Differential effects of internal and external factors on the development of vocabulary, tense morphology and morpho-syntax in successive bilingual children

The present study investigates the effects of child internal (age/time) and child external/environmental factors on the development of a wide range of language domains in successive bilingual (L2) Turkish-English children of homogeneously low SES. Forty-three L2 children were tested on standardized assessments examining the acquisition of vocabulary and morpho-syntax. The L2 children exhibited a differential acquisition of the various domains: they were better on the general comprehension of grammar and tense morphology and less accurate on the acquisition of vocabulary and (complex) morpho-syntax. Profile effects were confirmed by the differential effects of internal and external factors on the language domains. The development of vocabulary and complex syntax were affected by internal and external factors, whereas external factors had no contribution to the development of tense morphology. These results are discussed in light of previous studies on the impact of internal and external factors in child L2 acquisition.

Optimizing layer-by-layer deposition of interpolymer complexes on solid substrates using Biacore

The layer-by-layer deposition of polymers onto surfaces allows the fabrication of multilayered materials for a wide range of applications, from drug delivery to biosensors. This work describes the analysis of complex formation between poly(acrylic acid) and methylcellulose in aqueous solutions using Biacore, a surface plasmon resonance analytical technique, traditionally used to examine biological interactions. This technique characterized the layer-by-layer deposition of these polymers on the surface of a Biacore sensor chip. The results were subsequently used to optimize the experimental conditions for sequential layer deposition on glass slides. The role of the solution pH and poly(acrylic acid) molecular weight on the formation of interpolymer multilayered coatings was researched, and showed that the optimal deposition of the polymer complexes was achieved at pHs ≤2.5 with a poly(acrylic acid) molecular weight of 450 kDa.

Antigenotoxicity of probiotics and prebiotics on faecal water-induced DNA damage in human colon adenocarcinoma cells

Six strains of lactic acid producing bacteria (LAB) were incubated (1 x 10(8)cfu/ml) with genotoxic faecal water from a human subject. HT29 human adenocarcinoma cells were then challenged with the resultant samples and DNA damage measured using the single cell gel electrophoresis (comet) assay. The LAB strains investigated were Bifidobacterium sp. 420, Bifidobacterium Bb12, Lactobacillus plantarum, Streptococcus thermophilus, Lactobacillus bulgaricus and Enterococcus faecium. DNA damage was significantly decreased by all bacteria used with the exception of Strep. thermophilus. Bif. Bb12 and Lact. plantarum showed the greatest protective effect against DNA damage. Incubation of faecal water with different concentrations of Bif. Bb12 and Lact. plantarum revealed that the decrease in genotoxicity was related to cell density. Non-viable (heat treated) probiotic cells had no effect on faecal water genotoxicity. In a second study, HT29 cells were cultured in the presence of supernatants of incubations of probiotics with various carbohydrates including known prebiotics; the HT29 cells were then exposed to faecal water. Overall, incubations involving Lact. plantarum with the fructooligosaccharide (FOS)-based prebiotics Inulin, Raftiline, Raftilose and Actilight were the most effective in increasing the cellular resistance to faecal water genotoxicity, whereas fermentations with Elixor (a galactooligosaccharide) and Fibersol (a maltodextrin) were less effective. Substantial reductions in faecal water-induced DNA damage were also seen with supernatants from incubation of prebiotics with Bif. Bb12. The supernatant of fermentations involving Ent. faecium and Bif. sp. 420 generally had less potent effects on genotoxicity although some reductions with Raftiline and Elixor fermentations were apparent.

Genes driving potato tuber initiation and growth: identification based on transcriptional changes using the POCI array

The increasing amount of available expressed gene sequence data makes whole-transcriptome analysis of certain crop species possible. Potato currently has the second largest number of publicly available expressed sequence tag (EST) sequences among the Solanaceae. Most of these ESTs, plus other proprietary sequences, were combined and used to generate a unigene assembly. The set of 246,182 sequences produced 46,345 unigenes, which were used to design a 44K 60-mer oligo array (Potato Oligo Chip Initiative: POCI). In this study, we attempt to identify genes controlling and driving the process of tuber initiation and growth by implementing large-scale transcriptional changes using the newly developed POCI array. Major gene expression profiles could be identified exhibiting differential expression at key developmental stages. These profiles were associated with functional roles in cell division and growth. A subset of genes involved in the regulation of the cell cycle, based on their Gene Ontology classification, exhibit a clear transient upregulation at tuber onset indicating increased cell division during these stages. The POCI array allows the study of potato gene expression on a much broader level than previously possible and will greatly enhance analysis of transcriptional control mechanisms in a wide range of potato research areas. POCI sequence and annotation data are publicly available through the POCI database (http://pgrc.ipk-gatersleben.de/poci).

First human hNT astrocytes patterned to single cell resolution on parylene-C/Silicon dioxide substrates

In our previous work we developed a successful protocol to pattern the human hNT neuron (derived from the human teratocarcinoma cell line (hNT)) on parylene-C/SiO2 substrates. This communication, reports how we have successfully managed to pattern the supportive cell to the neuron, the hNT astrocyte, on such substrates. Here we disseminate the nanofabrication, cell differentiation and cell culturing protocols necessary to successfully pattern the first human hNT astrocytes to single cell resolution on parylene-C/SiO2 substrates. This is performed for varying parylene strip widths providing excellent contrast to the SiO2 substrate and elegant single cell isolation at 10μm strip widths. The breakthrough in patterning human cells on a silicon chip has widespread implications and is valuable as a platform technology as it enables a detailed study of the human brain at the cellular and network level.

Examining second language development using event-related potentials: a cross-sectional study on the processing of gender and number agreement

This cross-sectional study examines the role of L1-L2 differences and structural distance in the processing of gender and number agreement by English-speaking learners of Spanish at three different levels of proficiency. Preliminary results show that differences between the L1 and L2 impact L2 development, as sensitivity to gender agreement violations, as opposed to number agreement violations, emerges only in learners at advanced levels of proficiency. Results also show that the establishment of agreement dependencies is impacted by the structural distance between the agreeing elements for native speakers and for learners at intermediate and advanced levels of proficiency but not for low proficiency. The overall pattern of results suggests that the linguistic factors examined here impact development but do not constrain ultimate attainment; for advanced learners, results suggest that second language processing is qualitatively similar to native processing.

Effects of dense code-switching on executive control

Bilingualism is reported to re-structure executive control networks, but it remains unknown which aspects of the bilingual experience cause this modulation. This study explores the impact of three code-switching types on executive functions: (1) alternation of languages, (2) insertion of lexicon of one language into grammar of another, (3) dense code-switching with co-activation of lexicon and grammar. Current models hypothesise that they challenge different aspects of the executive system because they vary in the extent and scope of language separation. Two groups of German-English bilinguals differing in dense code-switching frequency participated in a flanker task under conditions varying in degree of trial-mixing and resulting demands to conflict-monitoring. Bilinguals engaging in more dense code-switching showed inhibitory advantages in the condition requiring most conflict-monitoring. Moreover, dense code-switching frequency correlated positively with monitoring skills. This suggests that the management of co-activated languages during dense code-switching engages conflict-monitoring and that the consolidation processes taking place within co-activated linguistic systems involve local inhibition. Code-switching types requiring greater degrees of language separation may involve more global forms of inhibition. This study shows that dense code-switching is a key experience shaping bilinguals’ executive functioning and highlights the importance of controlling for participants’ code-switching habits in bilingualism research.

Fabrication and integration of planar electrodes for contactless conductivity detection on polyester-toner electrophoresis microchips

In this report, we describe the microfabrication and integration of planar electrodes for contactless conductivity detection on polyester-toner (PT) electrophoresis microchips using toner masks. Planar electrodes were fabricated by three simple steps: (i) drawing and laser-printing the electrode geometry on polyester films, (ii) sputtering deposition onto substrates, and (iii) removal of toner layer by a lift-off process. The polyester film with anchored electrodes was integrated to PT electrophoresis microchannels by lamination at 120 degrees C in less than 1 min. The electrodes were designed in an antiparallel configuration with 750 mu m width and 750 gm gap between them. The best results were recorded with a frequency of 400 kHz and 10 V-PP using a sinusoidal wave. The analytical performance of the proposed microchip was evaluated by electrophoretic separation of potassium, sodium and lithium in 150 mu m wide x 6 mu m deep microchannels. Under an electric field of 250 V/cm the analytes were successfully separated in less than 90 s with efficiencies ranging from 7000 to 13 000 plates. The detection limits (S/N = 3) found for K+, Na+, and Li+ were 3.1, 4.3, and 7.2 mu mol/L, respectively. Besides the low-cost and instrumental simplicity, the integrated PT chip eliminates the problem of manual alignment and gluing of the electrodes, permitting more robustness and better reproducibility, therefore, more suitable for mass production of electrophoresis microchips.

View of Lithography Lab at the New York Trade School

Part of a lithography lab at the New York Trade School is depicted in this photograph. To the right sample prints are hung on a board, while other prints can be seen on the table, possibly drying. Black and white photograph.

Clustering Lab value working with medical data

Data mining is a relatively new field of research that its objective is to acquire knowledge from large amounts of data. In medical and health care areas, due to regulations and due to the availability of computers, a large amount of data is becoming available [27]. On the one hand, practitioners are expected to use all this data in their work but, at the same time, such a large amount of data cannot be processed by humans in a short time to make diagnosis, prognosis and treatment schedules. A major objective of this thesis is to evaluate data mining tools in medical and health care applications to develop a tool that can help make rather accurate decisions. In this thesis, the goal is finding a pattern among patients who got pneumonia by clustering of lab data values which have been recorded every day. By this pattern we can generalize it to the patients who did not have been diagnosed by this disease whose lab values shows the same trend as pneumonia patients does. There are 10 tables which have been extracted from a big data base of a hospital in Jena for my work .In ICU (intensive care unit), COPRA system which is a patient management system has been used. All the tables and data stored in German Language database.

TCA Evaluation : Lab Measurements, Modelling and System Simulations

The study reported here is part of a large project for evaluation of the Thermo-Chemical Accumulator (TCA), a technology under development by the Swedish company ClimateWell AB. The studies concentrate on the use of the technology for comfort cooling. This report concentrates on measurements in the laboratory, modelling and system simulation. The TCA is a three-phase absorption heat pump that stores energy in the form of crystallised salt, in this case Lithium Chloride (LiCl) with water being the other substance. The process requires vacuum conditions as with standard absorption chillers using LiBr/water. Measurements were carried out in the laboratories at the Solar Energy Research Center SERC, at Högskolan Dalarna as well as at ClimateWell AB. The measurements at SERC were performed on a prototype version 7:1 and showed that this prototype had several problems resulting in poor and unreliable performance. The main results were that: there was significant corrosion leading to non-condensable gases that in turn caused very poor performance; unwanted crystallisation caused blockages as well as inconsistent behaviour; poor wetting of the heat exchangers resulted in relatively high temperature drops there. A measured thermal COP for cooling of 0.46 was found, which is significantly lower than the theoretical value. These findings resulted in a thorough redesign for the new prototype, called ClimateWell 10 (CW10), which was tested briefly by the authors at ClimateWell. The data collected here was not large, but enough to show that the machine worked consistently with no noticeable vacuum problems. It was also sufficient for identifying the main parameters in a simulation model developed for the TRNSYS simulation environment, but not enough to verify the model properly. This model was shown to be able to simulate the dynamic as well as static performance of the CW10, and was then used in a series of system simulations. A single system model was developed as the basis of the system simulations, consisting of a CW10 machine, 30 m2 flat plate solar collectors with backup boiler and an office with a design cooling load in Stockholm of 50 W/m2, resulting in a 7.5 kW design load for the 150 m2 floor area. Two base cases were defined based on this: one for Stockholm using a dry cooler with design cooling rate of 30 kW; one for Madrid with a cooling tower with design cooling rate of 34 kW. A number of parametric studies were performed based on these two base cases. These showed that the temperature lift is a limiting factor for cooling for higher ambient temperatures and for charging with fixed temperature source such as district heating. The simulated evacuated tube collector performs only marginally better than a good flat plate collector if considering the gross area, the margin being greater for larger solar fractions. For 30 m2 collector a solar faction of 49% and 67% were achieved for the Stockholm and Madrid base cases respectively. The average annual efficiency of the collector in Stockholm (12%) was much lower than that in Madrid (19%). The thermal COP was simulated to be approximately 0.70, but has not been possible to verify with measured data. The annual electrical COP was shown to be very dependent on the cooling load as a large proportion of electrical use is for components that are permanently on. For the cooling loads studied, the annual electrical COP ranged from 2.2 for a 2000 kWh cooling load to 18.0 for a 21000 kWh cooling load. There is however a potential to reduce the electricity consumption in the machine, which would improve these figures significantly. It was shown that a cooling tower is necessary for the Madrid climate, whereas a dry cooler is sufficient for Stockholm although a cooling tower does improve performance. The simulation study was very shallow and has shown a number of areas that are important to study in more depth. One such area is advanced control strategy, which is necessary to mitigate the weakness of the technology (low temperature lift for cooling) and to optimally use its strength (storage).

Informal sanctions and conditional cooperation: : A natural experiment on voluntary contributions to a public good.

In a natural experiment, this paper studies the impact of an informal sanctioning mechanism on individuals’ voluntary contribution to a public good. Cross-country skiers’ actual cash contributions in two ski resorts, one with and one without an informal sanctioning system, are used. I find the contributing share to be higher in the informal sanctioning system (79 percent) than in the non-sanctioning system (36 percent). Previous studies in one-shot public good situations have found an increasing conditional contribution (CC) function, i.e. the relationship between expected average contributions of other group members and the individual’s own contribution. In contrast, the present results suggest that the CC-function in the non-sanctioning system is non-increasing at high perceived levels of others’ contribution. This relationship deserves further testing in lab.

Carpentry Lab

This shows a view of the Carpentry Lab at the New York Trade School. Students can be seen working on a number of different projects. Black and white photograph.

Redes-em-Chip : arquiteturas e modelos para avaliação de área e desempenho

Com o advento dos processos submicrônicos, a capacidade de integração de transistores tem atingido níveis que possibilitam a construção de um sistema completo em uma única pastilha de silício. Esses sistemas, denominados sistemas integrados, baseiam-se no reuso de blocos previamente projetados e verificados, os quais são chamados de núcleos ou blocos de propriedade intelectual. Os sistemas integrados atuais incluem algumas poucas dezenas de núcleos, os quais são interconectados por meio de arquiteturas de comunicação baseadas em estruturas dedicadas de canais ponto-a-ponto ou em estruturas reutilizáveis constituídas por canais multiponto, denominadas barramentos. Os futuros sistemas integrados irão incluir de dezenas a centenas de núcleos em um mesmo chip com até alguns bilhões de transistores, sendo que, para atender às pressões do mercado e amortizar os custos de projeto entre vários sistemas, é importante que todos os seus componentes sejam reutilizáveis, incluindo a arquitetura de comunicação. Das arquiteturas utilizadas atualmente, o barramento é a única que oferece reusabilidade. Porém, o seu desempenho em comunicação e o seu consumo de energia degradam com o crescimento do sistema. Para atender aos requisitos dos futuros sistemas integrados, uma nova alternativa de arquitetura de comunicação tem sido proposta na comunidade acadêmica. Essa arquitetura, denominada rede-em-chip, baseia-se nos conceitos utilizados nas redes de interconexão para computadores paralelos. Esta tese se situa nesse contexto e apresenta uma arquitetura de rede-em-chip e um conjunto de modelos para a avaliação de área e desempenho de arquiteturas de comunicação para sistemas integrados. A arquitetura apresentada é denominada SoCIN (System-on-Chip Interconnection Network) e apresenta como diferencial o fato de poder ser dimensionada de modo a atender a requisitos de custo e desempenho da aplicação alvo. Os modelos desenvolvidos permitem a estimativa em alto nível da área em silício e do desempenho de arquiteturas de comunicação do tipo barramento e rede-em-chip. São apresentados resultados que demonstram a efetividade das redes-em-chip e indicam as condições que definem a aplicabilidade das mesmas.