Envelhecimento ambiental acelerado em PRF a base de tecidos híbridos kevlar/vidro: propriedades e instabilidade estrutural

There are a number of damaging mechanisms that various materials can suffer in service. However, when working with polymer composite materials, this is something that requires analysis, especially when exposed to adverse environmental conditions. Thus, the objective of the present thesis is the study of the direct influence of environmental aging and the form of hybridization of the reinforcement woven on the structural stability, surfacedegradation and fracture process of polymer composites laminates. For this, the development of two polymer composite laminates was necessary, where one of them was reinforced with a bi-directional woven with hybrid strandsofkevlar-49/glass-Efibers, and the other also with a bi-directionalwoven, however with weft and warpformed of alternating strandsof Kevlar-49 fibers and glass-E fiber The reinforcementwoven are industrially manufactured. Both laminates use a polyester resin as a matrixand are made up of four layers each. All laminates were industrially prepared by the hand lay-up method of manufacturing. To do this, test specimens were manufactured of the respective laminates and submitted to environmental aging accelerated through the aging chamber. They were exposed to alternating cycles of UV radiation and moisture (heated steam) for a standard defined period. At the end of the exposure period the specimens were subjected to mechanical tests of uniaxial tensile and bending in three points and to the characterizationsof the fracture and surface deterioration. In addition, they were submitted to a structural degradation assessment by the measurement of mass variation technique (MMVT) and the measurement of thickness variation technique (MTVT), this last technique being developed in this thesis. At the end of the analysis it was observed that the form of hybridization of the reinforcement woven and the aging process directly influence with losses or gain in mechanical properties, with losses in the structural degradation and in the formation and propagation of damage mechanism of the developedcomposite laminates

Desempenho mecânico de compósitos híbridos de fibras naturais e poliéster não saturado

With the objective to promote sustainable development, the fibres found in nature in abundance, which are biodegradable, of low cost in comparison to synthetic fibres are being used in the manufacture of composites. The mechanical behavior of the curauá and pineapple leaf fibre (PALF) composites in different proportions, 25% x 75% (P1), 50% x 50% (P2) e 75% x 25% (P3) were respectively studied, being initially treated with a 2% aqueous solution of sodium hydroxide. Mechanical analyses indicated that with respect to studies of traction, for the combination of P1 and P3, better results of 22.17 MPa and 16.98 MPa, were obtained respectively, which are higher than that of the combination P2. The results of the same pattern were obtained for analysis of bending resistance where P1 is 1.21% and P3 represents 0.96%. In the case of resistance to bending, best results were obtained for the combination P1 at 49.07 MPa. However, when Young's modulus values were calculated, the values were different to the pattern of the results of other tests, where the combination P2 with the value of 4.06 GPa is greater than the other combinations. This shows that the PALF had a greater influence in relation to curauá fibre. The analysis of the results generally shows that in combinations of two vegetable fibers of cellulosic origin, the fiber which shows higher percentage (75%) is the best option than to the composition of 50%/50%. In the meantime, according to the results obtained in this study, in the case where the application should withstand bending loads, the better composition would be 50%/50%

Estudo da presença de entalhes semicirculares em compósitos poliméricos híbridos

Composite materials have a wide application in various sectors, such as the medical field in the manufacture of prostheses, in automotive and aerospace. Thus it is essential to the development of new composite and a better understanding in the face of various loading conditions and service. Several structural elements are manufactured in the presence of geometric discontinuity (notch, hole, etc ) in their longitudinal sections and/or cross-cutting, and these affect the mechanical response of these elements. The objective is to study the mechanical response of laminated polymer matrix hybrid composites reinforced with glass fiber/jute in a uniaxial tensile test. The mechanical response takes in account both the influence of the presence of a geometric discontinuity (semicircular notches) and the orientation of fibers in the layers (anisotropy). The semicircular notches are located in longitudinal section (with a reduction in cross section) of the same. In this analysis, the anisotropy is characterized by types of configurations (with different orientations of fibers in the outer layers). A comparative study of mechanical properties with and without the presence of notches is developed. Both configurations consist of four layers of woven jute fiber bidirectional and a central layer of bidirectional woven glass fibers. In addition to the mechanical properties was also studied the characteristics of the fracture developed in each composite laminate. The results showed that in the comparative study, the anisotropy and the presence of semicircular notches directly influences the mechanical behavior of laminates composites, mainly in reducing the tensile strength, and well as the final characteristics of the fracture

Análise aerodinâmica de perfis de asa para aeronaves experimentais tipo jn-1

The great importance in selecting the profile of an aircraft wing concerns the fact that its relevance in the performance thereof; influencing this displacement costs (fuel consumption, flight level, for example), the conditions of flight safety (response in critical condition) of the plane. The aim of this study was to examine the aerodynamic parameters that affect some types of wing profile, based on wind tunnel testing, to determine the aerodynamic efficiency of each one of them. We compared three types of planforms, chosen from considerations about the characteristics of the aircraft model. One of them has a common setup, and very common in laboratory classes to be a sort of standard aerodynamic, it is a symmetrical profile. The second profile shows a conFiguration of the concave-convex type, the third is also a concave-convex profile, but with different implementation of the second, and finally, the fourth airfoil profile has a plano-convex. Thus, three different categories are covered in profile, showing the main points of relevance to their employment. To perform the experiment used a wind tunnel-type open circuit, where we analyzed the pressure distribution across the surface of each profile. Possession of the drag polar of each wing profile can be, from the theoretical basis of this work, the aerodynamic characteristics relate to the expected performance of the experimental aircraft, thus creating a selection model with guaranteed performance aerodynamics. It is believed that the philosophy used in this dissertation research validates the results, resulting in an experimental alternative for reliable implementation of aerodynamic testing in models of planforms

Comportamento de híbridos de couve chinesa à isolados de Plasmodiophora brassicae

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência da umidade nas propriedades mecânicas dos compósitos poliméricos híbridos (sisal/ vidro)

This study aims to evaluate the mechanical properties of polymer matrix composites reinforced with sisal fabric bidirectional tissue (Agave sisalana,) and E-glass fibers, containing the following configuration: a polymer matrix hybrid composite (Polyester Resin orthophalic) reinforced with three (3) layers of glass fibers and alternating-2 (two) layers of bidirectional sisal fabric, and finally a composite of polymer matrix reinforced with five (5) layers of glass fiber mat-type E. For this purpose as first step, the preparation of by sisal, since they are not on the market. The composites were made by manual lamination (Hand lay-up) and evaluated for tensile properties and three point bending both in the dry, and wet conditions aswele as immersed in oil. Macroscopic and microscopic characteristics of the materialsweve awalysed, after the completion of the mechanical tests. After the studies, it was proven that the sisal fiber decreases the tensile stiffness of the material above 50% for both situations studied the tensile strength of the material decreases by approximately 40% for the cases mentioned, and when compared to the specific strength stiffness values drop to 14.6% and 29.02% respectively for the dry state only. Constants for bending the values were are to approximately 50% to 25% for strength and stiffness of the material for the cases dry, wet and immersed in oil. Under the influence of tension fluids do not interfere in the stiffness of the material for the bending tests, the same does not occur with the resistance, and these values are modified only in the cases stiffness and flexural strength

Desenvolvimento de perfis aerodinâmicos a partir de suas características utilizando redes neurais artificiais

One of the current major concerns in engineering is the development of aircrafts that have low power consumption and high performance. So, airfoils that have a high value of Lift Coefficient and a low value for the Drag Coefficient, generating a High-Efficiency airfoil are studied and designed. When the value of the Efficiency increases, the aircraft s fuel consumption decreases, thus improving its performance. Therefore, this work aims to develop a tool for designing of airfoils from desired characteristics, as Lift and Drag coefficients and the maximum Efficiency, using an algorithm based on an Artificial Neural Network (ANN). For this, it was initially collected an aerodynamic characteristics database, with a total of 300 airfoils, from the software XFoil. Then, through the software MATLAB, several network architectures were trained, between modular and hierarchical, using the Back-propagation algorithm and the Momentum rule. For data analysis, was used the technique of cross- validation, evaluating the network that has the lowest value of Root Mean Square (RMS). In this case, the best result was obtained for a hierarchical architecture with two modules and one layer of hidden neurons. The airfoils developed for that network, in the regions of lower RMS, were compared with the same airfoils imported into the software XFoil

Envelhecimento ambiental em compósitos poliméricos à base de tecidos de reforços híbridos

The utilization of synthetic fibers for plastic reinforcement is more and more frequent and this growing interest requires that their mechanic behavior under the most variable conditions of structural applications be known. The use of such materials in the open and exposed to the elements is one of them. In this case, it becomes extremely necessary to study their mechanical properties (strength, stiffness) and the mechanism of fracture by which the environment aging them out. In order to do that, the material must be submitted to hot steam and ultraviolet radiation exposure cycles, according to periods of time determined by the norms. This study proposal deals with the investigation of accelerated environmental aging in two laminated polymeric composites reinforced by hybrid woven made up of synthetic fibers. The configurations of the laminated composites are defined as: one laminate reinforced with hybrid woven of glass fibers/E and Kevlar fibers/49 (LHVK) and the other laminate is reinforced with hybrid tissue of glass fibers/E and of carbon fibers AS4 (LHVC). The woven are plane and bidirectional. Both laminates are impregnated with a thermofix resin called Derakane 470-300 Epoxy Vinyl-Ester and they form a total of four layers. The laminates were industrially manufactured and were made through the process of hand-lay-up. Comparative analyses were carried out between their mechanical properties by submitting specimen to uniaxial loading tractions and three-point flexion. The specimen were tested both from their original state, that is, without being environmentally aging out, and after environmental aging. This last state was reached by using the environmental aging chamber

Perfis de distribuição volumétrica de pontas XR 11003 e TXVK-4 em diferentes condições de pulverização

Com o objetivo de avaliar a uniformidade da distribuição volumétrica e o efeito da angulação dos bicos na barra em pulverizações, foi conduzido experimento em laboratório, com dez unidades de cada uma das pontas de jato plano XR 11003 e de jato cônico vazio TXVK-4, fabricadas pela Spraying Systems Co. As pontas XR 11003 foram avaliadas, isoladamente, em mesa de prova para bicos construída conforme a Norma ISO 5682-1:1996, a 0,30; 0,40 e 0,50 m de altura, submetidas à pressão de 200 e 300 kPa e posicionadas com ângulos de 30º e 45º no sentido horário e anti-horário e na vertical; as pontas TXVK-4 foram avaliadas nas mesmas alturas, porém a 300 e 400 kPa, e somente na vertical. A distribuição média do volume coletado em cada configuração, das dez unidades de cada ponta, foi inserida num programa computacional, desenvolvido para o estudo, que permitiu a simulação do padrão de deposição de uma barra pulverizadora, com 24 bicos, com sobreposições variáveis, obtendo-se, ao final, o coeficiente de variação da sobreposição, o desvio- padrão e a média do volume aplicado. Os resultados sugerem a necessidade de ajustes no espaçamento entre bicos para a obtenção de melhor uniformidade na distribuição, principalmente quando se utiliza ângulo na barra; há menor influência da variação da altura da barra sobre a uniformidade da distribuição quando o espaçamento entre bicos é reduzido.

Avaliação de linhagens e híbridos experimentais de pepino do grupo varietal japonês sob ambiente protegido

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação de híbridos de girassol e relação entre parâmetros produtivos e qualitativos

O presente estudo teve o objetivo de determinar genótipos superiores de girassol, bem como realizar estudos de correlação entre suas características. Avaliou-se seis híbridos de girassol em condições de safrinha no município de Palotina - PR. O estudo avaliou quinze variáveis: massa seca de folhas, massa seca de caule e pecíolos, massa seca total, área foliar, altura de planta, diâmetro de colmo, massa de grãos por capítulo, diâmetro de capítulo, percentagem de grãos normais, massa de mil grãos, número de grãos por capítulo, produtividade, teor de proteína bruta, teor de óleo e rendimento de óleo. Os dados direcionam os híbridos H360 e MG2 com boa produtividade e maior teor de óleo para a produção de óleo e os híbridos M734 e Aguará 3 para a alimentação animal, com boa produtividade e menor teor de óleo. As correlações entre produtividade e os componentes de produção foram de 0,62; 0,47; 0,60; 0,49 e 0,47 para massa de grãos por capítulo, diâmetro de capítulo, percentagem de grãos normais, massa de mil grãos e número de grãos por capítulo, respectivamente, concluindo que a seleção de materiais a partir desses componentes ocasionará a seleção de materiais promissores em produtividade.

Reação de híbridos de brócolis 'tipo cabeça única' à podridão negra

Conduziu-se simultaneamente dois experimentos, em casa de vegetação, com o objetivo de avaliar a resistência de híbridos de brócolis 'tipo cabeça única' (AF 649, Titleist, Centenário, Green Power, BR068, Magestic Crown, Marathon, Laguna, Legacy, Green Parasol, Packman e Mônaco) à podridão negra, causada por Xanthomonas campestris pv. campestris. Foram utilizados os métodos de inoculação no ápice das folhas por cortes com tesoura embebida na suspensão bacteriana e por ferimento provocado no caule com palito de dente umedecido na suspensão bacteriana. A inoculação foi realizada aos 25 dias após transplante (6 a 8 folhas definitivas). Avaliou-se no experimento de inoculação com tesoura, as áreas abaixo da curva de progresso da doença nas folhas inoculadas. No experimento de inoculação por palito de dente, avaliou-se a proporção de altura necrosada do caule, aos 26 dias após inoculação. Verificou-se que, em ambos os experimentos, o híbrido BRO68 apresentou-se mais suscetível à podridão negra e os híbridos Marathon, Legacy e Green Power foram os que apresentaram os maiores níveis de resistência à podridão negra.

Avaliação de sete famílias S2 prolíficas de minimilho para a produção de híbridos

Sete famílias S2 de minimilho foram cruzadas entre si em esquema dialélico completo. Os híbridos simples obtidos foram avaliados na Estação Experimental de São Manuel, da Faculdade de Ciências Agrárias da Universidade de São Paulo (UNESP-Botucatu). O experimento foi delineado em blocos casualizados com três repetições. As parcelas consistiram de fileiras de 5 m espaçadas entre si por 0,90 m, com 50 plantas cada uma. Avaliaram-se as seguintes características: número de espigas por parcela (NE), massa de espigas com palha (MECP) e sem palha (MESP), comprimento de espigas com palha (CECP) e sem palha (CESP), diâmetro de espigas com palha (DECP) e sem palha (DESP), altura da planta (AP) e da espiga (AE). Estimaram-se os efeitos da capacidade geral e específica de combinação das famílias pelo método 4, modelo estatístico 1, proposto por Griffing. Houve predominância dos efeitos gênicos aditivos para a massa de espigas com palha e sem palha. Entretanto, para o comprimento de espigas sem palha, diâmetro de espigas com palha e sem palha, altura de planta e altura de espigas, os efeitos gênicos aditivos e não aditivos foram equivalentes. Pelas estimativas das capacidades combinatórias para o número de espigas por parcela, massa de espigas com palha e sem palha, a família 27 é a indicada para obter genótipos superiores.

Formação Acadêmica em Educação Física: perfis profissionais, objetivos e fluxos curriculares.

In this research, characterized as a qualitative study, we aimed to analyze the Job Profiles, Objectives and Curriculum Flows specified in Pedagogical Projects of the undergraduate Courses of Physical Education of public, state and federal universities, in the São Paulo state. We also analyzed their articulations and adequacy to the Institutional Pedagogical Project and Institutional Development Plan. The latest Resolutions of Physical Education in Higher Education and conceptualizations of the Pedagogical Project of Course are presented. The method of approach is current History. There was a documental research in order to analyze the official documents. A limited offering of public courses when compared to private institutions was verified and also, there was a greater offering of bachelor degree courses (expanded and generalized formation) concerning health, sport and leisure fields. Courses defined specifically for teachers' formation and educational gap between the pedagogical discourses and the curriculum structures were also presented. In conclusion, this research indicates the necessity of a change in the curricular mentality in order to implement the pedagogical discourses of courses.

Adaptabilidade de híbridos entre Gossypium barbadense E G. hirsutum N contendo o gene cry1Ac

Hybrids among transgenic plants and related species are expected to occur if they are sympatric and when there are not crossing barriers; as is the case, in Brazil, of cry1Ac transgenic cotton and Gossypium barbadense. This species has been maintained as dooryard plants, and should be preserved as a genetic resource. Hybrids were evaluated about traits related to fitness, leading to infer about its chances of survivor and selection. A barbadense genotype collected at the state of Mato Grosso was outcrossed to the variety DP 404, containing the gene cry1Ac, and to the isoline DP 404. All the F1 individuals and 122 among 170 F2 individuals expressed the toxin, and presented levels of resistance to pink bollworm (Pectinophora gossypiella) and cotton leafworm (Alabama argillacea) equivalent to the transgenic parent and superior to the isoline, barbadense or non transgenic hybrids. The percentage of germination and number of days to germinate did not differ among genotypes. Anthesis of the first flower and opening of the first cotton boll occurred earlier for herbaceous cotton and F1 hybrids than F2 population in average; all the populations presented a number of days to flower and opening of the first boll smaller then barbadense. The highest plants were barbadenses, and herbaceus the smallest, with F1 and F2 populations presenting intermediary heights. The number of seeds per plants were superior for F1 hybrids an herbaceous cotton, F2 populations were in average intermediary; the barbadense genotype produced the smallest number of seeds per plant. Pink bollworm, mainly, and also cotton leafworm, are important barbadense pests, so the transgene positive effect could favor the selection of hybrids, and hence G. hirsutum genome, against the maintenance of pure G. barbadense genome. The selection may be influenced by the plant uses: the smaller size of hybrids when compared to the barbadense may lead them to be differentiated from these parents to which medicinal properties are attributed; on the other hand, the greater boll production may favor hybrids maintenance with the purpose of producing lamp wicks, or use as an ornamental or swab