Drying peanut seed using air ambient temperature at low relative humidity

The moisture content of peanut kernel (Arachis hypogaea L.) at digging ranges from 30 to 50% on a wet basis (w.b.). The seed moisture content must be reduced to 10.5% or below before seeds can be graded and marketed. After digging, peanuts are cured on a window sill for two to five days then mechanically separated from the vine. Heated air is used to further dry the peanuts from approximately 18 to 10% moisture content w.b. Drying is required to maintain peanut seed and grain quality. Traditional dryers pass a high temperature and high humidity air stream through the seed mass. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the kernels. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is heated and passed through the seed. A study was conducted to evaluate the performance of the HPT system in drying peanut seed. The seeds inside the shells were dried from 17.4 to 7.3% in 14 hours and 11 minutes, with a rate of moisture removal of 0.71% mc per hour. This drying process caused no reduction in seed quality as measured by the standard germination, accelerated ageing and field emergence tests. It was concluded that the HPT system is a promising technology for drying peanut seed when efficiency and maintenance of physiological quality are desired.

Incidence of green soybean seeds as a function of environmental stresses during seed maturation

Hot and dry weather conditions during soybean [Glycine max (L.) Merrill] seed maturation can cause forced maturation of the seed, resulting in the production of high levels of green seed, which may be detrimental to seed germination. These stressful conditions were imposed on soybean plants during seed maturation to investigate the production of green seeds and seed quality. Plants of the CD 206 cultivar were grown in a greenhouse until the R5.5 growing stage and then transferred to phytotrons at R6 and R7.2 for stress induction. Plants were subjected to two temperature regimes, high (28ºC to 36ºC) and normal (19ºC to 26ºC), and four soil water availability conditions, control (adequate water supply), 30% gravimetric moisture (GM), 20% GM and no water supply. Seed were harvested at R9. Green seed percentages and 100-seed weights from the lower, middle and upper thirds of each plant were determined. Seed quality was assessed by germination, tetrazolium (viability and vigor) and electrical conductivity tests. Occurrence of green seed varied from 9% to 86%, depending on the severity of the stresses imposed. High temperature, coupled with no water supply at R6, resulted in a pronounced occurrence of green seeds. There was no difference in the percentage of green seeds among the plant segments. Seed quality was negatively affected by the incidence of green seeds. A procedure for screening soybean genotypes in a phytotron for their tolerance and/or susceptibility to the production of green seeds was developed.

Calculation of the magnetic field penetration depth for high-Tc cuprate superconductors based on the Interlayer Pair Tunneling model /

In this work, the magnetic field penetration depth for high-Tc cuprate superconductors is calculated using a recent Interlayer Pair Tunneling (ILPT) model proposed by Chakravarty, Sudb0, Anderson, and Strong [1] to explain high temperature superconductivity. This model involves a "hopping" of Cooper pairs between layers of the unit cell which acts to amplify the pairing mechanism within the planes themselves. Recent work has shown that this model can account reasonably well for the isotope effect and the dependence of Tc on nonmagnetic in-plane impurities [2] , as well as the Knight shift curves [3] and the presence of a magnetic peak in the neutron scattering intensity [4]. In the latter case, Yin et al. emphasize that the pair tunneling must be the dominant pairing mechanism in the high-Tc cuprates in order to capture the features found in experiments. The goal of this work is to determine whether or not the ILPT model can account for the experimental observations of the magnetic field penetration depth in YBa2Cu307_a7. Calculations are performed in the weak and strong coupling limits, and the efi"ects of both small and large strengths of interlayer pair tunneling are investigated. Furthermore, as a follow up to the penetration depth calculations, both the neutron scattering intensity and the Knight shift are calculated within the ILPT formalism. The aim is to determine if the ILPT model can yield results consistent with experiments performed for these properties. The results for all three thermodynamic properties considered are not consistent with the notion that the interlayer pair tunneling must be the dominate pairing mechanism in these high-Tc cuprate superconductors. Instead, it is found that reasonable agreement with experiments is obtained for small strengths of pair tunneling, and that large pair tunneling yields results which do not resemble those of the experiments.

Composition analysis of high-Tc superconducting thin films by quantitative x-ray fluorescence

A method is presented for determining the composition of thin films containing the elements Bi, Sr, Br, Cu, and Ca. Quantitative x-ray fluorescence (XRF) consisting of radioactive sources (secondary foil excitor 241Am-Mo source and 55Pe source), a Si(Li) detector, and a multichannel analyzer were employed. The XRF system was calibrated by using sol gel thin films of known element composition and also by sputtered thin films analyzed by the conventional Rutherford Back Scattering (RBS). The XRF system has been used to assist and optimize the sputter target composition required to produce high-Tc BiSrCaCuO films with the desired metal composition.

Short Isora Fibre Reinforced Natural Rubber Composites

The present study deals with the short isora fibre reinforced natural rubber composites. In recent years there has been a tremendous advancement in the field of science and technology of short fibre reinforced polymer composites. The low density, high strength, high stiffness to weight ratio, excellent durability and design flexibility are the primary reasons for their use in many diversified fields such as air crafts, automobiles, marine industry etc. Compared to the various natural and synthetic fibres used as reinforcement for elastomer composites isora fibre is superior in many aspects. `Isora' is a natural lignocellulosic fibre which is easily available in South India especially in Kerala. The fibre is separated from the bark of the Helicteres isora plant by retting process. This fibre has excellent mechanical properties and is easily amenable to physical and chemical modifications. The study shows that composites with poor interfacial bonding tend to dissipate more energy than that with to interfacial bonding. The mechanical loss also can be related to interfacial bonding. The effect of chemical treatment of isora fibre on damping was also studied. Both in the low and high temperature region which indicates that this composite posseses low damping and hence good interfacial bonding characteristics. Hence these composites are better candidates for high damping applications. Composites with longitudinally oriented fibres showed high storage modulus than transversely oriented ones due to the effective stress transfer between fibre and matrix.

Temporal and Spatial Behavior of Electron Density and Temperature in a Laser-Produced Plasma from YBa2Cu3O7

Spectroscopic studies of laser -induced plasma from a high-temperature superconducting material, viz., YBa2Cu3O7 (YBCO), have been carried out. Electron temperature and electron density measurements were made from spectral data. The Stark broad ening of emission lines was used to determine the electron density, and the ratio of line in tensities was exploited for the determination of electron temperature. An initial electron temperature of 2.35 eV and electron density of 2.5 3 1017 cm2 3 were observed. The dependence on electron temperature and density on different experimental parameters such as distance from the target, delay time after the in itiation of the plasm a, and laser irradiance is also discussed in detail. Index Headings: Laser -plasma spectroscopy; Plasma diagnostics; Emission spectroscop y; YBa2Cu3O7.

On the role of acoustic plasmons in high Tc superconductors

The role of acoustic plasmons in the recently discovered high Tc superconductors is discussed. It is shown that the exchange of acoustic plasmons together with the usual phonon exchange between electrons can give rise to a Tc - 100 K.

Studies on High- Tc Superconductors with Inequivalent Conducting Layers

The thesis deals with the study of super conducting properties of layered cuprates within the frame work of a modified Lawrence-Doniach (LD) model. The thesis is organized in seven chapters. Chapter I is a survey of the phenomena and theories of conventional superconductivity which can serve as a springboard for launching the study of the new class of oxide superconductors and it also includes a chronological description of the efforts made to overcome the temperature barrier. Chapter II deals with the structure and properties of the copper oxide superconductors and also the experimental constraints on the theories of high te:::nperature superconductivity. A modified Lawrence-Doniach type of phenomenological model which forms the basis of the presnt study is also discussed. In chapter III~ the temperature dependence of the upper critical field both parallel and perpendicular to the layers is determined and the results are compared with d.c. magnetization measurements on different superconducting compoilllds. The temperature and angular dependence of the lower critical field both parallel and perpendicular to the layers is also discussed. Chapters IV, V and VI deal with thermal fluctuation effects on superconducting properties. Fluctuation specific heat is studied in chapter IV. Paraconductivity both parallel and perpendicular to the layers is discussed in chapter V. Fluctuation diamagnetism is dealt with in chapter VI. Dimensional cross over in the fluctuation regime of all these quantities is also discussed. Chapter VII gives a summary of the results and the conclusions arrived at.

Zur Verbesserung des Ermüdungsverhaltens des austenitischen Stahls X5CrNi18-10 im Temperaturbereich 25-600°C durch mechanische Randschichtverfestigungsverfahren

Die technischen Oberflächen werden oft als Bauteilversagungsorte definiert. Deswegen ist eine optimale Ausnutzung der Werkstoffeigenschaften ohne mechanische Oberflächenbehandlungsverfahren nicht mehr wegzudenken. Mechanische Randschichtoptimierungsverfahren sind vergleichsweise einfach, Kosten sparend und hocheffektiv. Gerade das Festwalzen wird wegen seiner günstigen Auswirkungen wie die exzellente Oberflächengüte, die hohen Druckeigenspannungen sowie die hohe Oberflächenverfestigung zunehmend an Bedeutung gewinnen. Außerdem wird durch das Festwalzen in einigen Legierungen eine nanokristalline Oberflächenschicht gebildet. Diese brillanten Eigenschaften führen nach einer mechanischen Oberflächenbehandlung zur Erhöhung des Werkstoffwiderstandes unter anderem gegen Verschleiß, Spannungsrisskorrosion und insbesondere zur Steigerung der Schwingfestigkeit. Ein etabliertes Beispiel zur Steigerung der Schwingfestigkeit ist das Festwalzen von Achsen und Kurbelwellen. Auch solche komplexen Komponenten wie Turbinenschaufeln werden zur Schwingfestigkeitssteigerung laserschockverfestigt oder festgewalzt. Die Laserschockverfestigung ist ein relativ neues Verfahren auf dem Gebiet der mechanischen Oberflächenbehandlungen, das z.B. bereits in der Flugturbinenindustrie Anwendung fand und zur Schwingfestigkeitsverbesserung beiträgt. Das Verfahrensprinzip besteht darin, dass ein kurzer Laserimpuls auf die zu verfestigende, mit einer Opferschicht versehene Materialoberfläche fokussiert wird. Das Auftreffen des Laserimpulses auf der verwendeten Opferschicht erzeugt ein expandierendes Plasma, welches eine Schockwelle in randnahen Werkstoffbereichen erzeugt, die elastisch-plastische Verformungen bewirkt. Eine konsekutive Wärmebehandlung, Auslagerung nach dem Festwalzen, nutzt den statischen Reckalterungseffekt. Hierdurch werden die Mikrostrukturen stabilisiert. Die Änderung der Mikrostrukturen kann jedoch zu einer beträchtlichen Abnahme der mittels Festwalzen entstandenen Druckeigenspannungen und der Kaltverfestigungsrate führen. Das Festwalzen bei erhöhter Temperatur bietet eine weitere Möglichkeit die Schwingfestigkeit von metallischen Werkstoffen zu verbessern. Die Mikrostruktur wird durch den Effekt der dynamischen Reckalterung stabilisiert. Die Effekte beim Festwalzen bei erhöhten Temperaturen sind ähnlich dem Warmstrahlen. Das Festwalzen erzeugt Oberflächenschichten mit sehr stabilen Kaltverfestigungen und Druckeigenspannungen. Diese Strukturen haben viele Vorteile im Vergleich zu den durch rein mechanische Verfahren erzeugten Strukturen in Bezug auf die Schwingfestigkeit und die Stabilität der Eigenspannungen. Die Aufgabe der vorliegenden Dissertation war es, Verfahren zur Verbesserung der Schwingfestigkeit im Temperaturbereich zwischen Raumtemperatur und 600 °C zu erforschen. Begleitende mikrostrukturelle sowie röntgenographische Untersuchungen sollen zum Verständnis der Ursachen der Verbesserung beitragen. Für diese Arbeit wurde der in der Praxis häufig verwendete Modellwerkstoff X5CrNi18-10 ausgewählt. Als Randschichtverfestigungsverfahren wurden das Festwalzen, eine Kombination der mechanischen und thermischen, thermomechanischen Verfahren auf der Basis des Festwalzens und eine Laserschockverfestigung verwendet.

Efectos fisiológicos de la termorregulación en trabajadores expuestos a altas temperaturas en una Siderúrgica en Colombia.

La exposición a altas temperaturas en ambientes laborales conlleva a cambios fisiológicos que se manifiestan como mecanismos de compensación a la alteración del equilibrio homeostático corporal. El propósito del presente estudio fue determinar los cambios y el comportamiento de variables fisiológicas a través de frecuencia cardiaca, densidad urinaria, temperatura corporal y tasa de sudoración, en dos escenarios con condiciones térmicas ambientales diferentes definidas por la exposición (grupo expuesto y no expuesto). Adicional, en dos áreas de trabajo diferentes correspondientes al proceso de fundición del acero, una de ellas, Horno electrico donde se hace la fusión de la chatarra y demás materias primas, obteniendo así el acero liquido, el cual se vuelca en el Horno Cuchara y en este, libre ya de escoria se realiza el afino y ajuste definitivo de la composición química del acero. Objetivos: Identificar la relación de las respuestas fisiológicas a carga física y térmica, comparar las respuestas funcionales registradas en el grupo expuestos y no expuestos y contribuir a la introducción de nuevos indicadores para evaluar carga e intensidad de trabajo con fines de normalización ergonómica. Método: Investigación experimental en una muestra de 30 trabajadores evaluados en dos condiciones ambientales diferentes. La temperatura oral se registró al inicio de la jornada y con intervalos de toma de 3 horas. La frecuencia cardiaca (HR) se registró durante las 8 horas de trabajo continuas con pulsometría. Igualmente, se estimó la sudoración por pérdida de masa corporal entre el inicio y el final de la jornada laboral teniendo en cuenta ingestas y perdidas. El procesamiento estadístico se realizó con el programa SPSS v. 20.0, calculándose medidas de tendencia central y dispersión, prueba de wilconxon para las variables dependientes y correlación para identificar asociaciones. Para todos los cálculos se asumió p <0,05. Resultados: No se observaron diferencias significativas frente a la variación de la frecuencia cardiaca (media y máxima), la tasa de sudoración y la densidad urinaria. A pesar de que no hubo diferencias significativas en la variación de la temperatura corporal en horno cuchara, si se observó una diferencia significativa en el horno eléctrico Conclusión: Aunque no se encontraron diferencias estadísticamente significativas en la mayoría de las variables, es un hecho que la exposición a temperaturas elevadas extremas tiene un impacto en el comportamiento fisiológico del organismo. Futuros estudios deben considerar la posibilidad de estandarizar protocolos que permitan la exposición térmica basada en el perfil particular de cada trabajador.

Les sHsps en surera: capacitat protectora enfront l'estrés i variabilitat genètica

Els organismes responen a la temperatura i a molts altres estressos sintetitzant un grup de proteïnes anomenat proteïnes de xoc de calor (HSPs). En plantes les sHsps, d'entre 15 i 30 kDa formen el grup més abundant i divers, classificat en funció de la seva localització subcel.lular i homologia en: mitocondrials, cloroplàstiques, de reticle endoplasmàtic i citoplàsmiques de classe I i II. Les sHsps-CI s'ha descrit que s'indueixen per estrès tèrmic, hídric i oxidatiu (peròxid d'hidrògen, llum UV, ozó) i en resposta a algunes hormones. També s'expressen durant el desenvolupament, per exemple durant l'embriogènesi, on es creu que podrien tenir un paper protector de l'embrió enfront la dessecació. Tot i que hi ha abundants treballs que correlacionen la resistència a l'estrès i l'acumulació de sHsps-CI, els mecanismes moleculars d'aquesta activitat són poc conguts. Tot i això, per diverses sHsps-CI ha estat descrita una activitat xaperona in vitro i, més recentment, que la seva sobreexpressió augmenta la viabilitat de cèl.lules d'E.coli en condicions d'estrès tèrmic. L'estudi de l'acumulació de sHsps-CI en surera (Quercus suber) mitjançant immunodetecció en electroforesi bidimensional mostra uns patrons d'acumulació complexos i formats per dos grups d'espècies proteiques principals, a l'entorn dels 10 i 17 kDa respectivament, que mostren una inducció diferencial en funció del teixit i l'estrès. Mentre que les espècies proteiques de 17 kDa s'indueixen per temperatura però no per estrès oxidatiu, les de ca. 10 kDa ho fan per estrès oxidatiu i no per temperatura. Ambdós grups d'espècies proteiques s'acumulen conjuntament en fel.lema. Assajos de PCR i RT-PCR han permès clonar parcialment tres noves sHsps-CI en surera: Qshsp10-CI, QshspC-CI i QshspD-CI. Aquest fet confirma la multigeneïcitat de les sHsps-CI en surera que apuntava el patró bidimensional. Dels nous clons obtinguts destaca especialment Qshsp10-CI, un gen que presenta un codó stop enmig del domini -cristal.lí que fa que a la proteïna que se'n dedueix li manqui un 55% del domini -cristal.lí i tota l'extensió C-terminal. Es tractaria de la sHsp més petita i més truncada descrita fins al moment. L'anàlisi de l'expressió de Qshsp10-CI mitjançant RT-PCR mostra expressió en plantes tractades amb H2O2 però no en les que han estat sotmeses a un xoc de calor. Aprofitant l'oportunitat que oferia aquesta sHsp-CI de ser utilitzada com a model per l'estudi de la importància del domini -cristal.lí i l'extensió C-terminal en l'activitat protectora enfront l'estrès, es va voler determinar la capacitat que tenia d'augmentar la viabilitat de cèl.lules d'E. coli en condicions d'estrès tèrmic i oxidatiu. Els resultats mostren que la proteïna recombinant QsHsp10-CI, tot i la important truncació que té, és capaç de protegir cèl.lules d'E. coli en condicions d'estrès tèrmic i, remarcablement, en condicions d'estrès oxidatiu. Tots aquests resultats indiquen que les espècies proteiques de ca. 10 kDa podrien correspondre a Qshsp10-CI i tenir un paper en les cèl.lules del fel.lema en la protecció enfront l'estrès oxidatiu. L'estrès oxidatiu provoca lesions al DNA que poden produir errors en la replicació, transcripció o traducció i generar proteïnes aberrants. Donades les condicions d'estrès oxidatiu a les quals es troben sotmeses les cèl.lules del fel.lema, s'ha volgut estudiar la variabilitat dels seus àcids nucleics. La determinació de la taxa de mutació de la regió codificant del gen Qshsp17.4-CI en mRNA i DNA de fel.lema i àpex radicular, un teixit jove i en creixement actiu va mostrar unes taxes sorprenentment elevades en l'mRNA (1/1784 pb) i el DNA genòmic (1/1520 pb) del fel.lema. Aquestes taxes són les més altes descrites en un genoma nuclear eucariota i són similars a les dels virus d'RNA d'evolució ràpida com el virus de l'Hepatitis C. Amb aquestes taxes de mutació, un terç dels mRNAs del fel.lema de la surera contindrien missatges aberrants i la supervivència de les cel.lules es veuria compromesa. Això implica que el fel.lema hauria de ser considerat com un mosaic de cèl.lules genèticament heterogènies i, per tant, una sola seqüència no defineix en tota la seva amplitud un gen en aquest teixit. No es va detectar cap mutació en àpex de rel. Amb l'objectiu d'aprofundir en el coneixement de les mutacions que es donen en aquests dos teixits i per tal de poder fer una anàlisi qualitativa més completa que permetés especular sobre el seu origen, es va aplicar un mètode de selecció de seqüències mutants en base a la utilització d'enzims de restricció. Les mutacions detectades en fel.lema es corresponen amb les relacionades, en altres sistemes no nuclears (plasmidis, fags i DNA bacterià), amb l'estrès oxidatiu. En conseqüència, l'estrès oxidatiu al qual estan sotmeses les cèl.lules del fel.lema podria ser el causant de l'elevada taxa de mutació detectada. D'acord amb això, el tipus majoritari de productes d'oxidació de les bases del DNA que s'acumulen en brots de plàntules de surera en resposta al peròxid d'hidrògen produeixen el mateix tipus de mutacions detectades en l'mRNA del fel.lema de la surera. La major sensibilitat d'aquest nou mètode ha permès, a més, detectar mutacions en molècules d'mRNA de rel, un teixit en el qual no s'havia trobat cap mutació utilitzant el mètode de clonatge i seqüenciació directa. Tot i això, el tipus de mutacions predominants no estan relacionades amb l'estrès oxidatiu sinó amb erros en la reparació dels àcids nucleics.

Temperature- and Pressure-induced Proton Transfer in the 1:1 Adduct Formed between Squaric Acid and 4,4 '-Bipyridine

We have applied a combination of spectroscopic and diffraction methods to study the adduct formed between squaric acid and bypridine, which has been postulated to exhibit proton transfer associated with a single-crystal to single-crystal phase transition at ca. 450 K. A combination of X-ray single-crystal and very-high flux powder neutron diffraction data confirmed that a proton does transfer from the acid to the base in the high-temperature form. Powder X-ray diffraction measurements demonstrated that the transition was reversible but that a significant kinetic energy barrier must be overcome to revert to the original structure. Computational modeling is consistent with these results. Modeling also revealed that, while the proton transfer event would be strongly discouraged in the gas phase, it occurs in the solid state due to the increase in charge state of the molecular ions and their arrangement inside the lattice. The color change is attributed to a narrowing of the squaric acid to bipyridine charge-transfer energy gap. Finally, evidence for the possible existence of two further phases at high pressure is also presented.

Assessment of the effect of time and temperature on the availability of residual phosphate in a glasshouse study of four soils using the Olsen method

The Olsen method is an indicator of plant-available phosphorus (P). The effect of time and temperature on residual phosphate in soils was measured using the Olsen method in a pot experiment. Four soils were investigated: two from Pakistan and one each from England (calcareous) and Colombia (acidic). Two levels of residual phosphate were developed in each soil after addition of phosphate by incubation at either 10degreesC or 45degreesC. The amount of phosphate added was based on the P maximum of each soil, calculated using the Langmuir equation. Rvegrass was used as the test crop. The pooled data for the four soils incubated at 10degreesC showed good correlation between Olsen P and dry matter yield or P uptake (r(2) = 0.85 and 0.77, respectively), whereas at 45 degreesC, each soil had its own relationship and pooled data did not show correlation of Olsen P with dry matter yield or P uptake. When the data at both temperatures were pooled, Olsen P was a good indicator of yield and uptake for the English soil. For the Pakistani soils, Olsen P after 45 degreesC treatment was an underestimate relative to the 10 degreesC data and for the Colombian soil it was an overestimate. The reasons for these differences need to be explored further before high temperature incubation can be used to simulate long-term changes in the field.