Two-Phase Flow In Anode Flow Field Of A Small Direct Methanol Fuel Cell In Different Gravities

An in-situ visualization of two-phase flow inside anode flow bed of a small liquid fed direct methanol fuel cells in normal and reduced gravity has been conducted in a drop tower. The anode flow bed consists of 11 parallel straight channels. The length, width and depth of single channel, which had rectangular cross section, are 48.0, 2.5 and 2.0 mm, respectively. The rib width was 2.0 mm. The experimental results indicated that when the fuel cell orientation is vertical, two-phase flow pattern in anode channels can evolve from bubbly flow in normal gravity into slug flow in microgravity. The size of bubbles in the reduced gravity is also bigger. In microgravity, the bubbles rising speed in vertical channels is obviously slower than that in normal gravity. When the fuel cell orientation is horizontal, the slug flow in the reduced gravity has almost the same characteristic with that in normal gravity. It implies that the effect of gravity on two-phase flow is small and the bubbles removal is governed by viscous drag. When the gas slugs or gas columns occupy channels, the performance of liquid fed direct methanol fuel cells is failing rapidly. It infers that in long-term microgravity, flow bed and operating condition should be optimized to avoid concentration polarization of fuel cells.

Construction, extension and evaluation of the improved smoking kiln (Banda) in Kainji Lake area

Fish smoking, as a traditional occupation of fishermen and women in Kainji Lake Area (Nigeria) is done using simple traditional ovens called 'Banda', the fuel for the smoking being almost hundred percent dependent on wood. A simple modification was made to the traditional 'Banda' oven using a damper to prevent burning of the fish. A comparison of the improved and the traditional 'Banda' was made. The results indicate that fuel wood consumption was reduced 52 percent by using the improved 'Banda', which implied that 50 percent of fish processor's income could be saved through the adoption of this technology. The most important advantage of the improved kiln, fuel wood conservation, represents for fishers a problem of an economic importance. Whilst they are aware that it is becoming much more difficult to get the needed fuel wood, the children can still conveniently collect enough wood for both home use and processing activities. The cost of the components of the improved kiln, when compared with the traditional version may be considered quite significant, and hence the reluctance of the fish processors in constructing similar ones. Selected blacksmiths were trained to continue the fabrication of the kiln component. The training was carried out to assure that the improved kiln will be constructed even after the project will end to support the fabrication

Hot spot formation outside of the fusion-fuel core

An alternative fast-ignition method is proposed involving the formation of a hot spot outside the precompressed fusion-fuel core by a series of shocks driven directly by the light pressure of laser pulses of increasing intensities. It is shown that a hot spot, which can be of different material from that of the fuel core, with temperature similar to 10 keV and density similar to 200 g/cm(2), can be formed. Being an electrically neutral plasma, the hot spot can easily be sent into the fuel core. (c) 2005 American Institute of Physics.

Cu2O substrates and epitaxial Cu2O/ZnO thin film hetero-structures for solar energy conversion

Future fossil fuel scarcity and environmental degradation have demonstrated the need for renewable, low-carbon sources of energy to power an increasingly industrialized world. Solar energy with its infinite supply makes it an extraordinary resource that should not go unused. However with current materials, adoption is limited by cost and so a paradigm shift must occur to get everyone on the same page embracing solar technology. Cuprous Oxide (Cu2O) is a promising earth abundant material that can be a great alternative to traditional thin-film photovoltaic materials like CIGS, CdTe, etc. We have prepared Cu2O bulk substrates by the thermal oxidation of copper foils as well Cu2O thin films deposited via plasma-assisted Molecular Beam Epitaxy. From preliminary Hall measurements it was determined that Cu2O would need to be doped extrinsically. This was further confirmed by simulations of ZnO/Cu2O heterojunctions. A cyclic interdependence between, defect concentration, minority carrier lifetime, film thickness, and carrier concentration manifests itself a primary reason for why efficiencies greater than 4% has yet to be realized. Our growth methodology for our thin-film heterostructures allow precise control of the number of defects that incorporate into our film during both equilibrium and nonequilibrium growth. We also report process flow/device design/fabrication techniques in order to create a device. A typical device without any optimizations exhibited open-circuit voltages Voc, values in excess 500mV; nearly 18% greater than previous solid state devices.

Fabrication of two-dimensional periodic nanostructures by two-beam interference of femtosecond pulses

Two-dimensional periodic nanostructures on ZnO crystal surface were fabricated by two-beam interference of 790 nm femtosecond laser. The long period is, as usually reported, determined by the interference pattern of two laser beams. Surprisingly, there is another short periodic nanostructures with periods of 220-270 nm embedding in the long periodic structures. We studied the periods, orientation, and the evolution of the short periodic nanostructures, and found them analogous to the self-organized nanostructures induced by single fs laser beam. (C) 2008 Optical Society of America.

Fabrication of microelectrodes deeply embedded in LiNbO3 using a femtosecond laser

We present a novel technique to fabricate deeply embedded microelectrodes in LiNbO3 using femtosecond pulsed laser ablation and selective electroless plating. The fabrication process mainly consists of four steps, which are (1) micromachining of microgrooves on the surface of LiNbO3 by femtosecond laser ablation; (2) formation of AgNO3 films on substrates; (3) scanning the femtosecond laser beam in the fabricated microgrooves for modi. cation of the inner surfaces; and (4) electroless copper plating. The void-free electroless copper plating is obtained with appropriate cross section of microgrooves and uniform initiation of the autocatalytic deposition on the inner surface of grooves. The dimension and shape of the microelectrodes could be accurately controlled by changing the conditions of femtosecond laser ablation, which in turn can control the distribution of electric field inside LiNbO3 crystal for various applications, opening up a new approach to fabricate three-dimensional integrated electro-optic devices. (C) 2008 Elsevier B. V. All rights reserved.