Strategies for Minimum Distance in Simulated Evacuation of Transport Airplanes

The present paper describes the preliminary stages of the development of a new, comprehensive model conceived to simulate the evacuation of transport airplanes in certification studies. Two previous steps were devoted to implementing an efficient procedure to define the whole geometry of the cabin, and setting up an algorithm for assigning seats to available exits. Now, to clarify the role of the cabin arrangement in the evacuation process, the paper addresses the influence of several restrictions on the seat-to-exit assignment algorithm, maintaining a purely geometrical approach for consistency. Four situations are considered: first, an assignment method without limitations to search the minimum for the total distance run by all passengers along their escaping paths; second, a protocol that restricts the number of evacuees through each exit according to updated FAR 25 capacity; third, a procedure which tends to the best proportional sharing among exits but obliges to each passenger to egress through the nearest fore or rear exits; and fourth, a scenario which includes both restrictions. The four assignment strategies are applied to turboprops, and narrow body and wide body jets. Seat to exit distance and number of evacuees per exit are the main output variables. The results show the influence of airplane size and the impact of non-symmetries and inappropriate matching between size and longitudinal location of exits.

Vibroacoustic Problems in High Speed Trains

Passengers comfort in terms of acoustic noise levels is a key train design parameter, especially relevant in high speed trains, where the aerodynamic noise is dominant. The aim of the work, described in this paper, is to make progress in the understanding of the flow field around high speed trains in an open field, which is a subject of interest for many researchers with direct industrial applications, but also the critical configuration of the train inside a tunnel is studied in order to evaluate the external loads arising from noise sources of the train. The airborne noise coming from the wheels (wheelrail interaction), which is the dominant source at a certain range of frequencies, is also investigated from the numerical and experimental points of view. The numerical prediction of the noise in the interior of the train is a very complex problem, involving many different parameters: complex geometries and materials, different noise sources, complex interactions among those sources, broad range of frequencies where the phenomenon is important, etc. During recent years a research plan is being developed at IDR/UPM (Instituto de Microgravedad Ignacio Da Riva, Universidad Politécnica de Madrid) involving both numerical simulations, wind tunnel and full-scale tests to address this problem. Comparison of numerical simulations with experimental data is a key factor in this process.

Ontology-driven legal support-system in air transport passenger domain

This paper aims to present a preliminary version of asupport-system in the air transport passenger domain. This system relies upon an underlying on-tological structure representing a normative framework to facilitatethe provision of contextualized relevant legal information.This information includes the pas-senger's rights and itenhances self-litigation and the decision-making process of passengers.Our contribution is based in the attempt of rendering a user-centric-legal informationgroundedon case-scenarios of the most pronounced incidents related to the consumer complaints in the EU.A number ofadvantages with re-spect to the current state-of-the-art services are discussed and a case study illu-strates a possible technological application.

Aerodynamic shape optimization of the nose of a high-speed train subjected to crosswind conditions

When dealing with the design of a high-speed train, a multiobjective shape optimization problem is formulated, as these vehicles are object of many aerodynamic problems which are known to be in conflict. More mobility involves an increase in both the cruise speed and lightness, and these requirements directly influence the stability and the ride comfort of the passengers when the train is subjected to a side wind. Thus, crosswind stability plays a more relevant role among the aerodynamic objectives to be optimized. An extensive research activity is observed on aerodynamic response in crosswind conditions.

Real-time incidents detection in the highways of the future

Due to ever increasing transportation of people and goods, automatic traffic surveillance is becoming a key issue for both providing safety to road users and improving traffic control in an efficient way. In this paper, we propose a new system that, exploiting the capabilities that both computer vision and machine learning offer, is able to detect and track different types of real incidents on a highway. Specifically, it is able to accurately detect not only stopped vehicles, but also drivers and passengers leaving the stopped vehicle, and other pedestrians present in the roadway. Additionally, a theoretical approach for detecting vehicles which may leave the road in an unexpected way is also presented. The system works in real-time and it has been optimized for working outdoor, being thus appropriate for its deployment in a real-world environment like a highway. First experimental results on a dataset created with videos provided by two Spanish highway operators demonstrate the effectiveness of the proposed system and its robustness against noise and low-quality videos.

Sistema supervisor central de eventos en entorno ferroviario

En el campo del ferrocarril es necesaria tecnología avanzada que ayude en la seguridad de los trenes y de los pasajeros, en caso de viajes comerciales. Para ello en los pasos a nivel es necesario tener mecanismos que detallen cualquier incidencia, o cualquier anomalía respecto a las vías, bajadas de vayas, etc. Aquí toma vida esta aplicación llamada SCSE (Sistema Supervisor Central de Eventos en Entorno Ferroviario), que ofrece una cantidad importante de información. Esta aplicación recoge en el momento toda la información de los distintos pasos a nivel; y nos dice dónde está fallando el paso, si hay un error en la subida/bajada de vayas, si el semáforo no ha cambiado de color a tiempo... y lo hace visual en la pantalla. Con esta aplicación se pretende ofrecer una mayor eficacia en seguridad, una mayor rapidez en reparación de incidencias y una organización dentro de la empresa para poder ver sobre que se está trabajando.---ABSTRACT---In the field of rail technology is needed to assist in the safety of trains and passengers in case of commercial travel. To do this on level crossings is necessary to have mechanisms that detail any incident or any matter relating to rails etc. Here comes alive this application called SCSE (Central Events Supervisor System Environment Railway), which provides a significant amount of information. This application collects in the moment all the information of the different level crossings; and it tells us where it is failing level crossing, if there is an error in the up / down, if the light has not changed color in time ... and makes visual on the screen. With this application is intended to provide more effective security, a faster repair incidents and organization inside the company to see on which they are working.

Evaluación teórico experimental de la influencia de espumas de relleno metálicas como elementos de absorción de energía en perfiles tubulares de pequeño espesor. Su aplicación a vehículos para el transporte colectivo de personas

Los accidentes con implicación de autocares en los que se producen vuelcos ponen de manifiesto la especial agresividad de los mismos, como lo confirman las estadísticas. Como medida para mejorar la seguridad de los Vehículos de Grandes Dimensiones para el Transporte de Pasajeros (V.G.D.T.P.) frente a vuelco fue aprobado por las Naciones Unidas el Reglamento Nº 66 de Ginebra. Este reglamento establece los requisitos mínimos que las estructuras de los vehículos de grandes dimensiones deben cumplir con respecto a vuelco. El reglamento 66 ha supuesto un paso adelante muy importante en relación con la seguridad de los autocares, puesto que especifica por primera vez requerimientos estructurales a este tipo de vehículos, y en general ha supuesto una mejora del vehículo . Por otro lado, a consecuencia de la obligatoriedad de instalación de cinturones de seguridad, existe una unión entre pasajeros y vehículo, pero como no se trata de una unión rígida, hay que contemplar el porcentaje de la masa de los ocupantes que influye en la absorción de energía de la estructura. Además la retención de los ocupantes con cinturones de seguridad influye en la energía a absorber por la estructura del vehículo en dos aspectos, por un lado aumenta la masa del vehículo y en el otro se incrementa la altura el centro de gravedad. Esta situación a conducido a elaborar por parte de las Naciones Unidas la revisión 01 del Reglamento 66, en el que se considera que el 50 % de la masa total de los pasajeros posee una unión rígida con la estructura del vehículo, y por lo tanto debe ser tenida en cuenta si el vehículo posee sistemas de retención. En la situación actual, con limitaciones de peso del vehículo y peso por eje, los elementos de confort, seguridad y espacio para maleteros contribuyen a aumentar el peso del vehículo. Esto unido a la dificultad de introducción de cambios radicales en la concepción actual de fabricación de este tipo de vehículos por suponer unas pérdidas importantes para los fabricantes existentes, tanto en su conocimiento del producto como en su metodología de proceso, conlleva la necesidad cada vez más agobiante de analizar y evaluar otras alternativas estructurales que sin suponer grandes revoluciones a los productos actualmente en fabricación los complementen permitiendo adaptarse a los nuevos requerimientos en seguridad. Recientes desarrollos en la relación costo-beneficio de los procesos para la producción de materiales celulares metálicos de baja densidad, tales como las espumas metálicas, los posiciona como una alternativa de especial interés para la aplicación como elementos de absorción de energía para reforzar estructuras. El relleno con espumas metálicas puede ser más eficiente en términos de optimización de peso comparado con el aumento de espesor de los perfiles estructurales, dado que la absorción de energía se produce en una fracción relativamente pequeña de los perfiles, en las denominadas rótulas plásticas. La aplicación de espumas de relleno metálicas en estructuras de vehículos se está empezando a emplear en determinadas zonas de los vehículos de turismo, siendo totalmente novedosa cualquier intento de aplicación en estructuras de autobuses y autocares. Conforme a lo expuesto, y con el objeto de resolver estos problemas, se ha elaborado el presente trabajo de tesis doctoral, cuyos objetivos son: -Desarrollar un modelo matemático, que permita simular el ensayo de vuelco, considerando la influencia de los ocupantes retenidos con cinturones de seguridad para evaluar su influencia en la absorción de energía de la estructura. -Validar el modelo matemático de vuelco de la estructura mediante ensayos de secciones representativas de la estructura del vehículo y mediante el ensayo de un vehículo completo. -Realizar un estudio de las propiedades de las espumas metálicas que permitan incorporarlas como elemento de absorción de energía en el relleno de componentes de la superestructura de autobuses y autocares. -Desarrollar un modelo matemático para evaluar el aporte del relleno de espuma metálica en la absorción de energía ante solicitaciones por flexión estática y dinámica en componentes de la superestructura de autobuses o autocares. -Realizar un programa de ensayos a flexión estáticos y dinámicos para validar el modelo matemático del aporte del relleno de espuma metálica sobre componentes de la superestructura de autobuses y autocares. . -Incorporar al modelo matemático de vuelco de la estructura, los resultados obtenidos sobre componentes con relleno de espuma metálica, para evaluar el aporte en la absorción de energía. -Validar el modelo de vuelco de la estructura del autobús o autocar con relleno de espuma metálica, mediante ensayos de secciones de carrocería. ABSTRACT Accidents involving buses in which rollovers occur reveal the special aggressiveness thereof, as the statistics prove. As a measure to improve the safety of large vehicles for the transport of passengers to rollover, Regulation 66 of Geneva was approved by the United Nations. This regulation establishes the minimum requirements that structures of large vehicles must comply with respect to rollovers. The regulation 66 has been a major step forward in relation to the safety of coaches, since it specifies structural requirements to such vehicles and has been an improvement for the vehicle. In turn, as a result of compulsory installation of safety belts, there is contact between passengers and vehicle, but as it is not a rigid connection we must contemplate the percentage of the mass of the occupants that impacts on the energy absorption of the structure. Thus, the passengers��� restraining modifies the energy to absorb by the vehicle in two different aspects: On the one hand, it increases the vehicle weight and on the other the height of the center of gravity. This circumstance has taken the United Nations to elaborate Revision 01 of Regulation 66, in which it is considered that the 50 percent of passengers��� mass has a rigid joint together with the vehicle structure and, therefore, the passengers��� mass mentioned above should be highly considered if the vehicle has seat belts. In the present situation, in which limitations in vehicle weight and weight in axles are stricter, elements of comfort, safety and space for baggage are contributing to increase the weight of the vehicle. This coupled with the difficulty of introducing radical changes in the current conception of manufacturing such vehicles pose significant losses for existing manufacturers, both in product knowledge and process methodology, entails the overwhelming need to analyze and evaluate other structural alternatives without assuming relevant modifications on the products manufactured currently allowing them to adapt to the new safety requirements. Recent developments in cost-benefit processes for the production of metallic foams of low density, such as metal foams, place them as an alternative of special interest to be used as energy absorbers to strengthen structures. The filling with metal foams can be more efficient in terms of weight optimization compared with increasing thickness of the structural beams, since the energy absorption occurs in a relatively small fraction of the beams, called plastic hinges. The application of metal filling foams in vehicle structures is beginning to be used in certain areas of passenger cars, being an innovative opportunity in structures for application in buses and coaches. According to the mentioned before, and in order to come forward with a solution, this doctoral thesis has been prepared and its objectives are: - Develop a mathematical model to simulate the rollover test, considering the influence of the occupants held with seat belts to assess their influence on energy absorption structure. - Validate the mathematical model of the structure rollover by testing representative sections of the vehicle structure and by testing a complete vehicle. - Conduct a study of the properties of metal foams as possible incorporation of energy absorbing element in the filler component of the superstructure of buses and coaches. - Elaborate a mathematical model to assess the contribution of the metal foam filling in absorbing energy for static and dynamic bending loads on the components of buses or coaches superstructure. - Conduct a static and dynamic bending test program to validate the mathematical model of contribution of metal foam filling on components of the superstructure of buses and coaches bending. - To incorporate into the mathematical model of structure rollover, the results obtained on components filled with metal foam, to evaluate the contribution to the energy absorption. - Validate the rollover model structure of the bus or coach filled with metal foam through tests of bay sections. The objectives in this thesis have been achieved successfully. The contribution calculation model with metal foam filling in the vehicle structure has revealed that the filling with metal foam is more efficient than increasing thickness of the beams, as demonstrated in the experimental validation of bay sections.

La Península Ibérica en el transporte masivo de mercancías entre Europa y África : futuras autopistas del mar

La competitividad del transporte de mercancías depende del estado y funcionamiento de las redes existentes y de sus infraestructuras, no del modo de transporte. En concreto, la rentabilidad o la reducción de los costes de producción del transporte marítimo se vería incrementado con el uso de buques de mayor capacidad y con el desarrollo de plataformas portuarias de distribución o puertos secos, ya que el 90% del comercio entre la Unión Europea y terceros países se realiza a través de sus puertos a un promedio de 3,2 billones de toneladas de mercancías manipuladas cada año y el 40% del tráfico intraeuropeo utiliza el transporte marítimo de corta distancia. A pesar de que los puertos europeos acogen anualmente a más de 400 millones de pasajeros, los grandes desarrollos se han producido en los puertos del norte de Europa (Róterdam, Amberes, Ámsterdam). Los países del Sur de Europa deben buscar nuevas fórmulas para ser más competitivos, ya sea mediante creación de nuevas infraestructuras o mediante refuerzo de las existentes, ofreciendo los costes de los puertos del Norte. El fomento del transporte marítimo y fluvial como alternativa al transporte por carretera, especialmente el transporte marítimo de corta distancia, ha sido impulsado por la Comisión Europea (CE) desde 2003 a través de programas de apoyo comunitario de aplicación directa a las Autopistas del Mar, a modo de ejemplo, cabría citar los programas Marco Polo I y II, los cuales contaron con una dotación presupuestaria total de 855 millones de euros para el período 2003 – 2013; en ese período de tiempo se establecieron objetivos de reducción de congestión vial y mejora del comportamiento medio ambiental del sistema de transporte de mercancías dentro de la comunidad y la potenciación de la intermodalidad. El concepto de Autopista del Mar surge en el Libro Blanco de Transportes de la Comisión Europea “La política europea de transportes de cara al 2010: La hora de la verdad” del 12 de diciembre de 2001, en el marco de una política europea para fomento y desarrollo de sistemas de transportes sostenibles. Las Autopistas del Mar consisten en rutas marítimas de corta distancia entre dos puntos, de menor distancia que por vía terrestre, en las que a través del transporte intermodal mejoran significativamente los tiempos y costes de la cadena logística, contribuyen a la reducción de accidentes, ruidos y emisiones de CO2 a la atmósfera, permite que los conductores pierdan horas de trabajo al volante y evita el deterioro de las infraestructuras terrestres, con el consiguiente ahorro en mantenimiento. La viabilidad de una Autopista del Mar depende tanto de factores de ubicación geográficos, como de características propias del puerto, pasando por los diferentes requerimientos del mercado en cada momento (energéticos, medio ambientales y tecnológicos). Existe un elemento nuevo creado por la Comisión Europea: la red transeuropea de transportes (RTE-T). En el caso de España, con sus dos accesos por los Pirineos (La Junquera e Irún) como únicos pasos terrestres de comunicación con el continente y con importantes limitaciones ferroviarias debido a los tres anchos de vía distintos, le resta competitividad frente al conjunto europeo; por el contrario, España es el país europeo con más kilómetros de costa (con más de 8.000 km) y con un emplazamiento geográfico estratégico, lo que le convierte en una plataforma logística para todo el sur de Europa, por lo que las Autopistas del Mar tendrán un papel importante y casi obligado para el desarrollo de los grandes corredores marítimos que promueve Europa. De hecho, Gijón y Vigo lo han hecho muy bien con sus respectivas líneas definidas como Autopistas del Mar y que conectan con el puerto francés de Nantes-Saint Nazaire, ya que desde ahí los camiones pueden coger rutas hacia el Norte. Paralelamente, la Unión Europea ha iniciado los pasos para el impulso de la primera Autopista del Mar que conectará España con el mercado de Reino Unido, concretamente los Puertos de Bilbao y Tilbury. Además, España e Italia sellaron un acuerdo internacional para desarrollar Autopistas del Mar entre ambos países, comprometiéndose a impulsar una docena de rutas entre puertos del litoral mediterráneo español y el italiano. Actualmente, están en funcionando los trayectos como Barcelona-Génova, Valencia-Civitavecchia y Alicante- Nápoles, notablemente más cortos por mar que por carretera. Bruselas identificó cuatro grandes corredores marítimos que podrían concentrar una alta densidad de tráfico de buques, y en dos de ellos España ya tenía desde un principio un papel crucial. La Comisión diseñó el 14 de abril de 2004, a través del proyecto West-Mos, una red de tráfico marítimo que tiene como vías fundamentales la denominada Autopista del Báltico (que enlaza Europa central y occidental con los países bálticos), la Autopista de Europa suroriental (que une el Adriático con el Jónico y el Mediterráneo más oriental) y también la Autopista de Europa occidental y la Autopista de Europa suroccidental (que enlazan España con Reino Unido y la Francia atlántica y con la Francia mediterránea e Italia, respectivamente). Para poder establecer Autopistas del Mar entre la Península Ibérica y el Norte de Europa primará especialmente la retirada de camiones en la frontera pirenaica, donde el tráfico pesado tiene actualmente una intensidad media diaria de 8.000 unidades, actuando sobre los puntos de mayor congestión, como por ejemplo los Alpes, los Pirineos, el Canal de la Mancha, las carreteras fronterizas de Francia y Euskadi, y proponiendo el traslado de las mercancías en barcos o en trenes. Por su parte, para contar con los subsidios y apoyos europeos las rutas seleccionadas como Autopistas del Mar deben mantener una serie de criterios de calidad relacionados con la frecuencia, coste “plataforma logística a plataforma logística”, simplicidad en procedimientos administrativos y participación de varios países, entre otros. Los estudios consideran inicialmente viables los tramos marítimos superiores a 450 millas, con un volumen de unas 15.000 plataformas al año y que dispongan de eficientes comunicaciones desde el puerto a las redes transeuropeas de autopistas y ferrocarril. Otro objetivo de las Autopistas del Mar es desarrollar las capacidades portuarias de forma que se puedan conectar mejor las regiones periféricas a escala del continente europeo. En lo que a Puertos se refiere, las terminales en los muelles deben contar con una línea de atraque de 250 m., un calado superior a 8 m., una rampa “ro-ro” de doble calzada, grúas portainer, y garantizar operatividad para un mínimo de dos frecuencias de carga semanales. El 28 de marzo de 2011 se publicó el segundo Libro Blanco sobre el futuro del transporte en Europa “Hoja de ruta hacia un espacio único europeo de transporte: por una política de transportes competitiva y sostenible”, donde se definió el marco general de las acciones a emprender en los próximos diez años en el ámbito de las infraestructuras de transporte, la legislación del mercado interior, la reducción de la dependencia del carbono, la tecnología para la gestión del tráfico y los vehículos limpios, así como la estandarización de los distintos mercados. Entre los principales desafíos se encuentran la eliminación de los cuellos de botella y obstáculos diversos de nuestra red europea de transporte, minimizar la dependencia del petróleo, reducir las emisiones de GEI en un 60% para 2050 con respecto a los niveles de 1990 y la inversión en nuevas tecnologías e infraestructuras que reduzcan estas emisiones de transporte en la UE. La conexión entre la UE y el norte de África provoca elevados niveles de congestión en los puntos más críticos del trayecto: frontera hispano-francesa, corredor del Mediterráneo y el paso del estrecho. A esto se le añade el hecho de que el sector del transporte por carretera está sujeto a una creciente competencia de mercado motivada por la eliminación de las barreras europeas, mayores exigencias de los cargadores, mayores restricciones a los conductores y aumento del precio del gasóleo. Por otro lado, el mercado potencial de pasajeros tiene una clara diferenciación en tipos de flujos: los flujos en el período extraordinario de la Operación Paso del Estrecho (OPE), enfocado principalmente a marroquíes que vuelven a su país de vacaciones; y los flujos en el período ordinario, enfocado a la movilidad global de la población. Por tanto, lo que se pretende conseguir con este estudio es analizar la situación actual del tráfico de mercancías y pasajeros con origen o destino la península ibérica y sus causas, así como la investigación de las ventajas de la creación de una conexión marítima (Autopista del Mar) con el Norte de África, basándose en los condicionantes técnicos, administrativos, económicos, políticos, sociales y medio ambientales. The competitiveness of freight transport depends on the condition and operation of existing networks and infrastructure, not the mode of transport. In particular, profitability could be increased or production costs of maritime transport could be reduced by using vessels with greater capacity and developing port distribution platforms or dry ports, seeing as 90% of trade between the European Union and third countries happens through its ports. On average 3,2 billion tonnes of freight are handled annualy and 40% of intra-European traffic uses Short Sea Shipping. In spite of European ports annually hosting more than 400 million passengers, there have been major developments in the northern European ports (Rotterdam, Antwerp, Amsterdam). Southern European countries need to find new ways to be more competitive, either by building new infrastructure or by strengthening existing infrastructure, offering costs northern ports. The use of maritime and river transport as an alternative to road transport, especially Short Sea Shipping, has been driven by the European Commission (EC) from 2003 through community support programs for the Motorways of the Sea. These programs include, for example, the Marco Polo I and II programs, which had a total budget of 855 million euros for the period 2003-2013. During this time objectives were set for reducing road congestion, improving the environmental performance of the freight transport system within the community and enhancing intermodal transport. The “Motorway of the Sea” concept arises in the European Commission’s Transport White Paper "European transport policy for 2010: time to decide" on 12 December 2001, as part of a European policy for the development and promotion of sustainable transport systems. A Motorway of the Sea is defined as a short sea route between two points, covering less distance than by road, which provides a significant improvement in intermodal transport times and to the cost supply chain. It contributes to reducing accidents, noise and CO2 emissions, allows drivers to shorten their driving time and prevents the deterioration of land infrastructure thereby saving on maintenance costs. The viability of a Motorway of the Sea depends as much on geographical location factors as on characteristics of the port, taking into account the different market requirements at all times (energy, environmental and technological). There is a new element created by the European Commission: the trans-European transport network (TEN-T). In the case of Spain, with its two access points in the Pyrenees (La Junquera and Irun) as the only land crossings connected to the mainland and major railway limitations due to the three different gauges, it appears less competitive compared to Europe as a whole. However, Spain is the European country with the most kilometers of coastline (over 8,000 km) and a strategic geographical location, which makes it a logistics platform for the all of Southern Europe. This is why the Motorways of the Sea will have an important role, and an almost necessary one to develop major maritime corridors that Europe supports. In fact, Gijon and Vigo have done very well with their respective sea lanes defined as Motorways of the Sea and which connect with the French port of Nantes-Saint Nazaire, as from there trucks can use nort-heading routes. In parallel, the European Union has taken the first steps to boost the first Motorway of the Sea linking Spain to the UK market, specifically the ports of Bilbao and Tilbury. Furthermore, Spain and Italy sealed an international agreement to develop Motorways of the Sea between both countries, pledging to develop a dozen routes between ports on the Spanish and Italian Mediterranean coasts. Currently, there are sea lanes already in use such as Barcelona-Genova, Valencia-Civitavecchia and Alicante-Naples, these are significantly shorter routes by sea than by road. Brussels identified four major maritime corridors that could hold heavy concentrate shipping traffic, and Spain had a crucial role in two of these from the beginning. On 14 April 2004 the Commission planned through the West-Mos project, a network of maritime traffic which includes the essential sea passages the so-called Baltic Motorway (linking Central and Western Europe with the Baltic countries), the southeast Europe Motorway (linking the Adriatic to the Ionian and eastern Mediterranean Sea), the Western Europe Motorway and southwestern Europe Motorway (that links Spain with Britain and the Atlantic coast of France and with the French Mediterranean coast and Italy, respectively). In order to establish Motorways of the Sea between the Iberian Peninsula and Northern Europe especially, it is necessary to remove trucks from the Pyrenean border, where sees heavy traffic (on average 8000 trucks per day) and addressing the points of greatest congestion, such as the Alps, the Pyrenees, the English Channel, the border roads of France and Euskadi, and proposing the transfer of freight on ships or trains. For its part, in order to receive subsidies and support from the European Commission, the routes selected as Motorways of the Sea should maintain a series of quality criteria related to frequency, costs "from logistics platform to logistics platform," simplicity in administrative procedures and participation of several countries, among others. To begin with, studies consider viable a maritime stretch of at least 450 miles with a volume of about 15,000 platforms per year and that have efficient connections from port to trans-European motorways and rail networks. Another objective of the Motorways of the Sea is to develop port capacity so that they can better connect peripheral regions across the European continent. Referring ports, the terminals at the docks must have a berthing line of 250 m., a draft greater than 8 m, a dual carriageway "ro-ro" ramp, portainer cranes, and ensure operability for a minimum of two loads per week. On 28 March 2011 the second White Paper about the future of transport in Europe "Roadmap to a Single European Transport Area – Towards a competitive and resource efficient transport system" was published. In this Paper the general framework of actions to be undertaken in the next ten years in the field of transport infrastructure was defined, including internal market legislation, reduction of carbon dependency, traffic management technology and clean vehicles, as well as the standardization of different markets. The main challenges are how to eliminate bottlenecks and various obstacles in our European transport network, minimize dependence on oil, reduce GHG emissions by 60% by 2050 compared to 1990 levels and encourage investment in new technologies and infrastructure that reduce EU transport emissions. The connection between the EU and North Africa causes high levels of congestion on the most critical points of the journey: the Spanish-French border, the Mediterranean corridor and Gibraltar Strait. In addition to this, the road transport sector is subject to increased market competition motivated by the elimination of European barriers, greater demands of shippers, greater restrictions on drivers and an increase in the price of diesel. On the other hand, the potential passenger market has a clear differentiation in type of flows: flows in the special period of the Crossing the Straits Operation (CSO), mainly focused on Moroccans who return home on vacation; and flows in the regular session, focused on the global mobile population. Therefore, what I want to achieve with this study is present an analysis of the current situation of freight and passengers to or from the Iberian Peninsula and their causes, as well as present research on the advantages of creating a maritime connection (Motorways of the Sea) with North Africa, based on the technical, administrative, economic, political, social and environmental conditions.

Estudio teórico-experimental para la mejora de la resistencia estructural de autocares basado en el diseño de uniones y asientos

La presente tesis analiza la mejora de la resistencia estructural ante vuelco de autocares enfocando dos vías de actuación: análisis y propuestas de requisitos reglamentarios a nivel europeo y la generación de herramientas que ayuden al diseño y a la verificación de estos requisitos. Los requisitos reglamentarios de resistencia estructural a vuelco contemplan la superestructura de los vehículos pero no para los asientos y sistemas de retención. La influencia de los pasajeros retenidos es superior a la incluida en reglamentación (Reg. 66.01) debiendo considerarse unida al vehículo un porcentaje de la masa de los pasajeros del 91% para cinturón de tres puntos y del 52% para cinturón subabdominal frente al 50% reglamentario para todos los casos. Se ha determinado la cinemática y dinámica del vuelco normativo en sus diferentes fases, formulando las energías en las fases iniciales (hasta el impacto contra el suelo) y determinando la fase final de deformación a través del análisis secuencial de ensayos de módulos reales. Se han determinado los esfuerzos para los asientos que se dividen en dos fases diferenciadas temporalmente: una primera debida a la deformación estructural y una segunda debida al esfuerzo del pasajero retenido que se produce en sentido opuesto (con una deceleración del pasajero en torno a 3.3 g). Se ha caracterizado a través de ensayos cuasi.estáticos el comportamiento de perfiles a flexión y de las uniones estructurales de las principales zonas del vehículo (piso, ventana y techo) verificándose la validez del comportamiento plástico teórico Kecman.García para perfiles de hasta 4 mm de espesor y caracterizando la resistencia y rigidez en la zona elástica de las uniones en función del tipo de refuerzo, materiales y perfiles (análisis de más de 180 probetas). Se ha definido un método de ensayo cuasi.estático para asientos ante esfuerzos de vuelco, ensayándose 19 butacas y determinándose que son resistentes (salvo las uniones a vehículo con pinzas), que son capaces de absorber hasta más de un 17% de la energía absorbida, aunque algunos necesitan optimización para llegar a contribuir en el mecanismo de deformación estructural. Se han generado modelos simplificados para introducir en los modelos barra.rótula plástica: un modelo combinado unión+rótula plástica (que incluye la zona de rigidez determinada en función del tipo de unión) para la superestructura y un modelo simplificado de muelles no.lineales para los asientos. Igualmente se ha generado la metodología de diseño a través de ensayos virtuales con modelos de detalle de elementos finitos tanto de las uniones como de los asientos. Se ha propuesto una metodología de diseño basada en obtener el “mecanismo óptimo de deformación estructural” (elevando la zona de deformación lateral a nivel de ventana y en pilar o en costilla en techo). Para ello se abren dos vías: diseño de la superestructura (selección de perfiles y generación de uniones resistentes) o combinación con asientos (que en lugar de solo resistir las cargas pueden llegar a modificar el mecanismo de deformación). Se ha propuesto una metodología de verificación alternativa al vuelco de vehículo completo que contempla el cálculo cuasi.estático con modelos simplificados barra.rótula plástica más el ensayo de una sección representativa con asientos y utillajes antropomórficos retenidos que permite validar el diseño de las uniones, determinar el porcentaje de energía que debe absorberse por deformación estructural (factor C) y verificar el propio asiento como sistema de retención. ABSTRACT This research analyzes the improvement of the structural strength of buses and coaches under rollover from two perspectives: regulatory requirements at European level and generation of tools that will help to the design and to the verification of requirements. European Regulations about rollover structural strength includes requirements for the superstructure of the vehicles but not about seats, anchorages and restraint systems. The influence of the retained passengers is higher than the one included currently in the Regulations (Reg. 66.01), being needed to consider a 91% of the passenger mass as rigidly joint to the vehicle (for 3 points’ belt, a 52% for 2 points’ belt) instead of the 50% included in the Regulation. Kinematic and dynamic of the normative rollover has been determined from testing of different sections, formulating the energies of the first phases (up to the first impact with the ground) and determining the last deformation phase through sequential analysis of movements and deformations. The efforts due to rollover over the seats have been established, being divided in two different temporal phases: a first one due to the structural deformation of the vehicle and a second one due to the effort of the restrained passenger being this second one in opposite sense (with a passenger deceleration around 3.3 g). From quasi.static testing, the behavior of the structural tubes under flexural loads, including the principal joints in the vehicle (floor, window and roof), the validity of the theoretical plastic behavior according Kecman.García theories have been verified up to 4 mm of thickness. Strength of the joints as well as the stiffness of the elastic zone has been determined in function of main parameters: type of reinforcement, materials and section of the tubes (more than 180 test specimens). It has been defined a quasi.static testing methodology to characterize the seats and restrain system behavior under rollover, testing 19 double seats and concluding that they are resistant (excepting clamping joints), that they can absorb more than a 17 of the absorbed energy, and that some of them need optimization to contribute in the structural deformation mechanism. It has been generated simplified MEF models, to analyze in a beam.plastic hinge model: a combined model joint+plastic hinge (including the stiffness depending on the type of joint) for the superstructure and a simplified model with non.lineal springs to represent the seats. It has been detailed methodologies for detailed design of joints and seats from virtual testing (MEF models). A design methodology based in the “optimized structural deformation mechanism” (increasing the height of deformation of the lateral up to window level) is proposed. Two possibilities are analyzed: design of the superstructure based on the selection of profiles and design of strength joints (were seats only resist the efforts and contribute in the energy absorption) or combination structure.seats, were seats contributes in the deformation mechanism. An alternative methodology to the rollover of a vehicle that includes the quasi.static calculation with simplified models “beam.joint+plastic hinge” plus the testing of a representative section of the vehicle including seats and anthropomorphic ballast restrained by the safety belts is presented. The test of the section allows validate the design of the joints, determine the percentage of energy to be absorbed by structural deformation (factor C) and verify the seat as a retention system.

Passenger Exposure to Magnetic Fields due to the Batteries of an Electric Vehicle

In electric vehicles, passengers sit very close to an electric system of significant power. The high currents achieved in these vehicles mean that the passengers could be exposed to significant magnetic fields. One of the electric devices present in the power train are the batteries. In this paper, a methodology to evaluate the magnetic field created by these batteries is presented. First, the magnetic field generated by a single battery is analyzed using finite elements simulations. Results are compared to laboratory measurements, taken from a real battery, in order to validate the model. After this, the magnetic field created by a complete battery pack is estimated and results are discussed.

Desenvolvimento de algoritmo de controle de tração para regeneração de energia metroviária - ACTREM: melhoria da eficiência energética de sistemas de tração metroviária.

Esta tese propõe um modelo de regeneração de energia metroviária, baseado no controle de paradas e partidas do trem ao longo de sua viagem, com o aproveitamento da energia proveniente da frenagem regenerativa no sistema de tração. O objetivo é otimizar o consumo de energia, promover maior eficiência, na perspectiva de uma gestão sustentável. Aplicando o Algoritmo Genético (GA) para obter a melhor configuração de tráfego dos trens, a pesquisa desenvolve e testa o Algoritmo de Controle de Tração para Regeneração de Energia Metroviária (ACTREM), usando a Linguagem de programação C++. Para analisar o desempenho do algoritmo de controle ACTREM no aumento da eficiência energética, foram realizadas quinze simulações da aplicação do ACTREM na linha 4 - Amarela do metrô da cidade de São Paulo. Essas simulações demonstraram a eficiência do ACTREM para gerar, automaticamente, os diagramas horários otimizados para uma economia de energia nos sistemas metroviários, levando em consideração as restrições operacionais do sistema, como capacidade máxima de cada trem, tempo total de espera, tempo total de viagem e intervalo entre trens. Os resultados mostram que o algoritmo proposto pode economizar 9,5% da energia e não provocar impactos relevantes na capacidade de transporte de passageiros do sistema. Ainda sugerem possíveis continuidades de estudos.

Letter from Benjamin Colman to Edward Wigglesworth about John Leverett, 1728 March 4

Benjamin Colman wrote this letter to Edward Wigglesworth on March 4, 1728; it was sent from Colman, in Boston, to Wigglesworth, in Cambridge. The letter concerns their mutual friend, John Leverett, who had died several years before. It appears that Wigglesworth was charged with writing an epitaph for Leverett and had solicited input from Colman. Colman writes of his great admiration for Leverett, praising his "virtue & piety, wisdom & gravity [...] majesty & authority [...] eye & voice, goodness & courtesie."

Airport Security: Passenger's Perception and Design Issues

The main goal of this thesis is to report patterns of perceived safety in the context of airport infrastructure, taking the airport of Bologna as reference. Many personal and environmental attributes are investigated to paint the profile of the sensitive passenger and to understand why precise factors of the transit environment are so impactful on the individual. The main analyses are based on a 2014-2015 passengers��� survey, involving almost six thousand of incoming and outgoing passengers. Other reports are used to implement and support the resource. The analysis is carried out by using a combination of Chi-square tests and binary logistic regressions. Findings shows that passengers result to be particularly affected by the perception of airport’s environment (e.g., state and maintenance of facilities, clarity and efficacy of information system, functionality of elevators and escalators), but also by the way how the passenger reaches the airport and the quality of security checks. In relation to such results, several suggestions are provided for the improvement of passenger satisfaction with safety. The attention is then focused on security checkpoints and related operations, described on a theoretical and technical ground. We present an example of how to realize a proper model of the security checks area of Bologna’s airport, with the aim to assess present performances of the system and consequences of potential variations. After a brief introduction to Arena, a widespread simulation software, the existing model is described, pointing out flaws and limitations. Such model is finally updated and changed in order to make it more reliable and more representative of the reality. Different scenarios are tested and results are compared using graphs and tables.

Urban Vehicle Design Competition

The "Urban Car One Thousand" is designed to hold two passengers 35 hp wankel type rotation combustion engine Competition intended to provide a forum for students to express a technological solution to the urban transportation crisis. Students, left ot right, Mitch Walker, Tom Newhouse, Mark Bonnette

Symbol signs 2. The development of passenger/pedestrian oriented symbols for use in transportation-related facilities. Final report.

Transportation Department, Research and Special Programs Administration, Washington, D.C.