A study of performance characteristics of domestic water heating equipment, conducted for the Federal Housing Administration under contract no. HA-fh-646 (amendment no. 1) May 10, 1956 /

Mode of access: Internet.

Performance of resurfacing of JRCP and CRCP on the Illinois interstate highway system /

"Project IHR-517, Illinois Cooperative Highway Research Program."

Minimal manoeuvres of high performance aircraft in a vertical plane.

On cover: Purdue Research Foundation. Research project no.1255. Project Ae-25.

Vehicle classification case study for the highway performance monitoring system /

Chiefly tables.

Projectile Combustion Effects on Ram Accelerator Performance

Thesis (Master's)--University of Washington, 2016-06

Effects of Shallow Bi-Angle, Thin-Ply Laminates on the Structural Performance of Composite Wings

Thesis (Master's)--University of Washington, 2016-06

Development of Cookstove Emissions and Performance Testing Suite with Time-resolved Particulate Matter Analysis and Excess Air Estimation

Thesis (Master's)--University of Washington, 2016-06

Performance of hydrophobic and hydrophilic silica membrane reactors for the water gas shift reaction

In this study, a novel molecular sieve silica (MSS) membrane packed bed reactor (PBR) using a Cu/ZnO/Al2O3 catalyst was applied to the low-temperature water gas shift reaction (WGS). Best permeation results were H-2 permeances of 1.5 x 10(-6) mol(.)s(-1) m(-2) Pa-1, H-2/CO2 selectivities of 8 and H-2/N-2 selectivities of 18. It was shown that an operation with a sweep gas flow of 80 cm 3 min(-1), a feed flow rate of 50 cm(3) min(-1) and a H2O/CO molar ratio of one at 280 degreesC reached a 99% CO conversion. This is well above the thermodynamic equilibrium and achievable PBR conversion. Hydrophilic membranes underwent pore widening during the reaction while hydrophobic membranes indicated no such behaviour and also showed increased H-2 permeation with temperature, a characteristic of activated transport. (C) 2003 Elsevier Science B.V. All rights reserved.

Parameters affecting the performance of wetting and drying in a two-dimensional finite element long wave hydrodynamic model

The marsh porosity method, a type of thin slot wetting and drying algorithm in a two-dimensional finite element long wave hydrodynamic model, is discussed and analyzed to assess model performance. Tests, including comparisons to simple examples and theoretical calculations, examine the effects of varying the marsh porosity parameters. The findings demonstrate that the wetting and drying concept of marsh porosity, often used in finite element hydrodynamic modeling, can behave in a more complex manner than initially expected.

Understanding magnesium corrosion - A framework for improved alloy performance

The purpose of this paper is to provide a succinct but nevertheless complete mechanistic overview of the various types of magnesium corrosion. The understanding of the corrosion processes of magnesium alloys builds upon our understanding of the corrosion of pure magnesium. This provides an understanding of the types of corrosion exhibited by,magnesium alloys, and also of the environmental factors Of most importance. This deep understanding is required as a foundation if we are to produce magnesium alloys much more resistant to corrosion than the present alloys. Much has already been achieved, but there is vast scope for improvement. This present analysis can provide a foundation and a theoretical framework for further, much needed research. There is still vast scope both for better fundamental understanding of corrosion processes, engineering usage of magnesium, and also on the corrosion protection of magnesium alloys in service.

Performance of improved guayule lines in Australia

Guayule (Parthenium argentatum Gray) is a potential source of commercial natural rubber. Its commercialisation depends mainly on economical plant production. The objective of this study was to evaluate the performance of improved lines in Australia. Seeds from five improved lines (AZ-1, AZ-2, AZ-3, AZ-5 and AZ-6) and two previously developed guayule lines (N 565 and 11591) were obtained from the Agricultural Research Service (ARS) of the United States Department of Agriculture (USDA). Seedlings from these lines were grown in a glasshouse for 3 months and later transplanted in a field experiment in early September 2001. Plant height and width were monitored from transplanting to 62 weeks at regular intervals. After 62 weeks, plant dry matter production, rubber and resin content, and yields were analysed. Plant height and width of the improved lines were higher than N 565 and 11591. Plant dry matter, rubber and resin yields were significantly different among lines. Of the five lines, AZ-1 and AZ-2 produced rubber yields of 620 and 550 kg/ha, respectively and these yields were significantly greater than for N 565 (371 kg/ha) and 11591 (391 kg/ha). AZ-1 and AZ-2 also produced significantly higher resin yields, 727 and 668 kg/ha, respectively, than those for N 565 (436 kg/ha) and 11591 (325 kg/ha). Rubber and resin yield increase of lines, AZ-1 and AZ-2, were in the range of 41-68% and 53-123%, respectively over N 565 and 11591. AZ-1 tended to produce higher rubber and resin yields than AZ-2 but exhibited highly variable plant height (CV = 25%) and width (CV = 41%) indicating potential for further genetic improvement. AZ-2 offers the best combination of desirable characters including early vigour, uniformity and comparatively higher rubber and resin yields. (C) 2003 Published by Elsevier B.V.

Improvement of compact terminal antenna performance by incorporating open-end slots in ground plane

This letter describes a new idea of increasing operational bandwidth of a compact planar inverted F antenna (PIFA) by introducing open-end slots in the ground plane under the radiating patch. The slots are not in the way of active modules of a wireless transceiver and thus the proposed antenna size reduction method is attractive from the point of view of practical implementation.

Effects of hydrogen-air non-equilibrium chemistry on the performance of a model scramjet thrust nozzle

Two aspects of hydrogen-air non-equilibrium chemistry related to scramjets are nozzle freezing and a process called 'kinetic afterburning' which involves continuation of combustion after expansion in the nozzle. These effects were investigated numerically and experimentally with a model scramjet combustion chamber and thrust nozzle combination. The overall model length was 0.5m, while precombustion Mach numbers of 3.1 +/- 0.3 and precombustion temperatures ranging from 740K to 1,400K were involved. Nozzle freezing was investigated at precombustion pressures of 190kPa and higher, and it was found that the nozzle thrusts were within 6% of values obtained from finite rate numerical calculations, which were within 7% of equilibrium calculations. When precombustion pressures of 70kPa or less were used, kinetic afterburning was found to be partly responsible for thrust production, in both the numerical calculations and the experiments. Kinetic afterburning offers a means of extending the operating Mach number range of a fixed geometry scramjet.

Enhancing student performance through cooperative learning in physical sciences

Students in a physical sciences course were introduced to cooperative learning at the University of Queensland, Gatton Campus. Groups of four to five students worked together in tutorial and practical sessions. Mid-term and practical examinations were abolished and 40% of total marks were allocated to the cooperative learning activities. A peer- and self-assessment system was successfully adapted to account for individual performance in cooperative learning group assignments. The results suggest that cooperative learning was very well received by students, and they expressed willingness to join cooperative learning groups in other courses. In addition, cooperative learning offered many benefits to students in terms of graduate attributes such as teamwork, communication, lifelong learning and problem-solving.