Controle de velocidade e tração de rodas independentes para veículos elétricos

This work presents a proposal to replace thetraditional system of traction electric car that usesone electric motor and a mechanical differential, by two electric motors of lower power, controlled byelectronic control low cost. The proposed control isopen loop and uses the technique of Pulse WidthModulation (PWM), discrete and synchronizedaiming to reduce the generation of harmonics. The implementation of two smaller motor one on each wheel-drive distributes the weight of the vehicle, improving the heat exchange of the windings,beyond enable the power components supporting a current of 50% predicted for only one motor . The solution adopted for being open-loop, has a similar behavior to the mechanical differential, where theeffort imposed by the trajectory makes the velocity distribution between the wheels be appropriate tovehicle trajectory

Controlador PID utilizando microcontrolador PIC

This monograph proposes the implementation of a low cost PID controller utilizing a PIC microcontroller, and its application in a positioning system previously controlled by a dedicated integrated circuit for a positioning system. Applying the closed-loop PID control, the system instability was reduced, and its response was smoother, eliminating vibrations and mechanical wear compared to its response with the dedicated integrated circuit, which has a very limited control action. The actuator of the system is a DC motor, whose speed is controlled by the Pulse Width Modulation (PWM) technique, using a Full-Bridge circuit, allowing the shift of direction of rotation. The utilized microcontroller was the PIC16F684, which has an enhanced PWM module, with its analog converters used as reference and position feedback. The positioning sensor is a multiturn potentiometer coupled to the motor axis by gears. The possibility of programming the PID coefficients in the microcontroller, as well as the adjustment of the sampling rate, allows the implemented system achieving high level of versatility

Improvement to the physical quality and imbibition pattern in seeds of candeia (Eremanthus incanus (Less.) Less.)

The objective of this work was to develop a methodology for seed processing and X-ray analysis and to study imbibition pattern in seeds of candeia (Eremanthus incanus). Seeds were gathered in 2001 and 2002 in Morro do Pilar and Lavras respectively, processed and stored in a cold chamber (5ºC/60%RH) until the start of experiments. In order to identify unfilled seeds, a protocol was developed for X-ray use combining radiation energy (Kv) and exposure time (seconds). For elimination of unfilled seeds, an experiment was conducted using a South Dakota seed blower whereby different opening settings and ventilation times were combined. Original seed lots and categorized lots following radiograph viewing were tested by germination tests, with seeds being cleansed in sodium hypochlorite and scattered over blotting paper in 'gerboxes' and then taken to germinators with alternating temperatures of 20º-30ºC and 10 hours of light, for up to 15 days. Imbibition curves were determined under the conditions 30ºC, 20º-30ºC/10 hours of light and 30º-20ºC/10 hours of light. The X-ray protocol that best allowed viewing of internal seed structures was 30Kv for 45 seconds. Seed separation using the blower setting at a 3.0 opening for 30 seconds raised the number of embryonic seeds to values exceeding 99%, also raising the germination rates as a consequence. The imbibition pattern is three-phased and the germination process is completed in 72 hours. Under alternate temperatures, primary root growth is favored.

Sistema de geração e armazenamento de energia elétrica utilizando transdutor piezelétrico na forma pulsada

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Compensação ativa paralela baseada na teoria de potência conservativa

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise dos ciclos operacionais para especificação de motores de indução trifásicos

This paper addresses the three-phase induction motor by a thermal analysis of its operation, under the gaze of the standards of the Brazilian Association of Technical Standards that deal with working arrangements (operating cycles) defined by appropriate tests and for each use of the motor basis of this study, emphasizing especially the fact of the first three cycles are the cycles with greater possibilities of use for scaling a three-phase induction motor for the main industrial processes, will also be made an analysis of the reasons why the three-phase induction motors have a loss of power at altitudes above 1000 m above sea level and some methods of how to define how a three phase induction motor can be used in one of the first three working arrangements

Evaluation of an In Vitro Blood-Based Assay to Detect Production of Interferon-γ By Mycobacterium Bovis–Infected White-Tailed Deer (Odocoileus Virginianus)

Tuberculosis due to Mycobacterium bovis in captive Cervidae was identified as an important disease in the United States in 1990 and prompted the addition of captive Cervidae to the USDA Uniform Methods and Rules for eradication of bovine tuberculosis. As well, M. bovis infection was identified in free-ranging white-tailed deer in northeast Michigan in 1995. Tuberculosis in both captive and free-ranging Cervidae represents a serious challenge to the eradication of M. bovis infection from the United States. Currently, the only approved antemortem tests for tuberculosis in Cervidae are the intradermal tuberculin skin test and the blood tuberculosis test (BTB). At present, the BTB is not available in North America. Tuberculin skin testing of Cervidae is time-consuming and involves repeated animal handling and risk of injury to animals and humans. This study evaluated the potential of a new blood-based assay for tuberculosis in Cervidae that would decrease animal handling, stress, and losses due to injury. In addition, a blood-based assay could provide a more rapid diagnosis. Twenty 6–9-month-old white-tailed deer, male and female, were experimentally inoculated by instillation of 300 colony-forming units of M. bovis in the tonsillar crypts. Seven, age-matched uninfected deer served as controls. Blood was collected on days 90, 126, 158, 180, 210, 238, 263, and 307 after inoculation and was analyzed for the production of interferon-γ (IFN-γ) in response to incubation with M. bovis purified protein derivative (PPDb), M. avium PPDa, pokeweed mitogen (PWM), or media alone. Production of IFN-g in response to PPDb was significantly greater (P < 0.05) at all time points in samples from M. bovis–infected deer as compared with uninfected control deer, whereas IFN-γ production to PWM did not differ significantly between infected and control deer. Measurement of IFN-γ production to PPDb may serve as a useful assay for the antemortem diagnosis of tuberculosis in Cervidae.

Análise dos ciclos operacionais para especificação de motores de indução trifásicos

This paper addresses the three-phase induction motor by a thermal analysis of its operation, under the gaze of the standards of the Brazilian Association of Technical Standards that deal with working arrangements (operating cycles) defined by appropriate tests and for each use of the motor basis of this study, emphasizing especially the fact of the first three cycles are the cycles with greater possibilities of use for scaling a three-phase induction motor for the main industrial processes, will also be made an analysis of the reasons why the three-phase induction motors have a loss of power at altitudes above 1000 m above sea level and some methods of how to define how a three phase induction motor can be used in one of the first three working arrangements

Diseño, implementación y verificación de un controlador para robots educativos

[EN] This project briefly analyzes the scope and applications of Industrial Robotics, as well as the importance that this technical discipline has gained in the past decades. In addition, it proposes a modern platform to assist in teaching this discipline in colleges and universities. This new educational platform for the teaching of Industrial Robotics is based on the robotic systems from Rhino Robotics Ltd., using the existing robotic arms and replacing the control electronics by a newer, modern and yet backwards-compatible controller. In addition to the controller, this platform also provides new, up-to-date software utilities that are more intuitive than those provided with the old system. The work to be done consists essentially in receiving commands from a personal computer which the controller must interpret in order to control the motors of the robotic arm. The controller itself will be implemented as an embedded system based on microcontrollers. This requires the implementation of a communication protocol between the personal computer and the microcontroller, the design of a command interpreter, the design of the electronics for motor control using PWM and H-bridges, and the implementation of control techniques (more precisely, PID control). Hence, this project combines software and hardware design and integration techniques with motor control techniques and feedback control methods from Control Engineering, along with the kinematic analysis of the Rhino XR-4 robotic arm. 

Realizzazione e collaudo di un inverter di media tensione per prove su formette

L’introduzione massiccia dell’elettronica di potenza nel campo degli azionamenti elettrici negli ultimi decenni ha sostanzialmente rivoluzionato la tipologia di alimentazione dei motori elettrici. Da un lato ciò ha migliorato la qualità del controllo della velocità, ma dall’altro ha aggravato le sollecitazioni che gli isolanti delle macchine devono sopportare. Si è infatti passati da tecniche di controllo tradizionali, che consistevano nell’alimentare i motori in alternata direttamente con la rete sinusoidale a 50 Hz (o a 60 Hz), ad alimentazioni indirette, cioè realizzate interponendo tra la rete e la macchina un convertitore elettronico (inverter). Tali dispositivi operano una conversione di tipo ac/dc e dc/ac che permette, come nella modulazione Pulse Width Modulation (PWM), di poter variare la frequenza di alimentazione della macchina, generando una sequenza di impulsi di larghezza variabile. Si è quindi passati dalle tradizionali alimentazioni con forme d’onda alternate sinusoidali a forme di tensione impulsive e ad elevata frequenza, cioè caratterizzate da rapidi fronti di salita e di discesa (dell’ordine di qualche kV/µs). La natura impulsiva di queste forme d’onda ha aggravato la sollecitazione elettrica a cui sono sottoposti i materiali impiegati per l’isolamento dei conduttori degli avvolgimenti delle macchine. E’ importante notare che l’utilizzo dei dispositivi elettronici, che ormai si trovano sparsi nelle reti di bassa tensione, assorbono correnti ad elevato contenuto armonico sul lato di prelievo, hanno quindi un effetto distorcente che altera l’andamento sinusoidale della rete stessa. Quindi, senza opportuni filtri, anche tutte le altre utenze connesse nelle vicinanze, dimensionate per alimentazioni sinusoidali di tipo tradizionale, possono risentire di queste distorsioni armoniche. Per tutti questi motivi è sorta la necessità di verificare l’adeguatezza dei tradizionali isolamenti ad essere in grado di sopportare le sollecitazioni che derivano dall’utilizzo di convertitori elettronici. In particolare, per i motori elettrici tale interrogativo è stato posto in seguito al verificarsi di un elevato numero di guasti inaspettati (precoci), probabilmente imputabile alla diversa sollecitazione elettrica applicata ai materiali. In questa tesi ci si è occupati della progettazione di un inverter di media tensione, che verrà impiegato per eseguire prove sugli avvolgimenti di statore di motori (formette), al fine di condurre successivamente uno studio sull’invecchiamento dei materiali che compongono gli isolamenti. Tale inverter è in grado di generare sequenze di impulsi con modulazione PWM. I parametri caratteristici delle sequenze possono essere modificati in modo da studiare i meccanismi di degradazione in funzione della tipologia delle sollecitazioni applicate. Avendo a che fare con provini di natura capacitiva, il cui isolamento può cedere durante la prova, il sistema deve essere intrinsecamente protetto nei confronti di tutte le condizioni anomale e di pericolo. In particolare deve essere in grado di offrire rapide ed efficaci protezioni per proteggere l’impianto stesso e per salvaguardare la sicurezza degli operatori, dato l’elevato livello delle tensioni in gioco. Per questo motivo è stata pensata un’architettura di sistema ad hoc, in grado di fronteggiare le situazioni anomale in modo ridondante. E’ infatti stato previsto l’inserimento di un sistema di controllo basato sul CompactRIO, sul quale è stato implementato un software in grado di monitorare le grandezze caratteristiche del sistema e le protezioni che affiancheranno quelle hardware, realizzate con dispositivi elettronici. I dispositivi elettronici di protezione e di interfacciamento sono stati studiati, implementati e simulati con PSpice, per poi essere successivamente dimensionati e realizzati su schede elettroniche, avvalendosi del software OrCAD. La tesi è strutturata come segue: - Il primo capitolo tratta, in maniera generale, i motori asincroni trifase, gli inverter e l’invecchiamento dei sistemi isolanti, con particolare interesse alle sollecitazioni meccaniche, termiche ed elettriche nel caso di sollecitazioni impulsive; - Il secondo capitolo riguarda il sistema realizzato nel suo complesso. Inizialmente verrà descritto lo schema elettrico generale, per poi analizzare più nello specifico le varie parti di cui il sistema è composto, come l’inverter di media tensione, il generatore di media tensione, la scheda di disaccoppiamento ottico, la scheda di controllo del generatore di media tensione, la scheda OCP; - Il terzo capitolo descrive le lavorazioni meccaniche eseguite sulle scatole contenti i rami di inverter, la realizzazione delle fibre ottiche e riporta le fasi di collaudo dell’intero sistema. Infine, verranno tratte le conclusioni.

A multilevel converter structure for grid-connected PV plants

A new conversion structure for three-phase grid-connected photovoltaic (PV) generation plants is presented and discussed in this Thesis. The conversion scheme is based on two insulated PV arrays, each one feeding the dc bus of a standard 2-level three-phase voltage source inverter (VSI). Inverters are connected to the grid by a traditional three-phase transformer having open-end windings at inverters side and either star or delta connection at the grid side. The resulting conversion structure is able to perform as a multilevel VSI, equivalent to a 3-level inverter, doubling the power capability of a single VSI with given voltage and current ratings. Different modulation schemes able to generate proper multilevel voltage waveforms have been discussed and compared. They include known algorithms, some their developments, and new original approaches. The goal was to share the grid power with a given ratio between the two VSI within each cycle period of the PWM, being the PWM pattern suitable for the implementation in industrial DSPs. It has been shown that an extension of the modulation methods for standard two-level inverter can provide a elegant solution for dual two-level inverter. An original control method has been introduced to regulate the dc-link voltages of each VSI, according to the voltage reference given by a single MPPT controller. A particular MPPT algorithm has been successfully tested, based on the comparison of the operating points of the two PV arrays. The small deliberately introduced difference between two operating dc voltages leads towards the MPP in a fast and accurate manner. Either simulation or experimental tests, or even both, always accompanied theoretical developments. For the simulation, the Simulink tool of Matlab has been adopted, whereas the experiments have been carried out by a full-scale low-voltage prototype of the whole PV generation system. All the research work was done at the Lab of the Department of Electrical Engineering, University of Bologna.

Analysis and Implementation of Multiphase-Multilevel Inverter for Open-Winding Loads

Research work carried out in focusing a novel multiphase-multilevel ac motor drive system much suitable for low-voltage high-current power applications. In specific, six-phase asymmetrical induction motor with open-end stator winding configuration, fed from four standard two-level three-phase voltage source inverters (VSIs). Proposed synchronous reference frame control algorithm shares the total dc source power among the 4 VSIs in each switching cycle with three degree of freedom. Precisely, first degree of freedom concerns with the current sharing between two three-phase stator windings. Based on modified multilevel space vector pulse width modulation shares the voltage between each single VSIs of two three-phase stator windings with second and third degree of freedom, having proper multilevel output waveforms. Complete model of whole ac motor drive based on three-phase space vector decomposition approach was developed in PLECS - numerical simulation software working in MATLAB environment. Proposed synchronous reference control algorithm was framed in MATLAB with modified multilevel space vector pulse width modulator. The effectiveness of the entire ac motor drives system was tested. Simulation results are given in detail to show symmetrical and asymmetrical, power sharing conditions. Furthermore, the three degree of freedom are exploited to investigate fault tolerant capabilities in post-fault conditions. Complete set of simulation results are provided when one, two and three VSIs are faulty. Hardware prototype model of quad-inverter was implemented with two passive three-phase open-winding loads using two TMS320F2812 DSP controllers. Developed McBSP (multi-channel buffered serial port) communication algorithm able to control the four VSIs for PWM communication and synchronization. Open-loop control scheme based on inverse three-phase decomposition approach was developed to control entire quad-inverter configuration and tested with balanced and unbalanced operating conditions with simplified PWM techniques. Both simulation and experimental results are always in good agreement with theoretical developments.

Peak-to-Peak Output Current Ripple Analysis in Multiphase and Multilevel Inverters

Analysis of the peak-to-peak output current ripple amplitude for multiphase and multilevel inverters is presented in this PhD thesis. The current ripple is calculated on the basis of the alternating voltage component, and peak-to-peak value is defined by the current slopes and application times of the voltage levels in a switching period. Detailed analytical expressions of peak-to-peak current ripple distribution over a fundamental period are given as function of the modulation index. For all the cases, reference is made to centered and symmetrical switching patterns, generated either by carrier-based or space vector PWM. Starting from the definition and the analysis of the output current ripple in three-phase two-level inverters, the theoretical developments have been extended to the case of multiphase inverters, with emphasis on the five- and seven-phase inverters. The instantaneous current ripple is introduced for a generic balanced multiphase loads consisting of series RL impedance and ac back emf (RLE). Simplified and effective expressions to account for the maximum of the output current ripple have been defined. The peak-to-peak current ripple diagrams are presented and discussed. The analysis of the output current ripple has been extended also to multilevel inverters, specifically three-phase three-level inverters. Also in this case, the current ripple analysis is carried out for a balanced three-phase system consisting of series RL impedance and ac back emf (RLE), representing both motor loads and grid-connected applications. The peak-to-peak current ripple diagrams are presented and discussed. In addition, simulation and experimental results are carried out to prove the validity of the analytical developments in all the cases. The cases with different phase numbers and with different number of levels are compared among them, and some useful conclusions have been pointed out. Furthermore, some application examples are given.

Studio, simulazione e verifica sperimentale di tecniche di controllo per convertitori multilivello modulari

L’evoluzione dei componenti elettronici di potenza ed il conseguente sviluppo dei convertitori statici dell’energia elettrica hanno consentito di ottenere un’elevata efficienza energetica, sia nell’ambito degli azionamenti elettrici, sia nell’ambito della trasmissione e distribuzione dell’energia elettrica. L’efficienza energetica è una questione molto importante nell’attuale contesto storico, in quanto si sta facendo fronte ad una elevatissima richiesta di energia, sfruttando prevalentemente fonti di energia non rinnovabili. L’introduzione dei convertitori statici ha reso possibile un notevolissimo incremento dello sfruttamento delle fonti di energia rinnovabili: si pensi ad esempio agli inverter per impianti fotovoltaici o ai convertitori back to back per applicazioni eoliche. All’aumentare della potenza di un convertitore aumenta la sua tensione di esercizio: le limitazioni della tensione sopportabile dagli IGBT, che sono i componenti elettronici di potenza di più largo impiego nei convertitori statici, rendono necessarie modifiche strutturali per i convertitori nei casi in cui la tensione superi determinati valori. Tipicamente in media ed alta tensione si impiegano strutture multilivello. Esistono più tipi di configurazioni multilivello: nel presente lavoro è stato fatto un confronto tra le varie strutture esistenti e sono state valutate le possibilità offerte dall’architettura innovativa Modular Multilevel Converter, nota come MMC. Attualmente le strutture più diffuse sono la Diode Clamped e la Cascaded. La prima non è modulare, in quanto richiede un’apposita progettazione in relazione al numero di livelli di tensione. La seconda è modulare, ma richiede alimentazioni separate e indipendenti per ogni modulo. La struttura MMC è modulare e necessita di un’unica alimentazione per il bus DC, ma la presenza dei condensatori richiede particolare attenzione in fase di progettazione della tecnica di controllo, analogamente al caso del Diode Clamped. Un esempio di possibile utilizzo del convertitore MMC riguarda le trasmissioni HVDC, alle quali si sta dedicando un crescente interesse negli ultimi anni.