Application of the Williams-Landel-Ferry model to the viscosity-temperature relationship of Australian honeys

The rheological behaviour of nine unprocessed Australian honeys was investigated for the applicability of the Williams-Landel-Ferry (WLF) model. The viscosity of the honeys was obtained over a range of shear rates (0.01-40 s(-1)) from 2degrees to 40 degreesC, and all the honeys exhibited Newtonian behaviour with viscosity reducing as the temperature was increased. The honeys with high moisture were of lower viscosity, The glass transition temperatures of the honeys, as measured with a differential scanning calorimeter (DSC), ranged from -40degrees to -46 degreesC, and four models (WLF. Arrhenius, Vogel-Tammann-Fulcher (VTF), and power-law) were investigated to describe the temperature dependence of the viscosity. The WLF was the most suitable and the correlation coefficient averaged 0.999 +/- 0.0013 as against 0.996 +/- 0.0042 for the Arrhenius model while the mean relative deviation modulus was 0-12% for the WLF model and 10-40% for the Arrhenius one. With the universal values for the WLF constants, the temperature dependence of the viscosity was badly predicted. From non-linear regression analysis, the constants of the WLF models for the honeys were obtained (C-1 = 13.7-21.1: C-2 = 55.9-118.7) and are different from the universal values. These WLF constants will be valuable for adequate modeling of the rheology of the honeys, and they can be used to assess the temperature sensitivity of the honeys. (C) 2002 Elsevier Science Ltd. All rights reserved.

Leaf water relations of Eucalyptus cloeziana and Eucalyptus argophloia in response to water deficit

Leaf water relations responses to limited water supply were determined in 7-month-old plants of a dry inland provenance of Eucalyptus argophloia Blakely and in a humid coastal provenance (Gympie) and a dry inland provenance (Hungry Hills) of Eucalyptus cloeziana F. Muell. Each provenance of E. cloeziana exhibited a lower relative water content at the turgor loss point, a lower apoplastic water content, a smaller ratio of dry mass to turgid mass and a lower bulk modulus of elasticity than the single provenance of E. argophloia. Osmotic potential at full turgor and water potential at the turgor loss point were significantly lower in E. argophloia and the inland provenance of E. cloeziana than in the coastal provenance of E. cloeziana. There was limited osmotic adjustment in response to soil drying in E. cloeziana, but not in E. argophloia. Between-species differences in water relations parameters were larger than those between the E. cloeziana provenances. Both E. cloeziana provenances maintained turgor under moderate water stress through a combination of osmotic and elastic adjustments. Eucalyptus argophloia had more rigid cell walls and reached lower water potentials with less reduction in relative water content than either of the E. cloeziana provenances, thereby enabling it to extract water from dryer soils.

Modelling the size of the crushed zone around a blasthole

A new model to predict the extent of crushing around a blasthole is presented. The model is based on the back-analysis of a comprehensive experimental program that included the direct measurement of the zone of crushing from 92 blasting tests on concrete blocks using two commercial explosives. The concrete blocks varied from low, medium to high strength and measured 1.5 in in length, 1.0 m in width and 1.1 m in height. A dimensionless parameter called the crushing zone index (CZI) is introduced. This index measures the crushing potential of a charged blasthole and is a function of the borehole pressure, the unconfined compressive strength of the rock material, dynamic Young's modulus and Poisson's ratio. It is shown that the radius of crushing is a function of the CZI and the blasthole radius. A good correlation between the new model and measured results was obtained. A number of previously proposed models could not approximate the conditions measured in the experimental work and there are noted discrepancies between the different approaches reviewed, particularly for smaller diameter holes and low strength rock conditions. The new model has been verified with full scale tests reported in the literature. Results from this validation and model evaluations show its applicability to production blasting. (C) 2003 Elsevier Science Ltd. All rights reserved.

Relationships and estimates of longitudinal growth stress in Eucalyptus dunnii at different ages

O objetivo desse trabalho foi obter estimativas da tensão de crescimento longitudinal em árvores vivas e verificar a sua relação com algumas características da madeira de Eucalyptus dunnii Maiden aos oito, treze, quinze e dezenove anos de idade. O material foi proveniente da Empresa Procopiak Compensados e Embalagens S.A., localizada no Município de Canoinhas, Santa Catarina. Os níveis de tensão longitudinal de crescimento foram mensurados indiretamente pelo método do "CIRAD-Forêt", na árvore viva, e estimados a partir do módulo de elasticidade dinâmico e do módulo de elasticidade obtido no ensaio de tração paralela à grã. A deformação residual longitudinal (DRL) e as estimativas das tensões de crescimento longitudinais apresentaram tendência de aumento, na média, com a idade do material. A DRL apresentou correlação, positiva e significativa, com todas as estimativas das tensões de crescimento longitudinais, sendo de maior magnitude aos 13, 15 e 19 anos de idade. A densidade básica apresentou maiores correlações, positivas e significativas, com o módulo de elasticidade dinâmico, estimado no sentido longitudinal, para a madeira na condição de saturação e a 12% de umidade, em todas as idades avaliadas. Todas as estimativas das tensões de crescimento longitudinais apresentam elevadas correlações, positivas e significativas, entre si.

Influência da idade e da posição radial na flexão estática da madeira de Eucalyptus grandis Hill ex. Maiden

Este trabalho objetivou testar a variação da flexão estática da madeira de Eucalyptus grandis, ao longo da seção radial e sob quatro diferentes idades (10, 14, 20 e 25 anos), provenientes de talhões comerciais. As amostras foram retiradas da prancha diametral, de cada uma das 16 árvores (quatro para cada idade), tomadas de quatro posições eqüidistantes (0, 33, 66 e 100%), no sentido medula-casca, com oito repetições por posição. Verificou-se que os módulos de elasticidade (MOE) e de ruptura (MOR) apresentaram valores médios de 129.230 kgf/cm2 e 854 kgf/cm2, respectivamente, e ambos se mostraram positivamente correlacionados com a idade e com a posição radial, no sentido medula-casca. Os maiores valores foram conseguidos nas madeiras de 20 anos de idade e localizadas na região mais próxima da casca.

O sentido de ser professor de Educação Física pelos “modos de ser sendo junto ao outro no mundo” perverso- fascista e democrático: a vivência real & no filme “Má Educação”

Quais são os “modos de ser sendo junto ao outro no mundo” professores de Educação Física da Prefeitura Municipal da Serra, ES, situados no que se denomina “real” e do professor de Educação Física padre José no filme “Má Educação” de Pedro Almodóvar situado no que se denomina “ficcional”? Que contribuições reflexivas podem trazer tais dados (analisados hermeneuticamente) para a Formação Continuada de professores de Educação Física [3]? OBJETIVO: Descrever os “modos de ser sendo junto ao outro no mundo” de [1] professores de Educação Física que trabalham em escolas públicas da Prefeitura Municipal da Serra, ES & do [2] padre José, personagem ficcional, professor de Educação Física no filme espanhol de 2004 “Má Educação” fazendo-o primeiramente através de uma pesquisa clássica (descritiva e hermenêutica) e depois uma literaturalizada e artística (hermenêutica). MARCO TEÓRICO: Trata-se de uma proposta discursiva (teórica) fenomenológica existencial de tendência marxista criada por Pinel; METODOLOGIA: Tratou-se de uma pesquisa fenomenológica existencial seguindo recomendações de Forghieri (2001) e Pinel (2006; 2012) - dentre outros. Os 29 professores de Educação Física foram provocados a mostrarem os seus “modos de ser sendo junto ao outro no mundo” do ofício professor de Educação Física. Depois essa mesma provocação foi feita ao personagem do filme. RESULTADOS & DISCUSSÃO: Descreveram-se [1] os “modos de ser sendo junto ao outro no mundo” dos professores de Educação Física na dimensão do real e do ficcional (cinema), e não se objetivou comparação por mais que isso tenha ficado evidente. Esses professores, em 2011/2012, experienciando uma democracia (im)perfeita brasileira [que tem até tendências neofascistas], mais ainda assim democracia - foram compreendidos sempre tomando um norte/ rumo/ direção em subjetivação pelos Guias de Sentido (GS – Pinel) democráticos reconhecimento [demanda do grupo em ser valorizado, reconhecido], em (im) potência [impotência e potencia possível de vir a lume sempre; a força e seu outro lado, a fragilidade de ser], afetando [o que se pratica e pensa/sente afeta a si mesmo, o outro e o mundo; o afetar produz mais subjetivações], sonhando [há demanda sempre de realizar projetos de vida; o projeto de ser sempre devir, em construção sempre; é uma precisão imprecisa], saudavelmente insano [o quão perto pode estar a experienciar a sanidade e a loucura e o quanto uma loucura é sã, pois criativa, inventiva, produtiva, opositora ao estabelecido] – eles mesmos junto ao outro no mundo tornando-se sujeitos. [2] Já o professor de Educação Física padre José da película almodovariana é um professor que de imediato pode ser apreendido como sólido e fixo na sua perversão fascista, ele como parte legitimadora do Estado espanhol de Franco, na década de 60, provavelmente em 1964, que é, na ficção, o espaço-tempo de José e suas ações pedagógicas e psicológicas (e de Educação Física). Mas não é apenas o fascismo que torna o fascista um criador de um cotidiano fascista, pois afinal, paralelamente a ele, no concreto e na ficção, haviam pessoas generosas, resistentes e resilientes que atuavam contra essas pressões quase na maioria das vezes advindas do todo (Estado) – eram pessoas democráticas individualmente e em pequenos e grandes grupos; eram exemplo de resistência contra o estabelecido pela ideologia dominante de então. José numa instituição fascista não conseguiu refletir e agir diferentemente, isto é, com mais saúde mental, escolhendo (na liberdade) ser fascista, ser menor (pouco) – optou não ser-mais. Finalmente os mesmos dados são apresentados em outra estética possível e sempre aberta, inconclusa, devir... As artes e a poesia (bem como a literatura) procuram cuidadosamente desvelar os “modos de ser junto ao outro no mundo” professor de Educação Física do mundo real e do imaginário (fílmico) desvelando muitas vezes indissociados. PÓSCRITO: O autor descreve as possíveis implicações do seu estudo para educação física pautado sempre em uma proposta de criar um discursso insubmisso focando na ideia de que uma pesquisa demanda narrar a vida, e literaturalizar a ciência.

Estudo do efeito da face sobre o equilíbrio de estruturas de contenção de solo reforçado sob condições de trabalho

Os métodos de análise de estruturas de contenção de solo reforçado sob condições de trabalho, em geral, desconsideram a contribuição da face para o equilíbrio da estrutura. Visando estudar a influência do peso específico da face e das propriedades relacionadas à rigidez da mesma sobre o desempenho das estruturas de solo reforçado, são realizadas simulações numéricas de diversas estruturas, utilizando a versão de dupla precisão do programa CRISP92-SC. Avalia-se, também, o emprego de diferentes tipos de elementos para a representação da face. Verifica-se que a face rígida impõe redução significativa das solicitações máximas de tração nos reforços e dos deslocamentos das estruturas de solo reforçado. A influência do peso específico da face sobre a estabilidade interna dos maciços reforçados mostrase desprezível e constata-se que a rigidez à flexão e a rigidez axial da face, função da sua geometria e do seu módulo de Young, são parâmetros influentes no comportamento das estruturas de contenção de solo reforçado. As variações da tração no reforço e da resultante de força cortante na face, em decorrência do enrijecimento da face, são analisadas e propõe-se uma relação entre elas. Quanto à forma de representação de uma face com rigidez expressiva, na simulação de uma estrutura de solo reforçado com o CRISP92-SC, é observado que a representação da face, seja por elementos de viga, seja por elementos quadriláteros, não altera os resultados da análise.

Processing and characterization of alpha-elastin electrospun membranes

Elastin isolated from fresh bovine ligaments was dissolved in a mixture of 1,1,1,3,3,3-Hexafluoro-2-propanol and water and electrospun into fiber membranes under different processing conditions. Fiber mats of randomly and aligned fibers were obtained with fixed and rotating ground collectors and fibrils were composed by thin ribbons whose width depends on electrospinning conditions; fibrils with 721 nm up to 2.12 m width were achieved. After cross-linking with glutaraldehyde, -elastin can uptake as much as 1700 % of PBS solution and a slight increase on fiber thickness was observed. The glass transition temperature of electrospun fiber mats was found to occur at ~ 80 ºC. Moreover, -Elastin showed to be a perfect elastomeric material, and no mechanical hysteresis was found in cycle mechanical measurements. The elastic modulus obtained for oriented and random fibers mats in a PBS solution was 330 ± 10 kPa and 732 ± 165 kPa, respectively. Finally, the electrospinning and cross-linking process does not inhibit MC-3T3-E1 cell adhesion. Cell culture results showed good cell adhesion and proliferation in the cross-linked elastin fiber mats.

Electrospun silk-elastin-like fiber mats for tissue engineering applications

Protein-based polymers are present in a wide variety of organisms fulfilling structural and mechanical roles. Advances in protein engineering and recombinant DNA technology allow the design and production of recombinant protein-based polymers (rPBPs) with an absolute control of its composition. Although the application of recombinant proteins as biomaterials is still an emerging technology, the possibilities are limitless and far superior to natural or synthetic materials, as the complexity of the structural design can be fully customized. In this work, we report the electrospinning of two new genetically engineered silk-elastin-like proteins (SELPs) consisting of alternate silk- and elastin-like blocks. Electrospinning was performed with formic acid and aqueous solutions at different concentrations without addition of further agents. The size and morphology of the electrospun structures was characterized by scanning electron microscopy showing to be dependent of concentration and solvent used. Treatment with air saturated with methanol was employed to stabilize the structure and promote water insolubility through a time-dependent conversion of random coils into β-sheets (FTIR). The resultant methanol-treated electrospun mats were characterized for swelling degree (570-720%), water vapour transmission rate (1083 g/m2/day) and mechanical properties (modulus of elasticity of ~126 MPa). Furthermore, the methanol-treated SELP fiber mats showed no cytotoxicity and were able to support adhesion and proliferation of normal human skin fibroblasts. Adhesion was characterized by a filopodia-mediated mechanism. These results demonstrate that SELP fiber mats can provide promising solutions for the development of novel biomaterials suitable for tissue engineering applications.

Thermomechanical environment characterisation in injection moulding and its relation to the mechanical properties of talc-filled polypropylene

This study is focused on the establishment of relationships between the injection moulding processing conditions, the applied thermomechanical environment (TME) and the tensile properties of talc-filled polypropylene,adopting a new extended concept of thermomechanical indices (TMI). In this approach, TMI are calculated from computational simulations of the moulding process that characterise the TME during processing, which are then related to the mechanical properties of the mouldings. In this study, this concept is extended to both the filling and the packing phases, with new TMI defined related to the morphology developed during these phases. A design of experiments approach based on Taguchi orthogonal arrays was adopted to vary the injection moulding parameters (injection flow rate, injection temperature, mould wall temperature and holding pressure), and thus, the TME. Results from analysis of variance for injection-moulded tensile specimens have shown that among the considered processing conditions, the flow rate is the most significant parameter for the Young’s modulus; the flow rate and melt temperature are the most significant for the strain at break; and the holding pressure and flow rate are the most significant for the stress at yield. The yield stress and Young’s modulus were found to be governed mostly by the thermostress index (TSI, related to the orientation of the skin layer), whilst the strain at break depends on both the TSI and the cooling index (CI, associated to the crystallinity degree of the core region). The proposed TMI approach provides predictive capabilities of the mechanical response of injection-moulded components, which is a valuable input during their design stage.

Electro-mechanical properties of triblock copolymer styrene-butadiene-styrene / carbon nanotube composites for large deformation sensor applications

Thermoplastic elastomer/carbon nanotube composites are studied for sensor applications due to their excellent mechanical and electrical properties. Piezoresisitive properties of tri-block copolymer styrene-butadiene-styrene (SBS)/ carbon nanotubes (CNT) prepared by solution casting have been investigated. Young modulus of the SBS/CNT composites increases with the amount of CNT filler content present in the samples, without losing the high strain deformation on the polymer matrix (~1500 %). Further, above the percolation threshold these materials are unique for the development of large deformation sensors due to the strong piezoresistive response. Piezoresistive properties evaluated by uniaxial stretching in tensile mode and 4-point bending showed a Gauge Factors up to 120. The excellent linearity obtained between strain and electrical resistance makes these composites interesting for large strain piezoresistive sensors applications.

Artificial neural networks for automatic modelling of the pectus excavatum corrective prosthesis

Pectus excavatum is the most common deformity of the thorax and usually comprises Computed Tomography (CT) examination for pre-operative diagnosis. Aiming at the elimination of the high amounts of CT radiation exposure, this work presents a new methodology for the replacement of CT by a laser scanner (radiation-free) in the treatment of pectus excavatum using personally modeled prosthesis. The complete elimination of CT involves the determination of ribs external outline, at the maximum sternum depression point for prosthesis placement, based on chest wall skin surface information, acquired by a laser scanner. The developed solution resorts to artificial neural networks trained with data vectors from 165 patients. Scaled Conjugate Gradient, Levenberg-Marquardt, Resilient Back propagation and One Step Secant gradient learning algorithms were used. The training procedure was performed using the soft tissue thicknesses, determined using image processing techniques that automatically segment the skin and rib cage. The developed solution was then used to determine the ribs outline in data from 20 patient scanners. Tests revealed that ribs position can be estimated with an average error of about 6.82±5.7 mm for the left and right side of the patient. Such an error range is well below current prosthesis manual modeling (11.7±4.01 mm) even without CT imagiology, indicating a considerable step forward towards CT replacement by a 3D scanner for prosthesis personalization.

SUPPLY CHAIN RESILIENCE ANALYSIS: A BRAZILIAN AUTOMOTIVE CASE

Supply chain (SC) resilience and flexibility are important research topics receiving growing attention. However, the academic literature needs empirical studies on SC resilience capable of investigating the inter-organizational components of flexibility along different tiers. Therefore, this paper analyzes the main lack of flexibilities in three Brazilian automotive SCs that limit their resilience and therefore their capacity to better support and meet the demand changes in the marketplace. A multi-tier case study approach is adopted. Research findings identify lack of flexibilities in different tiers that inhibit the SC resilience as well as manufacturing and SC flexibilities that build SC resilience. The findings also highlight that the same SC may have the flexibility to be resilient for one of its products but not for another product, what sheds new lights on the academic literature. Finally, flexible SCs should be designed to increase SC resilience to cope with mishaps as significant demand changes.

Reversible Photorheology in Solutions of Cetyltrimethylammonium Bromide, Salicylic Acid, and trans-2,4,4 '-Trihydroxychalcone

We show photorheology in aqueous solutions of weakly entangled wormlike micelles prepared with cetyltrimethylammonium bromide (CTAB), salicylic acid (HSal), and dilute amounts of the photochromic multistate compound trans-2,4,4'-trihydroxychalcone (Ct). Different chemical species of Ct are associated with different colorations and propensities to reside within or outside CTAB micelles. A light-induced transfer between the intra- and intermicellar space is used to alter the mean length of wormlike micelles and hence the rheological properties of the fluid, studied in steady-state shear Bow and in dynamic rheological measurements. Light-induced changes of fluid rheology are reversible by a the relaxation process. at relaxation rates which depend on pH and which are consistent with photochromic reversion rates measured by UV-vis absorption spectroscopy. Parameterizing viscoelostic rheological states by their effective relaxation time tau(c) and corresponding response modulus G(c), we find the light and dark states of the system to fall onto a characteristic state curve defined by comparable experiments conducted without photosensitive components. These reference experiments were prepared with the same concentration of CTAB, but different concentrations of HSal or sodium salicylote (NaSal), and tested at different temperatures.

Durability performance of concrete made with fine recycled concrete aggregates

Fine recycled aggregates are seen as the last choice in recycling for concrete production. Many references quote their detrimental influence on the most important characteristics of concrete: compressive and tensile strength; modulus of elasticity; water absorption; shrinkage: carbonation and chloride penetration. These two last characteristics are fundamental in terms of the long-term durability of reinforced or prestressed concrete. In the experimental research carried out at IST, part of which has already been published, different concrete mixes (with increasing rates of substitution of fine natural aggregates sand - with fine recycled aggregates from crushed concrete) were prepared and tested. The results were then compared with those for a reference concrete with exactly the same composition and grading curve, but with no recycled aggregates. This paper presents the main results of this research for water absorption by immersion and capillarity, chloride penetration (by means of the chloride migration coefficient), and carbonation resistance, drawing some conclusions on the feasibility of using this type of aggregate in structural concrete, while taking into account any ensuing obvious positive environmental impact.