Prediction of steady-state flux through variably saturated zones within a septic absorption trench

This paper describes effluent flow dynamics within a septic absorption system and the prediction of flow through the biomat and sub-biomat zone. Using soil hydraulic properties in a one dimensional model we demonstrate how soil hydraulic properties interact with biomat resistances to determine long-term acceptance rate (LTAR). The LTAR is a key parameter used in the Australian and New Zealand Standard AS1547:2000 to calculate the area of trench required to ensure trenches are not overloaded. Results show that several orders of magnitude variation in saturated hydraulic conductivity (Ks) collapse to a one order of magnitude variation in LTAR. These results are calculated from a model using basic flow theory, allowing LTAR to be estimated for any combination of biomat resistance and soil hydraulic properties. To increase the reliability of prediction of septic trench hydrology, HYDRUS 2D was used to model two dimensional flow. For more permeable soils, the exfiltration zone above sidewall biomat growth is shown to be a key pathway for excess effluent flow.

Predicting changes in measured introcular pressure with non-contact tonometry after LASIK

Purpose: Optometrists are becoming more integrally involved in the diagnosis of and care for glaucoma patients in the UK. The correlation of apparent change in non contact tonometry (NCT) IOP measurement and change in other ocular parameters such as refractive error, corneal curvature, corneal thickness and treatment zone size (data available to optometrists after LASIK) would facilitate care of these patients. Setting: A UK Laser Eye Clinic. Methods: This is a retrospective study study of 200 sequential eyes with myopia with or without astigmatism which underwent LASIK using a Hansatome and an Alcon LADARvision 4000 excimer laser. Refraction keratometry, pachymetry and NCT IOP mesurements were taken before treatmebnt and agian 3 months after treatment. The relationship between these variables anfd teh treatment zones were studied using stepwise multiple regression analysis. Results: There was a mean difference of 5.54mmHg comnparing pre and postoperative NCT IOP. IOP change correlates with refractive error change (P < 0.001), preoperative corneal thickness (P < 0.001) and treatment zone size (P = 0.047). Preoperative corneal thickness correlates with preoperative IOP (P < 0.001) and postoperative IOP (P < 0.001). Using these correlations, the measured difference in NCT IIOP can be predicted preoperatively or postoperatively using derived equations.Conclusion: There is a significant reduction in measured NCT IOP after LASIK. The amount of reduction can be calculated using data acquired by optometrists. This is helpful for opthalmologists and optometrists who co-manage glaucoma patients who have had LASIK or with glaucoma pateints who are consideraing having LASIK.

Microstructural analysis of surface and interface zones in concrete

Several of OPC paste and concrete specimens, with different mix proportions, were cast against CPF and impermeable formwork (IF) and the profiles of pore structure, microhardness and scratch hardness of the cover zone were established. The chloride ingress and the depth of carbonation of the surface zone of concrete cast against CPF and IF were investigated. The main mechanisms controlling the ECR processes and the factors affecting such treatment were critically reviewed. Subsequently, as a means of restoring passivation of steel embedded in carbonated concrete, such HCP specimens were subjected to ECR. The influence of ECR on the chemistry of the pore solution and the microstructure of the surface and the steel/cement past interface zones were also studied. The main findings of this investigation were as follows: (a) The thickness of the microstructure gradient of cover concrete is significantly decreased with increasing period of water curing but is relatively unaffected by curing temperature, w/e ratio and the use of cement replacement materials. (b) The scratch hardness technique was shown to be potentially useful for characterising the microstructure and microhardness gradients of the surface zone. (c) A relationship between the microstructure gradient and mass transport properties of the surface zone was established. (d) The use of CPF resulted in a significant reduction in porosity of both the cement paste matrix and the aggregate/cement paste transition zone, and a marked improvement in the resistance of the surface zone to carbonation and the ingress of chloride ions. (e) The ECR treatment resulted in a marked densification of the pore structure and in changes to the pore solution chemistry and the cement phases of near-surface and steel/cement paste transition zones. This effect was more pronounced with current density, period of treatment and particularly with the use of sodium phosphate as an electrolyte.

The making of an ideology of the third way:the evolution of christian democracy in Germany (with special reference to 1945-49)

This study investigates the search for the third way in the history of German Christian Democracy. Today, in the United Kingdom, the 'third way' is seen as a new phenomenon, a synthesis of post-war belief in the welfare state and neo-liberal conservatism. Yet it insufficiently acknowledges that the origins of third way thinking, the marriage of social justice with free market economics, of individualism with collective responsibility, are found in the early philosophies of Catholic Social Theory and Protestant Social Ethical Teaching in Germany. This study shows that in the hundred years from the 1840s to the end of the 1940s, there were Catholic and Protestant socio-ethical thinkers and political reformists in Germany who attempted to bridge the philosophical differences between liberalism and socialism, to develop a socio-economic order based on Christian moral values. It will focus on the period 1945-1949, when the CDU was founded as the first interdenominational, Christian party. The study provides the first comprehensive account of the political debates in Christian democratic groups in the Soviet, British, French and American allied occupied zones, also giving equal attention to the contribution from the Protestant wing, alongside the more widely acknowledged role of Catholics in the birth of the CDU. It examines how Christian Democrats envisaged correcting the aberrations of German history, by uniting all social classes and Christian religions in one all-embracing Volkspartei, and transforming party politics from its earlier obsession with sectarian and ideological interests towards a more pragmatic 'third way' programme. The study argues that through the making of its ideology, the CDU modified the nation's understanding of its history, re-interpreted its traditions, and redefined the meaning and perception of established political philosophies. This reveals how the ambiguity of political terminology, and the flexible practice of 'third way' politics, were an invaluable political resource in the CDU's campaign for unity, ideological legitimisation and political power.

International business research and risky investments, an analysis of FDI in conflict zones

The purpose of this paper is to examine the determinants of a firm's strategy to invest in a conflict location. To the best of our knowledge, this has not been done before. We examine this using a standard model of international business, overlaid with the fundamental approach to corporate social responsibility. We start with the population of multinationals who have chosen to invest in low income countries with weak institutions. We then split this sample in order to distinguish between firms that have invested in conflict regions compared to those that have not. Our analysis then proceeds to explain the decision of those firms to invest in conflict locations using a simple Probit model. We find that countries with weaker institutions and less concern about corporate social responsibility (CSR) are more likely to invest in conflict regions. Finally, firms with more concentrated ownership are more likely to invest in such locations. © 2012 Elsevier Ltd.

Investing in conflict zones:a firm-level analysis

The purpose of this paper is to examine, using panel data econometric techniques, the determinants of a firm’s strategy to invest in a conflict location. To the best of our knowledge this has not been done before. We use a large database of firm-level data that includes 2858 multinational firms that have a subsidiary in a developing country (during 1999-2006). Out of these firms 290 are classified as having a subsidiary in a conflict location. The choice of a conflict location is based on data from the Inter Country Risk Guide (ICRG). We start with the population of multinationals who have chosen to invest in low income countries with weak institutions. Our analysis then proceeds to explain the decision of those firms to invest in conflict locations. We have four hypotheses: (1) Firms with concentrated ownership are more likely to invest in a conflict region; (2) Firms from countries with weaker institutions are more likely to invest in conflict regions; (3) Firms and Countries with less concern over corporate social responsibility are more likely to invest in conflict countries; and (4) that there is large sector level differences in the propensity to invest in a conflict region. The results suggest that all of these hypotheses can be confirmed.

Hurricane Wilma’s impact on overall soil elevation and zones within the soil profile in a mangrove forest

Soil elevation affects tidal inundation period, inundation frequency, and overall hydroperiod, all of which are important ecological factors affecting species recruitment, composition, and survival in wetlands. Hurricanes can dramatically affect a site’s soil elevation. We assessed the impact of Hurricane Wilma (2005) on soil elevation at a mangrove forest location along the Shark River in Everglades National Park, Florida, USA. Using multiple depth surface elevation tables (SETs) and marker horizons we measured soil accretion, erosion, and soil elevation. We partitioned the effect of Hurricane Wilma’s storm deposit into four constituent soil zones: surface (accretion) zone, shallow zone (0–0.35 m), middle zone (0.35–4 m), and deep zone (4–6 m). We report expansion and contraction of each soil zone. Hurricane Wilma deposited 37.0 (±3.0 SE) mm of material; however, the absolute soil elevation change was + 42.8 mm due to expansion in the shallow soil zone. One year post-hurricane, the soil profile had lost 10.0 mm in soil elevation, with 8.5 mm of the loss due to erosion. The remaining soil elevation loss was due to compaction from shallow subsidence. We found prolific growth of new fine rootlets (209 ± 34 SE g m−2) in the storm deposited material suggesting that deposits may become more stable in the near future (i.e., erosion rate will decrease). Surficial erosion and belowground processes both played an important role in determining the overall soil elevation. Expansion and contraction in the shallow soil zone may be due to hydrology, and in the middle and bottom soil zones due to shallow subsidence. Findings thus far indicate that soil elevation has made substantial gains compared to site specific relative sea-level rise, but data trends suggest that belowground processes, which differ by soil zone, may come to dominate the long term ecological impact of storm deposit.

Seismic Retrofitting of a Historic Structure with Limited Construction Documentation

Many buildings constructed during the middle of the 20th century were constructed with criteria that fall short of current requirements. Although shortcomings are possible in all aspects of the design, the inadequacies in terms of seismic design present a more pressing issue to human life. This risk has been seen in various earthquakes that have struck Italy recently, and subsequently, the codes have been altered to account for this underestimated danger. Structures built after these changes remain at risk and must be retrofitted depending on their use. This report centers around the Giovanni Michelucci Institute of Mathematics at the University of Bologna and the work required to modify the building so that it can withstand 60% of the current design requirements. The goal of this particular report is to verify the previous reports written in Italian and present an accurate analysis along with intervention suggestions for this particular building. The work began with an investigation into the previous sources and work to find out how the structure had been interpreted. After understanding the building, corrections were made where required, and the failing elements were organized graphically to more easily show where the building needed the most work. Once the critical zones were mapped, remediation techniques were tested on the top floor, and the modeling techniques and effects of the interventions were presented to assist in further work on the structure.

Geochemical parameters of sediments and waters in areas of ocean barrier zones

Geochemical barrier zones play an important role in determining various physical systems and characteristics of oceans, e.g. hydrodynamics, salinity, temperature and light. In the book each of more than 30 barrier zones are illustrated and defined by physical, chemical and biological parameters. Among the topics discussed are processes of inflow, transformation and precipitation of the sedimentary layer of the open oceans and more restricted areas such as the Baltic, Black and Mediterranean Seas.

Nutritional status of lactating mothers and their children 6-23 months of age in pre- and post-harvest seasons in two agro-ecological zones of rural Ethiopia

The objective of this study was to assess seasonal variation in nutritional status and feeding practices among lactating mothers and their children 6-23 months of age in two different agro-ecological zones of rural Ethiopia (lowland zone and midland zone). Food availability and access are strongly affected by seasonality in Ethiopia. However, there are few published data on the effects of seasonal food fluctuations on nutritional status and dietary diversity patterns of mothers and children in rural Ethiopia. A longitudinal study was conducted among 216 mothers in two agro-ecological zones of rural Ethiopia during pre and post-harvest seasons. Data were collected on many parameters including anthropometry, blood levels of haemoglobin and ferritin and zinc, urinary iodine levels, questionnaire data regarding demographic and household parameters and health issues, and infant and young child feeding practices, 24 h food recall to determine dietary diversity scores, and household use of iodized salt. Chi-square and multivariable regression models were used to identify independent predictors of nutritional status. A wide variety of results were generated including the following highlights. It was found that 95.4% of children were breastfed, of whom 59.7% were initially breastfed within one hour of birth, 22.2% received pre-lacteal feeds, and 50.9% of children received complementary feedings by 6 months of age. Iron deficiency was found in 44.4% of children and 19.8% of mothers. Low Zinc status was found in 72.2% of children and 67.3% of mothers. Of the study subjects, 52.5% of the children and 19.1% of the mothers were anaemic, and 29.6% of children and 10.5% of mothers had iron deficiency anaemia. Among the mothers with low serum iron status, 81.2% and 56.2% of their children had low serum zinc and iron, respectively. Similarly, among the low serum zinc status mothers, 75.2% and 45.3% of their children had low serum in zinc and iron, respectively. There was a strong correlation between the micronutrient status of the mothers and the children for ferritin, zinc and haemoglobin (P <0.001). There was also statistically significant difference between agro-ecological zones for micronutrient deficiencies among the mothers (p<0.001) but not for their children. The majority (97.6%) of mothers in the lowland zone were deficient in at least one micronutrient biomarker (zinc or ferritin or haemoglobin). Deficiencies in one, two, or all three biomarkers of micronutrient status were observed in 48.1%, 16.7% and 9.9% of mothers and 35.8%, 29.0%, and 23.5%, of children, respectively. Additionally, about 42.6% of mothers had low levels of urinary iodine and 35.2% of lactating mothers had goitre. Total goitre prevalence rates and urinary iodine levels of lactating mothers were not significantly different across agro-ecological zones. Adequately iodised salt was available in 36.6% of households. The prevalence of anaemia increased from post-harvest (21.8%) to pre-harvest seasons (40.9%) among lactating mothers. Increases were from 8.6% to 34.4% in midland and from 34.2% to 46.3% in lowland agro-ecological zones. Fifteen percent of mothers were anaemic during both seasons. Predictors of anaemia were high parity of mother and low dietary diversity. The proportion of stunted and underweight children increased from 39.8% and 27% in post-harvest season to 46.0% and 31.8% in pre-harvest season, respectively. However, wasting in children decreased from 11.6% to 8.5%. Major variations in stunting and underweight were noted in midland compared to lowland agroecological zones. Anthropometric measurements in mothers indicated high levels of undernutrition. The prevalence of undernutrition in mothers (BMI <18.5kg/m2) increased from 41.7 to 54.7% between post- and pre-harvest seasons. The seasonal effect was generally higher in the midland community for all forms of malnutrition. Parity, number of children under five years and regional variation were predictors of low BMI among lactating mothers. There were differences in minimum meal frequency, minimum acceptable diet and dietary diversity in children in pre-harvest and post-harvest seasons and these parameters were poor in both seasons. Dietary diversity among mothers was higher in lowland zone but was poor in both zones across the seasons. In conclusion, malnutrition and micronutrient deficiencies are very prevalent among lactating mothers and their children 6-23 months old in the study areas. There are significant seasonal variations in malnutrition and dietary diversity, in addition to significant differences between lowland and midland agro-ecological zones. These findings suggest a need to design effective preventive public health nutrition programs to address both the mothers’ and children’s needs particularly in the preharvest season.

Create, Establish, Maintain: Comparing Zones of Peace in the Nordic Area and the Southern Cone

In the wake of the Cold War, regional organizations have proliferated and are now a dominant theme in global politics. This study tests whether explanations for the Nordic peace can help to understand or construct other zones of peace in these increasingly important regional settings. With that in mind, this study compares the Nordic area of Denmark, Finland, Iceland, Norway, and Sweden with the Southern Cone region–here defined as Argentina, Chile, Paraguay, and Uruguay–and both are treated as regional, subsystemic zones of peace. Its significance lies in analysis of two developmentally disparate regions not yet compared in zones of peace literature. Using structured, focused comparison, this study is guided by fundamental questions about each region that assess the relationship between explanations for regional peace and their respective historical records. Understanding the conditions that permit the endurance of peace in today’s global context has far-reaching empirical and theoretical implications.

Simulating Granite Emplacement and Deformation with Centrifuge Analogue Modelling

The Greater Himalayan leucogranites are a discontinuous suite of intrusions emplaced in a thickened crust during the Miocene southward ductile extrusion of the Himalayan metamorphic core. Melt-induced weakening is thought to have played a critical role in strain localization that facilitated the extrusion. Recent advancements in centrifuge analogue modelling techniques allow for the replication of a broader range of crustal deformation behaviors, enhancing our understanding of large hot orogens. Polydimethylsiloxane (PDMS) is commonly used in centrifuge experiments to model weak melt zones. Difficulties in handling PDMS had, until now, limited its emplacement in models prior to any deformation. A new modelling technique has been developed where PDMS is emplaced into models that have been subjected to some shortening. This technique aims to better understand the effects of melt on strain localization and potential decoupling between structural levels within an evolving orogenic system. Models are subjected to an early stage of shortening, followed by the introduction of PDMS, and then a final stage of shortening. Theoretical percentages of partial melt and their effect on rock strength are considered when adding a specific percentage of PDMS in each model. Due to the limited size of the models, only PDMS sheets of 3 mm thickness were used, which varied in length and width. Within undeformed packages, minimal surface and internal deformation occurred when PDMS is emplaced in the lower layer of the model, showing a vertical volume increase of ~20% within the package; whereas the emplacement of PDMS into the middle layer showed internal dragging of the middle laminations into the lower layer and a vertical volume increase ~30%. Emplacement of PDMS results in ~7% shortening for undeformed and deformed models. Deformed models undergo ~20% additional shortening after two rounds of deformation. Strain localization and decoupling between units occur in deformed models where the degree of deformation changes based on the amount of partial melt present. Surface deformation visible by the formation of a bulge, mode 1 extension cracks and varying surface strain ellipses varies depending if PDMS is present. Better control during emplacement is exhibited when PDMS is added into cooler models, resulting in reduced internal deformation within the middle layer.

Potential Shifts in Canadian High Arctic Sedimentary Organic Matter Composition With Permafrost Active Layer Detachments

Increased temperature and precipitation in Arctic regions have led to deeper thawing and structural instability in permafrost soil. The resulting localized disturbances, referred to as active layer detachments (ALDs), may transport organic matter (OM) to more biogeochemically active zones. To examine this further, solid state cross polarization magic angle spinning 13C nuclear magnetic resonance (CPMAS NMR) and biomarker analysis were used to evaluate potential shifts in riverine sediment OM composition due to nearby ALDs within the Cape Bounty Arctic Watershed Observatory, Nunavut, Canada. In sedimentary OM near ALDs, NMR analysis revealed signals indicative of unaltered plant-derived material, likely derived from permafrost. Long chain acyclic aliphatic lipids, steroids, cutin, suberin and lignin occurred in the sediments, consistent with a dominance of plant-derived compounds, some of which may have originated from permafrost-derived OM released by ALDs. OM degradation proxies for sediments near ALDs revealed less alteration in acyclic aliphatic lipids, while constituents such as steroids, cutin, suberin and lignin were found at a relatively advanced stage of degradation. Phospholipid fatty acid analysis indicated that microbial activity was higher near ALDs than downstream but microbial substrate limitation was prevalent within disturbed regions. Our study suggests that, as these systems recover from disturbance, ALDs likely provide permafrost-derived OM to sedimentary environments. This source of OM, which is enriched in labile OM, may alter biogeochemical patterns and enhance microbial respiration within these ecosystems.

Retinal nerve fiber layer analysis using GDx® in 49 patients with chronic phase DUSN

To describe retinal nerve fiber layer changes in late-stage diffuse unilateral subacute neuroretinitis eyes and compare these results with healthy eyes observed through nerve fiber analyzer (GDx®). Methods: This is a retrospective case-control study in which 49 eyes in late-stage diffuse unilateral subacute neuroretinitis were examined from May/97 to December/ 01. First, eyes with diffuse unilateral subacute neuroretinitis and healthy contralateral eyes (Control Group I) were statistically matched. Subsequently, eyes with diffuse unilateral subacute neuroretinitis were compared with eyes of healthy patients (Control Group II). Results: Eyes from Control Groups I and II had higher relative frequency of “within normal limits” status. Eyes from the diffuse unilateral subacute neuroretinitis (DUSN) Group had higher frequency of “outside normal limits” and “borderline” status. Control Groups I and II had absolute values different from the DUSN Group regarding all parameters (p<0.05), except for Symmetry in Control Groups I and II, Average thickness and Superior Integral in control group II. Conclusion: Patients with late-stage diffuse unilateral subacute neuroretinitis presented presumed decrease in nerve fiber layer thickness shown by GDx®. Retinal zones with larger vascular support and larger amount of nerve fibers presented higher decrease in the delay of the reflected light measured by the nerve fiber analyzer

Stratégie d'amélioration de la résistance mécanique des zones de connecteurs

Le bois subit une demande croissante comme matériau de construction dans les bâtiments de grandes dimensions. Ses qualités de matériau renouvelable et esthétique le rendent attrayant pour les architectes. Lorsque comparé à des produits fonctionnellement équivalents, il apparait que le bois permet de réduire la consommation d’énergie non-renouvelable. Sa transformation nécessite une quantité d’énergie inférieure que l’acier et le béton. Par ailleurs, par son origine biologique, une structure en bois permet de stocker du carbone biogénique pour la durée de vie du bâtiment. Maintenant permis jusqu’à six étages de hauteur au Canada, les bâtiments de grande taille en bois relèvent des défis de conception. Lors du dimensionnement des structures, les zones des connecteurs sont souvent les points critiques. Effectivement, les contraintes y sont maximales. Les structures peuvent alors apparaitre massives et diminuer l’innovation architecturale. De nouvelles stratégies doivent donc être développées afin d’améliorer la résistance mécanique dans les zones de connecteurs. Différents travaux ont récemment porté sur la création ou l’amélioration de types d’assemblage. Dans cette étude, l’accent est mis sur le renforcement du bois utilisé dans la région de connexion. L’imprégnation a été choisie comme solution de renfort puisque la littérature démontre qu’il est possible d’augmenter la dureté du bois avec cette technique. L’utilisation de cette stratégie de renfort sur l’épinette noire (Picea Mariana (Mill.) BSP) pour une application structurale est l’élément de nouveauté dans cette recherche. À défaut d’effectuer une imprégnation jusqu’au coeur des pièces, l’essence peu perméable de bois employée favorise la création d’une mince couche en surface traitée sans avoir à utiliser une quantité importante de produits chimiques. L’agent d’imprégnation est composé de 1,6 hexanediol diacrylate, de triméthylopropane tricacrylate et d’un oligomère de polyester acrylate. Une deuxième formulation contenant des nanoparticules de SiO2 a permis de vérifier l’effet des nanoparticules sur l’augmentation de la résistance mécanique du bois. Ainsi, dans ce projet, un procédé d’imprégnation vide-pression a servi à modifier un nouveau matériau à base de bois permettant des assemblages plus résistants mécaniquement. Le test de portance locale à l’enfoncement parallèle au fil d’un connecteur de type tige a été réalisé afin de déterminer l’apport du traitement sur le bois utilisé comme élément de connexion. L’effet d’échelle a été observé par la réalisation du test avec trois diamètres de boulons différents (9,525 mm, 12,700 mm et 15,875 mm). En outre, le test a été effectué selon un chargement perpendiculaire au fil pour le boulon de moyen diamètre (12,700 mm). La corrélation d’images numériques a été utilisée comme outil d’analyse de la répartition des contraintes dans le bois. Les résultats ont démontré une portance du bois plus élevée suite au traitement. Par ailleurs, l’efficacité est croissante lorsque le diamètre du boulon diminue. C’est un produit avec une valeur caractéristique de la portance locale parallèle au fil de 79% supérieure qui a été créé dans le cas du test avec le boulon de 9,525 mm. La raideur du bois a subi une augmentation avoisinant les 30%. Suite au traitement, la présence d’une rupture par fissuration est moins fréquente. Les contraintes se distribuent plus largement autour de la région de connexion. Le traitement n’a pas produit d’effet significatif sur la résistance mécanique de l’assemblage dans le cas d’un enfoncement du boulon perpendiculairement au fil du bois. De même, l’effet des nanoparticules en solution n’est pas ressorti significatif. Malgré une pénétration très faible du liquide à l’intérieur du bois, la couche densifiée en surface créée suite au traitement est suffisante pour produire un nouveau matériau plus résistant dans les zones de connexion. Le renfort du bois dans la région des connecteurs doit influencer le dimensionnement des structures de grande taille. Avec des éléments de connexion renforcés, il sera possible d’allonger les portées des poutres, multipliant ainsi les possibilités architecturales. Le renfort pourra aussi permettre de réduire les sections des poutres et d’utiliser une quantité moindre de bois dans un bâtiment. Cela engendrera des coûts de transport et des coûts reliés au temps d’assemblage réduits. De plus, un connecteur plus résistant permettra d’être utilisé en moins grande quantité dans un assemblage. Les coûts d’approvisionnement en éléments métalliques et le temps de pose sur le site pourront être revus à la baisse. Les avantages d’un nouveau matériau à base de bois plus performant utilisé dans les connexions permettront de promouvoir le bois dans les constructions de grande taille et de réduire l’impact environnemental des bâtiments.