多模光纤激光器实现高功率低阶模输出

采用光纤缠绕的方法，来抑制大模场面积（LMA）双包层光纤激光器中的高阶模振荡。将光纤缠绕至两种不同半径，实验测量了相应条件下激光器的输出功率和光束质量因子M2。缠绕半径为165mm时，输出功率为217W，M2为2.96；缠绕半径为52mm时，输出功率为160W，M2为1.38。光纤激光器相应的斜率效率分别为60％和48％。光纤缠绕半径较小时，虽然激光器输出功率减小，但其亮度是大缠绕半径时对应值的3.4倍。

先进光纤激光技术

高光束质量、高峰值功率、小型化的短脉冲激光系统在激光雷达、光谱学、精密探测等领域有非常广泛的应用。在脉冲光纤激光器方面,针对调Q双包层光纤激光、脉冲调制LD技术及其多级光纤级联放大系统、基于调Q固体激光器的全光纤型MOPA系统进行了详细的理论分析和实验研究,研制出了全光纤化的脉冲光纤激光器。这些工作为全光纤化脉冲光纤激光器的研制和推广奠定了基础。

两微米瓦级掺铥短光纤激光器

以短的高掺杂浓度的掺铥硅基光纤为增益介质，采用790 nm波长的激光二极管(LD)为抽运源，得到了波长为2 μm的高功率激光输出。当光纤长度为7 cm时，激光器的阈值泵浦功率为135 mW，最大输出功率为1.09 W，斜率效率为9.6%(相对于耦合进光纤的抽运功率)。该激光器的输出稳定性在5%以内。此外，我们还观察分析了工作温度和其他腔结构参量对该激光器工作性能的影响。

千瓦级双包层光纤激光器冷却方案设计理论和实验研究

尽管双包层光纤激光器的散热性能好于传统的固体激光器的散热性能,光纤激光器中的热沉积仍然是限制提高其输出功率的重要因素.以双端抽运的400W双包层光纤激光器为实例,定量分析了光纤内的热沉积分布.根据所建立的散热模型,为了确保千瓦级双包层光纤激光器安全稳定的运行,抽运端附近的对流换热系数应大于2.8×10-2W·cm-2K-1.据此设计出高功率双包层光纤激光器抽运端冷却装置并成功应用在激光系统中,获得了千瓦级的激光输出.

侧面泵浦的短矩形掺钕磷酸盐玻璃光纤激光器

利用光纤－波导耦合器技术侧面泵浦一根4厘米长的短光纤，我们研制得到了一个红外波长的光纤激光器。该激光器的增益介质是横截面为矩形的掺钕磷酸盐玻璃光纤，其纤芯横截面尺寸为1.5×0.5 毫米，数值孔径为0.2。单横模激光可以通过该矩形光纤的增益-导引效应来获得。最大的激光输出功率为1.05瓦，斜率效率为10％。

激光多普勒振动计用于水下声光通信

介绍了激光多普勒振动计(LDV)用于水下声光通信的应用背景,阐述了激光多普勒振动计的工作原理和两种相干检测方式。采用零差的相干探测方式,设计并实现了一套光纤结构的激光多普勒振动计。为了证明系统能够应用于水下声光通信,进行了对水下声源发出的声波频率和强度的探测实验。通过对实验数据的分析得出：第一,系统能够检测出水下声源发出的声波频率,对7 kHz附近的10个声波频率的测量标准偏差小于8 Hz; 第二,系统探测信号强度与水下声源发声的声压级成指数关系,对于水下目标通信所用的3.5 kHz和7 kHz声波频段的

氟磷酸盐玻璃的应用研究进展

氟磷酸盐玻璃系统南于其特殊的光学性能和优良的机做与热学性能一直是特种光学玻璃材料领域的一个研究热点。总结了氟磷酸盐玻璃的分类及玻璃组分与其结构的关系，综述了氟磷玻璃在光学器件、高能高功率激光玻璃、光纤激光器、光纤放大器及上转换发光基质材料等领域上的应用，并对其未来的发展进行了展望。

Infrared-to-visible upconversion emissions in Er3+ doped TeO2-based oxyhalide glasses

The fluorescence and up-conversion spectral properties of Er3+-doped TeO2-ZnO and TeO2-ZnO-PbCl2 glasses suitable for developing optical fiber amplifier and laser have been fabricate and characterized. Strong green (around 527-550 nm) and red (around 661 nm) up-conversion emissions under 977 nm laser diode excitation were investigated, corresponding to H-2(11/2), S-4(3/2), --> I-4(15/2) and F-4(9/2) --> I-4(15/2) transitions of Er3+ ions respectively, have been observed and the involved mechanisms have been explained. The dependence of up-converted fluorescence intensity versus laser power confirm that two-photons contribute to up-conversion of the green-red emissions. The novelty of this kind of optical material has been its ability in resisting devitrification, and its promising optical properties strongly encourage for their further development as the rare-earth doped optical fiber amplifiers and upconversion fiber laser systems.

稀土离子掺杂的多组分玻璃光纤

abstract {Rare earth ions doped multi-component glass fibers have important application in broad band fiber amplifier and up-conversion fiber lasers. In this paper, the mechanism and the progress of study on rare earth ions doped multi-component glass fibers in broad band fiber amplifier and up-conversion fiber lasers are introduced and reviewed. The questions and the applications of rare earth ions doped multi-component glass fibers in the future are also prospected. Based on the present research progress, it is suggested to further study the tellurite and bismuth glasses, which are used as fiber materials in broad band fiber amplifier. To up-conversion fiber laser, it is still need to further investigate novel glasses, which has low phonon energy and good physical and chemical properties.}

光子晶体光纤的研究新进展

综述了光子晶体光纤（PCF）不同于传统光纤的各种性质，并详细讨论了光子晶体光纤在通信和光纤激光等领域的新发展。

Efficient frequency upconversion emission in Er3+-doped novel strontium lead bismuth glass

Er3+ -doped strontium lead bismuth glass for developing upconversion lasers has been fabricated and characterized. The Judd-Ofelt intensity parameters Omega(1) (t = 2,4,6), calculated based on the experimental absorption spectrum and Judd-Ofelt theory, were found to be Omega(2) = 2.95 x 10(-20), Omega(4) = 0-91 X 10(-20), and Omega(6) = 0.36 x 10(-20) cm(2). Under 975 nm excitation, intense green and red emissions centered at 525, 546, and 657 nm, corresponding to the transitions H-2(11/2) --> I-4(15/2), S-4(3/2) I-4(15/2), and F-4(9/2) --> I-4(15/2) respectively were observed. The upconversion mechanisms are discussed based oil the energy matching and quadratic dependence on excitation power, and the dominant mechanisms are excited state absorption and energy transfer upconversion for the green and red emissions. The long-lived I-4(11/2) level is supposed to serve as the intermediate state responsible for the upconversion processes. (C) 2004 Published by Elsevier B.V.

Caracterización de láser convencional de fibra en operaciones de texturizado.

[ES]El objetivo de este TFG es comprobar si un láser de fibra convencional diseñado para trabajar en régimen continuo es capaz de llevar a cabo operaciones de texturizado y hasta qué punto. Para ello se realizarán una serie de ensayos en función de varios parámetros de entrada, con los que se obligará al láser a mantener un régimen pulsado, necesario para operaciones de texturizado láser.

在光子晶体光纤中实现波长调谐飞秒孤子脉冲输出

介绍了在光子晶体光纤中产生波长调谐飞秒光孤子脉冲的机理及研究进展，并对波长调谐飞秒孤子激光系统进行了分析和比较。

Solution-phase exfoliation of graphite for ultrafast photonics

We exfoliate graphite in both aqueous and non-aqueous environments through mild sonication followed by centrifugation. The dispersions are enriched with monolayers. We mix them with polymers, followed by slow evaporation to produce optical quality composites. Nonlinear optical measurements show similar to 5% saturable absorption. The composites are then integrated into fiber laser cavities to generate 630 fs pulses at 1.56 mu m. This shows the viability of solution phase processing for graphene based photonic devices. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Micromachining of glassy carbon toolsets for micro embossing applications

Laser micro machining is fast gaining popularity as a method of fabricating micro scale structures. Lasers have been utilised for micro structuring of metals, ceramics and glass composites and with advances in material science, new materials are being developed for micro/nano products used in medical, optical, and chemical industries. Due to its favourable strength to weight ratio and extreme resistance to chemical attack, glassy carbon is a new material that offers many unique properties for micro devices. The laser machining of SIGRADUR® G grade glassy carbon was characterised using a 1065 nm wavelength Ytterbium doped pulsed fiber laser. The laser system has a selection of 25 preset waveforms with optimised peak powers for different pulsing frequencies. The optics provide spot diameter of 40 μm at the focus. The effect of fluence, transverse overlap and pulsing frequency (as waveform) on glassy carbon was investigated. Depth of removal and surface roughness were measured as machining quality indicators. The damage threshold fluence was determined to be 0.29 J/cm2 using a pulsing frequency of 250 kHz and a pulse width of 18 ns (waveform 3). Ablation rates of 17 < V < 300 μm3/pulse were observed within a fluence range of 0.98 < F < 2.98 J/cm2. For the same fluence variation, 0.6 μm to 6.8 μm deep trenches were machined. Trench widths varied from 29 μm at lower fluence to 47 μm at the higher fluence. Square pockets, 1 mm wide, were machined to understand the surface machining or milling. The depth of removal using both waveform 3 and 5 showed positive correlation with fluence, with waveform 5 causing more removal than waveform 3 for the same fluence. Machined depths varied from less than 1 μm to nearly 40 μm. For transverse overlap variation using waveform 3, the best surface finish with Rz = 1.1 μm was obtained for fluence 0.792 J/cm2 for transverse overlap of 1 μm, 6 μm, and 9 μm at machined depths of 22.9 μm, 6.6 μm, and 4.6 μm respectively. For fluence of 1.426 J/cm2, the best surface finish with Rz = 1.2 μm was obtained for transverse overlap of 6 μm, and 9 μm at machined depths of 12.46 μm, and 8.6 μm respectively. The experimental data was compiled as machining charts and utilised for fabricating a micro-embossing glassy carbon master toolsets as a capability demonstration.