The design and engineering of a reactor test facility for thermal processing of biomass

This thesis describes the design and engineering of a pressurised biomass gasification test facility. A detailed examination of the major elements within the plant has been undertaken in relation to specification of equipment, evaluation of options and final construction. The retrospective project assessment was developed from consideration of relevant literature and theoretical principles. The literature review includes a discussion on legislation and applicable design codes. From this analysis, each of the necessary equipment units was reviewed and important design decisions and procedures highlighted and explored. Particular emphasis was placed on examination of the stringent demands of the ASME VIII design codes. The inter-relationship of functional units was investigated and areas of deficiency, such as biomass feeders and gas cleaning, have been commented upon. Finally, plant costing was summarized in relation to the plant design and proposed experimental programme. The main conclusion drawn from the study is that pressurised gasification of biomass is far more difficult and expensive to support than atmospheric gasification. A number of recommendations have been made regarding future work in this area.

Drying processess in the United Kingdom:assessment of industrial energy utilisation and efficiency of drying systems and the modelling of drying characters using neural networks (BL)

Drying is an important unit operation in process industry. Results have suggested that the energy used for drying has increased from 12% in 1978 to 18% of the total energy used in 1990. A literature survey of previous studies regarding overall drying energy consumption has demonstrated that there is little continuity of methods and energy trends could not be established. In the ceramics, timber and paper industrial sectors specific energy consumption and energy trends have been investigated by auditing drying equipment. Ceramic products examined have included tableware, tiles, sanitaryware, electrical ceramics, plasterboard, refractories, bricks and abrasives. Data from industry has shown that drying energy has not varied significantly in the ceramics sector over the last decade, representing about 31% of the total energy consumed. Information from the timber industry has established that radical changes have occurred over the last 20 years, both in terms of equipment and energy utilisation. The energy efficiency of hardwood drying has improved by 15% since the 1970s, although no significant savings have been realised for softwood. A survey estimating the energy efficiency and operating characteristics of 192 paper dryer sections has been conducted. Drying energy was found to increase to nearly 60% of the total energy used in the early 1980s, but has fallen over the last decade, representing 23% of the total in 1993. These results have demonstrated that effective energy saving measures, such as improved pressing and heat recovery, have been successfully implemented since the 1970s. Artificial neural networks have successfully been applied to model process characteristics of microwave and convective drying of paper coated gypsum cove. Parameters modelled have included product moisture loss, core gypsum temperature and quality factors relating to paper burning and bubbling defects. Evaluation of thermal and dielectric properties have highlighted gypsum's heat sensitive characteristics in convective and electromagnetic regimes. Modelling experimental data has shown that the networks were capable of simulating drying process characteristics to a high degree of accuracy. Product weight and temperature were predicted to within 0.5% and 5C of the target data respectively. Furthermore, it was demonstrated that the underlying properties of the data could be predicted through a high level of input noise.

The formulation of artificial reference standards for use within the ELISPOT assay

Whether to assess the functionality of equipment or as a determinate for the accuracy of assays, reference standards are essential for the purposes of standardisation and validation. The ELISPOT assay, developed over thirty years ago, has emerged as a leading immunological assay in the development of novel vaccines for the assessment of efficacy. However, with its widespread use, there is a growing demand for a greater level of standardisation across different laboratories. One of the major difficulties in achieving this goal has been the lack of definitive reference standards. This is partly due to the ex vivo nature of the assay, which relies on cells being placed directly into the wells. Thus, the aim of this thesis was to produce an artificial reference standard using liposomes, for use within the assay. Liposomes are spherical bilayer vesicles with an enclosed aqueous compartment and therefore are models for biological membranes. Initial work examined pre-design considerations in order to produce an optimal formulation that would closely mimic the action of the cells ordinarily placed on the assay. Recognition of the structural differences between liposomes and cells led to the formulation of liposomes with increased density. This was achieved by using a synthesised cholesterol analogue. By incorporating this cholesterol analogue in liposomes, increased sedimentation rates were observed within the first few hours. The optimal liposome formulation from these studies was composed of 2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC), cholesterol (Chol) and brominated cholesterol (Brchol) at a 16:4:12 µMol ratio, based on a significantly higher (p<0.01) sedimentation (as determined by a percentage transmission of 59 ± 5.9 % compared to the control formulation at 29 ± 12 % after four hours). By considering a range of liposome formulations ‘proof of principle’ for using liposomes as ELISPOT reference standards was shown; recombinant IFN? cytokine was successfully entrapped within vesicles of different lipid compositions, which were able to promote spot formation within the ELISPOT assay. Using optimised liposome formulations composed of phosphatidylcholine with or without cholesterol (16 µMol total lipid) further development was undertaken to produce an optimised, scalable protocol for the production of liposomes as reference standards. A linear increase in spot number by the manipulation of cytokine concentration and/or lipid concentrations was not possible, potentially due to the saturation that occurred within the base of wells. Investigations into storage of the formulations demonstrated the feasibility of freezing and lyophilisation with disaccharide cryoprotectants, but also highlighted the need for further protocol optimisation to achieve a robust reference standard upon storage. Finally, the transfer of small-scale production to a medium lab-scale batch (40 mL) demonstrated this was feasible within the laboratory using the optimised protocol.

Simulation and Evaluation of High-Voltage Power Systems for Civil Aircraft

A status report of the modelling and simulation work that is being undertaken as part of the TIMES (Totally Integrated More Electric Systems) project is presented. Dynamic power quality simulations have been used to asses the performance of the electrical system of a EMA based actuation system for an Airbus A330 size aircraft, for both low voltage 115 V, and high voltage 230 V three-phase AC systems. The high voltage system is shown to have benefits in terms of power quality and reduced size and weight of equipment.

Small-signal input admittance characteristics of a brushless DC motor drive

To carry out stability studies on more electric systems in which there is a preponderance of motor drive equipment, input admittance expressions are required for the individual pieces of equipment. In this paper the techniques of averaging and small-signal linearisation will be used to derive a simple input admittance model for a low voltage, trapezoidal back EMF, brushless, DC motor drive system.

Assessing the effectiveness of five-year mechanical engineering technology programs of junior colleges in Taiwan, R.O.C.: An application of the CIPP evaluation model

The purpose of this study was to evaluate the mechanical engineering technology curriculum effectiveness at the junior college in Taiwan by using the CIPP evaluation model. The study concerned the areas of the curriculum, curriculum materials, individualized instruction, support services, teaching effectiveness, student achievement, and job performance. A descriptive survey method was used with questionnaires for data collection from faculty, students, graduates, and employers.^ All categories of respondents tended to agree that the curriculum provides appropriate occupational knowledge and skills. Students, graduates, and faculty tended to be satisfied with the curriculum; faculty tended to be satisfied with student achievement; graduates tended to be satisfied with their job preparation; and employers were most satisfied with graduates' job performance.^ Conclusions were drawn in the context, input, process, and product of the CIPP model. In Context area: Students were dissatisfied with curriculum flexibility in students characteristics. Graduates were dissatisfied with curriculum design for student's adaptability in new economic and industrial conditions; practicum flexibility in student characteristics; and course overlap. Both students and graduates were dissatisfied with practicum credit hours. Both faculty and students were dissatisfied with the number of required courses.^ In Input area: Students, faculty, and graduates perceived audiovisuals and manipulative aids positively. Faculty and students perceive CAI implementation positively. Students perceived textbooks negatively.^ In Process area: Faculty, students, and graduates perceived all support service negatively. Faculty tended to perceive the ratios of graduates who enter advanced study and related occupation, and who passed the professional skills certification, negatively. Students tended to perceive teaching effectiveness in terms of instructional strategies, the quality of instruction, overall suitability, and receivable, negatively. Graduates also tended to identify the instructional strategies as a negative perception. Faculty and students perceived curriculum objectives and practicum negatively. Both faculty and students felt that instructors should be more interested in making the courses a useful learning experience.^ In Product area: Employers were satisfied with graduates' academic preparation and job performance, adaptability, punctuality, and their ability to communicate, cooperate, and meet organization needs. Graduates were weak in terms of equipment familiarity and supervisory ability.^ In sum, the curriculum of the five-year mechanical engineering technology programs of junior college in Taiwan has served adequately up to this time in preparing a work force to enter industry. It is now time to look toward the future and adapt the curriculum and instruction for the future needs of this high-tech society. ^

A model for continuous measurement of drilled shaft diameter during construction

Non-Destructive Testing (NDT) of deep foundations has become an integral part of the industry's standard manufacturing processes. It is not unusual for the evaluation of the integrity of the concrete to include the measurement of ultrasonic wave speeds. Numerous methods have been proposed that use the propagation speed of ultrasonic waves to check the integrity of concrete for drilled shaft foundations. All such methods evaluate the integrity of the concrete inside the cage and between the access tubes. The integrity of the concrete outside the cage remains to be considered to determine the location of the border between the concrete and the soil in order to obtain the diameter of the drilled shaft. It is also economic to devise a methodology to obtain the diameter of the drilled shaft using the Cross-Hole Sonic Logging system (CSL). Performing such a methodology using the CSL and following the CSL tests is performed and used to check the integrity of the inside concrete, thus allowing the determination of the drilled shaft diameter without having to set up another NDT device.^ This proposed new method is based on the installation of galvanized tubes outside the shaft across from each inside tube, and performing the CSL test between the inside and outside tubes. From the performed experimental work a model is developed to evaluate the relationship between the thickness of concrete and the ultrasonic wave properties using signal processing. The experimental results show that there is a direct correlation between concrete thicknesses outside the cage and maximum amplitude of the received signal obtained from frequency domain data. This study demonstrates how this new method to measuring the diameter of drilled shafts during construction using a NDT method overcomes the limitations of currently-used methods. ^ In the other part of study, a new method is proposed to visualize and quantify the extent and location of the defects. It is based on a color change in the frequency amplitude of the signal recorded by the receiver probe in the location of defects and it is called Frequency Tomography Analysis (FTA). Time-domain data is transferred to frequency-domain data of the signals propagated between tubes using Fast Fourier Transform (FFT). Then, distribution of the FTA will be evaluated. This method is employed after CSL has determined the high probability of an anomaly in a given area and is applied to improve location accuracy and to further characterize the feature. The technique has a very good resolution and clarifies the exact depth location of any void or defect through the length of the drilled shaft for the voids inside the cage. ^ The last part of study also evaluates the effect of voids inside and outside the reinforcement cage and corrosion in the longitudinal bars on the strength and axial load capacity of drilled shafts. The objective is to quantify the extent of loss in axial strength and stiffness of drilled shafts due to presence of different types of symmetric voids and corrosion throughout their lengths.^

Altered Landscape or Arms Race? Making Sense of Military Spending in South America

In 2009, South American military spending reached a total of $51.8 billion, a fifty percent increased from 2000 expenditures. The five-year moving average of arms transfers to South America was 150 percent higher from 2005 to 2009 than figures for 2000 to 2004.[1] These figures and others have led some observers to conclude that Latin America is engaged in an arms race. Other reasons, however, account for Latin America’s large military expenditure. Among them: Several countries have undertaken long-prolonged modernization efforts, recently made possible by six years of consistent regional growth.[2] A generational shift is at hand. Armed Forces are beginning to shed the stigma and association with past dictatorial regimes.[3] Countries are pursuing specific individual strategies, rather than reacting to purchases made by neighbors. For example, Brazil wants to attain greater control of its Amazon rainforests and offshore territories, Colombia’s spending demonstrates a response to internal threats, and Chile is continuing a modernization process begun in the 1990s.[4] Concerns remain, however: Venezuela continues to demonstrate poor democratic governance and a lack of transparency; neighbor-state relations between Colombia and Venezuela, Peru and Chile, and Bolivia and Paraguay, must all continue to be monitored; and Brazil’s military purchases, although legitimate, will likely result in a large accumulation of equipment.[5] These concerns can be best addressed by strengthening and garnering greater participation in transparent procurement mechanism.[6] The United States can do its part by supporting Latin American efforts to embrace the transparency process. _________________ [1] Bromley, Mark, “An Arms Race in Our Hemisphere? Discussing the Trends and Implications of Military Expenditures in South America,” Brookings Institution Conference, Washington, D.C., June 3rd, 2010, Transcript Pgs. 12,13, and 16 [2] Robledo, Marcos, “The Rearmament Debate: A Chilean Perspective,” Power Point presentation, slide 18, 2010 Western Hemisphere Security Colloquium, Miami, Florida, May 25th-26th, 2010 [3] Yopo, Boris, “¿Carrera Armamentista en la Regiόn?” La Tercera, November 2nd, 2009, http://www.latercera.com/contenido/895_197084_9.shtml, accessed October 8th, 2010 [4] Walser, Ray, “An Arms Race in Our Hemisphere? Discussing the Trends and Implications of Military Expenditures in South America,” Brookings Institution Conference, Washington, D.C., June 3rd, 2010, Transcript Pgs. 49,50,53 and 54 [5] Ibid., Guevara, Iñigo, Pg. 22 [6] Ibid., Bromley, Mark, Pgs. 18 and 19

Emergence and Fate of Siloxanes in Waste Streams: Release Mechanisms, Partitioning and Persistence in Three Environmental Compartments

Siloxanes are widely used in personal care and industrial products due to their low surface tension, thermal stability, antimicrobial and hydrophobic properties, among other characteristics. Volatile methyl siloxanes (VMS) have been detected both in landfill gas and biogas from anaerobic digesters at wastewater treatment plants. As a result, they are released to gas phase during waste decomposition and wastewater treatment. During transformation processes of digester or landfill gas to energy, siloxanes are converted to silicon oxides, leaving abrasive deposits on engine components. These deposits cause increased maintenance costs and in some cases complete engine overhauls become necessary. The objectives of this study were to compare the VMS types and levels present in biogas generated in the anaerobic digesters and landfills and evaluate the energetics of siloxane transformations under anaerobic conditions. Siloxane emissions, resulting from disposal of silicone-based materials, are expected to increase by 29% within the next 10 years. Estimated concentrations and the risk factors of exposure to siloxanes were evaluated based on the initial concentrations, partitioning characteristics and persistence. It was determined that D4 has the highest risk factor associated to bioaccumulation in liquid and solid phase, whereas D5 was highest in gas phase. Additionally, as siloxanes are combusted, the particle size range causes them to be potentially hazardous to human health. When inhaled, they may affix onto the alveoli of the lungs and may lead to development of silicosis. Siloxane-based COD-loading was evaluated and determined to be an insignificant factor concerning COD limits in wastewater. Removal of siloxane compounds is recommended prior to land application of biosolids or combustion of biogas. A comparison of estimated costs was made between maintenance practices for removal of siloxane deposits and installation/operation of fixed-bed carbon absorption systems. In the majority of cases, the installation of fixed-bed adsorption systems would not be a feasible option for the sole purpose of siloxane removal. However they may be utilized to remove additional compounds simultaneously.

Situações geográficas em movimento nas praias da área de proteção ambiental de Jenipabu: das ideologias ambientais ao território usado pelo circuito inferior do turismo

The Área de Proteção Ambiental de Jenipabu was created by Decreto 12,620/95, covering the beaches of Redinha Nova, Santa Rita and Jenipabu and Campina communities in the municipality of Extremoz, and Africa community fragment, in Natal. This protected area was created in the context of expansion of tourism in Rio Grande do Norte, in the 1990s, in which PRODETUR investments made possible the installation of infrastructure equipment, mainly in the Via Costeira and Ponta Negra beach in Natal by inserting it in the sun and sea tourism route to Northeast Brazil. In this context the beach Jenipabu in Extremoz, became one of the main attractions for those visiting Natal, due to the natural elements of its landscape, its dune field, which is offered to tourists the buggy ride. In December 1994 the excess buggy rides held in these dunes led to IBAMA ban their access to buggy for carrying out environmental study. This measure resulted in the creation of APAJ in 1995 with the goal of ordering the use and occupation to protect its ecosystems, especially the dunes, the disordered tourism. Given this context, this work aims to analyze the process of creating the APAJ and changes in the geographic space of its beaches, Redinha Nova, Santa Rita and Jenipabu, from the materialization of tourism process, as well as their implications for its residents. To this end, this paper presents a discussion of environmental currents that developed in the western portion of the globe, focusing on the need to regulate small areas of the national territory in protected areas, and an analysis of public policies that enabled the implementation tourism in APAJ as well as the laws and decrees governing the process of creation and management. Using the theory of circuits of urban economy of the Santos (2008) to analyze the territory used by tourism on the beaches of Redinha Nova, Santa Rita and Jenipabu, showing their dependent relationship with the territory used by the upper circuit on the Via Costeira and in the Ponta Negra beach and its influence on the APAJ urbanization process. Ending with the analysis of the influence of the materialization of tourism in the transformation of stocks ways of being-in-space and space-be of the Santa Rita and Jenipabu beaches in each geographical situation of APAJ among the first decades of the twentieth century to the 2014. Fieldwork was conducted between 2012 and 2014, performing actions of qualitative interviews with older residents of Santa Rita and Jenipabu beaches, interviews with structured questionnaire with merchants of APAJ and collecting GPS points trades, identifying and mapping the territory used by the lower circuit in APAJ beaches.

The development of novel chiral tethers for controlling intramolecular aryl-aryl coupling and their application in the synthesis of gomisin M1 and analogues

The primary focus of this thesis was the development of a novel chiral tether that could be used to control axial chirality around a newly formed aryl-aryl bond, and the extension of this methodology to the model synthesis of gomisin M1. In chapter 1, a review detailing the use of chiral tethers in the synthesis of atropisomers is discussed. The use of a variety of chiral molecules including 1,2-diols, 1,3-diols and other diol-based tethers, as well as amine-based and miscellaneous tethers are detailed. In chapter 2, the rationale behind the design of our novel molecular tethers, along with the subsequent synthesis of three chiral 1,3-diol-based tethers, is outlined. The method by which the enantiopurity of these diols was determined is also reviewed. This chapter also includes the attempted Mitsunobu and intramolecular couplings in the model synthesis of BINOL. Chapter 3 discusses the synthesis of suitable aryl halide substrates, and their employment in the attempted tether-controlled asymmetric model synthesis of gomisin M1. A comprehensive investigation into the attempted intramolecular biaryl coupling of these tethered substrates is also included. The non-stereoselective model synthesis of gomisin M1 is outlined in chapter 4. The installation of the desired biaryl linkage and the subsequent attempted intramolecular McMurry couplings are discussed. The impact of different protecting groups in the molecule on the intramolecular McMurry reaction is also outlined. Chapter 5 details the full experimental procedures, including spectroscopic and analytical data for the compounds prepared during this research.

Mineralogical (bulk rock and clay fraction) and stable isotope composition (d13C, d18O) of Aptian deposits of the Bir Oum Ali succession, central Tunisia

Alternations between siliciclastic, carbonate and evaporitic sedimentary systems, as recorded in the Aptian mixed succession of southern Tunisia, reflect profound palaeoceanographic and palaeoclimatic changes in this area of the southern Tethyan margin. The evolution from Urgonian-type carbonates (Berrani Formation, lower Aptian) at the base of the series, to intervals dominated by gypsum or detrital deposits in the remainder of the Aptian is thought to result from the interplay between climate change and tectonic activity that affected North Africa. Based on the evolution of clay mineral assemblages, the early Aptian is interpreted as having been dominated by slightly humid conditions, since smectitic minerals are observed. Near the early to late Aptian boundary, the onset of a gypsiferous sedimentation is associated with the appearance of palygorskite and sepiolite, which supports the installation of arid conditions in this area of the southern Tethyan margin. The evaporitic sedimentation may have also been promoted by the peculiar tectonic setting of the Bir Oum Ali area during the Aptian, where local subsidence may have been tectonically enhanced linked to the opening of northern and central Atlantic. Stress associated with the west and central African rift systems may have triggered the development of NW-SE, hemi-graben structures. Uplifted areas may have constituted potential new sources for clastic material that has been subsequently deposited during the late Aptian. Chemostratigraphic (d13C) correlation of the Bir Oum Ali succession with other peri-Tethyan regions complements biostratigraphic findings, and indicates that a potential expression of the Oceanic Anoxic Event (OAE) 1a may be preserved in this area of Tunisia. Although the characteristic negative spike at the base of this event is not recognized in the present study, a subsequent, large positive excursion with d13C values is of similar amplitude and absolute values to that reported from other peri-Tethyan regions, thus supporting the identification of isotopic segments C4-C7 of the OAE1a. The absence of the negative spike may be linked to either non preservation or non deposition: the OAE1a occurred in a global transgressive context, and since the Bir Oum Ali region was located in the innermost part of the southern Tethyan margin during most of the Aptian, stratigraphic hiatuses may have been longer than in other regions of the Tethys. This emphasizes the importance of integrating several stratigraphic disciplines (bio-, chemo- and sequence stratigraphy) when performing long-distance correlation.

In-situ formation of solidified hydrogen thin-membrane targets using a pulse tube cryocooler

An account is given of the Central Laser Facility's work to produce a cryogenic hydrogen targetry system using a pulse tube cryocooler. Due to the increasing demand for low Z thin laser targets, CLF (in collaboration with TUD) have been developing a system which allows the production of solid hydrogen membranes by engineering a design which can achieve this remotely; enabling the gas injection, condensation and solidification of hydrogen without compromising the vacuum of the target chamber. A dynamic sealing mechanism was integrated which allows targets to be grown and then remotely exposed to open vacuum for laser interaction. Further research was conducted on the survivability of the cryogenic targets which concluded that a warm gas effect causes temperature spiking when exposing the solidified hydrogen to the outer vacuum. This effect was shown to be mitigated by improving the pumping capacity of the environment and reducing the minimum temperature obtainable on the target mount. This was achieved by developing a two-stage radiation shield encased with superinsulating blanketing; reducing the base temperature from 14 0.5 K to 7.2 0.2 K about the coldhead as well as improving temperature control stability following the installation of a high-performance temperature controller and sensor apparatus. The system was delivered experimentally and in July 2014 the first laser shots were taken upon hydrogen targets in the Vulcan TAP facility.

Sustainable solutions for the construction sector: integration of secondary raw materials in the production cycle of concrete

The construction industry is one of the largest consumers of raw materials and energy and one of the highest contributor to green-houses gases emissions. In order to become more sustainable it needs to reduce the use of both raw materials and energy, thus lim-iting its environmental impact. Developing novel technologies to integrate secondary raw materials (i.e. lightweight recycled aggre-gates and alkali activated “cementless” binders - geopolymers) in the production cycle of concrete is an all-inclusive solution to im-prove both sustainability and cost-efficiency of construction industry. SUS-CON “SUStainable, Innovative and Energy-Efficiency CONcrete, based on the integration of all-waste materials” is an European project (duration 2012-2015), which aim was the inte-gration of secondary raw materials in the production cycle of concrete, thus resulting in innovative, sustainable and cost-effective building solutions. This paper presents the main outcomes related to the successful scaling-up of SUS-CON concrete solutions in traditional production plants. Two European industrial concrete producers have been involved, to design and produce both pre-cast components (blocks and panels) and ready-mixed concrete. Recycled polyurethane foams and mixed plastics were used as aggre-gates, PFA (Pulverized Fuel Ash, a by-product of coal fuelled power plants) and GGBS (Ground Granulated Blast furnace Slag, a by-product of iron and steel industries) as binders. Eventually, the installation of SUS-CON concrete solutions on real buildings has been demonstrated, with the construction of three mock-ups located in Europe (Spain, Turkey and Romania)

Medidas de eficiência energética numa indústria cerâmica

O presente relatório resulta de um estágio realizado no âmbito da eficiência energética assente no programa Galp 20-20-20 que tem por génese uma parceria entre a Universidade de Aveiro e a empresa de coberturas cerâmicas, CS – Coelho da Silva S.A. A Fábrica alvo de estudo é uma consumidora intensiva de energia, despendeu no ano de 2013 cerca de 3.768 tep. Devido aos seus processos de cozedura e secagem, apresenta uma elevada dependência de Gás Natural, representando pouco mais de 78% do consumo global da fábrica. Deste consumo de energia térmica, 83% respeita ao forno e os restantes 17% encontram-se alocados ao secador, pelo que as medidas de eficiência energética presentes neste relatório centram-se da redução deste vetor energético. São então propostas três medidas para a redução da dependência deste vetor. A primeira, incide na recuperação de calor residual presente nos gases de exaustão através da instalação de um permutador de calor. Esta medida permite uma redução do consumo na ordem dos 10% e conta com um payback de 2,3 anos resultante de uma economia anual de 150.000 €. Para este estudo foi desenvolvido um modelo dinâmico em excel que permite a simulação de diversos cenários. São também propostas mais duas intervenções que incidem na alteração do circuito térmico. Estas medidas têm um impacte mais reduzido no que respeita ao percentual de redução energético, ambas com menos de 1% de redução do consumo global da fábrica. Contudo são medidas bastante interessantes dada a sua simplicidade e contam com poupanças anuais na ordem dos 6.000 € que resultam num payback inferior a 2 meses. Paralelamente executaram-se dois estudos para a iluminação, o primeiro sugere a instalação de um modelador de tensão que reduz a potência de iluminação em 36%, implicando uma redução da iluminância de cerca de 5%. A redução da potência resulta numa economia energética na ordem dos 0,4% da energia global da instalação. Este equipamento poderá ser adquirido por completo ou em renting. Ao optar pela compra integral, o investimento será apenas ressarcido em 2,8 anos resultante de uma poupança anula de perto de 6.500 €. Caso seja por renting este não tem qualquer custo adicional e as economias monetárias são partilhadas entre a empresa que fornece o equipamento e a CS-Coelho da Silva, S.A. Por fim é sugerida a substituição de parte da iluminação atual da fábrica por tecnologia LED, com esta medida reduz-se o consumo global em 0,76%. Esta medida gera uma economia monetária na ordem dos 11.500 € sendo ressarcida em 2,1 anos.