An assessment of creep deformation and fracture behavior of 2.25Cr-1Mo similar and dissimilar weld joints

The evaluation of the creep deformation and fracture behavior of a 2.25Cr-1Mo steel base metal, a 2.25Cr-1Mo/2.25Cr-1Mo similar weld joint, and a 2.25Cr-1Mo/Alloy 800 dissimilar weld joint at 823 K over a stress range of 90 to WO MPa has been carried out. The specimens for creep testing were taken from single-V weld pads fabricated by a shielded metal arc-welding process using 2.25Cr-1Mo steel (for similar-joint) and INCONEL 182 (for dissimilar-joint) electrodes. The weld pads were subsequently given a postweld hear treatment (PWHT) of 973 K for I hour. The microstructure and microhardness of the weld joints were evaluated in the as-welded, postweld heat-treated, and creep-tested conditions. The heat-affected zone (HAZ) of similar weld joint consisted of bainite in the coarse-prior-austenitic-grain (CPAG) region near the fusion line, followed by bainite in the fine-prior-austenitic-grain (FPAG) and intercritical regions merging with the unaffected base metal. In addition to the HAZ structures in the 2.25Cr-1Mo steel, the dissimilar weld joint displayed a definite INCONEL/2.25Cr-1Mo weld interface structure present either as a sharp line or as a diffuse region. A hardness trough was observed in the intercritical region of the HAZ in both weld joints, while a maxima in hardness was seen at the weld interface of the dissimilar weld joint. Both weld joints exhibited significantly lower rupture lives compared to the 2.25Cr-1Mo base metal. The dissimilar weld joint exhibited poor rupture life compared to the similar weld joint, at applied stresses lower than 130 MPa. In both weld joints, the strain distribution across the specimen gage length during creep testing varied significantly. During creep testing, localization of deformation occurred in the intercritical HAZ. In the similar weld joint, at all stress levels investigated, and in the dissimilar weld joint, at stresses greater than or equal to 150 MPa, the creep failure occulted in the intercritical HAZ. The fracture occurred by transgranular mode with a large number of dimples. At stresses below 150 MPa, the failure in the dissimilar weld joint occurred in the CPAG HAZ near to the weld interface. The failure occurred by extensive intergranular creep cavity formation.

An assessment of creep deformation and fracture behavior of 2.25Cr-1Mo

The evaluation of the creep deformation and fracture behavior of a 2.25Cr-1Mo steel base metal, a 2.25Cr-1Mo/2.25Cr-1Mo similar weld joint, and a 2.25Cr-1Mo/Alloy 800 dissimilar weld joint at 823 K over a stress range of 90 to WO MPa has been carried out. The specimens for creep testing were taken from single-V weld pads fabricated by a shielded metal arc-welding process using 2.25Cr-1Mo steel (for similar-joint) and INCONEL 182 (for dissimilar-joint) electrodes. The weld pads were subsequently given a postweld hear treatment (PWHT) of 973 K for I hour. The microstructure and microhardness of the weld joints were evaluated in the as-welded, postweld heat-treated, and creep-tested conditions. The heat-affected zone (HAZ) of similar weld joint consisted of bainite in the coarse-prior-austenitic-grain (CPAG) region near the fusion line, followed by bainite in the fine-prior-austenitic-grain (FPAG) and intercritical regions merging with the unaffected base metal. In addition to the HAZ structures in the 2.25Cr-1Mo steel, the dissimilar weld joint displayed a definite INCONEL/2.25Cr-1Mo weld interface structure present either as a sharp line or as a diffuse region. A hardness trough was observed in the intercritical region of the HAZ in both weld joints, while a maxima in hardness was seen at the weld interface of the dissimilar weld joint. Both weld joints exhibited significantly lower rupture lives compared to the 2.25Cr-1Mo base metal. The dissimilar weld joint exhibited poor rupture life compared to the similar weld joint, at applied stresses lower than 130 MPa. In both weld joints, the strain distribution across the specimen gage length during creep testing varied significantly. During creep testing, localization of deformation occurred in the intercritical HAZ. In the similar weld joint, at all stress levels investigated, and in the dissimilar weld joint, at stresses greater than or equal to 150 MPa, the creep failure occulted in the intercritical HAZ. The fracture occurred by transgranular mode with a large number of dimples. At stresses below 150 MPa, the failure in the dissimilar weld joint occurred in the CPAG HAZ near to the weld interface. The failure occurred by extensive intergranular creep cavity formation.

On breaks of the Indian monsoon

For over a century, the term break has been used for spells in which the rainfall over the Indian monsoon zone is interrupted. The phenomenon of 'break monsoon' is of great interest because long intense breaks are often associated with poor monsoon seasons. Such breaks have distinct circulation characteristics (heat trough type circulation) and have a large impact on rainfed agriculture. Although interruption of the monsoon rainfall is considered to be the most important feature of the break monsoon, traditionally breaks have been identified on the basis of the surface pressure and wind patterns over the Indian region. We have defined breaks (and active spells) on the basis of rainfall over the monsoon zone. The rainfall criteria are chosen so as to ensure a large overlap with the traditional breaks documented by Ramamurthy (1969) and De et al (1998). We have identified these rainbreaks for 1901-89. We have also identified active spells on the basis of rainfall over the Indian monsoon zone. We have shown that the all-India summer monsoon rainfall is significantly negatively correlated with the number of rainbreak days (correlation coefficient -0.56) and significantly positively correlated with the number of active days (correlation coefficient 0.47). Thus the interannual variation of the all-India summer monsoon rainfall is shown to be related to the number of days of rainbreaks and active spells identified here. There have been several studies of breaks (and also active spells in several cases) identified on the basis of different criteria over regions differing in spatial scales (e.g., Webster et al 1998; Krishnan et al 2000; Goswami and Mohan 2000; and Annamalai and Slingo 2001). We find that there is considerable overlap between the rainbreaks we have identified and breaks based on the traditional definition. There is some overlap with the breaks identified by Krishnan et al (2000) but little overlap with breaks identified by Webster et al (1998). Further, there are three or four active-break cycles in a season according to Webster et al (1998) which implies a time scale of about 40 days for which Goswami and Mohan (2000), and Annamalai and Slingo'(2001) have studied breaks and active minus break fluctuations. On the other hand, neither the traditional breaks (Ramamurthy 1969; and De et al 1998) nor the rainbreaks occur every year. This suggests that the 'breaks' in these studies axe weak spells of the intraseasonal variation of the monsoon, which occur every year. We have derived the OLR and circulation patterns associated with rainbreaks and active spells and compared them with the patterns associated with breaks/active minus break spells from these studies. Inspite of differences in the patterns over the Indian region, there is one feature which is seen in the OLR anomaly patterns of breaks identified on the basis of different criteria as well as the rainbreaks identified in this paper viz., a quadrapole over the Asia-west Pacific region arising from anomalies opposite (same) in sign to those over the Indian region occurring over the equatorial Indian Ocean and northern tropical (equatorial) parts of the west Pacific. Thus it appears that this quadrapole is a basic feature of weak spells of the intraseasonal,variation over the Asia-west Pacific region. Since the rainbreaks are intense weak spells, this basic feature is also seen in the composite patterns of these breaks. We find that rainbreaks (active spells) are also associated with negative (positive) anomalies over a part of the cast Pacific suggesting that the convection over the Indian region is linked to that over the east Pacific not only on the interannual scale (as evinced by the link between the Indian summer monsoon rainfall and ENSO) but on the intraseasonal scale as well.

Evidence for a thermally reversing window in bulk Ge–Te–Si glasses revealed by alternating differential scanning calorimetry

Experiments on Ge15Te85− x Si x glasses (2 ≤ x ≤ 12) using alternating differential scanning calorimetry (ADSC) indicate that these glasses exhibit one glass transition and two crystallization reactions upon heating. The glass transition temperature has been found to increase almost linearly with silicon content, in the entire composition tie-line. The first crystallization temperature (T c1) exhibits an increase with silicon content for x < 5; T c1 remains almost a constant in the composition range 5 < x ≤ 10 and it increases comparatively more sharply with silicon content thereafter. The specific heat change (ΔC p) is found to decrease with an increase in silicon content, exhibiting a minimum at x = 5 (average coordination number, r = 2.4); a continuous increase is seen in ΔC p with silicon concentration above x = 5. The effects seen in the variation with composition of T c1 and ΔC p at x = 5, are the specific signatures of the mean-field stiffness threshold at r = 2.4. Furthermore, a broad trough is seen in the enthalpy change (ΔH NR), which is indicative of a thermally reversing window in Ge15Te85− x Si x glasses in the composition range 2 ≤ x ≤ 6 (2.34 ≤ r ≤ 2.42).

In Situ Electrochemical Polymerization at Air-Water Interface: Surface-Pressure-Induced, Graphene-Oxide-Assisted Preferential Orientation of Polyaniline

In situ electrochemical polymerization of aniline in a Langmuir trough under applied surface pressure assists in the preferential orientation of polyaniline (PANI) in planar polaronic structure. Exfoliated graphene oxide (EGO) spread on water surface is used to bring anilinium cations present in the subphase to air-water interface through electrostatic interactions. Subsequent electrochemical polymerization of aniline under applied surface pressure in the Schaefer mode results in EGO/PANT composite with PANT in planar polaronic form. The orientation of PANI is confirmed by electrochemical and Raman spectroscopic studies. This technique opens up possibilities of 2-D polymerization at the air-water interface. Electrochemical sensing of hydrogen peroxide is used to differentiate the activity of planar and coiled forms of PANI toward electrocatalytic reactions.

Self-Adapting Peripherally Heterofunctionalized Hyperbranched Polymers: Formation of Janus and Tripodal Structures

A peripherally clickable hyperbranched polyester carrying numerous propargyl terminal groups was prepared by a simple melt transesterification polycondensation of a suitably designed AB(2) monomer; this clickable hyperscaffold was then transformed into a variety of different derivatives by using the Cu-catalyzed azide-yne click reaction. Functionalization of the periphery with equimolar quantities of mutually immiscible segments, such as hydrocarbon, fluorocarbon, and PEG, yielded frustrated molecular systems that readapt and form structures wherein the immiscible segments appear to self-segregate to generate either Janus structures (when two immiscible segments are present) or tripodal structures (when three immiscible segments are present). Evidence for such self-segregation was obtained from a variety of studies, such as differential scanning calorimetry, Langmuir isotherms, AFM imaging, and small-angle X-ray scattering measurements. Crystallization of one or more of the peripheral segments reinforced this self-segregation; the weight-fraction-normalized enthalpies of melting associated with the different domains revealed a competition between the segments to optimize their crystalline organization. When one or more of the segments are amorphous, the remaining segments crystallize more effectively and consequently exhibit a higher melting enthalpy. AFM images of monolayers, transferred from the Langmuir trough, revealed that the thickness matches the expected values; furthermore, contact angle measurements clearly demonstrated that the monolayer films are fairly hydrophobic, and in the case of the tripodal hybramers, the presence of domains of hydrocarbon and fluorocarbon appears to impart nanoscale chemical heterogeneity that is reflected in the strong hysteresis in the advancing and receding contact angles.

A Suzaku view of IGR J16393-4643

The pulsar IGR J16393-4643 belongs to a class of highly absorbed supergiant high-mass X-ray binaries (HMXBs), characterized by a very high column density of absorbing matter. We present the results of simultaneous broad-band pulsation and spectrum analysis from a 44-ks Suzaku observation of the source. The orbital intensity profile created with the Swift Burst Alert Telescope (Swift-BAT) light curve shows an indication of IGR J16393-4643 being an eclipsing system with a short eclipse semi-angle theta(E) similar to 17 degrees. For a supergiant companion star with a 20-R-circle dot radius, this implies an inclination of the orbital plane in the range 39 degrees-57 degrees, whereas for a main-sequence B star as the companion with a 10-R-circle dot radius, the inclination of the orbital plane is in the range 60 degrees-77 degrees. Pulse profiles created for different energy bands have complex morphology, which shows some energy dependence and increases in pulse fraction with energy. We have also investigated broad-band spectral characteristics, phase-averaged spectra and resolving the pulse phase into peak and trough phases. The phase-averaged spectrum has a very high N-H(similar to 3 x 10(23) cm(-2)) and is described by a power law (Gamma similar to 0.9) with a high-energy cut-off above 20 keV. We find a change in the spectral index in the peak and trough phases, implying an underlying change in the source spectrum.

La causalidad del Motor inmóvil según Aristóteles

Riassunto: Contro l’interpretazione tradizionale, l’articolo sostiene che il Motore immobile per Aristotele non è causa finale del movimento del cielo, ma ne è piuttosto la causa efficiente, come risulta da Metaph. XII 6. Il Motore immobile è causa finale solo nel senso che egli è fine della sua stessa atitività, come è provato dal fatto che questa è piacere (Metaph. XII 7). L’interpretazione tradizionale, secondo la quale il cielo si muove per amore del Motore immobile, cercando di imitare la sua immobilità per mezzo del moto circolare, deriva dal tentativo di conciliare il pensiero di Aristotele con la concezione platonica dell’imitazione della realtà intelligibile da parte della realtà sensibile. Il motore immobile è fine dell’uomo solo nel senso che è oggetto della conoscenza in cui consiste la felicità umana (Eth. Eud. VIII 3).

Modelización de una prueba de afecto hacia la matemática con la teoría de respuesta al ítem

Resumen: Se aplicó el Modelo de Crédito Parcial (MCP) de la Teoría de Respuesta al Ítem (TRI) al análisis de ítems de una escala que mide Afecto hacia la Matemática. Esta variable describe el interés de los estudiantes de Psicología por involucrarse en actividades vinculadas a la matemática y los sentimientos asociados al uso de sus conceptos. La prueba consta de 8 ítems con formato de respuesta Likert de 6 opciones. Participaron 1875 estudiantes de Psicología de la Universidad de Buenos Aires (Argentina) de los cuales un 82% fueron mujeres. El análisis de la consistencia interna brindó un índice altamente satisfactorio (Alfa = .91). Se verificó la condición de unidimensionalidad requerida por el modelo mediante un análisis factorial exploratorio. Todos los análisis basados sobre la TRI se realizaron con el programa Winsteps. La estimación de los parámetros del modelo se efectuó por Máxima Verosimilitud Conjunta. El ajuste del MCP fue satisfactorio para todos los ítems. La Función de Información del Test fue elevada en un rango amplio de niveles del rasgo latente. Un ítem presentó una inversión en dos parámetros de umbral. Como consecuencia, 1 de las 6 categorías del ítem no fue máximamente probable en ningún intervalo de la escala del rasgo latente. Se analizan las implicancias de este hallazgo en la evaluación de la calidad psicométrica del ítem. Los resultados de este estudio permitieron profundizar el análisis del constructo y aportaron evidencias de validez basadas en las estructura interna de la escala

La teología de Nicolás de Cusa : un desafío para la elaboración de una teología natural

Resumen: El cardenal Nicolás de Cusa se propuso resolver el impasse que en el campo teológico implica la descalificación que desde el nominalismo se hizo conocimiento metafísico. Fue su particular interpretación de la naturaleza de Dios y su modo de conocerla, la que le permitió fundar una nueva teología con la que pretendía superar las limitaciones de un saber que en su opinión sólo era apto para conocer el orden finito. Para ello propone sustituir la vía de conocimiento racional, por otra de carácter puramente intuitivo, cuyo rasgo esencial es el saber del no saber, esto es, la vía de la “docta ignorancia”. Con lo cual el hombre está en condiciones de alcanzar un tipo de saber de orden místico sólo parangonable con el que se puede alcanzar en la bienaventuranza eterna. Es propósito del presente estudio determinar si, sobre las bases presentadas por el Cusano es posible erigir el saber que conviene a una teología natural, e incluso al de una teología mística.

El valor de marca: perspectivas de análisis y criterios de estimación

[ES] A lo largo de la última década, se ha originado un importante debate acerca de lo que debe entenderse por valor de marca. En la delimitación de este concepto se han utilizado varias perspectivas de análisis y criterios de estimación muy diferentes, de ahí que aún exista sobre este tema una excesiva ambigüedad. En este trabajo se presenta un marco teórico donde se contemplan distintas perspectivas de estudio y varios criterios de estimación del valor de marca. A partir de este marco, se analizan empíricamente siete criterios de estimación de acuerdo con la información recogida de una muestra de usuarios sobre seis marcas de zapatillas de deporte. Con ello se pretende contribuir a un mejor conocimiento del concepto de valor de marca.