Effect of alloying additions on the SFE, Neél temperature and shape memory effect in Fe–Mn–Si-based alloys

A range of Fe–Mn–Si-based shape memory alloys has been investigated to examine the interplay of composition, stacking fault probability (SFP) and Neél temperature on the shape memory effect (SME). It has been found that the SFP (inversely proportional to stacking fault energy) showed little correlation to the SME for the range of alloy compositions examined. Further, the Neél temperature was not found to exhibit a significant effect on the SME. The addition of interstitial elements, however, was found to markedly decrease the SME.

The effect of food temperature on post-prandial metabolism in albatrosses

Heat generated by the specific dynamic action (SDA) associated with feeding is known to substitute for the thermoregulatory costs of cold-exposed endotherms; however, the effectiveness of this depends on food  temperature. When food is cooler than core body temperature, it is warmed by body heat and, consequently, imposes a thermoregulatory challenge to the animal. The degree to which this cost might be `paid' by SDA depends on the relative timing of food heating and the SDA response. We investigated this phenomenon in two genera of endotherms, Diomedea and Thalassarche albatrosses, by measuring postprandial metabolic rate following ingestion of food at body temperature (40°C) and cooler (0 and 20°C). This permitted us to estimate potential contributions to food warming by SDA-derived heat, and to observe the effect of cold food on metabolic rate. For meal sizes that were ~20% of body mass, SDA was 4.22±0.37% of assimilated food energy, and potentially contributed 17.9±1.0% and 13.2±2.2% of the required heating energy of food at 0°C for Diomedea and Thalassarche albatrosses, respectively, and proportionately greater quantities at higher food temperatures. Cold food increased the rate at which postprandial metabolic rate increased to 3.2–4.5 times that associated with food ingested at body temperature. We also found that albatrosses generated heat in excess by more than 50% of the estimated thermostatic heating demand of cold food, a probable consequence of time delays in physiological responses to afferent signals.

The combined effect of light intensity and temperature on the chlorophyll and carotenoid pigments of phytoplankton

Chlorophyll a and other photosynthetic pigments are used as indicators of phytoplankton biomass, composition and physiological state. Extraction and HPLC procedures were developed to analyse for chlorophyll and carotenoid pigments. The effect of the environment on pigment production must be quantified before the pigments can be used to accurately estimate biomass or quantitatively describe phytoplankton composition.

Effect of increased temperature on erosion-corrosion under turbulent conditions in Bayer liquor

A study of the behaviour of mild steel in synthetic Bayer liquor at 25 °C and 95 °C showed that turbulent conditions had a small effect on the anodic currents at 25 °C, but caused large increases in currents at 95 °C. This may be due to the increased solubility of magnetite at the higher temperature.

The effect of humidity and temperature on Wool Comfort Meter assessment of single jersey wool fabrics

The Wool ComfortMeter provides an objective measurement of the fabric-evoked prickle discomfort rating provided by wearers. This work aimed to quantify the sensitivity of the Wool ComfortMeter over a range of different temperature and humidity conditions to determine the recommended test conditions for its operation. The design was: three temperatures (notionally 20, 25 and 30°C) at three relative humidities (RHs, notionally 50, 65 and 80%) each with two replicates, using six different wool single jersey knits (mean fibre diameter 19.5–27.0 µm). As it was difficult to achieve exactly some of the extreme combinations of temperature and RH, some combinations were repeated, providing a total of 23 different assessment conditions. Data were analysed using restricted maximum likelihood mixed model analysis. The best fixed model included RH, RH2, temperature and the interaction of temperature and RH, accounting for 95% of the variation in Wool ComfortMeter readings. Wool ComfortMeter values were almost constant at 55–60% RH. Generally, the Wool ComfortMeter value reduced with increasing RH > 60% at temperatures of 25°C and 28.5°C as the regain of the fabric increased. However, at 20°C little change was detected as RH was increased from 50 to 80% as there were only small changes in fabric regain. The observed effects were in a good agreement with existing knowledge on the effect of regain on the mechanical properties of wool fibre. Wool ComfortMeter is best operated under standard conditions for textile testing of 65% RH and 20°C.

Highly sensitive SnO2 nanofiber chemiresistors with a low optimal operating temperature: synergistic effect of Cu2+/Au co-doping

Metal oxide chemiresistors (MOCs) with a low optimal operating temperature, high sensitivity and fast response/recovery are highly promising for various applications, but remain challenging to realize. Herein, we demonstrate that SnO2 nanofibers after being co-doped with Cu2+ and Au show considerably enhanced sensing performances at an unexpectedly decreased operating temperature. A synergistic effect occurs when the two dopants are introduced together. Co-doping may form a novel strategy to the development of ultrasensitive MOCs working at a low optimal temperature. This journal is © the Partner Organisations 2014.

Effect of alloying and extrusion temperature on the microstructure and mechanical properties of Mg-Zn and Mg-Zn-RE alloys

Extruded Mg-Zn-RE alloys have been shown to exhibit excellent combinations of yield strength and ductility, but it is not completely clear how adding rare earth metals to Mg-Zn alters the microstructure and affects the mechanical properties. Microstructural changes and the resulting mechanical properties from changes in composition and extrusion temperature have been investigated for Mg-. x Zn-. y RE (. x=2.5 and 5. wt.%, y=0 and 1. wt. %, and RE=Gd and Y) alloys. Adding RE to Mg-Zn increased the strength and reduced the ductility, while increasing the zinc concentration in the Mg-Zn-RE alloys had the reverse effect.

Effect of sintering temperature on electrochemical performance of LiFe0·4Mn0·6PO4/C cathode materials

Carbon coated LiFe0·4Mn0·6PO4 (LiFe0·4Mn0·6PO4/C) was synthesised using high energy ball milling and annealing processes. The starting materials of Li2C2O4, FeC2O4.2H2O, MnC2O4.2H2O, NH4H2PO4 were firstly milled for 40 h, and followed by further milling for 5 h after adding glucose solution. The milled sample was heated at different temperatures (550, 600, 650 and 700°C) for 10 h to produce LiFe0·4Mn0·6PO4/C composites. The structure and morphology of the samples were investigated using X-ray diffraction, field emission scanning electron microscopy, and high resolution electron microscopy. The phase of samples annealed at 550 and 600°C mainly consists of olivine type LiFePO4, but a small amount of Fe2P impurity phase is formed in the samples annealed at 650 and 700°C. Electrochemical analysis results show that LiFe0·4Mn0·6PO4/C synthesised at 600°C exhibits the best performance with the initial discharge capacity of 128 mAh g-1 at 0·1 C, and 109 mAh g-1 at 1 C after 500 cycles. The LiFe0·4Mn0·6PO4/C exhibits excellent electrochemical properties for high energy density lithium ion batteries.

The effect of treatment temperature on corrosion resistance and hydrophilicity of an ionic liquid coating for mg-based stents

Mg alloys are attractive candidate materials for biodegradable stents. However, there are few commercially available Mg-based stents in clinical use because Mg alloys generally undergo rapid localized corrosion in the body. In this study, we report a new surface coating for Mg alloy AZ31 based on a low-toxicity ionic liquid (IL), tributyl(methyl)phosphonium diphenyl phosphate (P1,4,4,4 dpp), to control its corrosion rate. Emphasis is placed on the effect of treatment temperature. We showed that enhancing the treatment temperature provided remarkable improvements in the performances of both corrosion resistance and biocompatibility. Increasing treatment temperature resulted in a thicker (although still nanometer scale) and more homogeneous IL film on the surface. Scanning electron microscopy and optical profilometry observations showed that there were many large, deep pits formed on the surface of bare AZ31 after 2 h of immersion in simulated body fluid (SBF). The IL coating (particularly when formed at 100 °C for 1 h) significantly suppressed the formation of these pits on the surface, making corrosion occur more uniformly. The P1,4,4,4 dpp IL film formed at 100 °C was more hydrophilic than the bare AZ31 surface, which was believed to be beneficial for avoiding the deposition of the proteins and cells on the surface and therefore improving the biocompatibility of AZ31 in blood. The interaction mechanism between this IL and AZ31 was also investigated using ATR-FTIR, which showed that both anion and cation of this IL were present in the film, and there was a chemical interaction between dpp(-) anion and the surface of AZ31 during the film formation.