Time-resolved particle image velocimetry within the nozzle of a drop-on-demand printhead

Time-resolved particle image velocimetry (PIV) has been performed inside the nozzle of a commercially available inkjet print-head to obtain the time-dependent velocity waveform. A printhead with a single transparent nozzle 80 μm in orifice diameter was used to eject single droplets at a speed of 5 m/s. An optical microscope was used with an ultra-high-speed camera to capture the motion of particles suspended in a transparent liquid at the center of the nozzle and above the fluid meniscus at a rate of half a million frames per second. Time-resolved velocity fields were obtained from a fluid layer approximately 200 μm thick within the nozzle for a complete jetting cycle. A Lagrangian finite-element numerical model with experimental measurements as inputs was used to predict the meniscus movement. The model predictions showed good agreement with the experimental results. This work provides the first experimental verification of physical models and numerical simulations of flows within a drop-on-demand nozzle. © 2012 Society for Imaging Science and Technology.

Drop speeds from drop-on-demand ink-jet print heads

Measured drop speeds from a range of industrial drop-on-demand (DoD) ink-jet print head designs scale with the predictions of very simple physical models and results of numerical simulations. The main drop/jet speeds at a specified stand-off depend on fluid properties, nozzle exit diameter, and print head drive amplitude for fixed waveform timescales. Drop speeds from the Xaar, Spectra Dimatix, and MicroFab DoD print heads tested with (i) Newtonian, (ii) weakly elastic, and (iii) highly shear-thinning fluids all show a characteristic linear rise with drive voltage (setting) above an apparent threshold drive voltage. Jetting, simple modeling approaches, and numerical simulations of Newtonian fluids over the typical DoD printing range of surface tensions and viscosities were studied to determine how this threshold drive value and the slope of the characteristic linear rise depend on these fluid properties and nozzle exit area. The final speed is inversely proportional to the nozzle exit area, as expected from volume conservation. These results should assist specialist users in the development and optimization of DoD applications and print head design. For a given density, the drive threshold is determined primarily by viscosity, and the constant of proportionality k linking speed with drive above a drive threshold becomes independent of viscosity and surface tension for more viscous DoD fluid jetting. © 2013 Society for Imaging Science and Technology.

Jetting of complex fluids

Recent results from a number of UK academic inkjet research studies advance the understanding of complex fluid jetting behavior and may be of interest to the wider digital fabrication community for the enhancement of inkjet printing applications. © 2013 Society for Imaging Science and Technology.

Inkjet printing of weakly elastic polymer solutions

Fluid assessment methods, requiring small volumes and avoiding the need for jetting, are particularly useful in the design of functional fluids for inkjet printing applications. With the increasing use of complex (rather than Newtonian) fluids for manufacturing, single frequency fluid characterisation cannot reliably predict good jetting behaviour, owing to the range of shearing and extensional flow rates involved. However, the scope of inkjet fluid assessments (beyond achievement of a nominal viscosity within the print head design specification) is usually focused on the final application rather than the jetting processes. The experimental demonstration of the clear insufficiency of such approaches shows that fluid jetting can readily discriminate between fluids assessed as having similar LVE characterisation (within a factor of 2) for typical commercial rheometer measurements at shearing rates reaching 104rads-1.Jetting behaviour of weakly elastic dilute linear polystyrene solutions, for molecular weights of 110-488. kDa, recorded using high speed video was compared with recent results from numerical modelling and capillary thinning studies of the same solutions.The jetting images show behaviour ranging from near-Newtonian to "beads-on-a-string". The inkjet printing behaviour does not correlate simply with the measured extensional relaxation times or Zimm times, but may be consistent with non-linear extensibility L and the production of fully extended polymer molecules in the thinning jet ligament.Fluid test methods allowing a more complete characterisation of NLVE parameters are needed to assess inkjet printing feasibility prior to directly jetting complex fluids. At the present time, directly jetting such fluids may prove to be the only alternative. © 2014 The Authors.

Articulating current service development practices: a qualitative analysis of eleven mental health projects.

BACKGROUND: The utilisation of good design practices in the development of complex health services is essential to improving quality. Healthcare organisations, however, are often seriously out of step with modern design thinking and practice. As a starting point to encourage the uptake of good design practices, it is important to understand the context of their intended use. This study aims to do that by articulating current health service development practices. METHODS: Eleven service development projects carried out in a large mental health service were investigated through in-depth interviews with six operation managers. The critical decision method in conjunction with diagrammatic elicitation was used to capture descriptions of these projects. Stage-gate design models were then formed to visually articulate, classify and characterise different service development practices. RESULTS: Projects were grouped into three categories according to design process patterns: new service introduction and service integration; service improvement; service closure. Three common design stages: problem exploration, idea generation and solution evaluation - were then compared across the design process patterns. Consistent across projects were a top-down, policy-driven approach to exploration, underexploited idea generation and implementation-based evaluation. CONCLUSIONS: This study provides insight into where and how good design practices can contribute to the improvement of current service development practices. Specifically, the following suggestions for future service development practices are made: genuine user needs analysis for exploration; divergent thinking and innovative culture for idea generation; and fail-safe evaluation prior to implementation. Better training for managers through partnership working with design experts and researchers could be beneficial.

Effects of longer heavy vehicles on traffic congestion

Two-lane, "microscopic" (vehicle-by-vehicle) simulations of motorway traffic are developed using existing models and validated using measured data from the M25 motorway. An energy consumption model is also built in, which takes the logged trajectories of simulated vehicles as drive-cycles. The simulations are used to investigate the effects on motorway congestion and fuel consumption if "longer and/or heavier vehicles" (LHVs) were to be permitted in the UK. Baseline scenarios are simulated with traffic composed of cars, light goods vehicles and standard heavy goods vehicles (HGVs). A proportion of conventional articulated HGVs is then replaced by a smaller number of LHVs carrying the same total payload mass and volume. Four LHV configurations are investigated: an 18.75 m, 46 t longer semi-trailer (LST); 25.25 m, 50 t and 60 t B-doubles and a 34 m, 82 t A-double. Metrics for congestion, freight fleet energy consumption and car energy consumption are defined for comparing the scenarios. Finally, variation of take-up level and LHV engine power for the LST and A-double are investigated. It is concluded that: (a) LHVs should reduce congestion particularly in dense traffic, however, a low mean proportion of freight traffic on UK roads and low take-up levels will limit this effect to be almost negligible; (b) LHVs can significantly improve the energy efficiency of freight fleets, giving up to a 23% reduction in fleet energy consumption at high take-up levels; (c) the small reduction in congestion caused by LHVs could improve the fuel consumption of other road users by up to 3% in dense traffic, however in free-flowing traffic an opposite effect occurs due to higher vehicle speeds and aerodynamic losses; and (d) underpowered LHVs have potential to generate severe congestion, however current manufacturers' recommendations appear suitable. © 2013 IMechE.

Influence of the cavity on the low-temperature photoluminescence of SiGe/Si multiquantum wells grown on a silicon-on-insulator substrate

The influences of the cavity on the low-temperature photoluminescence of Si0.59Ge0.41/Si multiquantum wells grown on silicon-on-insulator substrates are discussed. The positions of the modulated photoluminescence (PL) peaks not only relate to the nature of SiGe/Si multiquantum wells, but also relate to the characteristic of the cavity. With increasing temperature, a redshift of the modulated PL peak originating from the thermo-optical effect of the cavity is observed.

镇海棘螈和大凉疣螈年龄结构研究

通过趾骨切片可以准确鉴定年龄，了解一个物种的最长寿命，也为我们研究确定一个物种的生长特点、性成熟期,以及一个地区一个物种的年龄结构、种群生态(Marnell，1998)和群落生态提供重要信息(Morrison，et a1.，2004)。 本论文使用骨骼鉴龄法对中国浙江省宁波市北仑瑞岩寺林场的镇海棘螈（Echinotriton chinhaiensis）雌性繁群进行了年龄结构研究。结果显示：第一次参加繁殖的年龄为3龄；繁群中数量占优势的是5龄、6龄。而在6龄以后参加繁殖的雌性个体数便开始随着年龄的增大而逐渐减少。参加繁殖的雌性年龄最大个体为8龄。平均年龄为5.13龄。同时对其年龄和头体长、体全长的相关性检验,发现其年龄与头体长和体全长不相关,镇海棘螈雌性的生长方式表现为性成熟后能量主要用于繁殖。 另外,对李子坪大凉疣螈(Tylototriton taliangensis) 雄性繁群进行了年龄结构研究。结果显示：大凉疣螈雄性第一次参加繁殖的年龄为4龄；繁群中数量占优势的是5龄、6龄、7龄。而在7龄以后参加繁殖的雄性个体数便开始随着年龄的增大而逐渐减少。参加繁殖的雄性中年龄最大的个体为10龄。平均年龄为6.7龄。对其年龄和头体长、体全长的相关性检验,发现其年龄与头体长和体全长不相关,大凉疣螈雄性生长特点也表现为性成熟后生长缓慢的特点。 研究材料方面，本文采用野外采样与标本馆标本相结合的方式获得了中国蝾螈科2个重要保护物种繁殖群体的剪（指）趾材料，使得建立于其上的年龄结构工作更加可靠、更加具有代表性。 此外,本论文讨论了镇海棘螈瑞岩寺种群繁殖总量年度间的差异及其产生原因。将1998、1999、2000、2008、2009年镇海棘螈（Echinotriton chinhaiensis） 瑞岩寺种群的繁殖量进行比较，发现虽然雌性平均窝卵数比较稳定，但繁殖总量小于1998、1999、2000年任何一年总产卵量的50%。对2008年镇海棘螈繁殖量大幅下降的原因分析发现, 2007年9、10月影响严重台风的两次强台风、瑞岩寺景区开发等因素可能是造成近年该种群繁殖量大幅下降的原因。而2008年初50年不遇的低温是否影响镇海棘螈的繁殖值得进一步追踪研究。2009年繁殖量较2008年没有明显的增长，可能是由于2007年的台风影响了其繁殖营养的积累。台风的影响可能存在滞后现象,对此有待进一步监测证明。 本研究首次对中国蝾螈科物种进行的年龄结构鉴定，为进一步了解中国蝾螈科动物的种群生态打下了坚实的基础。 Using skeletochronology, we can know the life span of a species, age of reaching sexual mature, and of course age structure, which are vital(Morrison，et a1.，2004). Skeletochronology was performed on Echinotriton chinhaiensis Ruiyansi female population. The result shows that: The oldest individuals were 8 years old and the youngest ones were 3 years old. Individuals of age class 5(39.13%) and 6(21.74%) were most numerous. The number of individuals participated in reproduction decreased with the increase of age after the sixth year. Average age is 5.13 years. There is no correlation between age and body size (SVL and TL). For female chinhai salamander, energy is devoted to reproduction after reaching sexual maturation. While using skeletochronology to study Tylototriton taliangensis Liziping male population, the oldest individuals is 10 years old, and the youngest ones is 4 years old. Individuals of the age class 5, 6, and 7 dominat this population. The number of individuals decrease with the increase of age also after the seventh year. Average age is 6.7 years old in this population. there is also no correlation between age and body size (SVL and TL).It turned out that T. taliangensis tend to grow slowly after reaching sexual maturation. In this thesis, specimens from both wild and museum were used to gain enough toe clipping samples. A big sample size guarantees the reliability of this study. In the meantime, E. chinhaiensis’s annual reproduction of the year 1998, 1999, 2000 ,2008,and 2009 was compared. The result shows there is a huge decline in E. chinhaiensis’s annual reproduction in 2008,even the egg clutch is very stable. After analyzing, it turned out the huge decline in 2008 was probably caused by typhoon in 2007, besides the effect of tourism development and cash crop planting. While the impact of extreme weather of 2008 on reproduction needs further investigation. In the year 2009, there is no obvious increase in annual reproduction. It maybe due to lasting impact of typhoon in 2007. It is the first age-structure study on these two Chinese salamanders. A solid foundation was laid for further population ecology study of these two species.

Local Rotational Symmetries

This thesis describes a new representation for two-dimensional round regions called Local Rotational Symmetries. Local Rotational Symmetries are intended as a companion to Brady's Smoothed Local Symmetry Representation for elongated shapes. An algorithm for computing Local Rotational Symmetry representations at multiple scales of resolution has been implemented and results of this implementation are presented. These results suggest that Local Rotational Symmetries provide a more robustly computable and perceptually accurate description of round regions than previous proposed representations. In the course of developing this representation, it has been necessary to modify the way both Smoothed Local Symmetries and Local Rotational Symmetries are computed. First, grey-scale image smoothing proves to be better than boundary smoothing for creating representations at multiple scales of resolution, because it is more robust and it allows qualitative changes in representations between scales. Secondly, it is proposed that shape representations at different scales of resolution be explicitly related, so that information can be passed between scales and computation at each scale can be kept local. Such a model for multi-scale computation is desirable both to allow efficient computation and to accurately model human perceptions.

History of Baptist Indian missions : embracing remarks on the former and present condition of the aboriginal tribes; their settlement within the Indian Territory, and their future prospects / by Isaac McCoy.

http://www.archive.org/details/baptistindianmiss00mccorich