Design, synthesis and characterization of novel nitrogen-and sulfur-containing polymers with well-defined conjugated length

A series of novel nitrogen- and sulfur-containing conjugated polymers with well-defined conjugation length have been synthesized via an acid-induced self-polycondensation of functional monomers with methylsulfinyl groups. Synthesized polymers exhibit good solubility in common solvents, such as CHCl3, THF, DMF, DMSO, and NMP. With increased numbers of aminophenyl groups, these polymers have shown similar electrical properties to polyaniline (PAn), and these are demonstrated by UV-vis spectroscopy and cyclic voltammetry (CV) measurements on the polymers. The conductivity of preliminarily protonic-doped poly[phenylene sulfide-alt-tetrakis(aniline)] (PPSTEA) is up to 10(-1) S cm(-1).

Polymer/silica nanoscale hybrids through sol-gel method involving emulsion polymers. 1. Morphology of poly(butyl methacrylate)/SiO2

In this article, we report on an approach of using an emulsion polymerized polymer in preparing organic-inorganic nanocomposites through a sol-gel technique. By mixing a polymer emulsion with prehydrolyzed tetraethoxysilane transparent poly(butyl methacrylate)/SiO2, nanocomposites were prepared as shown by TEM. AFM, FTIR, and XPS results show that there is a strong interaction between polymer latex particles and the SiO2 network. Comparison of the emulsion method with a traditional solution method shows that nanocomposites can be prepared by both methods, but there is some difference in their morphology and properties.

Two new coordination polymers of Co(II) with 1,1 '-(1,4-butanediyl)bis(benzimidazole)

Two new compounds, [CoL2(H2O)(2)](NO3)(2). 8H(2)O (1) and [CoL(H2O)(2)(CH3CO2)(2)]. H2O (2), were obtained from self-assembly of the corresponding metal salts with 1,1'-(1,4-butanediyl)bis(benzimidazole) (L). In 1, each cobalt ion is coordinated to four nitrogen atoms from four molecules of L, and to two water molecules. Metal ions are bridged by L ligands to form infinite (4, 4) networks that contain 44-membered rings. The (4, 4) networks of 1 stack in a parallel fashion, resulting in the formation of large channels in the material. In 2, each cobalt ion is coordinated to two N atoms from two L molecules, two water molecules and two carboxylate O atoms from two acetate anions. Each L molecule is coordinated to two cobalt ions, acting as a bridging ligand as in 1. The bridged cobalt ions form an infinite zigzag chain structure.

Synthesis and electroluminescent properties of a novel terbium complex

A new carboxylic acid ligand (o-amino-4-hexadecane benzoic acid, AHBA) and a corresponding terbium complex (Tb(AHB)(3)) were synthesized and characterized. A multilayer electroluminescent device with poly(N-vinylcarbazole) (PVK), 2-(4-biphenyl)-5-(4-t-butylphenyl)-1,3,4-oxadiazole (PBD) and the terbium complex as emissive layer was fabricated: glass substrate/ITO/PPV/PVK:-To(AHB)(3):PBD/Alq(3)/Al. The photoluminescence (PL) and electroluminescence (EL) spectra were discussed. This EL cell exhibited characteristic emission of terbium ions with a maximum luminance of 35 cd/m(2) at 20 V. (C) 2000 Elsevier Science S.A. All rights reserved.

Green electroluminescence generated from the thin film based on a soluble lanthanide complex

Electroluminescent (EL) devices based on a soluble complex Tb(MDP)(3) [Tris-(monododecyl phthalate)Terbium] doped with poly (N-vinylcarbazole) (PVK), (2-(4-biphenyl)-5-(4-t-butylphenyl)-1,3,4-oxadiazole) (PBD) were fabricated. The device structures of ITO/PVK/PVK:PBD:Tb(MDp)(2)/Aiq(3)/Al and ITO/PVK:PBD:Tb(MDP)(3)/Alq(3)/Al were employed. The Tb(MDP), as emissive layer was spin-coated. The EL cell exhibited characteristic emission of terbium ion. (C) 2000 Elsevier Science S.A. All rights reserved.

Networks with hexagonal circuits in co-ordination polymers of metal ions (Zn-II, Cd-II) with 1,1 '-(1,4-butanediyl)bis(imidazole)

Three new compounds, [ZnL1.5(H2O)(SO4)]. 6H(2)O 1, [ZnL1.5(H2O)(2)][NO3](2). 2H(2)O 2 and [CdL1.5(H2O)(2)(SO4)]. 4H(2)O 3 were obtained from self-assembly of the corresponding metal salts with 1,1'-(1,4-butanediyl)bis(imidazole) (L). In both 1 and 2 zinc ion is five-co-ordinated, showing a less-common trigonal bipyramidal co-ordination polyhedron, while cadmium ion of 3 is six-co-ordinated with a common octahedral arrangement. The sulfate ions of 1 and 3 are co-ordinated, however the nitrate ions of 2 are not. Each of the three compounds is composed of a (6, 3) network with the hexagonal smallest circuit containing six metal ions and six L; each L is co-ordinated to two metal ions, acting as a bridging ligand. In 1 the 2-D sheet of (6, 3) networks is interpenetrated in an inclined mode by symmetry related, identical sheets to give an interlocked 3-D structure, while the (6, 3) networks of both 2 and 3 stack in a parallel fashion to construct frameworks having channels.

Spontaneous emission properties of organic film in plane optical microcavity

The spontaneous emission properties of a single layer organic film in plane optical microcavities were studied. Optical microcavity was formed by a Tris(8-quinolinolato) aluminium (Alq) film sandwiched between a distributed Bragg reflector (DBR) and a Ag metallic reflector. Two kinds of microcavities were devised by using a different DBR structure. Compared with a Alq film, significantly spectral narrowing and intensity enhancement was observed in the two microcavities, which is attributed to the microcavity effect. The spectra characteristics of the two microcavities showed that the structure of DBR has much influence on the emission properties of a microcavity. (C) 2000 Elsevier Science S.A. All rights reserved.

Electroluminescent properties of the Tris-(acetylsalicylate)-terbium (Tb(AS)(3))

The solubility of [Tris-(acetylsalicylate)-terbium] [Tb(AS)(3)] is improved to a greater extent than [Tris-(salicylate)-terbium] [Tb(Sal)(3)] following introduction of a flexible acetyl group. Th3+ binds with acetylsalicylate in solution at low pH value and the resultant Tb(AS)(3) has good solubility in chloroform. A Green EL device with the structure ITO/PVK/PVB:PBD: Tb(AS)(3)/ PBD/Al has been fabricated based on soluble Tb(AS)(3), in which Tb(AS)(3) was first used as an emissive center doped with PVK and PBD. The hole-transporting layer and the emissive layer were formed by spin coating. The device exhibited a highly pure characteristic green light of Tb3+. (C) 2001 Elsevier Science B.V. All rights reserved.

A comparative study on the electroluminescence properties of some terbium beta-diketonate complexes

By comparing the phosphorescence spectra of Gd(acac)(3) (acac=acetylacetone), Gd(TFacac)3 (TFacac=1,1,1-trifluoroacetylacetone), the effects of fluorine replacement of hydrogen on the triplet state energy of the ligands were revealed. Fluorine can lower the triplet state energy of Hacac and make it more suitable for energy transfer towards the D-5(4) state of terbium. Organic electroluminescent devices (OELDs) with the corresponding trivalent terbium complexes as emissive layers were fabricated. Triple-layer-type devices with a structure of glass substrate/ITO (indium tin oxide)/PVK [poly(N-vinylcarbazole)]/PVK : Tb complex: PBD [2-(4-biphenyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole]/PBD/Al exhibit bright green luminescence upon applying a dc voltage. The luminance of a device with Tb(TFacac)(3)phen (1,10-phenanthroline) and Tb( TFacac) 3 as emissive layer is higher than that of the corresponding devices with Tb(acac)(3)(phen) and Tb(acac)(3) as emissive layers. The EL device with Tb(TFacac)(3)(phen) as emitter exhibits characteristic emission of Tb3+ ions with a maximum luminance of 58 cd m(-2) at 25 V.

Capacitive detection of glucose using molecularly imprinted polymers

A novel glucose biosensor based on capacitive detection has been developed using molecularly imprinted polymers. The sensitive layer was prepared by electropolymerization of o-phenylenediamine on a gold electrode in the presence of the template (glucose). Cyclic voltammetry and capacitive measurements monitored the process of electropolymerization. Surface uncovered areas were plugged with 1-dodecanethiol to make the layer dense, and the insulating properties of the layer were studied in the presence of redox couples. The template molecules and the nonbound thiol were removed from the modified electrode surface by washing with distilled water. A capacitance decrease could be obtained after injection of glucose. The electrode constructed similarly but with ascorbic acid or fructose only showed a small response compared with glucose. The stability and reproducibility of the biosensor were also investigated. (C) 2001 Elsevier Science B.V. All rights reserved.

Synthesis and properties of alternating copolymers containing PPV and hole-transporting units for light-emitting devices

A series of alternating copolymers containing triphenylamine (TPA) moieties and oligomeric PPV segments in the main chain have been synthesized by Wittig condensation. The resulting polymers exhibit good thermal stability with decomposition temperatures (Tds) above 305 degreesC under nitrogen at 10 degreesC/min, and high glass transition temperatures (Tgs). They show intense photoluminescence in solution and film. The single-layer electroluminescent device using TAA-PV1 as emissive layer emits green light at 522nm with a turn-on voltage of 6V and maximum brightness of about 200cd/m(2) at 20V.

Nitrogen- and sulfur-containing conjugated polymers as the hole-transporting materials

A series of novel nitrogen- and sulfur-containing conjugated polymers have been synthesized via an acid-induced self polycondensation of functional monomers with methyl sulfinyl group. They exhibit good solubility in common solvents, such as CHCl3, THF, DMF, DMSO, et al; and thus show excellent film-forming properties. They are used as hole-transport layer (HTL) in two-layer light-emitting diodes (ITO/polymer/Alq3/Mg:Ag). The typical turn-on voltage of these diodes is about 4 similar to 5V. The maximum brightness is about 3440cd/m(2) at 20 V. The maximum efficiency is estimated to be 0.15 Im/W at 10V.

The effect of chain flexibility and chain mobility on radiation crosslinking of polymers

Radiation crosslinking of polymers mainly depends on the structure of polymer chain. The flexibility and mobility of chain directly influence the possibility of the reactive radicals recombination. Flexible chain is easier to crosslink than rigid-chain polymer. The latter must be crosslinked at high temperature, as most polymers can only crosslink above their melting point. Structural effect also influences the mechanism of radiation crosslinking of polymers. We find from the results in literature and in our laboratory that, the flexibility chain polymer mainly crosslinked with H type, but the rigid chain polymer mainly crosslinked with Y type. (C) 2001 Published by Elsevier Science Ltd.

Effects of the morphologies and structures of light-emitting layers on the performance of organic electroluminescent devices

Organic electroluminescent devices with a structure of ITO/ploy (9-vinylcarbazole)/tris (8-hydroxyquinoline) aluminum (Alq3)/Mg:Ag are fabricated at different substrate temperatures (77, 298, and 438 K) during Alq3 deposition. It is found that the surface morphologies of Alq3 thin films greatly affect the I-V characteristics of the devices by the contact area between metal cathode and light-emitting layer. There is an increase in the luminous efficiency of the devices in the order 77 K < 298 K < 438 K. We attribute this trend to different structures of Alq3 thin films. (C) 2001 American Institute of Physics.