Pipeline Analog To Ternary Converter

The paper describes the application of the pipelining principle to the realization of an analogue-to-ternary converter. The circuit shows a considerable saving in hard-ware compared with an earlier proposed circuit. The main hardware components used are analogue comparators, subtractors and the delay elements; hence this method of A/T conversion can operate at a higher sampling frequency.

ACIAR Feasibility of farmers managing climate related crop production risk in India

Validation of new Indian seasonal climate forecasting products. In the Indian state of Andhra Pradesh (AP) kharif crops are heavily dependent on summer monsoon rains, where the timing and intensity of the rains affects crop yield. The majority of farms in AP are small and marginal, making them very vulnerable to yield reductions. Farmers also lack access to relevant information that might enable them to respond to seasonal conditions. Enabling farmers to utilise seasonal climate forecasting would allow them to respond to seasonal variability. To do this, farmers need a forecasting system that indicates a specific management strategy for the upcoming season, and effective and timely communication of the forecast information. Current agro-meteorological advisories in AP are issued on a bi-weekly basis, and they are relevant to an agro-climatic zone scale which may not be sufficiently relevant at a village level. Also, the information in the advisories may not be necessarily packaged in way relevant to cropping decisions by farmers. The objectives of this project are to evaluate the skill of seasonal climate forecasts to be issued for the 2008 monsoon season, to assess crop management options in response to seasonal scenarios that capture the range of seasonal climatic variability, to develop and evaluate options for effective communication and adoption of climate forecasts and agricultural advisories, and to synthesise and report on options for future research investments into seasonal climate forecasting.

Thermochemistry and lower combustion limit of ammonium perchlorate in presence of methylammonium perchlorates

The heats of combustion of mono-, di-, tri- and tetramethylammonium perchlorates have been determined by bomb calorimetry. The data have been used to explain why the thermal behavior of ammonium perchlorate (AP) is considerably modified in presence of these compounds as shown by differential thermal analysis. Above a particular concentration of methylammonium perchlorate (MAP), AP ignites in a single step around 290°C. The minimum concentration of a MAP (mono-, di-, tri- or tetra-) needed to cause ignition of AP in a single step depends on intramolecular “elemental stoichiometric coefficient” of the mixtures that has the same value regardless of the MAP. Furthermore, the calorimetric values of these mixtures are the same. The heat evolved on ignition of such a composition appears to determine the lower concentration limit of combustion of its mixture with AP.

A dual-slope analogue-to-digital converter for generating polynomials

A new digital polynomial generator using the principle of dual-slope analogue-to-digital conversion is proposed. Techniques for realizing a wide range of integer as well as fractional coefficients to obtain the desired polynomial have been discussed. The suitability of realizing the proposed polynomial generator in integrated circuit form is also indicated.

Thermal decomposition of ethyl and isopropyl amine perchlorates

Thermal decomposition of ethyl and isopropyl amine perchlorates has been studied by methods such as DTA, TG, isothermal weight loss measurements and the decomposition products have been analyzed in a mass spectrometer. Activation energy values for thermal decomposition have been calculated fromagr-t plots. The proton transfer dissociation mechanism proposed for the thermal decomposition of ammonium perchlorate (AP) has been extended to explain the decomposition products of these twosubstituted amine perchlorates.

Morphological and molecular diversity of Colletotrichum spp. causing pepper spot and anthracnose of lychee (Litchi chinensis) in Australia

Since the 1980s a new disease has been affecting Australian lychee. Pepper spot appears as small, black superficial lesions on fruit, leaves, petioles and pedicels and is caused by Colletotrichum gloeosporioides, the same fungus that causes postharvest anthracnose of lychee fruit. The aim of this study was to determine if a new genotype of C.gloeosporioides is responsible for the pepper spot symptom. Morphological assessments, arbitrarily-primed PCR (ap-PCR) and DNA sequencing studies did not differentiate isolates of C.gloeosporioides from anthracnose and pepper spot lesions. The ap-PCR identified 21 different genotypes of C.gloeosporioides, three of which were predominant. A specific genotype identified using ap-PCR was associated with the production of the teleomorph in culture. Analysis of sequence data of ITS and -tubulin regions of representative isolates did not group the lychee isolates into a monophyletic clade; however, given the majority of the isolates were from one of three genotypes found using ap-PCR, the possibility of a lychee specific group of C.gloeosporioides is discussed.

Non-Abelian monopoles break color. I. Classical mechanics

Monopoles which are sources of non-Abelian magnetic flux are predicted by many models of grand unification. It has been argued elsewhere that a generic transformation of the "unbroken" symmetry group H cannot be globally implemented on such monopoles for reasons of topology. In this paper, we show that similar topological obstructions are encountered in the mechanics of a test particle in the field of these monopoles and that the transformations of H cannot all be globally implemented as canonical transformations. For the SU(5) model, if H is SU(3)C×U(1)em, a consequence is that color multiplets are not globally defined, while if H is SU(3)C×SU(2)WS×U(1)Y, the same is the case for both color and electroweak multiplets. There are, however, several subgroups KT, KT′,… of H which can be globally implemented, with the transformation laws of the observables differing from group to group in a novel way. For H=SU(3)C×U(1)em, a choice for KT is SU(2)C×U(1)em, while for H=SU(3)C×SU(2)WS×U(1)Y, a choice is SU(2)C×U(1)×U(1)×U(1). The paper also develops the differential geometry of monopoles in a form convenient for computations.

Non-Abelian monopoles break color. II. Field theory and quantum mechanics

Many grand unified theories (GUT's) predict non-Abelian monopoles which are sources of non-Abelian (and Abelian) magnetic flux. In the preceding paper, we discussed in detail the topological obstructions to the global implementation of the action of the "unbroken symmetry group" H on a classical test particle in the field of such a monopole. In this paper, the existence of similar topological obstructions to the definition of H action on the fields in such a monopole sector, as well as on the states of a quantum-mechanical test particle in the presence of such fields, are shown in detail. Some subgroups of H which can be globally realized as groups of automorphisms are identified. We also discuss the application of our analysis to the SU(5) GUT and show in particular that the non-Abelian monopoles of that theory break color and electroweak symmetries.

Phosphorus in agricultural soils of Finland - characterization of reserves and retention in mineral soil profiles

An overwhelming majority of all the research on soil phosphorus (P) has been carried out with soil samples taken from the surface soils only, and our understanding of the forms and the reactions of P at a soil profile scale is based on few observations. In Finland, the interest in studying the P in complete soil profiles has been particularly small because of the lack of tradition in studying soil genesis, morphology, or classification. In this thesis, the P reserves and the retention of orthophosphate phosphorus (PO4-P) were examined in four cultivated mineral soil profiles in Finland (three Inceptisols and one Spodosol). The soils were classified according to the U.S. Soil Taxonomy and soil samples were taken from the genetic horizons in the profiles. The samples were analyzed for total P concentration, Chang and Jackson P fractions, P sorption properties, concentrations of water-extractable P, and for concentrations of oxalate-extractable Al and Fe. Theoretical P sorption capacities and degrees of P saturation were calculated with the data from the oxalate-extractions and the P fractionations. The studied profiles can be divided into sections with clearly differing P characteristics by their master horizons Ap, B and C. The C (or transitional BC) horizons below an approximate depth of 70 cm were dominated by, assumingly apatitic, H2SO4-soluble P. The concentration of total P in the C horizons ranged from 729 to 810 mg kg-1. In the B horizons between the depths of 30 and 70 cm, a significant part of the primary acid-soluble P has been weathered and transformed to secondary P forms. A mean weathering rate of the primary P in the soils was estimated to vary between 230 and 290 g ha-1 year-1. The degrees of P saturation in the B and C horizons were smaller than 7%, and the solubility of PO4-P was negligible. The P conditions in the Ap horizons differed drastically from those in the subsurface horizons. The high concentrations of total P (689-1870 mg kg-1) in the Ap horizons are most likely attributable to long-term cultivation with positive P balances. A significant proportion of the P in the Ap horizons occurred in the NH4F- and NaOH-extractable forms and as organic P. These three P pools, together with the concentrations of oxalate-extractable Al and Fe, seem to control the dynamics of PO4-P in the soils. The degrees of P saturation in the Ap horizons were greater (8-36%) than in the subsurface horizons. This was also reflected in the sorption experiments: Only the Ap horizons were able to maintain elevated PO4-P concentrations in the solution phase − all the subsoil horizons acted as sinks for PO4-P. Most of the available sorption capacity in the soils is located in the B horizons. The results suggest that this capacity could be utilized in reducing the losses of soluble P from excessively fertilized soils by mixing highly sorptive material from the B horizons with the P-enriched surface soil. The drastic differences in the P characteristics observed between adjoining horizons have to be taken into consideration when conducting soil sampling. Sampling of subsoils has to be made according to the genetic horizons or at small depth increments. Otherwise, contrasting materials are likely to be mixed in the same sample; and the results of such samples are not representative of any material present in the studied profile. Air-drying of soil samples was found to alter the results of the sorption experiments and the water extractions. This indicates that the studies on the most labile P forms in soil should be carried out with moist samples.

Mesospheric temperature response to variations in geomagnetic activity

Temperature data collected over several years from rocket grenade and other experiments at Point Barrow (Alaska), Fort Churchill (Canada) and Wallops Island (Virginia) have been analysed to determine the effect of geomagnetic activity on the neutral temperature in the mesosphere and to study the latitudinal variation of this effect. An analysis carried out has revealed almost certainly significant correlations between the temperature and the geomagnetic indicies Kp and Ap at Fort Churchill and marginally significant correlations at Barrow and Wallops. This has also been substantiated by a linear regression analysis. The results indicate two types of interdependence between mesospheric temperature and geomagnetic field variations. The first type is the direct heating effect, during a geomagnetic disturbance, which has been observed in the present analysis with a time lag of 3–15 hr at the high latitudes and 36 hr at the middle latitudes. The magnitude of this heating effect has been found to decrease at the lower altitudes. The second type of interrelation which has been observed is temperature perturbations preceding geomagnetic field variations, both presumably caused by a disturbance in atmospheric circulation at these levels.

Microprocessor-based polynomial generator

A new method of generating polynomials using microprocessors is proposed. The polynomial is generated as a 16-bit digital word. The algorithm for generating a variety of basic 'building block' functions and its implementation is discussed. A technique for generating a generalized polynomial based on the proposed algorithm is indicated. The performance of the proposed generator is evaluated using a commercially available microprocessor kit.

Influence of the electric field on the low-temperature thermal decomposition of ammonium perchlorate/polystyrene propellant

An electric field (100 V/cm at 230°C and 150°C) has been applied to ammonium perchlorate (AP)/polystyrene (PS) propellant mixtures in order to understand the low temperature decomposition behavior of the propellant. The charge-carrying species is anionic in nature at 230°C, which could be ClO4−, but is cationic at 150°C, which could be either NH4+ or H+. These results are parallel to that observed for pure ammonium perchlorate (AP) pellets [1]. The burning rate (Image ) of the propellant was found to follow the same trend as that for the thermal decomposition of the propellant on application of an electric field. At 150°C Image was higher at the −ve electrode than at the +ve electrode, but at 230°C just the opposite was observed. Kinetic studies have confirmed that the decomposition of the orthorhombic AP follows two mechanism corresponding to E = 30 kcal mol−1 (180–230°C) and E = 15 kcal mol−1 (150–180°C).

Optimising initial population density, growth time and nitrogen nutrition for assessing resistance of wheat cultivars to root-lesion nematode (Pratylenchus thornei)

Pratylenchus thornei is a major pathogen of wheat in Australia. Two glasshouse experiments with four wheat cultivars that had different final populations (Pf) of P. thornei in the field were used to optimise conditions for assessing resistance. With different initial populations (Pi) ranging up to 5250 P. thornei/kg soil, Pf of P. thornei increased to 16 weeks after sowing, and then decreased at 20 weeks in some cultivar x Pi combinations. The population dynamics of P. thornei up to 16 weeks were best described by a modified exponential equation P f (t) = aP i e kt where P f (t) is the final population density at time t, P i is the initial population density, a is the proportion of P i that initiates population development, and k is the intrinsic rate of increase of the population. The cultivar GS50a had very low k values at Pi of 5250 and 1050 indicating its resistance, Suneca and Potam had high k values indicating susceptibility, whereas intolerant Gatcher had a low value at the higher Pi and a high value at the lower Pi. Nitrate fertiliser increased plant growth and Pf values of susceptible cultivars, but in unplanted soil it decreased Pf. Nematicide (aldicarb 5 mg/kg soil) killed P. thornei more effectively in planted than in unplanted soil and increased plant growth particularly in the presence of N fertiliser. In both experiments, the wheat cultivars Suneca and Potam were more susceptible than the cultivar GS50a reflecting field results. The method chosen to discriminate wheat cultivars was to assess Pf after growth for 16 weeks in soil with Pi ~1050–5250 P. thornei/kg soil and fertilised with 200 mg NO3–N/kg soil.

Public Demand for Safer Speeds: Identification of Interventions for Trial

Speeding is a major contributor to road injuries and fatalities and remains prevalent. Changing community perceptions about speeding is an important priority. Austroads commissioned research to identify a range of potential interventions for future trial and evaluation aimed at creating, increasing, and/or sustaining public demand for safer speeds. This project had three phases: a literature review; consultations with key stakeholders regarding intervention options (including feasibility, and likely benefits and costs of identified interventions); and providing research results, including recommendations for future phases of the program of work. The literature review led to the development of a draft Campaign Strategy targeting nine aims across three themes underpinning this research: 1) creating, 2) increasing, and 3) sustaining public demand for safer speeds on the road. Twenty-one stakeholders commented on the suitability and feasibility of, and likely barriers to, countermeasures within the draft Campaign Strategy and its applicability to the Australian and New Zealand context. There was overwhelming positive support for the proposed Campaign Strategy by the majority of respondents; many, noting that it addressed key misperceptions and complemented many existing approaches. A small number of respondents expressed some concerns with various aspects. Stakeholder feedback was incorporated into the final proposed Campaign Strategy to enhance its potential effectiveness. Wide diversity across jurisdictions makes the recommendation of individual interventions for specific areas problematic. Individual jurisdictions should consider a range of costs and benefits of the proposed Campaign Strategy to determine the likely feasibility from their unique perspective. Issues to be addressed when considering implementation of the proposed Campaign Strategy include speed limit setting policies, resourcing, messaging and advertising strategies, and political will associated with promoting safer speeds.