumers. This categorization has been done based on their different stages in luxury consumption. All in all, the empirical research consisted of 11 interviews and 29 participants. The main contribution of this thesis was that there is a difference between the opinions of the younger groups (university students and young career women) and the experienced luxury consumers when discussing the effect of country-of-manufacture on brand image and purchase decisions of luxury brands. The younger participants thought that manufacturing luxury products in China might affect the brand image, but their purchase decisions would not be that much affected by the country-of-origin. The experienced luxury consumers had quite a different view on the country-of-origin of luxury brands – they found it an important decisive factor prior making purchases. The majority of experienced luxury consumers would not buy luxury products made in China, and they would always check where these products are made in.

Morphology and reproduction of Mesophyllum erubescens (Foslie) Me. Lemoine (Corallinales, Rhodophyta) from Southern Brazil

The genus Mesophyllum Me. Lemoine includes around 147 species, of which only three have been referred to the Brazilian coast. Mesophyllum erubescens was originally described from Fernando de Noronha Archipelago, Brazil (type locality). Here we present the first detailed description of M. erubescens based on Brazilian material. Samplings were made through scuba diving at the Biological Marine Reserve of Arvoredo Island, Santa Catarina. The relations of M. erubescens with other similar species, especially from the American Atlantic studied by W.R. Taylor are discussed.